Search Documents

By N. Kumar Kittusamy

A field study was conducted to evaluate seat designs on shuttle cars. Eight operators participated in evaluating seat designs on the basis of perceived levels of vehicle jarring/jolting and discomfort. Researchers also measured the levels of vehicle jarring/jolting. Four basic seat designs were compared on low and mid-coal seam shuttle cars during production operations at two underground coal mines. Two seats were currently used on the shuttle cars and another two were NIOSH designs. Objective data were collected using accelerometers with pre-amplifiers and filters connected to a data recorder; whereas subjective data were gathered with a visual analog scale (VAS) and a questionnaire. Results from measured levels of jarring/jolting showed that the NIOSH Seat L2A smoothed out bumps better than any other seats. Using the VAS, mid-seam and low-seam shuttle car operators rated the levels of jarring/jolting and discomfort lower with the NIOSH seat than the other seats. Questionnaire responses indicated that operators rated NIOSH seat designs as more comfortable. This research will provide the industry with better seat designs for isolating jarring/jolting in vehicles. Furthermore, researchers plan to improve the NIOSH seats using information gathered in this study.

Jan 1, 2003

By Jr. Smith

The equilibrium compositions of product gases for mixtures of air with methane, propane, or ethylene at and around flame temperatures are reported. For each hydrocarbon, compositions are given for five fuel-to-air ratios--two lean, two rich, and one stoichiometric--at five pressures, from 1 to 20 atmospheres, and at an ambient temperature of 25° C.

Jan 1, 1965

By Alexander E. Morrow

Oxygen breathing apparatus for use in mines was introduced to the United States in 1907. Despite their intended purpose of safeguarding lives, the apparatus led to the deaths of many men because of inherent or developed defects in the equipment, lack of training,, physical shortcomings of wearers, and improper procedures. The Bureau of Mines pioneered in research and training to curb logs of life among users of such apparatus and promoted development of safer equipment and procedures. As a consequence, deaths have been far less frequent. In 1944 the Bureau issued Information Circular 7279, Loss of Life Among Wearers of Oxygen Breathing Apparatus. That publication listed the case histories of 26 deaths that had occurred since the introduction of such equipment to American mining. The author, the late G. W. Grove,3/ asserted that further loss of life could be avoided if good equipment were used, teams were properly trained, and the basic principles of safe procedure were followed. This publication is a sequel to I.C. 7279 and contains information on eight deaths among wearers of oxygen breathing apparatus that were overlooked in the original compilation. It also describes the single death that occurred since I.C. 7279 was published.

Jan 1, 1959

By W. C. Phalan

"Prewar Conditions:Metallic magnesium may be considered a war metal, but a war metal with a future, so far as the industry in the United States is concerned. Its production in the United States prior to 1915, on a commercial scale, was negligible, but imports prior to that year may be taken as a gaze of the demand for the metal. Unfortunately, magnesium was not listed separately by the Department of Commerce prior to the war, among the importations, but was included with other metals, as follows: ""Barium, calcium, magnesium, sodium, and potassium, and alloys of which said metals are the component materials of chief value."" However, the imports of metals enumerated other than magnesium were probably small, so that the importations under the above caption may be considered chiefly metallic magnesium in one form or another and, therefore, is an approximate gage of the demand for the metal in the United States. These imports were as follows:These figures are so close that they give a good idea of the figures for the respective calendar years.Of this prewar use, it has been estimated that about 85 per cent was used annually and in approximately equal quantities in the production of (1) flash-light powder, (2) fire works, (3) aluminum casting work, and (4) nickel and nickel-copper alleys, such as monel metal, etc. The re¬maining 15 per cent was employed for general uses, such as deoxiding brass and other copper alloys in foundry work, and to a small extent in laboratory and research work."

May 1, 1920

By C. M. Palencia

The Bureau of Mines evaluated the potential availability of molybdenum resources from 88 mines and deposits that account for more than 90 pct of the demonstrated resource base in market economy countries (MEC's). For each property, tonnage-cost relationships were developed that indicate the molybdenum potentially available at different average production costs, including a 15-pct rate of return on invested capital. From the 23 MEC primary deposits, 2.5 billion 1b Mo was determined to be potentially available at a price of $411b, rising to 4.7 billion 1b Mo at $8/lb. Copper price-molybdenum tonnage relationships were developed for those mines and deposits from which molybdenum can be recovered as a byproduct of copper production. This analysis showed that another 3.4 billion lb Mo is potentially available based on a copper price of $0.7511b, rising to 4.3 billion lb Mo at $l.00/lb. The United States has been the world's largest molybdenum supplier since 1924. Its remaining resources are sufficient to meet the domestic demand of 57 million lb/yr Mo (averaged for a 10-yr period) through the end of the century. Production from primary domestic mines was suspended during most of 1983 because of oversupply of materials. A major concern is the cheap molybdenum byproducts from foreign copper operations in which employment and the need for hard currency override economics in meeting production goals.

Jan 1, 1985

By Robert Lundquist

REAM is a unique method of rock breaking using high energy projectile impact. This report-describes the most recent in a series of tests demonstrating mining applications for the REAM method. In an underground limestone mine at Greer, West Virginia, REAM was used to drive a short tunnel and drill a large diameter borehole. Along with breakage data from these tests the goal of the program was to examine environmental problems which might result from the use of cannons under-ground. A total of 103 shots was used to advance a 14-l/2-feet high by 10-feet-wide face a distance of 5-1/2 feet. It is estimated that the 9.3-pound-concrete projectiles launched at 5000 feet per second will break an average of 0.78 tons of limestone or 67 percent of the 1.125 tons of granodiorite broken in previous tests. The 9-inch-diameter borehole was drilled horizontally by repeated axial impact for 7 feet, 2-1/2 inches by 21 shots giving an average of 4.12 inches per shot. Scaling this result to compressible impact energy yields an estimated 5.8 inches per shot for a 12.8-inch-diameter hole compared to 8 inches per ~hot for a 16-inch-diameter hole in granodiorite. Noise measurements indicate that a silenced cannon can be used within a few hundred feet of mine personnel in a room and pillar mine within the legal limit of 140 dB impulse without additional protection. Some fume measurements were made with satisfactory results, even though the military propellants used produce much greater quantities of toxic fumes than the liquid propellant proposed for the future.

Jan 1, 1976

By D. H. Baker

THIS REPORT presents the technique and equipment used in determining the hardness of titanium sponge. Detailed descriptions are given of the methods used in preparing test samples for chemical analysis and hardness testing, the method of melting and surfacing test ingots, and the technique of reading Brinell-hardness impressions. The arc-melting furnace described, for which engineering drawings are included, will produce from 70 to 90 double-melted buttons each 8 hours of operation. Experimental data are also presented depicting the effect on hardness of the methods of surfacing specimens, temperature of test specimens, and the effect of time at test load. These data show that surfacing of the specimen involves no critical machining operations but that the test surface must be paralleled by a relatively flat surface for contact with the anvil of the Brinell tester. The heating of a specimen to 150° C. during surfacing does not materially affect the results if the ingot is cooled to room temperature before the hardness impressions are made. The optimum time at load appears to be approximately 30 seconds, but load times of as much as 1/ ½ minutes will not cause major errors.

Jan 1, 1959

By H. L. Gibbs

Many factors contributed to the decision to build a radiochemical laboratory at the Salt Lake City Metallurgy Research Center to investigate the application of radioactive isotopes and chemical compounds in extractive metallurgy. These reasons included the notable success achieved in biological sciences with radioisotopes, the development of reliable instruments and methods for identifying the isotopes and measuring their activities, and the commercial availability of radioisotopes in a variety of forms and known activities. The paramount reason, however, was the realization that better methods were needed for guiding and quantifying research to resolve the complex extractive metallurgy problems under study at the Research Center. This is the first of a series of reports describing the application of radioisotopes and radioactivity techniques in extractive metallurgy. The report includes a discussion of licensing and safety requirements, a general description of the laboratory and the methods used, a definition of the nature and scope of the research program, and a synopsis of the more important problems studied. Subsequent reports will concern radioactive techniques for solving specific problems in mineral dressing, hydrometallurgy, and pyrometallurgy.

Jan 1, 1960

By D. Harrington

The greatly extended use of the underground trolley-locomotive system for hauling coal without doubt was one of the most important factors in the rapid progress of coal mining and the increased production of coal in American coal mines during the period 1910-20. Much of the superior efficiency of production of our underground coal and metal lines should also be credited to the trolley locomotive system. The trend to mechanization of mines during the past 15 years, mere particularly the past 5 years, with higher production per man employed and greatly accelerated advancement of working places, has required increased use of trolley locomotives, necessitating larger equipment, higher speeds, and more 'frequent turn over of pit cars. This is re¬flected in increased size of locomotives and the use of larger mine ears (some with a capacity up to or over 10 tons); moreover, heavier rails and larger-size trolley wires have boon or ought to have boon installed. Trolley-locomotive haulage has proved to be rapid; economical, efficient, and productive; nevertheless; in spite of these advantages, so-many hazardous features and, unsafe conditions are involved and the price paid in life and property is so high as to justify the statement that the system should be scrapped if it cannot be operated under reasonably safe conditions. Since bare trolloy wires were introduced into underground mines, they have boon responsible for the death of hundreds of diners, property damage totaling millions of dollars, an indeterminate loss of tonnage through the abandonment of mines or parts of mines, and loss of time after disasters caused by fires or explosions originated by the trolley haulage system.

Jan 1, 1945

By Earle S. Burnett

Rotating piston deadweight gages have been used for many years for measurement of pressure to several hundred atmospheres. They have been calibrated by comparison of fluid pressures produced by various loads bearing on the piston bases, as measured by corresponding heights of balancing columns of mercury. When expressed in appropriate units, these ratios of column heights to piston loads are called piston constants. Experimental arrangements and procedures for their determination are presented in this paper, followed by a discussion of their significance and of their subsequent applications.

Jan 1, 1966

By Isaac A. Zlochower, Michael J. Sapko, Eric S. Weiss, Kenneth L. Cashdollar

This paper describes dust explosion research conducted in an experimental mine and in a 20-L laboratory chamber at the Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH). The primary purpose of this research is to improve safety in mining, but the data are also useful to other industries that manufacture, process, or use combustible dusts. Explosion characteristics such as the minimum explosible concentration and the rock dust inerting requirements were measured for various combustible dusts from the mining industries. These dusts included bituminous coats, gilsonite, oil shales, and sulfide ores. The full-scale tests were conducted in the Lake Lynn experimental mine of NIOSH. The mine tests were initiated by a methane-air explosion at the face (closed end) that both entrained and ignited the dust. The laboratory-scale tests were conducted in the 20-L chamber using ignitors of various energies. One purpose of the laboratory and mine comparison is to determine the conditions under which the laboratory tests best simulate the full-scale tests. The results of this research showed relatively good agreement between the laboratory and the large-scale tests in determining explosion limits. Full-scale experiments in the experimental mine were also conducted to evaluate the explosion resistance characteristics of seals that are used to separate non-ventilated, inactive workings from active workings of a mine. Results of these explosion tests show significant increases in explosion overpressure due to added coal dust and indications of pressure piling.

By G. G. Huggins

A demonstration project has been completed to reduce the operator sound level of an underground service vehicle, a personnel dispatch wagon, to go dB(A) or less. The program objective was to implement quieting recommendations made on an earlier study for the USBM n diesel-powered mine equipment. The manufacturer and mine to which the vehicle was going actively participated in the program to ensure a product that was not only quiet, but useful. The key element of the quieting package is an engine part a1 enclosure, which, with several complementary noise control components, reduced the operator sound level 14 dB, from 101 dB(A) to 87 dB(A). The vehicle underwent a 4-month trial period, with no degradation in the quieting package. Mine personnel reported no maintenance difficulties, and were enthusiastic about the dispatch.

Jan 1, 1975

By Albert L. Toenges

This report is the second of a series describing methods and systems of mechanical mining; where operations are conducted on more than one shift. The first report, Information Circular 7014,4/ describes mining operations at 14 mines and the present paper describes operations at 11 additional mines. The purpose of this study is to analyze the advantages and disadvantages of the various types of equipment and mining systems now used where more than one shift is worked per day. Physical conditions vary in different and in the same mining districts and determine, together with economical considerations, the systems of mining and the types of mechanical loading equipment to be used. The information presented in this paper may be helpful to operators or others who may contemplate installing a mechanical mining system. The equipment used in the mines described comprises conveyors, scrapers, mobile loaders, mobile conveyors, and combination of these types. The description of the mining systems and practices at the mines investigated is detailed only as they relate to and affect mechanization. In computing the operating data in mines that are not totally mechanized, employees not working directly on production have been charged to output from mechanized sections in proportion to the percentage of mechanization. The operating data for comparing various systems are for an average working dry, as the number of men working on idle days varies greatly in different mines.

Jan 1, 1939

By Galen G. Waddell

Dilation and contraction of the rock surrounding horizontal access open-ings of a deep mine were analyzed during stope advance to determine what type of measurements, made with relatively inexpensive instrumentation, would best reflect the rock behavior. A variety of instruments, mostly mechanical extensometers, were used. Detailed descriptions are given of Down-the-hole extensometers, floating rockbolt clusters, transit surveys, and other instruments and measuring techniques. Although all of the radial-deformation-rate graphs illustrated useful rock behavior data, the most informative graphs were compiled from data procured with the radial extensometers that penetrated, to various depths, the rock around the access openings. An analysis is given of measurement data on the rock around lateral drifts and across and adjacent to the nearly vertical vein of the Star mine, Burke, Idaho. Several useful relationships were found between the rock deformation rate and the stoping process. Information was produced on the elastic state of rock around an underground opening, effectiveness of stope support, rheology of rock, zone of influence around stopes, effectiveness of rockbolts, axis of maximum strain in a plane perpendicular to the long axis of the lateral, and other phenomena. This information could be of particular value in determining location, design, and support of underground openings.

Jan 1, 1966

By Leo A. Schrider

This report analyzes the successful low-pressure gas drive in the Keener sand of the Bonds Creek oilfield, Pleasants and Ritchie Counties, W. Va.) and predicts its future performance. Core analysis from two wells and electrical and radioactivity logs were used to evaluate the reservoir characteristics. Production records over a 37-year period indicate that over 240,000 barrels of oil have been produced from the Keener sand by low-pressure gas injection. Decline-curve analysis shows that 165,000 additional barrels should be recovered from 108 acres of productive sand by continuing this secondary-recovery method.

Jan 1, 1966

By Liming Yuan

A computational fluid dynamics (CFD) study was conducted to model effects of coal properties on the potential for spontaneous heating in longwall gob (mined out) areas. A two longwall panel district using a bleeder ventilation system was simulated. The permeability and porosity profiles for the longwall gob were generated from a geotechnical model and were used as inputs for the three dimensional CFD modeling. The spontaneous heating is modeled as the low temperature oxidation of coal in the gob using kinetic data obtained from previous laboratory scale spontaneous combustion studies. Heat generated from coal oxidation is dissipated by convection and conduction, while oxygen and oxidation products are transported by convection and diffusion. Unsteady state simulations were conducted for three different US coals and simulation results were compared with some available test results. The effects of coal surface area and heat of reaction on the spontaneous heating process were also examined.

Jan 1, 2008

By Jon C. Volkwein

The U.S. Bureau of Mines investigated a method of using inert gas to prevent the formation of explosive gas mixtures in auger highwall mining of coal. A combination of gasoline and diesel engine exhaust gases was introduced into the auger drill hole using a short section of pipe located at the collar. Gas samples were taken and analyzed on-site with infrared detectors for oxygen, carbon dioxide, methane, and carbon monoxide. Evacuated bottle samples were also taken and analyzed by gas chromatography in the laboratory. These gas results were analyzed for explosibility. Coal samples from various depths were used to obtain the gas content of the coal using the modified direct method. Personal expo- sure to carbon monoxide was also monitored. The highest methane level observed was 9.55%. The levels of inert gas (carbon dioxide and nitrogen) were sufficiently high to prevent any ignition of the methane. Results showed that for all conditions during mining, gas concentrations were nonexplosive. The gas content of the coal was about 0.30 cm3/g. The maximum personal time-weighted average Sample for carbon monoxide was 20 ppm. This system provides a safe, inexpensive, simple method for preventing explosions during auger mining.

Jan 1, 2010

By Stephen R. Iverson, Bill M. Stewart, Michael J. Beus

The U.S. Mine Safety and Health Administration (MSHA) has identified ore pass hazards as a significant safety problem in underground metal mines in the United States injury and fatality data show that many injuries are related to pulling or freeing ore pass chutes and structural failures of control gates and ore pass walls. Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are investigating these hazards and developing methods to improve safety during transport of ore and waste. Particle flow analysis methods were used to simulate chute and control gate response to various material loading scenarios. Results from computer models indicate that dynamic impacts from ore and waste rock might be considerably greater than theory predicts. Static and dynamic loads were measured in a laboratory setting using scaled ore (sass mock-ups. Field tests were initiated in an active ore pass to determine actual static and dynamic loads. Field data were compared to computer results and indicated that impact and total static loads were substantially less than the computer model results suggested. Damping factors, normal and shear stiffness, and mass frictional characteristics have a significant effect on particle flow and resulting impact loads.

By F. L. Wideman

This paper lists resources of sulfur in Wyoming, Colorado, Utah, New Mexico, and Arizons, an area comprising approximately 522,600 square miles, Sources of sulfur occuring within the region are sulfur are, pyrite and pyritic ores, and natural gases and petroleum. Data concerning these sources are presented on a statewide basis. Some of the known deposits of sulfur ore are surficial and of fumerole origin; other deposits have resulted from oxidation of pyrite or sulfide ores of copper, lead, and zinc. The deposits are small and the sulfur is distributed erratically in them. There is a small production from some of the deposits, and the material produced is used as soil conditioner.

Jan 1, 1957

By Scott Turner

The settlers of a new country necessarily suffer at first from the lack of accumulated stocks of metals - in-use that are possessed in older countries . Our American colonists were at first compelled to import their metals in manufactured forms , and it must have proved difficult to produce an exportable surplus of commodities with which to pay for them . These circumstances stimulated a search for domestic ore deposits . Various discoveries resulted , so that as early as 1628 , we find the colonists importing two craftsmen from England to establish iron -works in Massachusetts to beneficiate local ores . In 1648 , an iron -works at Lynn was producing metal at an annual rate of 400 tons . Later on , the colonial iron industries became of importance , some metal being actually exported to England . The people of this country thus early became convinced of the necessity for domestic mineral production . It is now little realized how persistent were their efforts to - make mineral discoveries , before the gold- rush to California ; the extraordinary success of our subsequent mineral explorations has overshadowed the earlier record . Precise and complete accounting of our mineral production , having the character of national bookkeeping , is available only for the series of years beginning with 1880 , when commences the official record that is provided by the Government publication called Mineral Resources of the United States . In the period of 52 years , from 1880 through 1932 , the value of mineral production of the United States amounted to more than 122 billion dollars . Only 12 billions of this total were produced in the 21 years , 1880-1900 , while nearly 110 billions were produced in the first 31 years of the present century . Of this 110 billions , over 53 billions were produced in the most recent decade , 1921- 1930 , the production of the previous decade , 1911-1920 , having been only 37 billions , though it included the war period ; that of the decade 1901-1910 was 16 billions . In 1931 , the total value of mineral products of the United States was $ 3,180,000,000 , compared with an average annual value of $ 5,556,000,000 during the previous five - year period , 1926-1930 . The decline in 1931 from that average was therefore 43 per cent . As to the three great groups of mineral commodities , metals fared worst , with a decline of 55 per cent in the value of their production , while the value of fuels declined 39 per cent , as did that of the nonmetals group .

Jan 1, 1933