Search Documents

By C. B. Manula, R. L. Sanford, R. A. Rivell

PART I. DATA INPUT FOR THE OPERATING PROTOTYPE [To run the Rail Haulage Model independent of the Production Sub-system, remove the production data from card type four through the blank card following END DATA on page B18 and change the fourth data element under ADDITIONAL DATA from 1 To 0.]

Jan 1, 1974

By F. N. Kissell

The applicability of the "direct method" for determining the methane content of virgin coalbeds was tested. Preliminary results indicate that the direct method, when applied to exploration cores, can be successfully used to estimate coalbed gas content and also approximately predict the total gas emission from a prospective mine located in the coalbed at the exploration site.

Jan 1, 1973

By W. B. Berwald, T. W. Johnson

"The United States Bureau of Mines, in cooperation with the Natural Gas Department of the American Gas Association, has been studying actively for the past several years the flow of natural as through high-pressure pipe lines. 4 This report deals with that part of the study involving the design of pipe-line systems consisting of lines laid parallel to each other. The lines are referred to as the original line and the parallel line. The paralleling lire may or may not extend the entire length &f the original line; however, the parallel line is connected at its two ends to the original line.As a result of the large expansion of the natural-gas industry almost all markets within economic distance, from the developed as fields have at least one pipe line supplying them with natural gas. Small increases in the consumers' demand for natural-gas can be met usually by increasing operating pressures, but any marked increase in demand necessitates paralleling sections of the existing systems. It is believed that to a large extent future expansion in the natural—gas industry will consist of paralleling the present lines. The several formulas given in this report have been developed to aid in the design of such systems. Curves and tables were prepared from these formulas to simplify the calculations materially and to facilitate determination of the sizes of pine to be used in paralleling various diameter lines to give the most economical design. The formulas are presented without detailed derivations, as a complete report on the flow of natural gas through pipe lines is being prepared which will contain the derivations of these formulas. Examples included here show the detail of application of the several formulas to problems of design of parallel lines."

Jun 1, 1934

By William S. Sanner

A demonstrated reserve base (DRB) of bituminous coal suitable for cokemaking has been estimated based on the latest published information on U.S. coal reserves. Bureau of Mines analyses of raw coalbed samples were used to classify the coals as low-, medium-, and high-volatile bituminous and grade them as premium, marginal, and latent coking coals. Coal rank was used as the basis for identifying coking coals, and ash and sulfur content were used to determine coking coal grade. The demonstrated reserve base of coking coal for the entire United States is 162.67 billion tons. However, only 18.96 billion tons are premium (metallurgical) grade, and between 80 and 99 percent occurs in the Eastern States. The demonstrated reserve base of marginal-grade coking coal is 31.3 billion tons; more than half the marginal reserve base is in the Eastern States, and most of the medium- and low-volatile marginal coals are in the Eastern States. The Eastern and Midwestern States contain most of the latent-grade DRB of 112.4 billion tons; most (106.6 billion tons) is high-volatile coal, and 98 percent of the medium- and low-volatile latent coals occur in the Eastern States. Based on the worst assumption, which assumes that only premium-grade coals are used for cokemaking, the DRB for high-volatile coal would suffice for 127 years, the medium-volatile coal for 80 years, and the low-volatile coal for 83 years.

Jan 1, 1979

By James R. Boyle

The mining methods and practices used at the Young zinc mine, American Zinc Co. of Tennessee, have resulted in a low-cost, high-yield operation. Zinc ore (sphalerite) occurs in limestone-dolomite beds of the Kingsport Formation and is mined by modified room and pillar method. Utilizing trackless mining equipment which incorporates a high degree of flexibility, this operation has had a steady increase in productivity.

Jan 1, 1965

These proceedings consist of papers presented at a Bureau of Mines Technology Transfer Seminar in September 1981 for the purpose of disseminating recent advances in mining technology in the area of premining research. The introduction and descriptive papers discuss techniques and instrumentation used in premining research for metal and nonmetal mining and shaft design and borehole control for premine planning.

Jan 1, 1982

By E. J. Gleim

The importance of "good voltage,? especially for direct-current systems in coal mines, is not always fully appreciated. From the practical 4 aspect there are three viewpoints from which low voltage may be considered, namely: (a) its effect upon operation of electrical equipment, (b) its effect upon cost of maintenance and power, and (c) its effect upon safety in the mine. The design of electrical motor-driven equipment usually is based upon a given or assumed constant value for the voltage of the system; consequently, when there is an appreciable drop below this value, unsatisfactory operation is likely to follow. In the case of shaker conveyors, for example, one manufacturer has pointed out that these conveyors must be operated at a certain definite speed if maximum output is to be secured. As shunt motors are used in the conveyor drives, either a rise or fall in voltage will produce corresponding changes in speed and thus seriously affect the efficiency of the conveyor. The introduction of automatic control for mine equipment has been greatly retarded because the relays, contactors, and other special devices required have failed to function properly when attempt was made to operate them on systems subject to variable and low-voltage conditions.

Jan 1, 1937

By Robert H. Dickson

This paper describing the mining practices at the Verde Central mine at Jerome, Ariz., is one of a series being prepared by the United States Bureau of Mines on mining practices, methods and costs in various mining districts of the United States. ACKNOWLEDMENTS The costs contained in this paper were prepared by R. J, Huddleston, chief clerk, Verde Central Mines, Inc.

Jan 1, 1931

By Marvin L. Whisman

A radiotracer technique developed by the Bureau of Mines extends to the parts-per-billion range the sensitivity for determining contributors of deposits formed in stored and thermally stressed jet fuels. The method depends upon measuring radioactivity associated with thermally induced deposits from fuels containing one labeled compound. The technique was applied to 88 test blends, representing 12 fuels and nine carbon-l4 labeled fuel constituents or fuel additives, or both. Data from results of these tests are included in this report. With this radiotracer technique, the contribution of fuel components and additives to thermally induced deposits in a variety of fuel environments was estimated before and after storage.

Jan 1, 1969

By K-H. Frohne

This report presents a study of the Cooper sand of the Fork Run pool of Warren and McKean Counties, Pa., and a prediction of the secondary oil recovery by gasflooding the reservoir. A computer program employing a modification of the Craig, Geffen, and Morse secondary recovery calculation was used to make the gas flood performance forecast and is presented in the appendix. The Cooper sand reservoir in the Fork Run pool lies at a depth of about 1,900 feet and covers an area 1/2 mile wide by 2-1/4 miles long. Original oil in place is estimated to have been 8,266,000 STB. The primary recovery mechanism is solution gas drive, and ultimate primary recovery may reach 20 percent over a well life of 90 years. Two computer predictions were made for gas flooding the Cooper reservoir. The first was for a 25-acre pilot five-spot utilizing existing wells, but project economics were poor since only 25 percent of injection gas is utilized for pilot oil recovery. Recovery was 71,000 STB, or 22 percent of oil in place at flood initiation, but required 25,700 scf gas injected per STB of oil recovered. In the second prediction, pilot area performance was projected for the entire Fork Run pool, and economics became good. Recovery was 1,753,000 STB from 25 five-spots after the injection of only 6,400 scf per STB of oil recovered.

Jan 1, 1969

By Thomas W. Camm

The U.S. Bureau of Mines has developed a system for estimating mining and processing costs as a function of process feed rate with the objective of applying this system to abandoned mine tailings and to evaluate the benefits, if any, of metal recovery. Cost analysis was applied to the mine wastes of Smelterville Flats: an extensive area of mine tailings in the Bunker Hill Superfund Site with high concentrations of lead, zinc, and other sulfide minerals. Results from previous site characterization and metallurgical processing studies were used as the input for the cost analysis. This analysis indicated that processing this site at an optimum production rate of 3,500 short tons per day (st/d) could generate a positive cash flow.

Jan 1, 1993

By Peter Swanson, Collin Stewart, Wendell Koontz

A seismic monitoring network has recently been installed in the North Fork Valley coal mining region of western Colorado as part of a NIOSH mine safety technology transfer project with two longwall coal mine operators. Data recorded with this network will be used to characterize mining related and natural seismic activity in the vicinity of the mines and examine potential hazards due to ground shaking near critical structures such as impoundment dams, reservoirs, and steep slopes. Ten triaxial strong-motion accelerometers have been installed on the surface to form the core of a network that covers approximately 250 square kilometers (100 sq. miles) of rugged canyon-mesa terrain. Spread-spectrum radio networks are used to telemeter continuous streams of seismic waveform data to a central location where they are converted to IP data streams and ported to the Internet for processing, archiving, and analysis.

By W. T. Millar

"INTRODUCTION The purpose of the Star Lake project was to investigate, by geophysical surveying and diamond drilling, the magnetite deposits in the northwestern Adirondacks, the ultimate objective being to increase iron production in eastern United States,ACKNOWLEDGMENTSIn its program of investigating mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to the national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclu-sion. The Mining Branch, Lowell B. ""Moon, chief; conducts preliminary examinations, performs the actual investigative work, aid prepares the final report. The Metallurgical Branch, Oliver C. Ralston, chief, analyzes samples and performs beneficiation tests.The chemical and spectrographic analyses included in this report were performed at the Eastern Experiment Station of the Bureau of Lines at College Park, Md., under the general supervision of J. B. Zadra, chief, College Park Division, Metallurgical Branch, and under the immediate direction of Dr. Alton. Gobriel in charge of the laboratory service unit.The mineral exploration was under the general supervision successively of John D. Bardill, district engineer, and McHenry Mosier, chief, College Park Division, Mining Branch. The work was done under the immediate supervision successively of J. P. Ryan, N. A. Eilertsen, and W. T. Millar, project engineers."

Sep 1, 1947

By S. M. Runke

[The coarse-grained granitic pegmatities of the United States have long been a source of many important industrial minerals, because of this, they have been studied intensively by geologists, mining engineers, end metallurgists. These studies have amassed a rather astounding array of published and unpublished information. Correlation of geological studies between individual pegmatites, as well as between major districts, has brought fort come semblance of order to the knowledge of the structure and mineralogical composition of those highly complex and irregular deposits, making it possible to classify certain pegmatites and pegmatitic zones into several grouts of associated minerals, based upon the presence or absence of the minor minerals of beryllium and lithium. This classification or trouping of minerals, with the methods that have been developed for recovering certain of these minerals, possible a systematic approach to the winning of many of the industrially important minerals from pegmatite rock by u single integrated process.]

Jan 1, 1952

By M. Dattilo

The U.S. Bureau of Mines has been conducting research on the use of waste-derived zinc as a partial replacement for pure zinc in the electrogalvanizing process. The end product of this process is automotive sheet, which has enhanced cosmetic protection over previously used cold-rolled (CR) steel. In this study, primer-coated specimens of CR and electrogalvanized (EG) steel were subjected to the on-vehicle environment and monitored periodically by electrochemical impedance spectroscopy (EIS) during immersion in 1M NaCI solution. The results of these tests were compared with immersion-only conditions. Scanning electron microscope (SEM) and energy-dispersive X-ray (EDX) techniques were also used to evaluate the corrosion processes and compare them with atmospheric exposure specimens. EIS was found to measure the corrosion associated with on-vehicle exposure, thus providing an excellent screening technique for evaluation of the performance of EG automotive sheet steel.

Jan 1, 1990

This report describes the development of training materials for the operators of underground mining equipment in the underground metal and nonmetal mining industry. The objective was to determine the effectiveness and acceptability of these training materials and to provide the validated training materials to the industry. Ten modules were developed, based on industry need according to accident frequency, accident severity and exposure to the equipment. The final modules were an average of 20 minutes in length and used slides with synchronized narration on cassette tapes. Testing materials are included for use by the mines.

Jan 1, 1984

By Richard H. Spencer, Warren G. Bender

Since the passage of the Coal Mine Health and Safety Act of 1969, the Bureau of Mines has made many advances in mine communications. These efforts have resulted in the following developments and demonstrations: • Surface-to-surface electromagnetic transmission of baseband voice signals through overburdens as deep as 600 feet. This transmission was achieved with equipment from the Interim Mine Rescue and Survival System Program, and demonstrated that baseband voice communications could be obtained through these overburdens in the absence of mine-generated noise; that is, when the mine power system was shut off. However, during mine operational conditions, the mine-generated noise proved to be so large that effective baseband voice communications to the desired depths could not be effected. • The development of beacon transmitters for locating trapped miners. This work was again the outgrowth of the Interim Mine Rescue and Survival System. Extensions of this work have led to reliable detection and location of trapped miners to depths of 1000 feet. The system, which makes use of a loop antenna deployed where the trapped miner is located, uses low-duty-cycle, tone-burst transmission. Portable tuned receivers and loop antennas are used on the surface to determine the location of the trapped miner. An extension of this work has led to a call-alert paging system concept, wherein a transmitter, similar to that used in the trapped miner system, is used to audibly and/or visually alert key mine personnel carrying pocket receivers that they are wanted at the nearest mine telephone. In addition, a roof-bolt paging system has been developed, wherein commercial paging and mine carrier phone equipment are used in conjunction with a long-wire "roof bolt" antenna to page individuals and relay to them short voice messages.

Jan 7, 1975

By Michael E. Meadows

The results of tests to determine the .regional applicability of four synthetic unit hydrograph models are presented. The SCS curvilinear (Haan), SCS single triangle, Williams and TVA double triangle unit hydrograph models were tested on 271 events from 38 USDA experimental watersheds in 14 physiographic provinces. Though inconclusive due to the limited number of events analyzed, the results indicated a regional tendency for each model, with the SCS curvilinear unit hydrograph method generally performing best overall. It outperformed the SCS single triangle by predicting better shape; they differed less than 2 percent in time of peak and peak rate predictions. The Williams model performed well at Oxford, Mississippi and Coshocton, Ohio, which suggests it may be applicable to surface mined lands within the Northern and Central Appalachian Plateau and Texas coal producing regions. The TVA model is applicable to the Appalachian Plateau, specifically the Cumberland Plateau. A second test using only the SCS curvilinear unit hydrograph on 11 small watersheds and 50 events was conducted to investigate the effect of the excesss rainfall pattern on simulation results. A Green and Ampt infiltration model was coupled with the SCS unit hydrograph model to determine if peak rate and timing errors noted in the regional test could be minimized with an alternate to the SCS curve number model for determining infiltration losses. The results confirm the curve number model is the better approach to determining the excess rainfall pattern for unit hydrograph simulation.

Jan 1, 1983

By Andrew K. C. Wong

Hydraulic transport has been considered as one of the most economical methods in transferring granular materials over relatively long distances. In the natural world, it is used to transport basic material required for the support of life; in industry, it is a method widely adopted for handling materials. But the phenomena of hydraulic transport has not yet been thoroughly understood. As most of them are conditioned by a number of hydraulic and mechanical parameters, of which the basic relationships are not fully known, the traditional approach in relating these parameters to the energy requirement is purely empirical in nature. Empirical formulas, such as that proposed by Durand, (1) only give satisfactory results over a selected range of (particle size)/(pipe diameter) ratios and slurry concentration. When the case is more complicated or when new situations arise, the empirical formulas fail to give good predictory results. In fact, most of these formulas are based upon dimensional analysis, where the underlying physical interaction is not explicitly considered. Apart from the loosely related, non-dimensional groups incorporated in the formulas, there is practically no analytical means for modifying the formula so as to enable it to cope with more complex real physical situations. Although it seems quite remote that a complete rigorous solution to this highly complex problem could be generated in the near future, it is generally recognized (2, 3) that research in this area should be directed to more comprehensive studies of the obscure phenomena. In fact, there are a good number of very basic problems such as the effects of gradation and concentration of particles upon

Jan 1, 1972

By Thomas C. Miller, Rudolph Sporcic

A relatively simple and inexpensive encapsulated hydraulic device has been developed by the Bureau of Mines to facilitate study of coal bumps , and to measure pressure changes in a coalbed as it is subjected to roof loading during mining . Construction of the device and application techniques are described . Preliminary feasibility tests in the laboratory and field indicate that the device responds satisfactorily to pressure changes in coal created by roof loading .

Jan 1, 1964