Search Documents

By Robert C. Merritt

This report describes laboratory as well as pilot heap leaching investigations of low-grade sandstone ores from Wyoming, New Mexico, and Colorado. Sodium carbonate-bicarbonate solutions containing sodium hypochlorite extracted up to 86, 54, and 16 percent U308 from Wyoming, New Mexico, and Colorado ores, respectively. Ammonium carbonate-bicarbonate solutions containing sodium hypochlorite were less effective at leaching these ores. Acid leach in replicate pilot plant testing resulted in U308 extractions of 96, 88, and 81 percent from the Wyoming, New Mexico, and Colorado ores. The development of cost-effective processes for extracting uranium from low-grade ore is essential to the assurance of a continuing domestic supply of uranium.

Jan 1, 1977

By W. E. Lamont

The Federal Bureau of Mines conducted research to develop methods of removing phosphorus from the earthy, calcareous hematite ores of the Birmingham, Ala., iron district while simultaneously improving the grade and recovery of the iron values prior to furnacing. An attempt was also made to identify the phosphorus minerals present in the ores. The ores contained about 36 percent iron, 12 to 16 percent CaO, 15 to 20 percent hydrochloric acid insolubles, and 0.30 to 0.36 percent phosphorus. Fractions containing 5 to 15 percent phosphorus were isolated from the ores. Collophanite, Ca3P2O3?nH2O, a member of the apatite group, was the only phosphate mineral identified. Beneficiation methods using flotation and reduction roasting with magnetic separation yielded good grade iron concentrates, but were not as effective for reducing the phosphorus content of concentrates. Reduction roasting followed by fine grinding, magnetic separation, and acid leaching gave iron concentrates containing 62.5 percent iron and 0.04 percent phosphorus with an iron recovery of 82.9 percent and a phosphorus rejection of 93.7 percent. Reoxidation of reduced magnetic concentrates followed by acid treatment gave iron concentrates containing 58.1 percent iron and 0.02 percent phosphorus with 89.6 percent recovery of the iron and 96.5 percent rejection of the phosphorus.

Jan 1, 1973

This surveillance report summarizes data on work-related fatal and nonfatal injuries, illnesses, and hazardous exposures in the mining industry for the 10-year period 1986-1995. The term ?surveillance,? as used in public health, may be new to many readers of this report. With regard to occupational safety and health, the goal of surveillance is to describe the occurrence of work-related injuries, illnesses, and known hazardous exposures; to identify new hazards that may occur due to the introduction of new technology or other factors; and to assess the effects of preventive measures designed to improve worker safety and health. Surveillance provides an overall picture, which can be used to focus resources on areas most in need of prevention programs or further research. Surveillance generally requires the use of multiple sources of data, all of which have their own strengths and limitations. Surveillance in the U.S. mining industry is complicated by the fact that U.S. national data systems that provide information on mining are based on two different definitions of the mining industry. One is established by the Mine Safety and Health Administration (MSHA), the other by the Standard Industrial Classification (SIC) System [Office of Management and Budget 1987] and the 1980 U.S. Bureau of the Census (BOC) Classification System [U.S. Bureau of the Census 1982].

Jan 1, 2000

By C. M. Keenan

During the 7-1/2 years (January 1945-June 1952), immediately preceding enactment of the Federal Coal Mine Safety Act, 26 major disasters3/ in the coal mines of the United States caused the deaths of 491 persons. In the next 7-1/2 years under the act (July 1952-December 1959), only 12 major disasters occurred. The total killed was 148. This improvement is commendable. However, the continuing frequency of minor fires and gas and/or dust ignitions in the Nation's coal mines, many of which could have been of major consequence, are cause for serious concern to the coal-mining industry and those affiliated agencies engaged in promoting safety in the industry. The data presented in this report have been prepared to make available to the coal-mining industry and related groups an overall perspective of the disaster potential from mine fires and gas and/or dust ignitions in coal mines after 7-1/2 years under the Federal Coal Mine Safety Act. This act, effective July 16, 1952, which amended the original Federal coal-mine investigative act of May 1941, provides under Title II certain enforcible mine-safety provisions designed to prevent major disasters caused by explosions, fires, inundations, and man-trip and man-hoist accidents in coal mines that employ 15 or more individuals underground.

Jan 1, 1960

By D. W. Blaylock

I. The Lower Kittaning bed is the most important bed in Clarion County from the standpoint of present production, but the Clarion bed has the largest recoverable reserve. 2. Known measured and indicated reserves in all beds, based on a minim thickness of 14 inches and 1,800 short tons per acre-foot of coal in place, are estimated at 1,210 million short tons as of January 1, 1952. Of this total, 790 million short tons is in beds 28 inches and mare thick. Areas in some beds were omitted from the estimate because available data relative to the bed characteristics are too wager for ding an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, they should be added to the total estimated reserves.

Jan 1, 1956

Monitoring systems can have numerous uses in the mine. They can aid in the efficient management of the mine by providing environmental trend data, production and maintenance control, and communications. In some cases, they can provide justification to petition the Mine Safety and Health Administration (MSHA) fog a variance of one of the mandatory safety standards. They may also increase the gross revenues of the mine by increasing the amount of coal produced or increase profits by reducing the cost of producing that coal. No single system will satisfy the requirement of all mines. Some may require simple hard-wired status-reporting systems; others, multipurpose computer-based systems that collect, analyze, and store data and perhaps control some mine functions. Even though systems vary in complexity, they are all composed of three functional components. The first component is sensors that measure the environmental or production parameters and produce an electrical signal that is fed into the telemetry. The second is telemetry devices that receive the signal from the sensors and transmit it in either analog or digital format to the third com¬ponent, analysis and display equipment. This equipment receives the transmitted signal and either stores it for later analysis or displays it. The analysis-display equipment ranges from simple strip chart recorders with preset alarms to computers, cathode-ray tubes (CRT's), and line printers that can also provide production reports. 4.2 Uses of a Mine Monitoring System A list of potential uses for mine monitoring systems, including both production-related functions and those related to health and safety, was used to develop a questionnaire. It was presented to representatives of the mining community to determine their current monitoring priorities. The responses indicated that the industry's priorities fall into the following two categories: First priority- Production and haulage Maintenance Second priority- Ventilation Communication Fire monitoring Personnel The survey shows that production-oriented systems were the most appealing to the questionnaire respondents. Since even small improvements in production efficiency and maintenance can have a large financial impact, the desirability of monitoring systems that focus on these areas is understandable. The results are summarized in table 4-1. The function that scored 100 was viewed as the most beneficial monitoring function.

Jan 1, 1984

By R. M. Creamer

Attempts have been made to electroplate titanium and zirconium from aqueous, nonaqueous, and fused-salt electrolytes. Metals were produced only in fused-salt electrolytes, the major product being sponge metal. All other electrolytes gave only partial reduction of the metal ions. Fused alkali borate electrolytes containing titanium salts gave titanium boride powders and coatings of poor adherence. Some of the problems encountered in the deposition of these metals and some of the aspects of titanium and zirconium chemistry involved are discussed. INTRODUCTION Titanium and zirconium are both relatively light, noncorrosive metals with both military and civilian uses. This has led to intensive investigations into the metallurgy of these metals. Both metals are high in the Electrochemical Displacement Series and are difficult to prepare in a pure state. At present they are prepared by reducing their chlorides, using magnesium. Electrolytic reductions have resulted in the preparation of fine powders or sponge of variable quality. It is believed that a good process of electroplating these metals on a baser metal would result in a very desirable product. The objective of the research summarized in this report was to investigate methods of electrodepositing these metals, with the idea of producing uniform, coherent plates. Most of the work was concentrated on titanium, the more abundant of the two metals. A system developed for titanium should be applicable to zirconium owing to their chemical similarity. Information gained from these experiments may also be applicable to the electro-winning of the metal.

Jan 1, 1954

By R. O. Dannenberg

A metallic displacement process, utilizing easily available steel wool or steel window screen, was devised and successfully used for the recovery of silver from waste photographic fixing solutions. Laboratory and prolonged commercial-scale testing established that the iron filament type unit will efficiently precipitate silver, as a high-grade sludge, from acidic waste photographic fixing solutions ranging in grade from less than 1 to over 10 grams of silver per liter. Data and design information are presented to facilitate the construction and operation of a practical unit of any desired size. A smelting process for recovering pure silver from precipitated sludge containing 27 to 80 percent silver was devised.

Jan 1, 1968

By Robert F. Chaiken

More than 500 fires are now burning in abandoned coal waste banks and coal deposits in the United States. Once established, such fires can burn for decades, and extinguishing them by conventional methods such as surface sealing to exclude air, excavation to remove fuel, or flushing to cool the fire zone is usually difficult and always expensive. Burnout Control, a technique developed by the Bureau of Mines for the control of abandoned fires, involves the accelerated combustion of coal in place with total management of the heat and fumes produced. A burning waste bank or mine is placed under negative pressure relative to the atmosphere, and heat and combustion products are drawn from the combustion zone through an exhaust ventilation system. Heat produced appears as sensible heat in the exhaust, at temperatures as high as 1,000° C (1,832° F), and can be recovered for the production of steam, hot water, process heat, or electricity. The Bureau's first field demonstration of Burnout Control was at Calamity Hollow in Allegheny County, PA (near Pittsburgh). Calamity Hollow was the site of an underground mine in the 1900's and was surface mined in the 1940's. In the winter of 1961-62, a fire of undetermined origin was discovered in the exposed coal. In 1963, the Bureau constructed a trench barrier around the fire and a surface seal over the affected area. The fire was isolated, but not completely extinguished. In 1979, when the Bureau began work on the Calamity Hollow Mine Fire Project, to demonstrate controlled burnout, the fire was still smoldering on the hot side of the trench barrier. The project, which was begun in December 1979 and ended in July 1982, consisted of the design, construction, operation, and subsequent dismantling of a Burnout Control ventilation system. This report is the fourth in a five-part series that describes the Calamity Hollow Mine Fire Project. The first report, part 1, describes the design and construction of the field installation. Part 2 will present the results of a continuous 4-month burnout operation. (Because part 2 involves the analysis of a substantial body of data, it will not be published until after publication of parts 3, 4, and 5). Part 3 describes the instrumentation used to control and monitor the progress of the burnout operation. This part (part 4) and part 5 both deal with the closeout phase of the field demonstration. The quenching of the fire is described in this report, and part 5 will describe the final excavation and backfilling of the heated zones. The reports in this series document the Calamity Hollow controlled burnout demonstration, which showed that (1) controlled in situ combustion is a feasible method for controlling underground fires in abandoned mines, (2) the resultant thermal exhaust output is sufficient for energy utilization, and (3) water injection with fume exhaustion is a potentially effective method for cooling large underground fire zones. Further trials of both Burnout Control and water injection with fume exhaustion are planned.

Jan 1, 1984

By Steven J. Page

Accurate measurement of workplace respirable dust concentration is an essential step in eliminating lung disease in any occupational setting. In the United States (U.S.) coal mining industry, this measurement process has relied upon a personal sampler that includes a 10 mm Dorr-Oliver (DO) nylon cyclone operated at a flow rate of 2.0 L min-1 to collect a respirable dust sample. Dust concentrations measured with this sampler are multiplied by 1.38, which was empirically derived, to convert them to measurements approximating the United Kingdom British Medical Research Council (BMRC) definition of respirable dust upon which the health effects of coal mine dust are based. The International Organization for Standardization (ISO) subsequently refined the respirable dust definition and the U.S. National Institute for Occupational Safety and Health (NIOSH) 1995 Criteria for a Recommended Standard presented a conversion multiplier of 0.857 to apply to the 2.0 L min-' DO (in addition to thel.38 multiplier) to obtain equivalent ISO concentrations, as approximated by the 1.7 L min-1 DO. However, the conversion multiplier 0.857 was derived indirectly from a limited size distribution data set rather than a direct comparison of the DO samplers. The present analysis focuses on providing a more accurate conversion multiplier derived from direct comparisons of the 2.0 L min-1 (with 1.38 BMRC equivalency multiplier) and 1.7 L min-1 DO cyclones. A weighted linear regression analysis of this database suggests that a more accurate estimate of the conversion multiplier is 0.815.

Jan 1, 2009

By P. M. Sullivan

At its College Park Metallurgy Research Center in Maryland, the Bureau of Mines has installed and is operating a 5-ton-per-hour pilot plant for continuous mechanical separation of values contained in raw urban refuse. The entire sys tern was assembled using commercially available equipment. The process relies on multistage processing including shredding, air classification, screening, gravity concentration, and electrostatic separation. Compactor trucks deliver raw refuse collected along typical routes in metropolitan Washington, D.C., to the pilot plant. The loads are separated into concentrates of (1) light-gage iron, (2) massive metals, (3) glass, (4) putrescibles and waste combustibles, (5) paper, and (6) plastics. While some refinements remain to be made in the processing system flow-sheet, the data obtained to date have been highly encouraging, indicating favorable economics for commercial-size plants.

Jan 1, 1973

By A. Landsberg

Kaolinitic clays are potentially a vast domestic resource for aluminum. Utilization of this resource could decrease or eliminate the nearly complete dependence of the United States on foreign raw materials for this important metal. Furthermore, processing of clay to aluminum through anhydrous chloride metallurgy could reduce the high electrical energy requirements of the conventional Hall-Heroult aluminum reduction process. Several anhydrous chloride processes have been proposed; however, unresolved technical problems have prevented their commercialization. In particular, an acceptable chemical means has not been found to extract aluminum from clay as a highly pure anhydrous aluminum chloride. This Bureau of Mines report identifies and discusses the important chemical problems involved in achieving an acceptably rapid, self-heating, selective chlorination reaction and the subsequent separation of iron chloride byproduct from the anhydrous aluminum chloride.

Jan 1, 1983

By W. D. Riley

The U.S. Department of the Interior, Bureau of Mines, has been conducting minerals recovery research in support of the nation's geothermal program since 1974. The Bureau's program of laboratory and field studies has focused on determining the materials of construction for geothermal resource recovery plants and an the recovery of mineral values from the geobrines. An analytical program has been conducted at the Avondale Research Center to determine the chemical constituents of some high- and low-salinity geobrines found in the Imperial, Valley of California. Data are reported for the early stages of brine production of femur geothermal wells--the low-salinity, medium-enthalpy brines from the East Mesa Known Geothermal Resource Area (KGRA), Mesa 6-1 and 6-2, and the high-salinity, high-enthalpy brine from the Salton Sea KGRA, Magmamax 1 and Woolsey 1. The reported results indicate the importance of the operating and engineering history, the operating parameters during sampling, and the method of sampling in order to evaluate the chemical analyses.

Jan 1, 1980

By J. A. Holmes

As part of its investigation of methods of increasing the efficiency of fuel resources, the Bureau of Mines is continuing the study of the general problems involved in the economic use of fuels in gas pro- ducers that were carried on by the technologic branch of the United States Geological Survey. In the course of this study many inci- dental problems of prime importance have demanded consideration. Among them is the determination, under practically constant con- ditions, of the duration of gas-producer tests necessary to reduce the possible error to a minimum. A discussion of this proper length of test period forms the first part of this bulletin. An attempt to dispel some of the uncertainties that arise in an investigation or to account for some of the minor phenomena often necessitates a systematic and careful study of certain chemical, ther- modynamic, or physical laws, or a combination of these, which in turn may result in information or conclusions of great value. Fur- thermore, seemingly unimportant observations often prove to bear directly upon the design, construction, or manipulation of the machine under test. In attempts to improve the gas producer considerable attention has been given by manufacturers to such questions as fixing or isolating the combustible components of the tar, utilizing the waste heat of the producer for the generation of the steam required by the plant, apply- ing the suction principle to bituminous coal and other tarry fuels, and many allied subjects. Little study, apparently, has been given to the physical-chemical conditions most suitable to the formation of hydro- gen and of carbon monoxide, with a view to regulating the percentages of these gases in generators using fuels other than anthracite coal or charcoal. An attempt was made to introduce such investigations when the operations of the government coal-testing plant began at the Louisi- ana Purchase Exposition in St. Louis in 1904, but owing to adverse conditions these problems were abandoned until the plant was trans- ferred to Norfolk in 1907. The delay in beginning this line of inves- tigations, together with the short testing season at Norfolk, limit the second part of this report to preliminary physical-chemical studies, which, however, were sufficiently significant to warrant careful ex- amination pending more complete researches, which are being carried on at the station located in Pittsburg.

Jan 1, 1911

By C. M. McCulloch

The methane content of virgin bituminous coalbed can now be measured accurately in the field with exploration core samples from vertical boreholes. The gas content of the coal per unit weight can be used either to design a mine ventilation system or to determine if degasification of the coalbed will be necessary before mining, and to determine the gas resources in the coalbed. The equipment necessary to conduct the test costs less than $50. The gas con-tent of the coal in place in the ground is determined by summing the gas lost from coring, gas measured during desorption, and the residual gas in the coal. Upon removal from the borehole, the core sample is placed in an airtight container and des orbed for several weeks until the desorption rate is below 0.05 cm3/g for 5 consecutive days. The gas lost from the core while it was being cored and the residual gas are estimated by a new graphical method. The amount of gas remaining depends upon whether the coal is friable or blocky. Friability appears to relate to the depth of the sample below the surface, fixed carbon percentage, Hardgrove grindability index, and proximity to tectonic disturbance. Friable coals emit nearly 96 pct of the total gas during desorption whereas a blocky coal emits only 60 pct of its total gas. Coalbeds that are ill defined as to their blocky or friable nature must be tested in the laboratory for unambiguous analysis.

Jan 1, 1975

By S. C. Rhoads

The Bureau of Mines is investigating low-chromium alloy substitutes for type 304 stainless steel (type 304 SS). The purpose of the research is to reduce the chromium content in austenitic stainless steels used for corrosion-resistant applications. Nine Fe-9Cr-12Ni alloys containing additions of 0 to 5 pct Mo, 0 to 2 pct V, and 0 to 2 pct Cu were selected for evaluation. All of the experimental alloys containing 5 pct Mo and an alloy containing 2Mo-2V-2Cu possessed structure and tensile strengths similar to those of type 304 SSe Alloys containing SMo-2V and SMo-2V-2Cu had ac-ceptable welding properties as measured by the Varestraint test. Alloys containing at least 2 pct Mo had cQrrosion resistance comparable to that of type 304 SS in solutions of nitric acid, phosphoric acid, acetic acid, and citric acid. In chlorides, all the experimental alloys were susceptible to localized corrosion and stress corrosion cracking similar to that of type 304 SSe The corrosion properties were established by weight-loss tests, electrochemical polarization tests, and stress-corrosion cracking tests. An Fe-9Cr-12Ni-SMo-2V alloy and an Fe-9Cr-12Ni-SMo-2V-2Cu alloy had a combination of welding properties, tensile properties, and corrosion resistances that were most comparable to those of 304 SS.

Jan 1, 1984

By H. R. Batchelder

Much information on oxygen production and the manufacture of synthetic liquid fuels has been published during the past several years. From time to tine the investment and operating cost of oxygen plants of various sizes has been estimated. Surveys have been made so that the various processes by which oxygen is produced commercially might be compared. The gas-making processes in which oxygen is employed, which wore used in Germany during the war, have been described in T.O.M. reels, and this information has been published. Descriptions of pilot-scale or proposed commercial plants for the production of synthesis gas or hydrogen and their conversion to synthetic liquid fuels also have been published. In general, each of these publications has dealt with a particular phase of the over-all problem. The present paper will discuss the relationship between these phases: The factors that affect oxygen manufacture and costs, the methods for the use of oxygen and for the production of synthetic liquid fuels, and, to some extent, the economic factors that must be considered.

Jan 1, 1951

By James S. Browning

The Bureau of Mines conducted laboratory batch and pilot plant flotation tests to determine the technical feasibility of recovering commercial-grade mica from a California micaceous schist. Best results in the laboratory batch tests were obtained using sodium carbonate and sodium silicate for pH control and quartz depression, and a combination of fatty acid and cationic reagents as the mica collector. In continuous pilot plant flotation tests, an alkaline fatty acid-cationic method recovered about 70 percent of the mica in a concentrate analyzing 95.6 percent mica.

Jan 1, 1965

By Stanley M. Walker

Safety consciousness is not a constant for which a specific value can be assigned, but is a variable, which is frequently intangible. Its evaluation is not simple. We all know that safety consciousness is the most potent factor in the prevention of accidents. Safety consciousness may be defined as awareness of hazard and alertness to danger, which controls every action of an individual through his desire to remain alive and uninjured.

Jan 1, 1951

By Mark W. Ryan

The U.S. Bureau of Mines conducted a study to determine if commercially available automatic sprinklers could withstand the high static pressures in deep underground coal mines without leaking and if exposure to the mine environment affected their leak pressures. New sprinklers and sprinklers exposed to the mine environment were subjected to increasing pressures until leakage occurred. The average leak pressures of the new sprinklers ranged from 640 to 2,300 psig and were significantly different for sprinklers from different manufacturers and for different types of sprinklers. Generally, standard-response sprinklers withstood higher pressures than fast-response sprinklers. The results indicated that most commercially available sprinklers would withstand the high static pressures in deep underground coal mines; however, they would not provide the same reliability and safety factor as sprinklers used aboveground at or below their rated pressure of 175 psig. The average leak pressures of the sprinklers exposed to the mine environment ranged from 740 to 1,180 psig. The mine environment affected the ability of 66% of the sprinklers to withstand high static pressures. New sprinklers were also evaluated at pressures of at least 500 psig for 30 days to determine their ability to withstand long-term exposure to high static pressures; no leakage was observed.

Jan 1, 2010