Search Documents

By C. B. Davison

One goal of the Bureau of Mines is to conserve the Nation's mineral resources by developing improved performance materials. Consistent with this goal, the Bureau conducted studies on the formation of undesirable cristobalite in seven different fire clays used as refractories. The studies employed scanning electron micrography, chemical and X-ray analyses, and pyrometric cone equivalent determinations to examine the sample clays and determine the effect of thermal history and stablilizing additives on the amount of cristobalite in various calcines. This research has indicated that as fire clay calcining temperatures increased from 1390° to 1,490° C there was a gradual decrease in the percent of cristobalite present in the calcines and a progressive development of mullite crystallization. No cristobalite was found in fire clays calcined above 1,550° C, but cristobalite reappeared when the calcines were reheated to temperatures between 1,400° and 1,500° C. The research also revealed that additions of lithium fluoride (LiF) prevented formation of cristobalite in fire clay calcines.

Jan 1, 1979

By L. O. Bacon

This Bureau of Mines report summarizes the results of laboratory work in the design of instrumentation for obtaining the dynamic tensile strength of rock at minimum loading. Minimum loading is defined as the lowest tensile loading by pulse reflection to cause fracturing. The instrumentation for obtaining dynamic tensile strengths of rock cores evolved into the use of a compressed-air pellet gun to impact one end of a rock core, suspended by wires, at increasing increments of air pressure. Maximum strain was measured on most or all of the impacts, and the strain at fracture of the core was obtained by extrapolating the pellet velocity-strain curve to the pellet velocity at fracture. Stress at tensile fracture was obtained from the maximum s train, and the dynamic Young's modulus was calculated from the rod velocity by using simple rod theory.

Jan 1, 1962

By H. V. Makar

An aluminizing dross which is accumulating as a waste material in substantial quantities was tested for possible use as a steel deoxidizer. This material, consisting mainly of aluminum, silicon, and iron, was used to deoxidize laboratory-scale melts ranging from 7 to 100 pounds. Oxygen analysis showed that the aluminizing dross was effective in reducing oxygen levels in steel. A direct comparison with aluminum wire showed the dross material to be at least as effective. Under similar test conditions with 7-pound melts, 3 grams of aluminum reduced the oxygen concentration from 210 to 175 ppm, while 4 grams of aluminizing dross (equivalent to approximately 2 grams aluminum) reduced the oxygen concentration from 250 to 170 ppm. An additional 4 grams of aluminizing dross produced a final oxygen concentration of 140 ppm.

Jan 1, 1972

The first steps in the process of mine evacuation are the recognition of a problem and an attempt to communicate the problem to miners who may be affected. This chapter will focus on the way that a problem, fire, came to the attention of mine personnel and the messages that were sent to miners in the affected areas. The concept of information uncertainty, which was introduced in chapter 4, will be discussed as it influences problem perception and diagnosis. Sociotechnical and interpersonal communications will be explored and suggestions for improving these systems will be offered. It might seem that the first indication of a dangerous fire would motivate individuals to take self-protective action, to evacuate the affected area or structure, and to provide clear warning to others who are in danger. Research has actually shown that in most situations this does not occur. Instead, time is taken to gather more information, confirm information that is provided, and consider possible alternative explanations that could account for the given circumstances [Canter 1990; Scanlon 1979; Bickman et al. 1977]. This process of confirmation can lead to the loss of critical time. Canter [1990] summarizes the problem in his book, which reports studies of a number of fire events: "As discussed throughout this book, ambiguity and confusion, incoherent instructions and time-wasting actions, lack of appropriate instructions and misunderstanding of the nature of the event that is unfolding, are all hallmarks of fires and emergencies that kill people." In this chapter, the detection of each mine fire and the communication of warning to endangered miners will be reviewed with an emphasis on how those processes were affected by the availability and use of information. Information can become available through a variety of mechanisms during an emergency situation. First, cues may be taken directly from the environment. Smoke is an obvious example. Secondly, mechanical devices, such as smoke detectors, may provide warning messages. A third source of information is interpersonal communications. These can occur face-to-face or through some mechanical device such as a telephone. With all three methods there is a possibility of miscommunication, misunderstanding, and misinterpretation. All of these means of communication were used with varying degrees of success in the three mine fires analyzed here. A fire, like any nonroutine situation, engenders uncertainty about a diagnosis and understanding of the problem [Mead 1938]. This uncertainty leads to delays in realization of the seriousness of the situation and therefore in the proper response to it. Delay in action is an important concern in any fire setting, but is even more at issue in underground coal mine fires. Mine fires are qualitatively different from structural blazes: workers' escapeways may be miles long; the seam height at many operations is so low that it is impossible to walk upright; access to underground workings is always limited to a few (sometimes only two)

Jan 1, 2000

By Alden H. Emery, J. J. Forbes

"IntroductionThe data contained in this paper were collected during the course of an investigation which covered 15 representative coal mines in 6 coal-mining States. The purpose of the investigation was to determine by atmospheric sampling how much dust was raised into the air during the various operations of coal mining, such as undercutting with machines, loading coal by hand, and transporting it from the working face to the surface. The data thus obtained were considered from two angles - namely, the possible physiological effect of inhalation and the explosion hazard of the dust. No attempt will be mode to discuss the former factor in this paper.CONDITIONS OF MININGThe mines in which this investigation was conducted were considered representative, and it is believed that the results obtained will suffice for the average dustiness encountered in most coal mines. .All of the coal mined was bituminous, from beds 30 to 120 inches thick. Only the ordinary room-and-pillar system of mining was employed. Daily production ranged from approximately 700 to 1500 tons and the men employed from 150 to 450. Coal was undercut by short-wall mining machines in all mines, with the exception of one in which pick mining was employed. Loading at the face was done by miners; none of the mines used mechanical loaders. Electric drills, both for brushing roof and for shooting coal, were commonly used although some roof work was done with jack-hammers and a. little of both with augers. Coal was hauled by motor, mule, or rope power in end-gate cars with capacities ranging from 1600 to 3600 pounds. With few exceptions, coal was won at the face by dry methods - that is to say, no water was employed fox wetting down the dust either during undercutting, loading, or transportation."

Feb 1, 1927

By F. P. Haver

The Bureau of Mines has investigated the electrochemical reduction of lead chloride as a method for producing lead without the pollution problems associated with smelting. It was determined that high-purity metal (>99.9 pct Pb) could be obtained, using PbC12 prepared by ferric chloride leaching of galena concentrate: PbS + 2FeCl3?PbCl2 + 2FeC12 + S°. Optimum results in small-scale electrolytic tests were achieved with a bath consisting of 40 to 70 wt-pct PbCl2 dissolved in KC1-LiCl eutectic, an operating temperature of 450° C, a current density of 2.5 amp/in2, and an electrode spacing of 0.5 inch. In large-scale tests made to develop a cell design for commercial application, the optimum electrode arrangement proved to be a bipolar configuration with horizontal plates. This gave a current efficiency of 86 pct with an energy requirement of 0.52 kwhr/lb lead. To determine the effect of impurity buildup in the bath, 1,200 lb of PbC12 prepared by ferric chloride leaching of galena concentrate was electrolyzed over a period of 2 months. Little deterioration of the metal quality occurred in that time; all of the lead produced had a purity equal to or better than corroding grade (>99.94 pct Pb).

Jan 1, 1976

By G. M. Potter, S. J. Hussey, R. Havens

The Artillery Peak manganese ores , from one of the largest known manganese deposits in the United States , present a difficult problem in concentration because they are low-grade and the association of manganese and gangue minerals is intimate and complex. The known size of this deposit has justified investigation of processes such as leaching, wherein preliminary enrichment of the original feed might be advantageous .. Therefore , the ore-dressing studies on Artillery Peak ores were carried on with the object not only of making directly marketable manganese products but also of removing acid-consuming calcite and raising the grade of ore for leachingplant feed . Owing to the extent of the deposits , test work was carried on at the Salt Lake laboratories in considerable detail on several lots of ore of varying composition . This paper summarizes the results obtained from laboratory testing of four samples obtained by engineers of the Mining Branch from the Maggie Canyon area of the Artillery Peak deposit . Also included are results obtained from testing one sample of Chapin Group ore , which was considered representative of numerous very low-grade ores submitted from the Artillery Peak district . During the course of the investigations , many data were obtained and compiled , but for the sake of brevity , data of secondary importance have been omitted or condensed and only those tests giving the more pertinent results are discussed in detail ...

Nov 1, 1947

By Rethel L. Hubbard

Fourteen straight-run asphalts were prepared in the laboratory from bitumens obtained from three sources: (1) native bitumen from Rozel Point, Utah, (2). bitumen extracted from Athabaska bituminous sandstone at Canada, and (3) bitumen extracted from Edna bituminous sandstone outcropping in San Luis Obispo County, to seven asphalts with penetrations ranging from 19 to 287 at 77 F. were prepared from each of the bitumens. The yields of the prepared asphalts ranged from 74.5 percent for a 27-penetration asphalt from the Athabaska bitumen to 99.5 percent for a 271-penetration asphalt from the Rozel Point bitumen.

Jan 1, 1949

By G. A. Apell

"SUMMARYThe quality of Moose Creek coal is considered superior to that of any now being produced in the Matanuska field of Alaska. In rank it is classed as roar coking high-volatile B bituminous coal.At present the Moose -Creek mines are accessible from the Glenn highway by 6 miles of well-maintained gravel road. The nearest railroad loading point is Moose Creek siding; 7 miles by road from the Buffalo mine. Palmer, 12 miles south of Buffalo mine, is the nearest town. Anchorage is 50 miles south of Palmer by road and-railroad.Core drilling and trenching by the Bureau of Mines revealed 2,375,500 short tons of coal in the Buffalo series on the Buffalo Coal Co. leasehold. Of this, 514,200 tons is considered measured coal and 489,900 tons indicated coal. Existence of deeper beds over the same length increased the tonnage of coal of all categories to 3,279,300 tons. The property has an assumed life, of 16 to 22 years, depending on the number of beds mined, based on an output of 500 tons of coal a day and 100-percent recovery. Coal from some of the beds car be marketed without washing however, a washery is necessary if all beds are mined. Beds in the Buffalo series not mined in the ""first mining"" will be irrecoverable at any later date.The Bureau of Mines completed exploration of approximately one-third of the local coal-bearing areas during 1943. Knowledge gained from this work makes it possible to investigate the rest of the area by drilling an estimated additional 5,000 foot of hole."

Dec 1, 1944

By Wilbur A. Haley

One of the purposes of the investigation was to determine and report on how coal augers are used to mine bituminous coal that is near outcrops and may not be mined otherwise by any other present-day method. Such increased overall recovery results in the conservation of coal resources. Other reasons for the investigation were to determine and report the production rates of such operations and the types of equipment used. Auger mining of coal as a means of coal recovery supplementary to strip mining has been introduced and developed since World War II. This type of coal mining has grown rapidly, and bituminous-coal production by auger mining has been estimated at 6,000,000 tons in 1955. Mines were selected for study to give reasonably representative information on auger mining in different types and thicknesses of coal beds in different geographic areas and on different types and sizes of equipment operated under various conditions. This report is based on field studies of 8 auger-miming operations in Pennsylvania, West Virginia, and Ohio and in 5 different coal beds. Operations were observed in active strip mines, in strip mines reopened for auger mining, and along benched coal-bed outcrops. At the time of this study, no augers were reported to be operating in underground mines. The diameters of holes drilled ranged from 26 to 52 inches, and the lengths of holes ranged up to 208 feet. At some operations auger holes often penetrated abandoned underground mine workings.

Jan 1, 1957

By Joseph M. Pugliese

This work was done by the Bureau of Mines to provide quarry operators with an uncomplicated, first-approximation method for designing blast patterns, considering geologic structure, and to show the valid use of the technique by comparing drill and blast pattern dimensions used in the quarry with those determined by the presented method. The author visited 12 limestone and dolomite quarries in Ohio (Adam, Crawford, and Highland Counties), Wisconsin (Milwaukee, Racine, and Waukesha Counties), and Minnesota (Fillmore, Olmsted, and Wabasha Counties); observed the blasting practices; studied the major geologic features; and after discussion with the quarry managers, foremen, and blasters, compared the quarry blasting patterns with those as calculated by the empirical formulas (after R. L. Ash), with geologic structural considerations. When geologic structure such as bedding, jointing, folding, and caves, as well as explosive properties and field performance characteristics are accounted for in a manner suggested by the research, the presented empirical formulas may be used as a good first approximation. The included steps in planning a blast design and generalized blast patterns should be of help to the quarry operator. Design changes are recommended for those quarries where problems are occurring.

Jan 1, 1972

By Lloyd H. Banning

ELECTRIC smelting tests were conducted at the Northwest Electro-development Experiment Station, Albany, Oreg., to develop a feasible process for producing silicomanganese from siliceous manganiferous material. The Jackson County, Oreg., material used was massive and contained rhodonite as the most abundant mineral. Both raw and beneficiated materials were tested; various proportions and types of fluxes and reductants were used to make up the furnace charges. The silicomanganese product was used successfully in manufacturing various steels at industrial plants. The manganese content of the samples ranged from 23 to 28 percent; silica plus alumina content was as high as 55 percent-about four times the maximum specification for Metallurgical-grade ore. Sink-float laboratory tests indicated that the manganiferous material was amenable to beneficiation. Over 2 tons of rhodonite concentrate was prepared for smelting tests in a sink-float operation. Only the minus-3/4-inch, plus-8-mesh fraction was fed to a heavy-medium cone; over 97 percent of the manganese was recovered in the sink product, which contained 32.4 percent manganese and 44 percent silica plus alumina. About 25 percent of the silica was removed in the float product.

Jan 1, 1959

By John A. Davis, John Gross

Six tests were made by the Alaska Station of the Bureau of Mines on a sample of black sand delivered to the station by Messrs. James, Eagan & Griffen from Fairbanks Creek, Fairbanks mining district, Territory of Alaska, to devise a method of recovering the gold content. More than 90 per cent of this black sand consisted of magnetite and garnet which can be separated magnetically. The Station has no equipment for magnetic separation other than an electromagnet similar to the one used by Day and Richards, (Day, D.T., and Richards, R.H., Investigations of Black Sands from Placer Mines, U. S. Geol. Survey, Bull. 285, 1906, pp. 150-163), which can only be used satisfactorily on small samples. To treat the entire lot of black sand with this machine would have been impracticable. Therefore only a small part of the sand was so treated, the rest being divided into five lots in order to obtain comparative results from other methods of treatment.

Aug 1, 1920

By Eugene T. Sheridan

The 23d annual survey of the peat industry by the Bureau of Mines, United States Department of the Interior, revealed that 75 producers in 17 States re-ported commercial production of peat in 1956. Forty-seven producers reported humus production, 19 reported reed-sedge peat, 17 reported moss peat, and 1 reported muck. This total exceeds the number of active operations, but several producers reported recovering more than one type of peat. Fifty-five percent of the total production was reported as peat humus, 30 percent as reed-sedge peat, and 15 percent as moss peat. A negligible amount was reported as other types. More than one-fourth of the total output was raw peat with no preparation, other than having been air-dried. The remainder consisted of processed peat prepared for use by cultivation, shredding, or kiln drying.

Jan 1, 1958

By Carl L. Bieniewski

U.S. molybdenum production increased fivefold from 18.2 million pounds in 1946 to 90.5 million pounds in 1966, and constituted 87.3 percent of the total free world supply in the 1946-66 period. Mining development in other free world countries in the next few years may reduce the magnitude of the U.S. position, although similar development planned for the United States may counteract some of the relative gains by those countries. In 1966 two-thirds of the reported molybdenum consumption in the United States by end uses was as an alloying element in steel. Molybdenum also has important use as an alloying element in iron and high-temperature alloys. Consumption of molybdenum metal for making fabricated parts has increased in the past few years, especially in the space and nuclear industries. Molybdenum compounds are used mainly for making pigment, catalysts, and lubricants. Based on producer reports of shipments of primary products to domestic customers, U.S. consumption of molybdenum increased from 16.5 million pounds of molybdenum in 1946 to 65.6 million pounds in 1966. U.S. molybdenum reserves are now estimated to be 5.9 billion pounds of recoverable molybdenum, an increase of 2.1 billion pounds above previous estimates. Molybdenum ores account for 71.4 percent of the reserves, copper ores for 22.3 percent and copper-molybdenum, tungsten, and uranium ores for 6.3 percent. Several methods for predicting future demand are illustrated and estimates of demand using these methods were made for 1975. Based on present capacities and announced company plans for future developments, estimates of annual production were made for 1967 through 1975 for the United States, Canada. Chile, Peru, and the free world. These data indicate that molybdenum production in 1975 for the free world is expected to be 246 million pounds with the United States producing 68.2 percent and Canada, Chile, and Peru 30.3 percent.

Jan 1, 1970

By V. F. Parry

Under the present emergency every consumer should store as much coal as he can. Although there is no shortage of coal, there is likely to be a shortage of labor to mine excessive quantities in the fall, and railroads cannot be expected to deliver coal promptly on account of the need for transporting war materials. Some miners must join the armed forces, and those who are left may be unable to mine coal as rapidly as you will need it when winter comes. When the first cold days arrive, there may be a shortage of trucks to deliver coal. Deliveries may be planned in advance, and your turn might not come until it is too late.

Jan 1, 1942

By W. A. Calhoun

The purpose of this investigation was to develop economical mineral dressing processes for removing objectionable quantities of impurities, such as quartz and pyrite, from refractory clay deposits in east central Missouri. The presence of excessive quartz in these clays causes crazing. Pyrite causes bloating and unsightly dark blobs on the surface of fired refractory brick. The iron concentration in the proper state of oxidation may also act as nucleation centers for carbon crystal growth which can result in bursting of the refractory. Numerous deposits, representing a very large tonnage, have been examined and prospected by various refractories companies and found to contain impurities in objectionable quantities. Upgrading these clays would greatly extend our reserves of high-quality refractory clays. Wet-tabling and wet-cyclone concentration were found to be effective for removal of impurities from clays. Of the two methods, wet-cyclone concentra¬tion would be cheaper and more effective. Although wet-tabling improved the refractory properties of each clay, beneficiation by wet-cyclone produced clays of superior quality. Clay recoveries by wet-cycloning ranged from 56.1 to 81.8 percent of the weight of the crude samples, and the beneficiated clays contained from 71.9 to 94.4 percent of the total alumina. The pyrometric cone equivalent (PCE) was increased from 1 to 3 cones by wet-cycloning. The beneficiated clays also met the reheat shrinkage requirements on refiring to 1,400° C. Missouri is one of the major domestic sources of fare clay. In addition to deposits of high-grade refractory clays, there arc many deposits that contain small percentages of impurities, which render the clays unfit for the production of high-heat-duty firebrick. Development of methods to beneficiate these submarginal clays to usable materials would greatly increase commercial fire clay resources.

Jan 1, 1961

By M. Clair Smith

This report is one of a series being prepared by the Bureau of Mines on exploration, development, mining methods, and costs at various open-pit mines in the United States. These reports have been prepared in cooperation with various mining companies. A similar program, conducted from 1928 to 1939, was generally conceded to have contributed to improving the efficiency of mining operations. The purpose of these reports is to promote development and conservation of our mineral resources by disseminating technological information on mining methods and practices. This report describes exploration, development, equipment, and mining by open-pit methods of the remainder of an ore body that had been previously worked by underground methods. The Tripp pit of the Consolidated Coppermines Corp. is located at Kimberly, Nev., a small mining company town having an elevation of 7,250 feet, 9 miles by road west of Ely, Nev. (fig. 1). The pit extends over the area formerly mined by underground methods from the Morris and Brooks shafts.

Jan 1, 1962

By Paul Averitt

The coal-bearing rocks in Iowa occur in an arcuate belt across the central and southern parts of the State (fig. 1) at the northern end of the Western Interior coal field. Coal beds of minable thickness are sporadic throughout this area and are mined principally in the three districts indicated by dark shading on the index map, although coal occurs also in the areas indicated by light shading. The coal is mostly of high-volatile C bituminous rank in all parts of the State. SURFACE FEATURES The coal-bearing rocks in Iowa are concealed for the most part by a covering of glacial drift ranging in thickness from a few feet to several hundred feet. This covering has been dissected to form a gently rolling upland, rising from an elevation of 466 feet at the mouth of the Des Moines River to about 1,200 feet in Calhoun County in the central part of the State. The local relief, however, rarely exceeds 150 to 200 feet.

Jan 1, 1949

By J. A. Ruppert, P. M. Sullivan

A study was made of filtration techniques for recovering the major part of the tin contained in iron - tin alloys known as hardhead . Special smallscale filtering apparatus and a three - stage cyclic process were developed . Eighty- seven percent of the tin contained in an alloy of 82 percent tin and 17 percent iron was recovered as pure metal by pressing at 975° C followed by a second pressing at 800 ° C and a final filtering at 250 ° C. Small amounts of Sb , Cu , and Fe impurities were removed by adding Al to the molten product and performing another filtration at 250 ° C.

Jan 1, 1964