Search Documents

By G. St. J. Perrott, N. A. Tolch

"The measured strength of an explosive depends to a certain extent on which it is determined. An earlier investigation showed the relative propulsive strength of dynamites as determined in one type of apparatus, ballistic pendulum.4 The aim of this paper is to precept strength data on these same dynamites determined in another type of apparatus, the Trauzl lead block, and to compare the results with those of the ballistic pendulum. Trauzl lead block have been in use many years for the determination of thy strength of explosives, under moderate confinement.5 The common practice is to shoot 10 grams of explosive, in tinfoil wrapper,- and then to measure the volume of the cavity produced by the shot. The volume of the original borehole is deducted from the gross expansion and sometimes a correction is made for the expansion produced by the detonator. Dry sand is used for stemming the charge.It has been found that the expansion in Trauzl blocks is not strictly proportional to the charge. Naoum5 believed that for scientific accuracy the charge should undoubtedly be regulated to give the same average expansion for each sample tested, but for expansions of 200 to 400 cubic, centimeters the deviation from proportionality is not sufficient to give results appreciably in error.Neubner7 found that the proportionality curve is tangent to the charge-expansion curve at about 300 cubic centimeters expansion, provided that no deductions are made for the volume of the original borehole or the effect of the detonator; the total or gross expansion is proportional to the charge between expansions of 250 to 350 cubic centimeters without serious error."

Oct 1, 1930

The REL of 1 mg/m3 for respirable coal mine dust does not assure a zero risk for the development of occupational respiratory diseases among all miners exposed during a full working lifetime. Consequently, a medical screening and surveillance program that includes initial and periodic chest X-rays and spirometric examinations is important for the early detection of disease and the prevention of "material impairment of health or functional capacity" [30 USC 8 11(a)(6)(A)]. The medical screening and surveillance program is also useful for disease surveillance, which includes the tracking trends, the setting of prevention and intervention priorities, and the assessment of prevention and intervention efforts. NIOSH encourages both underground and surface coal miners to participate in the medical screening and surveillance program.

Jan 1, 1997

By Bill M. Stewart, Philip W. Patton, Curtis C. Clark

Handling materials in underground mines continues to be a major safety problem. To help reduce materials-handling injuries, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are investigating those materials-handling tasks in underground mines that appear to generate a high number of injuries. Data from the Mine Safety and Health Administration for the years 1989-1999 were studied to find out if there were any trends in materials-handling accidents and if so, to determine what tasks were involved and the sources of injuries. Several underground coal and metal mines we revisited to document innovative materials-handling technologies. Considerations for safety training and mechanization needs for continued reduction in materials-handling injuries are described.

By Charles L. Kimbell

Comprehensive data on market prices for crude minerals and mineral products for the world as a whole do not exist, and even the data that are available are not necessarily compatible between countries, particularly between the market economy countries and the centrally planned economy countries. Further, it should be evident that the actual delivered price for a small quantity of any specific commodity at some point substantially removed from a production facility or a seacoast port will differ appreciably from that for a large volume of the same product at or near its production source or a major import center. Nevertheless, the regularly published prices of selected major mineral commodities in key market areas can be regarded as indicative of general world price trends.

Jan 1, 1992

By Jacob N. Frank

A factorially designed, hydraulic fragmentation experiment using a high-pressure water jet was conducted on concrete blocks. Three levels of pressure, standoff distance, and impact angle and two levels of traverse time and surface condition were used. Three variables were measured: depth of penetration, volume of material removed, and width of slot. Three stepwise linear regression equations were developed from the jet parameters and the physical properties of the concrete. The three basic equations, describing the significant jet parameters and physical properties, were developed into 15 predictor equations, five for each variable investigated. Direct regression equations were also developed for each variable investigated to show the result of increasing or decreasing each significant variable. Energy efficiencies were developed for the experiment and for each significant factorial variable.

Jan 1, 1971

By A. W. Deurbrouck

This report presents the results of a washability study of 322 coal mine samples showing the sulfur forms and distribution in the coals. The samples were collected from mines which were principally utility coal producers. Generally, the data show the total sulfur content of the coals evaluated could be significantly reduced by some combination of stage crushing and specific gravity separation. However, few coals could be upgraded to a final product containing 1 percent or less total sulfur. The complete washability data are presented for each sample processed. A statistical evaluation is included for the coalbeds from which more than 10 samples were collected and for the geographical coal producing regions. A graphical summation is presented for the coal producing regions and selected coalbeds.

Jan 1, 1972

By R. Barany

In this paper, closed expressions have been obtained for the frequency spectrum of a Born-Karman square lattice in terms of elliptic and hyperelliptic integrals. This work is part of continuing research by the Bureau of Mines with the thermodynamic properties of metals and minerals. Although other workers have obtained various types of approximations for the general case of the frequency spectrum of a square lattice, no one previously has obtained closed analytic expressions for this spectrum. To understand the optical and thermodynamic properties of crystals, several investigators have studied the distribution of frequencies of normal modes of vibration of the crystal lattice. Born and Karman3 laid the foundation for the theory of lattice dynamics and obtained detailed results for the case of a one-dimensional lattice. Blackman4 used numerical techniques to estimate the frequency distribution of a two-dimensional square lattice. Mbntroll5 analytically determined the frequency distribution of a square lattice for a particular value of the force constants. He also studied the more general problem and obtained some analytic approximations, using the method of moments. However, the calculations by this method were so difficult that it was not always practicable to carry them out. Van Hove6 and Montroll7 studied the nature of the singularities in the frequency spectrum of both a two and

Jan 1, 1962

By John C. Cook

This was a study to identify and evaluate known technologies employing electromagnetic resonance phenomena in solid minerals for their identification and assaying, particularly assay logging of exploratory boreholes. A comprehensive literature search and study revealed some little known NMR (nuclear magnetic resonance) techniques developed by Professor G. J. Béné's group at the University of Geneva, Switzerland. These are suitable for use in weak, inhomogeneous magnetic fields. Laboratory NMR tests of numerous U.S. ore minerals showed good identifying signals from phosphates, fluorspar, bauxite, oil shale, and spodumene (lithium) ores, but not from the copper, lead, antimony or manganese ores tested. Use of EPR "signatures" for such ores is suggested. A conceptual design for an NMR assay logging system is proposed.

Jan 1, 1978

"SUMMARYThe K.M.A. reservoir was discovered to be oil bearing at a depth of 3,719 feet on March 11, 1931. Extensive development, however, was not begun immediately, because the discovery well had a low initial daily oil production, and market conditions for oil were unfavorable. Development of the field progressed slowly for the next 6 1/2 years. In the latter part of 1937, a wildcat well approximately 2 miles southwest of the discovery well was drilled on a magnetometer high and completed with an initial flowing production of 2,016 barrels of 43° A.P.I.-gravity oil in 12 hours. Rapid development of the southwestern part of the K.M.A. field was begun immediately and continued until over 700 wells were drilled and approximately 12,500 acres proved oil productive.Because of the large size of the entire K.M.A. field, this report is limited in scope to the southwestern part only, and the discussion that follows pertains to this area only. The closing date for production statistics is August 1, 1949.The K.M.A. structure is a complex anticline having a maximum closure of 250 feet, and the K.M.A. formation is composed of sediments that grade from limestone through sandy lime and limy sand to sandstone with thin streaks of shale. Two distinct members of the K.M.A. formation, zone I and zone II, are oil productive. Core analyses indicate the average porosity to be 16.5 percent for zone I and 16.1 percent for zone II. A relationship was established from core data, which showed the correlative permeabilities to be 42.1 millidarcys for zone I and 39.5 millidarcys for zone II, whereas the arithmetical averages of the permeabilities were 84 millidarcys for zone I and 216 millidarcys for zone II. Connate water saturations were 17.5 percent for zone I and 20.0 percent for zone II. The porosity-saturation method, using a thickness-correction factor, was employed to calculate the volume c 168.1 million barrels of stock-tank oil initially in place in the reservoir. Analyses of the reservoir oilIn that, although the initial reservoir pressure was 1,750 p.s.i., the original reservoir oil was saturated to only 1,300 at which pressure 1 barrel of stock,tank oil contained 525 cubic feet of gas in solution.A serious decline in reservoir pressure during the 2 years of rapid development alarmed the operators and caused them to consider a cooperative pressure-maintenance program. In the latter part of 1939, the K.M.A. Pressure Maintenance Association was organized, and the gasoline plants in the field agreed to process the wet gas and return the dry gas to leases having gas-injection wells. Approximately 27 percent of the cumulative volume of produced gas had been returned to the reservoir by August 1, 1949."

Jun 1, 1952

By Kay E. Goldberg

The Bureau of Mines conducted a study to develop and evaluate a training workshop for mine safety training personnel. The workshop was based on the Instructional Development Institute (IDI) which has been used for nearly ten years to train educators and administrators in the application of a nine-step model for defining, developing, and evaluating instruction. The Mining Instructional Development Institute (MIDI) was developed by investigators at the University of Southern California as a two-phase project. Phase I involved the modification of the six-day IDI program (including audiovisual presentations, workbooks, games, and exercises) for use by mine safety trainers as a workshop lasting three and one-half days. Phase II involved the evaluation and validation of the prototype MIDI workshop by means of a two-stage jury of experts and a prototype field trial. On the basis of data collected in the validation process it was determined that the institute provided an effective and useful method of instruction in mine safety training and that the institute would be especially valuable for mine safety training administrators and supervisors.

Jan 1, 1980

By Svend [Bue] Rondum

The final report contains a summary of the work performed under this contract, In addition to the report itself, other products were derived from this effort. Several hardware items were prototyped for use with underground belt conveyors, and a manual for installation and maintenance procedures was developed and published under separate cover. Recommendations have been included for implementation of the tools and the manual or, an industry-wide basis.

Jan 1, 1982

By Howard M. Stainer

Published X-ray mass absorption coefficients were compiled and tabulated. These coefficients are required for various X-ray analytical techniques. Values obtained from 28 authors are listed for 87 elements with both experimental and calculated points included; the wavelengths range from ~0.01 to 68 A. Representative graphs are presented for six elements (lithium, nitrogen, iron, silver, holmium, and uranium. A 37-item supplementary bibliography is also included.

Jan 1, 1963

By Howard M. Stainer

Published X-ray mass absorption coefficients were compiled and tabulated. These coefficients are required for various X-ray analytical techniques. Values obtained from 28 authors are listed for 87 elements with both experimental and calculated points included; the wavelengths range from 4.01 to 68 A. Representative graphs are presented for six elements (lithium, nitrogen, iron, silver, holmium, and uranium. A 37-item supplementary bibliography is also included.

Jan 1, 1963

By C. P. Mangelsdorf

This report deals with the efforts to develop a portable device suitable for underground use for the purpose of measuring the frequency of vibration of the horizontal chords of Birmingham roof trusses. Four devices are investigated and evaluated. An approximate emperical expression developed from a mathematical analysis provides a means of converting the frequency into tension. The method appears to be effective in mines with shale roof but requires some modification for other roofs.

Jan 1, 1983

By H. J. Seim

An ion-exchange-instrumental analysis technique is described for analyzing impurities at 1 to 1,000 parts per million level in rare-earth metals. A cation-exchange flame photometric method is used for the alkali and alkaline earth groups of metals, and an anion-exchange procedure is used in conjunction with polarographic and X-ray fluorescence techniques for selected transition elements. The standard deviation is about 6 percent, and the average error, about 5 percent.

Jan 1, 1962

By Donald S. Colby

CARBON-BLACK shipments, which had declined in the latter art of 1953, remained low in 1954 until after settlement of the labor strike that occurred in the rubber industry in July and August. The production of new model automobiles in the last quarter of the year spurred the demand for rubber tires and consequently the demand for carbon black. Total shipments of 1,498 million pounds for the year were 4 percent below 1953.

Jan 1, 1958

By B. W. Haynes

This Bureau of Mines report describes the laboratory processing of manganese nodules and the results of tailings characterization obtained during the cooperative program with the Department of Commerce's National Oceanic and Atmospheric Administration (NOAA) and the Bureau. Five technically feasible first-generation nodule processing methods were operated at bench scale to generate sufficient tailings and slags for physical and chemical analyses. A description is given for the laboratory operation of the individual unit operations of each process. The laboratory-generated tailings and slags were tested for physical properties, mineral content, elemental and ion content, and leachability for all five processes. The results of leachate testing using the Environmental Protection Agency extraction procedure (EP) toxicity test, the American Society for Testing and Materials shake extraction test, and the EPA-U.S. Army Corps of Engineers seawater elutriant test showed very low to negligible leaching of metals from the tailings and slags. Results of the EP toxicity test demonstrated that the wastes are nonhazardous as defined in the Resource Conservation and Recovery Act (Public Law 94-580).

Jan 1, 1985

By Otto Ruhl

"INTRODUCTION With the conclusion of the war and the ensuing readjustment of industry to peacetime conditions, the Bureau of Mines recognized that definite and complete figures on the reserves of zinc and lead ores in the Tri-State District would be needed for an evaluation of the problem of reconversion. In October 1945 its engineers began examination of all the mines and pros¬pects in the Tri-State area and assembling of the basic data for a complete detailed estimate of the reserves of the field. Six to twelve months will be required to complete the report with the personnel available; therefore, it has been deemed advisable to provide as much data as possible for imme¬diate use. Accordingly, a confidential report prepared in January 1944 for the use of and in cooperation with the War Production Board has been brought up to date to form the basis of this preliminary estimate of reserves.The 1944 report has been revised by first subtracting from the reserves then set up for each mill group the amounts mined and milled by those properties for 1944 and 10 months of 1945, with November and December estimated. These production statistics were taken from the monthly reports of the Metal Economics Division of the Bureau of Mines. The remaining reserves were then adjusted by additions of tonnages of new reserves disclosed by developments during the years 1944 and 1945. Such additions were based upon the data furnished by various operators, upon estimates supplied by the Federal Geological Survey District Office at Miami, Okla., and upon estimates of the engineers of the Bureau of Mines Joplin field office.It is apparent from the work so far accomplished in the detailed exami¬nations now under way that the final estimate of reserves will probably be somewhat greater and will differ to a certain degree from these preliminary totals, not only as to the tonnages of ere but also as to grades and distribution by areas. This is due to the fact that all the factors of development, exploration, and geology are being considered in the present examination and report for each individual mine and prospect, whereas the previous reports covered only the immediate development factors surrounding each mill group then in active operation or projected for operation at some early date in accordance with the possible needs for war production."

Aug 1, 1946

By W. W. Adams, T. D. Lawrence, D. R. White

"This paper presents the results of the eleventh yearly accident-prevention contest, the National Safety Competition of 1935, conducted by the United States Bureau of Mines. Participating in the competition were 336 mines and Quarries in 37 States. Five mining or quarrying companies, each the leader in its group for having established the best safety record during the year, were awarded the national safety trophies 'Sentinels of Safety.Since these annual contests were begun 11 years ago the scope of the competition has been broadened materially, both as to the number of plants participating and as to the number of man-hours of exposure to accident hazards. Moreover, marked progress in the pre¬vention of accidents has been achieved, as is indicated by an almost constant downward course in the accident-frequency rates for the contest group as a whole during the past 11 years. On the other hand, the accident-severity rates for the group showed an upward trend during the first part of the period and a downward trend during the latter part, except in 1930 and 1934, when two disastrous explosions occurred with heavy loss of life, and in 1935, when there was an increase in the number of fatalities although no major disasters occurred. The accident rate for 1935, both as to frequency and severity, was higher than for 1934.The National Safety Competition is conducted by the Bureau of Mines in the interest of safety in the mining and quarrying industries. This object is accomplished directly through the efforts of the competing companies and their employees to win first place in the competition and thereupon receive well-merited and national recognition for their achievement. Indirectly the purpose of the contest is accomplished through studies by the Bureau of Mines of the fasts contained in the accident reports which the competing companies furnish to enable the Bureau to compute the accident rates that are the basis for determining the winners of the contest.The statistics that constitute the basis for determining the winning companies and the relative standing of all companies are prepared uniformly without regard to the States in which the companies operate, or to differences in classes of accidents covered by State laws relating to compensation for injuries resulting from industrial accidents."

Jul 1, 1936

By A. Salmoni, E. K. Gillin, T. Eger, A. Cann, P. Vi, M. Hunt

Kittusamy (Kittusamy & Buchholz, 2004) state that there have been few studies conducted to assess exposure to whole-body vibration (WBV) in the construction industry. They suggest that there is very little reliable data from the construction industry that characterizes exposure levels to various hazards including WBV or the health outcomes from such exposure and that there is a need for more exposure data. In a recent exploratory study of heavy construction equipment Cann (Cann, Salmoni, Vi, & Eger, 2003) looked at vibration levels for 14 different types of construction equipment. Eight of the 14 pieces of equipment tested exposed operators to levels of WBV that exceeded the recommended limits for an 8-hour period when comparing the measured VDV to the ISO 2631-1 standards. The purpose of the present research was not only to test a larger number of scrapers but also to investigate scraper operator exposure to whole body vibration (WBV) separately for each task. Methods 33 scrapers were evaluated for WBV in a variety of residential and road construction projects. Testing equipment consisted of triaxial accelerometers that allowed vibration data collection in all three orthogonal axes, with the x-axis positioned to measure vibration in the anterior-posterior direction, the y-axis in the medial-lateral direction, and the z-axis in the vertical direction. Root mean square accelerations (aRMS), vibration dose value (VDV), crest factor, and maximum transient vibration values (MTVV) were derived from this software and exported to an Excel™ spreadsheet for later data analysis. Test sessions for each piece of equipment lasted for approximately 20 minutes until at least three work cycles had been completed. Tasks included: idling while waiting for a bulldozer to push the scraper through the scraping phase, scraping, traveling loaded with dirt, dumping and traveling empty. Results Task breakdown by time reveals 25% of the work cycle was spent traveling fully loaded with dirt, 19% dumping, 21% traveling unloaded, 17% idling and 18% scraping. Calculation of aRMS vector sums gave values of 2.55 m/s2 during loaded transport, 2.46 m/s2 during dumping, 2.31 m/s2 during unloaded travel, 0.55 m/s2 during idling and 1.46 m/s2 during scraping (see Table 1). The highest acceleration values recorded were found in the z-axis during fully loaded transport reaching an average aRMS over three work cycles of 2.55 m/s2.

Jan 6, 2006