Search Documents

By W. H. Ode

Because trade increased among various nations after World War II, the Coal Committee of the Economic Commission for Europe established a Classification Working Party in 1949 to develop an International system for classifying coal. Although national classification systems existed, they had been developed in accordance with characteristics of domestic coals without reference to coals of other countries. Terms for describing similar or identical coals differed in each nation. This caused confusion in evaluating coals shipped in international trade and also hampered exchange of technical information on problems of coal utilization. Experts4/ participating in the classification project early in their work agreed that two systems should be formulated, one for the higher rank coals or so-called "hard" coals in European terminology and the other one for the lower rank coals, the latter designated mainly as brown coals and lignites in the various countries. Rank refers to the degree of metamorphism (progressive alteration) in the natural coalification series from lignite and brown coal to anthracite. The system for classification of hard coals was published late in 1956 as a document of the United Nations.5/ Results of a study for applying this system to American coals were published in 1958.6/

Jan 1, 1960

By John R. McWilliams

This is one of a series of reports being published by the Bureau of Mines on mining methods and costs at various mines throughout the United States. Including the Holden mine in this series is particularly appropriate at this time. The mine was operated on a low-cost, large-scale production basis to compensate for low-grade ore. Even with the best conditions and the most efficient methods, the margin of profit was small. Under the present situation of rising costs and lowering metal prices, the profit margin vanished. On June 28, 1957, the mine operations ceased; therefore, this report can review the entire life span of the mine.

Jan 1, 1958

By L. B. Berger

In this investigation, the ampoule type of carbon-monoxide (CO) detector which is manufactured under license of U. S. Patent 1,644,014 (October 4, 1927) was tested for sensitivity and reliability. This detector was devised primarily for examining the air of manholes and sewers for possible dangerous contamination with CO before workmen enter these places, but due to the simplicity of the device it may have a more general usage for examination of atmospheres which are known or suspected, to be contaminated with CO. Some of the suggested uses are the examination of the air in garages, tunnels, mines, around blast furnaces, gas plants, and in the home.

Jan 1, 1930

By L. L. Rethi

The U.S. Bureau of Mines summarized injury data for independent contractor employees working at all locations of coal and metal-nonmetal mines from 1983 through 1990. During the eight years, the greatest contrast in degree of injury between independent contractor and operator employees was in fatalities. From 1983 through 1990, there were 132 independent contractor employee fatalities in the mining industry. In 1988 though, independent contractor employees accounted for nearly one-fourth of all mining fatalities. The fatality incidence rates of independent contractors were consistently higher than those of operators during the eight years. For instance, in 1990, the contractors' rate was twice that of operator employees in coalmining and nearly five times that of operators in metal-nonmetal mining. Three other salient facts highlight the independent contractor employees' fatality injury data during these years. First, 82% of the independent contractor employee fatalities occurred at surface locations. Second, two job classifications?truck driver and equipment operator?represented 37% of the fatalities throughout the 8-year period. And finally, four accident classifications?powered haulage, slips and falls, machinery, and electrical?accounted for 71% of all independent contractor employee fatalities.

Jan 1, 1993

By Ann G. Kim

Studies on the initiation and propagation of mine fires have dealt almost exclusively with coal. It has been assumed that the self-heating potential of carbonaceous shales and coal wastes is relatively low. However, in abandoned coal mines and waste banks, initiation and propagation of fires may be strongly dependent on the self-heating tendency of these materials. The purpose of this study was to compare the self-heating probability of carbonaceous shales and coal wastes to that of coals. This study utilized a modified differential thermal analysis method, in which the combustion furnace temperature was the reference to which the sample temperature was compared. Based on the distribution of the maximum temperature differential and the sample heating rate, a self-heating probability value (SHPV) was calculated that corresponded to observed self-heating behavior. In this study, several of the carbonaceous shales and one coal waste had relatively high SHPV. The SHPV did not correspond directly to heating values or to differences in sulfur concentration.

Jan 1, 2010

By J. R. Thoenen

In the summer of 1937 the authors began a series of time studies of the various processes employed in' the production of crashed stone. These studies, made at quarries situated in the eastern and southeastern parts of the United States, have not been completed, but to make results available to the industry as early as possible, it was decided to publish summarizes of the studies made to January 1, 1939, as a series of progress reports. The first of these dealt with power-shovel loading and was issued as Report of Investigations 3461 in September 1939. The second, issued in September 1939 as Report of Investigations 3467, dealt with quarry haulage. The present report discusses analyses of time studies of primary drilling a t the same group of quarries. OBJECT OF STUDY Pressure of business problems frequently requires the entire attention of quarry management, and in consequence internal plant economies often are neglected. Also, operating officials absorbed in their local problems are prone to overlook possible economies that would attract attention immediately were they critically examining another plant. The authors felt that technical studies at a number of plants, made by impartial engineers, might disclose opportunities to reduce costs or improve efficiency in internal plant processes.

Jan 1, 1940

By Manuel Gomez

A computerized moving average technique was developed to interpolate coal seam characteristics between sample points. The interpolative method coupled with multivariate regression analysis and simulation procedures was used to forecast coal properties not readily obtained from an analysis of drill core samples. Coal property forecasts were of two kinds: (1) specific mine property forecasts that are suitable for mine product control and yield a good approximation of the local variation along both the vertical and horizontal axes of the seam, and (2) regional estimates where much of the local seam variation is smoothed out, but the general trends are maintained. Forecasts of the volatile matter, ash, total sulfur, and the heating value for part of the Pittsburgh seam located in Ohio, Pennsylvania, and West Virginia were in good agreement with independent evaluation data. Spatial configuration for preparation characteristics, particularly, the effect of crushing on sulfur release, low-and high-temperature carbonization properties, the Hardgrove grindability index, the coal hardness index, gasification variables, and hydrogenation factors were constructed for the same area of the Pittsburgh seam. These forecasts may be developed from drill core data collected in the exploration phase of mining. The results, which may take the form of a series of maps, are useful to mining, chemical, and combustion engineers, to economists and mine managers, as well as to coal users for mine design, economic analyses, energy forecasts, utilization studies, mine product control, and environmental control and programming.

Jan 1, 1974

By T. M. Garland

A nomographical approach is proposed as a fast, easy-to-use, and reason- ably accurate method for estimating expected discounted cash flow (DCF) rate of return and payout time for onshore development drilling and oil production. All costs pertaining to drilling, completing, and equipping development wells, annual expenses of operation, maintenance, and taxes incurred in producing properties, and crude oil prices were considered in developing the nomographs. This report briefly outlines the origin, derivation, and use of the nomographs.

Jan 1, 1973

By F. L. Wideman

This report describes a computer program that is used for the calculation of the coordinates and elevations of subsidence survey pins located by intersection. This program was developed for the Federal Bureau of Mines by the Numerical Analysis Laboratory, University of Arizona. These calculations, although relatively simple, are both tedious and time-consuming when computed with a desk calculator and trigonometric tables. In this survey, a large number of pins were surveyed repeatedly, and it was evident that both time and money could be saved by using a digital computer.

Jan 1, 1962

By F. W. Wood

A program of research was conducted by the Bureau of Mines to investigate anomalies in electrical-discharge behavior during consumable-electrode arc melting of titanium and to study the effects of these irregularities on arc-furnace explosions. A major effort was devoted to an experimental survey of arc behavior and a qualitative definition of discharge phenomena.3/ An important conclusion was that the "glow" of industrial arc-melting terminology is not a glow discharge but a skittering arc in a displaced position. The conditions that permit displaced skittering were tentatively defined. The displaced skittering arcs tended to damage melting crucibles in two ways, and details of possible mechanisms leading to crucible rupture and explosive reactions have been proposed accordingly. However, no acceptable means of preventing crucible damage was discovered.

Jan 1, 1961

By Andrew A. Cochran

Laboratory-scale research was conducted by the Bureau of Mines to develop a new process for treating electroplating and other wastes. Various acid and alkaline cyanide wastes were combined under controlled conditions to neutralize the wastes and to almost completely precipitate the metals and cyanides. The metals were subsequently recovered for recycling; the cyanides can also be easily recycled. The process was successfully used to treat the major types of electroplating and etching wastes, containing Cd, Cr, Cu, Ni, and Zn, and to treat both concentrated and dilute wastes. The economic aspects of treating concentrated electroplating, etching, and anodizing wastes are especially attractive because of the low cost of mixing two wastes, the high value of the recovered metals, and the simplicity of the recovery procedures. The filtrates from the waste-plus-waste step were relatively harmless compared with the original wastes and met Public Health Service standards for free cyanide content. Free cyanide ions were not detected in most of the filtrates; the limit of detection was 0.03 ppm. Only small amounts of HCN were produced during the neutralization; the HCN was collected and neutralized.

Jan 1, 1974

By M. W. Pullen

It is recognized that the determination of electrical resistivity of the earth within a given area may furnish information concerning the location of certain mineralized strata of economic importance. Present knowledge of the electrical resistivity of the various rock formations is almost nil, and the geophysicist who is detailed to make a survey of an area without any data as to the relative resistivity of the underlying rocks is greatly handicapped. Such surveys are usually made within areas known to contain mineral deposits to aid in locating desirable points for drilling. Usually these areas have been prospected by diamond drilling, and drill cores of the various rocks and ores are usually obtainable. Were it possible to make resistivity tests in a laboratory of the drill cores or from pieces of the rocks and ore within an area before attempting a field survey, this would indicate not only the advisability for such a survey but would aid considerably in the interpretation of the results of such a survey. To be of most value a definite method should be used for all such tests, and as yet such a method has not been established.

Jan 1, 1929

By N. H. Coates

As part of a joint program of the U.S. Atomic Energy Commission and the Federal Bureau of Mines for using nuclear energy to supply process heat, the Bureau designed and constructed a pilot-scale simulated nuclear reactor system. Although workable components were developed,5 the simulated nuclear reactor could not be operated continuously at its design conditions of 2,500°F. and 250 p.s.i.g. because the refractory materials used for insulation deteriorated. Replacement of these materials with porous carbon permitted sustained operation at design conditions, and a 1,000-hour demonstration run was completed successfully. No serious operating difficulties developed during the test. Leakage of helium after 1,000 hours was only 3 to 4 std. c.f.h. Inspection after the run revealed no damage to any of the components. Including earlier runs during previous research5 the system has been operated about 4,000 hours, of which 1,120 hours have been at 2,500° F. or higher. The helium-recycle compressor performed satisfactorily with no main¬tenance whatever for 2,445 hours, with about 2,000 hours at 900° to 1,000° F.

Jan 1, 1961

Engineering controls for overburden drilling include dry dust collection systems, wet dust suppression systems, and enclosed cabs [Zimmer and Lueck 1986; Volkwein et al. 1979]. Proper maintenance of the dust suppression system is critically important for drills using dry dust suppression methods. Failure to rigorously maintain these systems will result in inadequate dust control. Acute silicosis has been reported in miners operating equipment that relies on dry dust suppression [NOSH 1992].

Jan 1, 1997

By E. O. Wagner, Manuel Gomez, W. S. Landers

The Bureau of Mines studied coking rates of a special Columbia - Geneva six - coal blend to establish the effect of the coking rate on coke properties . The tests were conducted in a 500 - lb , 14 - in experimental slot oven at essentially constant conditions of blend composition , size distribution , surface moisture content , and bulk density . The coking rate was varied as a function of oven flue temperature . Coking rates within the range of 0.56 to 1.35 in/hr were achieved . Increase in the coking rate decreased the size of the coke . The stability factor of the coke showed no significant change with coking rate until coking rates greater than 1.0 in/hr were reached , after which a decrease in the stability factor was observed . The apparent specific gravity increased to a maximum value at coking rates approaching 1.1 in/hr and decreased sharply with further increase in the coking rate . Coke parameters correlated well with the coking rate .

Jan 1, 1963

By F. D. Wang

The Bureau of Mines has developed a computer program for evaluating pit slope stability by the finite element stress analysis and limiting equilibrium method. The program includes the finite element method of stress analysis using triangular elements, finite-element model mesh generation, plotting of the model mesh and stress contours, calculation of a factor of safety along a circular or a plane failure surface, and location of a critical circular failure surface. Instructions for preparation of input data, an example problem, and the program listing are presented.

Jan 1, 1972

By Albert L. Toenges, Theodore R. Jolley

"INTRODUCTION The construction of frame houses (fig. 1) in recent years instead of the conventional sod hut (igloo) (fig. 2) by the Eskimos in the villages along the Arctic Ocean has increased the demand for fuel in these villages. The frame houses, which are not insulated against extreme cold and are difficult to heat, are equipped with Goal stoves. The well-insulated sod huts were heated comfortably with whale-oil stoves. In some years whaling is Door, consequently there is a demand for solid fuel.The Eskimo villages usually are on the sand spits at the mouths of rivers and points of land near the best fishing and hunting grounds. These narrow necks of land usually are sand bars that are not underlain with coal, and coal must be transported to the villages. Lack of development of coal deposits in the Arctic has made it necessary to import coal from the States, generally from 'Washington, to supply these villages. This coal is imported by boat and is received once a year. Its cost is, high, and development of coal deposits in the Arctic to supply these native villages should result in a considerable saving to the Government-operated schools and hospitals as well as to the natives.Early traders attempted to establish coaling stations in the Arctic, and the Eskimos generally know where the coal deposits are situated. A. reconnaissance of a number of deposits in the Arctic was made in the summer of 1946 by engineers of the Coal Division, Fuels and Explosives Branch, Bureau of Mines, and this report describes the areas investigated and suggests plans for the development of some of these deposits."

Dec 1, 1947

By H. C. Hamontre

[The Bureau of Mines well-bore caliper was designed to provide an instrument that could be operated through 2-inch tubing, which 'a used particularly in many input wells on water-flooding projects of eastern, Kansas and northeastern Oklahoma. It should find wide application elsewhere under many other conditions where it has not been possible previously to make caliper logs with the larger probes used on other instruments. The caliper has three additional advantages over other instruments of this type: (1) It measures 4 radii (up to 18 inches) 90° apart with an accuracy of ± 1/4 inch; (2) the measuring arms can be opened and closed at will by remote control; and (3) it is run and operated on a single-conductor, armored electric cable (Amergraph, type 1-H-0). The caliper probe is 1-3/4 inches in diameter and approximately 6 feet in length. The electrical control and measuring circuits are encased in a stainless-steel tubular case. Measuring arms, made of 5/16-inch aluminum tubing, are attached near the lower end of the instrument. Distances the arms are extended are indicated t the surface by a meter calibrated to read directly in inches. Depths at which the radii measurements are taken are indicated by a wireline depth indicator on the cable-reeling. The instrument is not affected by pressure or temperature, it can be run open hole or under pressure through a lubricator. This paper describes and illustrates the instrument and outlines the operating procedures. A bibliography at the end of the report gives references to articles and patents on the development and use of other well-bore calipers.]

Jan 1, 1954

By Deborah A. Kramer

An economic and technical evaluation of a proposed process to recover alumina by leaching calcined kaolinitic clay with sulfurous acid is presented in this Bureau of Mines report. After the insoluble portion of the clay has been removed by leaching, monobasic aluminum sulfite is precipitated from the pregnant leach solution by partial hydrothermal decomposition. Further heating completes the decomposition to an impure alumina hydrate. This intermediate is purified in a modified Bayer process, which includes dissolving the alumina hydrate in a caustic solution at high temperature and pressure, then decreasing the temperature and pressure to precipitate alumina trihydrate. Calcining the trihydrate produces the alumina product. A cost estimate was prepared for a plant producing 1,000 tons of alumina per day, 350 d/yr. The estimated operating cost is approximately $475 per ton of alumina. This is substantially higher than a comparable estimated operating cost for the Bayer process of $250 per ton of alumina. The proposed process does not appear economically attractive, even as a method to modify a current Bayer processing plant to use a kaolinitic clay feed. High capital costs and high energy requirements make the process prohibitively expensive.

Jan 1, 1983

By J. R. Welty

High-temperature thermodynamic data have, in recent years, become increasingly important for the extractive metallurgist. The extraction of metals from their ores previously was based on trial and error methods, involving hours of testing and often costly equipment fabrication. Using thermodynamic data it is frequently possible to predict the feasibility of a proposed metallurgical process as well as the optimum operating conditions for the process with reasonable accuracy. Such predictions can save consider-able tim~ and expense. Widespread use of thermodynamic analyses has been handicapped by lack of dependable experimental data. Investigators, notably K. K. Kelley (4)4. have devoted many years to determining and compiling such data. These investigators, although prolific in their production of thermodynamic values, have been unable to meet all the needs of industry and other branches of science. This becomes obvious when one considers the aeronautical and nuclear fields, in which previously unimportant, therefore uninvestigated, substances have become of prime importance.

Jan 1, 1962