Search Documents

By J. D. Brown

The electron optics, vacuum system, and sample stage assembly for the Bureau of Mines? electron probe X-ray spectrograph were purchased. Four scanning curved-crystal spectrometers, two reflection- and two transmission-type, were designed and constructed by the authors. The reflection spectrometers are placed in a vacuum chamber for measurement of long-wave-length X-radiation. Detection, pulse-amplitude discrimination, and recording circuits are provided for the simultaneous measurement of four X-ray spectral lines. Minimum spot size is approximately 2 microns in diameter at 30 kilovolts and a sample-to-ground current of 5 x 10-8 ampere. At this voltage and current the limit of detection with reflection spectrometers is less than 0.05 weight-percent for most elements. The limit of detection for elements determined by transmission-type spectrometers, evaluated at 35 kilovolts and 5 x 10-8 ampere, is approximately 0.1 weight--percent for all elements having excitation voltages below 20 kilovolts. In general, reflection spectrometers exhibited satisfactory but poorer resolution than the transmission type, resolution of the spectrometers being limited primarily by crystal imperfections, with greater mosaic structure being introduced by the grinding process for the reflection crystals. Several applications of the electron probe X-ray spectrograph are described. Analysis of a uranium-steel is discussed in detail to illustrate calculation of composition from measured X-ray intensities.

Jan 1, 1962

By Robert M. Doerr

Isothermal oxidation kinetics were determined for three grades of Ni and for 99.99 percent Co in Ca and in air from 800° to 1,200° C. The oxidation reactions followed approximately the parabolic rate law. For 99.99 percent Ni in 02 at 1,200° C, the parabolic rate constant was 2 mg cm-2 hr-2. For 99.99 percent Co in dry air, the constant ranged from 1 mg cm-2 hr-2 at 800° C to 18 mg cm-2 hr-2 at 1,200° C; for 99.99 percent Co in 02 the constant was 2 mg cm -2 hr-2 at 800° C and 10 mg cm-2 hr-2 at 1,000° C. For 99 percent Ni in dry air, the constant ranged from 0.2 mg cm 2 hr-2 at 800° C to 3 mg cm 2 hr-2 at 1,200° C. By X-ray diffraction measurements, only divalent oxides were found in the scales. Volumetric and quartz-helix gravimetric methods were used. The volumetric apparatus was designed to permit less stringent restrictions on the corrosion specimens; it was also more convenient to use. The agreement between the weight gain determined gravimetrically and the 02 consumption determined volumetrically was not good enough for direct comparison of gravimetric and volumetric results.

Jan 1, 1963

By Charles White Merrill

Silver consumption in the arts and industries of the United States during 1930 and 1931 has remained remarkably near the high level established in 1929. Undoubtedly the sharp drop in the price of silver has been an important factor in supporting consumption, but silver's peculiar properties and uses probably have been an even more compelling reason for its sustained utilization. In its most important use - sterling silverware - it seemingly has most serious competition, but well established tradition protects the demand for sterling ware and the law forbids the term "sterling" to be applied to any material not containing at least 92.5 per cent silver. The photographic industry is dependent upon properties of certain silver salts possessed by no other material. Consequently silver is indispensable to all photography, including the huge motion picture industry. Other uses for silver could be listed which, because of special features, likewise have tended to maintain the consumption of silver in the arts and industries of the United States. The figures which this report makes available for the first time are the detailed silver consumption figures for the arts and industries of the United States for 1930 and 1931. These figures have been tabulated with the previously published(3) figures for 1928 and 1929 thus presenting a 4-year statistical record of silver consumption. All quantities are given in troy ounces, 1,000 fine.

Jan 1, 1932

By S. H. Brooks

"IntroductionThis preliminary report deals with the effect of oxygen pressure on the ignition temperature and combustibility of oils, it is the third of a series which will present the results of an investigation being made by the Bureau of Mines, on oxygen-oil explosions. The purpose of this research is to obtain technical data that will serve as a basis for safety precautions general outline of the problem has been given in the first report (Serial 2507).The present experiments have resulted in (1) a method for determining spontaneous ignition points of oils in an atmospheric of oxygen under pressure; and (2) the determination of these ignition temperatures for three typical oils, one being an animal oil (sperm), one a vegetable oil (linseed), and one a mineral oil (""Moiloil A"").These experiments on explosibility of oil were performed in order to discover the general nature of the phenomenon, especially the order of magnitude of the temperature necessary for spontaneous explosion (120°C. and upwards) and the effect of pressure variation (negligible as regards ignition temperature but important in relation to the violence of the explosion). A continuation oftests should provide a basis for selecting the safest lubricants for high pressure compression of gases particularly air and oxygen; and should be of value when devising new specifications for lubricants, both in the government departments and the compressed-gas manufacturing industry."

Dec 1, 1923

By Steven J. Schatzel, William P. Diamond

Coalbed gas content measurements are commonly used in mine safety as well as coalbed methane resource assessment and recovery applications. Gas content determination techniques generally fall into two categories: (1) direct methods which actually measure the volume of gas released from a coal sample sealed into a desorption canister and (2) indirect methods based on empirical correlations, or laboratory derived sorption isotherm gas storage capacity data. Direct gas content determination techniques may be further. subdivided into quick-crushing and extended desorption methods. The quick-crushing methods are primarily used in mine safety applications outside the United States, but have also been used for resource recovery applications. Quick-crushing methods rely on crushing the coal sample soon after collection to release all the desorbable gas, thus significantly shortening the amount of time required for desorption measurements. However, some data useful for resource recovery applications are lost. Extended desorption techniques are most commonly used for resource assessment and recovery applications where information on desorption rates is useful for reservoir modeling, and for fundamental coalbed methane research. Extended desorption methods allow the gases in the coal sample to desorb under controlled laboratory conditions until a defined low desorption rate cutoff point is reached. The sample may then be crushed to measure the amount of gas remaining within the sample. Direct method techniques for gas content measurement are the focus of this paper.

By E. P. Dowding, J. Schlocker, C. H. Fuchsman, R. R. Lloyd, Mahan. W. M., O. C. Garst, W. T. Rawles

"INTRODUCTION The United States, although the leading consumer of chromite, depends almost entirely on imports for its supply. For instance, the consumption during. 1941 amounted to 714,645 long tons, whereas the domestic chromite production, although the highest since 1918, was 12,731 long tons or only 1.78 percent of the domestic consumption. 9/ Domestic production was tremendously, accelerated,after 1941 by war demands; however, only a small proportion of this domestic product was of sufficient quality to be substituted for the high-grade imported chromite demanded for metallurgical purpose. Chromite is used largely for making ferrochromium, an alloy containing 60 to 70 percent chromium which is used in making alloy steels. Peacetime specification for ferrochromium required that it should contain 68 to 69 percent chromium. These specification were lowered to between 60 and 63 percent, chromium in 1941 to permit the use of lower-grade ores. The specifications for metallurgical chromite, used for making ferrochromium, were established first by the Metals Reserve Company at 48 percent Cr203 and a Cr. Fe. ratio of 3 : 1 but later were lowered to 45 percent Cr203 and a Cr : Fe ratio of 2.5 : 1. The ratio of chromium to iron in chromite is important, because the contained iron enters the alloy in making ferrochromium and, although an ore may contain the required 45 percent Cr203, it may contain too much to be suitable for ferrochromium production. The principal sources of domestic chromite are California, Oregon, Montana, and Alaska minor, small, and widely scattered deposits in another dozen States. Without exception, these deposits are low-grade, require beneficiation to produce a commercial product, and are not competitive with imported high-grade ore in normal times. Nevertheless, these deposits form strategic reserve, which must be utilized in periods of national emergency. Recognizing this fact; the Bureau of Mines for many years has undertaken investigations to develop methods of utilizing domestic chromite ores. The problem has been approached from three angles: (1) Mechanical methods of concentration; (2) beneficiation by chemical or metal¬lurgical methods; and (3) production of metallic chromium by electrolysis of solutions prepared from ore or concentrate."

Feb 1, 1946

By John P. Powell, J. L. Eakin

"INTRODUCTION AND SUMMARYNowata County, in the northeast corner of Oklahoma, is one of the principal oil-producing counties of this stripper area. Many fields in the county were opened and much oil was produced before statehood. The location of the major fields, as defined by the Oklahoma Corporation Commission, 2/ the outline of the areas of water-flooding activity, and the location of the several projects described in detail in this report are shown in figure 1.There was some drilling in the county earlier; but it was not until after 1904, when the Secretary of the Interior confirmed as valid the leases granted by the Cherokee Nation, that the major drilling activity began. Initial development in this part of Oklahoma was in the Chelsea field in Rogers County, which adjoins Novata County on the south. The activity spread rapidly northward to the Alluwe and Coody's Bluff fields, and then to the Nowata-Claggett field. Continued exploration resulted in discovery of the Delaware-Childers field, where some wells having an initial production of 1,000 barrels daily were completed. Fields discovered and developed during the next few years included the Lenepah (Elliott), Adair, California Creek, Curl Creek, Woody, and South Coffeyville. The oil-production history of Nowata County is shown in figure 2. In assembling the data for a production curve, it was found that the combined production records for Nowata and Rogers Counties were available for 1914 to 1951, inclusive, and that records for the individual counties were available only from 1926 to 1951, inclusive. The early production figures for the counties from 1905 to 1914, inclusive, except for 1909, were calculated from the initial production statistics of the Federal Geological Survey mineral resources bulletins and production data assembled by C. H. Beal. 3/ The production values for 1905 to 1926 for Nowata County were obtained by dividing the total production for the two counties by a percentage factor derived from known facts regarding the oil industry in the area. Production figures for the individual counties from 1926 to 1933, inclusive, were obtained from the files of the Oil and Gas Journal, and the figures from 1933 through 1951 were obtained from monthly reports of the Oklahoma Corporation Commission."

Jun 1, 1952

By William J. Campbell

The purpose of this investigation was to extend the analytical services which are required for Bureau of Mines programs in developing and evaluating high-purity materials. Determination of trace elements in minerals and ores as an aid in geochemical evaluation and prospecting was considered. Serious consideration should be given to the merits of using the avail- able fluorescent X-ray spectrographic instrumentation and techniques for determining trace elements. Limits of detectability for trace elements in metal, oxide, solution or mineral samples range from 0.1 to 100 p.p.m, depending on the element being determined, overall sample composition, and the complexity of the X-ray spectra; limits of detectability range from 0.01 to 1 microgram for elements that have been preconcentrated by a chemical or physical process, for example, by ion-exchange membrane.

Jan 1, 1962

By Dong G. Chae

A model for the leaching of oxide ores is developed and II correlated with laboratory tests for percolation leaching of copper oxide are. Using the model, recovery of metal values and lixiviant concentration of the effluent solution at any time may be evaluated. For the copper oxide ore a simplified version of the model is examined for the leaching mechanism consisting of: 1) a surface flush reaction with the highest rate of lixiviant consumption; 2) penetration of lixiviant to react with copper minerals and gangue constituents; and, 3) slow lixiviant consumption, mostly by residual gangue materials. The simplified model is able to explain reasonably the leaching behavior of copper oxide ore by introducing a concept of effective initial size to correct for packing in a bed of fine particles.

Jan 1, 1979

By R. K. Koch

The vapor pressures of liquid molybdenum and liquid zirconium were determined by the Langmuir free-evaporation method. An electron-beam furnace with a water-cooled copper crucible was used for melting. Temperature was measured with a two-color ratio pyrometer. The vapor-pressure data led to the following equations: [log p (atm) = 5.429 - 28,380 T for liquid molybdenum in the range 2,890° to 2,990° K, and log p (atm) = 6.521 - 30,940 T for liquid zirconium in the range 2,229° to 2,795° K.] Third-law evaluations of each data set gave mean heats of sublimation (298.15° K) of 157.6 ± 1.8 kcal/mole and 148.4 ± 2.4 kcal/mole for molybdenum and zirconium, respectively, where the uncertainties are two standard devia¬tions. Second-law standard heats of sublimation determined from sigma plots and tabulated enthalpies were 143.5 ± 2.7 kcal/mole and 149.2 ± 3.8 kcal/mole for molybdenum and zirconium, respectively. The better agreement in heats of sublimation for zirconium is attributed to the 566° K temperature range studied which permitted a more accurate definition of the vapor pressure curve than could be obtained from the 100° K span for molybdenum. This supposition was verified by making a sigma-prime plot which utilized solid vapor pressure data for molybdenum to extend the evaluation range by 800° K. This gave a standard heat of sublimation of 155.2 ± 1.6 kcal/mole which is in good agree¬ment with the third-law value. The plot also gave a standard entropy of sublimation (298.15° K) of 35.73 ± 0.48 eu.

Jan 1, 1968

By Joseph W. Town

The Bureau of Mines conducted studies related to SO2 air pollution to determine attritioning rates, SO2 sorption rates, and sulfur loads that could be obtained on commercial alkalized alumina sorbent pellets. Fluidized-bed attritioning rates ranged from 0.025 pct/hr for alkalized alumina with a crushing strength of 4 kg to 0.075 pct/hr for 0.5 kg crushing strength mate¬rial. Airlift attritioning rates ranged from 0.50 pct/hr for 3 kg crushing strength alkalized alumina to about 3 pct/hr for 0.5 kg material. Attritioning rates for the commercial alkalized alumina were comparable to those obtained for sorbent pellets prepared in the Bureau of Mines laboratory. Sorption rates were related to S02 concentration in flue gas, temperature, and presence of nitrogen oxides in the gas stream. Sorption rates at 300° C were 0.35 X 10-6 gS/gp/sec (grams sulfur per gram pellet per second) in 0.045 pct so, gas, 5.1 x 10-5 gS/gp/sec in 0.34 pct SO2 gas, and 65 X 10-5 gS/gp/sec in 10 pct SO2 gas. For the 0.34 pct S02 gas, sulfur loads of 0.10 gS/gp (the projected load for regeneration) were obtained in 47 min at 130° C and in 116 min at 300° C. The presence of either NO or NO2 in the 0.34 pet S02 gas increased the SO2 sorption rates 2 to 3 times at 300° C, but had no effect at 130° C.

Jan 1, 1969

By W. W. Adams

Reports received by the Bureau of Mines, Department of Commerce, from State mine inspectors, for November, 1930, showed that 219 men were killed in the coal mines of the United States during the month, an increase of 25 over the previous month and 33 over November, 1929. On the other hand the production of coal decreased, the output of 43,329,000 tons in November being 8,397,000 tons less than in October and 9,005,000 tone less than in November a year ago. The larger number of fatalities accompanied by a smaller output of coal resulted in a higher death rate4 per million tons in November than in the same month last year or in October, 1930. The November rate was 5.05, as compared with 3.55 for November, 1929 and 3.75 for October, 1930. The increase in the rate for the industry as a whole was chargeable entirely to bituminous mines, as the anthracite mines had fewer fatalities in November than in either of the previous months to which reference has been made. Reports for bituminous mines alone showed that accidents at this class of mines resulted in a death rate of 5.12, based on 195 fatalities and a production of 38,122,000 tons. This rate indicated an increase of 55 per cent over the rate for October, of the same year, and 72 per cent over the rate for November, 1929. The October record was 146 fatalities and 44,150,000 tons, and that for November a year ago was 138 deaths and a production of 46,514,000 tons.

Jan 1, 1930

By Gilbert M. Farrior

The electrical resistivity the coefficient of electrical resistivity the Hall coefficient, and the absolute thermoelectric power were determined in this Bureau of Mines investigation for nine compositions of the TiB2-CrB2 sub-system. The numerical values of the electrical resistivity and the thermo-electric power were greater for the intermediate compositions than for the end members. The absolute values of the Hall coefficients and the coefficients of electrical resistivity were less for the intermediate compositions than for the end members. The electrical resistivities and Hall coefficients were about the order of magnitude of most metals--from 34 to 202 microhm-cm and from about 0 to -23.3 X 10-4 cuP/coulomb. The thermoelectric power was somewhat greater than that of most metals--up to 15.6 microvolts per 0 C.

Jan 1, 1965

By H. E. Powell

Magnetic susceptibilities were determined by the Bureau of Mines fur 19 cobalt- and nickel-bearing minerals and for a suite for synthetic cobalt-nickel diarsenides analogous to the rammelsbergite and safflorite series. Relations between susceptibility and composition were found to be nonlinear for both impure natural minerals and pure synthetics.

Jan 1, 1967

By H. C. Miller

[California's sensational rise to supremacy as an oil-producing State in 1923 was accompanied by a loss of 62 lives. These 62 deaths were from oil-producing accidents alone and do not include fatalities at the refineries, on tankers, or on any work not directly connected with the drilling for and the production of oil. The number of facilities for 1923 was 82 per cent greater than in 1922, the next most fatal year, with a record of 34 lives lost. The data submitted in Table 1 show that for the calendar years 1917 to 1923 inclusive, an average of 4.74 million barrels of oil were produced per Vitality in the California oil fields. On this basis, the record for 1923, hough a trifle below the average, shove up slightly better than that for 1922.]

Jan 1, 1924

By Fun-Den Wang

A two-dimensional plane strain analysis by the stiffness matrix method was used to analyze two basic pit slope configurations. The magnitudes and the directions of stresses are given for a V-shape and for a flat-bottom pit with the slope angle varying from 30° to 90° at 10° intervals, Stress effects due to irregular pit configuration or to in-situ forces are discussed. Equations of similitude for gravity loading are given. Expressions are also given for the stresses at the toe as a function of slope angle. Procedures are given for finding the stresses in any geometrically similar pit slope of different dimensions and material properties from the stresses and equations presented in this report. Numerical results show that the V-shape pit slopes have lower stresses than the flat-bottom pit slopes; hence, they are inferred to be more stable.

Jan 1, 1970

By J. B. Umhau

During 1928 the United States consumed 73,270 long tons of virgin or primary tin, which was approximately 7.5 per cent more than the 68,198 long tons con¬sumed in 1927 and equaled 41 per cent of the world's production in 1928 (approximately 178,000 long tons). Consumers' stocks amounted to 9,268 tons on January 1, 1928, and 8,587 long tons on December 31, 1928, a net reduction of 681 tons. In addition to the virgin tin accounted for above, 12,106 long tons of secondary metallic tin were used by manufacturers of tin products in 1928. These figures are the result of an inquiry addressed by the Bureau of Mines to manufacturers to determine the amount of metallic tin used by them; in reply, 1,307 establishments reported consumption in 1928. The distribution of the amount consumed by various uses, as shown in the allowing tabulation based on Bureau of Mines canvasses for 1927 and 1928 in comparison with consumption by uses reported by the War Industries Board for 1917, emphasizes the fact that new uses for tin have been developed in only minor or insignificant amounts. Furthermore, although the studies for recent years show that some older uses have been discontinued, the amounts involved were all small and insignificant. Variation in consumption from year to year parallels the fluctuations in demand for the already well-established tin products. For example, the manufacture of bearing metals and solders for motor cars and trucks required 19,000 tons in 1928 compared to 16,000 tons in 1927; the canning industry continues to require the greater portion of the tin plate and also much solder. Growth in the electrical and the more recently developed industries (aeroplane, refrigerators, radio, etc.), while affecting total consumption of bearing metals, solders, etc., has made little change in the proportions required for these basic methods of using tin.

Jan 1, 1929

By R. Hogg, S. Chander

"The distribution of the wettability of coals of different rank was determined by measurements of contact angles for individual particles. The contact angle was estimated from the equilibrium partitioning of a particle at the water/air interface. Using this technique contact angles were determined for a larger number of particles from a given sample and a frequency distribution of contact angle was obtained. The contact angle distribution was broad for all the coals tested with included an anthracite, a hvA bituminous and a sub-bituminous coal. In comparison, spherical particles of polymethylmethacrylaie gave a much narrower distribution. The distribution for irregular polyethylene particles was somewhat broader than that for the polymethylmethacrylate spheres but broader than that for the polymethylmethacrylate spheres but considerably narrower than that for coal. The broader wetting distribution for coal was attributed to differences in surface chemical properties.INTRODUCTIONA knowledge of the wetting properties of coals is very useful in coal cleaning by flotation and other processes in which separations are based on differential surface properties. The various methods available for measuring wetting characteristics include: contact angle, 1-2 time, time, 3-5 bubble attachment, 6 film flotation,7 displacement pressure, 8-9 penetration rate, 10-11 bubble pick-up, 12 induction time, 13 imbibition time, 14 and calorimetry. 15-16 Of all these methods, however, the measure¬ment of contact angle by the sessile drop and captive bubble techniques have been most widely used. Brady and Gauger"" demonstrated through the use of the contact angle method that the natural hydrophobicity of coal varied greatly from sample to sample. Subsequent experiments showed that this difference correlated well with rank, the larger contact angles generally being associated with the higher rank coals. 18-19 More recent studies by Aplan and co-workers' show that the wettability of various ranks of coals as determined by sessile drop and captive bubble methods is a more complex function of rank. The hydrophobicity of coal usually increases with rank up to about 80% fixed carbon (dmmf) and then decreases."

Mar 1, 1992

By R. V. Ramani, R. Bhaskar

"While the National Academy of Sciences has stated that gravimetric sampling technology for compliance purposes is adequate, research into various aspects of respirable dust control require data on many other parameters of airborne dust. These, in turn, have created the need to use many instruments, other than personal gravimetric samplers, in mi ne environments for dust measurement. There is a need to evaluate the performance of these instruments under conditions of potential use.As part of research in the Generic Technology Center for Respirable Dust, cascade impactors, gravimetric personal samplers and gravimetric samplers collecting dust using isokinetic sampling principles were employed for dust measurements under identical conditions in a mine airway. During the course of the experiments, 8-stage cascade impactors and gravimetric samplers drawing air isokinetically were located in the center of a mine airway at various stations. Two types of data were examined - concentration of dust and size distribution of the dust collected in the samplers. The data show that the amount of dust collected by an impactor is less than half the amount collected isokinetically. The size distributions of the dusts collected from the two instruments, though comparable, show a consistent difference in median diameters. The cause for this bias is examined.The paper presents and discusses the results of the tests, including the concentrations and size distributions obtained from the two instruments for different experimental conditions. There is a need to document the performance of various dust measuring devices in mine airflow conditions.INTRODUCTIONThe sampling of airborne dust in mines can be done for several purposes. Traditionally, dust sampling has been restricted to the gravimetric measurement of airborne respirable dust to comply with the regulations governing the mining industry. Instruments such as the MRE gravimetric sampler, and personal gravimetric samplers that have collection characteristics similar to the human respiratory system have been in use for the last two decades. Presently available instrumentation for the purpose of regulation have been considered adequate by the Committee on the Measurement and Control of Respirable Dust in Mines (National Academy of Sciences, 1980),"

Jan 1, 1989

By Y. L. Su

Deterministic and stochastic simulation were combined to develop a computer model of an open pit mining system using bucket wheel excavators and related materials handling equipment. The model is closed and dynamic in the sense that information is fed back to control activities at various levels and reservoirs. The results of interaction between unit operations in one time interval determines overall system behavior for the next interval. Equipment performance curves and system profile characteristics rather than time studies are applied to determine the operation of each activity at any time period. For that part of system where performance is dictated by a random variable~ subjective probabilities are employed. Two stages of research were considered to formulate this model. Stage one involved the formulation of equipment sub-assemblies for the sequence of equipment moves along with related assignments and routines for information retrieval. The second stage of research combined all sub-assemblies into an integrated open pit mining simulator. The model is not tailored for any specific open pit operation but is readily adaptable to any system of surface mining including operations having a high degree of complexity. Questions answered by the model include: 1) system design and selection of equipment for a new mining operation; 2) analysis of existing operations for possible changes, additions or general

Jan 1, 1971