Search Documents

By M. J. Ferrante

The Bureau of Mines determined the enthalpies of Ni3S2 relative to 298.15 K to provide new thermodynamic data for advancement of mineral science and technology. Enthalpies were measured with a copper-block calorimeter from 298.15 to 1,197 K. A solid-solid transition was found at 834±1 K, with an isothermal heat absorption of 13.32 kcal/mol. The temperature of this solid-solid transition was accurately measured by differential scanning calorimetry. Because Ni3S2 does not melt congruently, the heat of fusion of 4.70 kcal/mol was obtained by extrapolation of enthalpy measurements from the solid and liquid phases to approximately 1,064 K. Tabulated values are given for the relative standard enthalpy, heat capacity, entropy, and Gibbs energy function between 298.15 and 1,800 K. Enthalpies are also given in equation form and combined with data from the literature to derive values of standard enthalpies of formation and Gibbs energies of formation. Similar calculations were made for the reaction of crystalline and liquid nickel with gaseous diatomic sulfur for Ni3S-2(c, l).

Jan 1, 1982

By Robert P. Vinson, Fred N. Kissell, Edward D. Thimons

Because of the high number of accidental methane gas ignitions in metal and nonmetal mines, the Bureau of Mines searched for a simple guideline that would allow mine personnel to evaluate the methane hazard in a given mine. Air samples were collected by the Bureau in 53 metal and nonmetal mines and analyzed for trace evidence of methane gas. Samples were collected in the returns and at the working faces. Those mines classified as gassy by the Mine Safety and Health Administration had a significantly higher average methane concentration than those classified as nongassy. Of the 9 gassy mines sampled, 7 had methane concentrations above 100 ppm, whereas only 1 of the 44 nongassy mines had a concentration above 100 ppm. The 100-ppm concentration may be used as a simple and convenient guideline for forecasting the methane hazard in a mine, whether or not the mine is classified as gassy. There was no consistent correlation between commodity mined and methane concentration, nor was there a correlation between mine depth and methane concentration. Neither of these factors can be considered a guideline for predicting methane hazards.

Jan 1, 1979

By Connie S. Musulin

The Bureau of Mines conducted an experiment at Exxon Mineral Co.'s Buffalo Shaft Operation to determine the time required for radon concentrations to return to a base average after fan shutdowns. Shutdown times ranging from 5 min to 16 hr were evaluated. An equation was derived to calculate a ratio that determines the time required for the radon concentration to return to the average level that existed in the mine prior to shutdown. For fan shutdowns of 15 min or more, underground personnel should be evacuated to areas with natural downcast ventilation. For shutdowns of less than 1 hr, personnel should not return to the working area until the elapsed time is four times the shutdown, or until the working area is resampled and found safe. If the mine is not in production during weekends, the downcast fans can be turned off .from midnight Friday until 4 p.m. Sunday, and the radon daughter concentration should be below 1 WL throughout the mine by the start of the shift Monday. This fan shutdown would conserve energy and save the mining company an estimated $21,000 each year.

Jan 1, 1982

By Jürgen F. PH. D. Brune, Alex C. Smith, Michael A. Trevits

Underground coal mine fires in the United States continue to present a significant hazard to the safety and health of mine workers. The leading causes of mine fires include flame cutting and welding operations, frictional heating and ignitions, electrical shorts, mobile equipment malfunctions, and spontaneous combustion The National Institute for Occupational Safety and Health (NIOSH) is conducting an in-depth program of research to address mine fire prevention, early and reliable fire detection and mine fire suppression and control technologies. One segment of the research portfolio is focused on remote methods for addressing coal mine fires. This research is important because remote methods represent the primary means of fighting a mine fire when conditions are too dangerous to fight the fire directly underground. Technologies under investigation include remote methods for installing ventilation control devices (mine fire seals) and remote methods for suppressing the fire using, the injection of inert gas, gas-enhanced foam and jet engine exhaust gases into the fire zone. This paper presents a summary of remote mine firefighting technologies used in the U.S. and the results of completed NIOSH research.

By D. E. Seizinger

Analytical methods for oxygenates in exhaust gases were studied, and emissions of these compounds from automotive engines were measured with and without an oxidation catalyst in the exhaust system. Hydrocarbons, simple mixtures of hydrocarbons, and a single gasoline were used as fuels. With the more complex gasoline, successful analysis was possible only with exhaust from the catalytic system which preferentially converted and thus removed interfering hydrocarbon species. However, it was shown that an estimate of the oxygenate yield from gasoline used in a noncatalytic system can be synthesized from data obtained with simple fuels. Such synthesized data were used for comparison of noncatalytic with catalytic systems. Compared with those of previous studies, results of this work indicate that the action of the catalyst introduced no new oxygenates and reduced both the carbonyl and the total of oxygenates. It is concluded that the compositional character and class distribution of oxygenates in exhaust from catalytic systems may differ significantly from the composition and distribution for oxygenates not subjected to catalytic conversion. The findings also support previous estimates that noncarbonyls may constitute a significant fraction of exhaust oxygenates and may warrant attention in procedures for measurement of the oxygenates.

Jan 1, 1973

By Charles D. Martens

Raw non fuel minerals produced in the United States during 1981 had an estimated value of $25 billion, about the same as that of 1980. In terms of 1980 dollars. the value of minerals produced during 1981 was $23 billion.2 This chapter includes tables for 1980 that were not available for publication in the 1980 Minerals Yearbook, but does not include the corresponding tables for 1981. The underlying causes of the overall decline in U.S. nonfuel mine production during 1981 were varied, but the common factor was the worldwide recession. In some cases the decline was traced to foreign competition. For example, iron ore production was lower in part because of increased imports of steel products such as coiled steel sheet. Another problem experienced by the domestic mining industry was the continuing difficulty in attracting capital. This was due in part to the attractiveness of investments outside the mining industry, such as short-term, high-interest securities. Another reason was the importation of commodities from countries where overall costs were lower because of such factors as high ore grade, lower taxes, lower wages, government subsidies, and less stringent safety and environmental regulations.

Jan 1, 1982

By Steven J. Schatzel, Joseph Cervik, Gerald L. Finfinger

Gas drainage through surface bore¬holes has been the conventional means of methane control for U.S. longwall gobs. However, these vertical boreholes are becoming so costly, and the surface rights so difficult to obtain, that the Bureau of Mines is developing underground gob gas drainage as an alternate means of methane control for U.S. longwal..ls. Holes are drilled into the roof over the panel and on retreating longwalls, towards the working face from a location inby the face. As the longwall retreats, an increasing portion of the hole inter¬cepts the fracture system over the caved gob. A surface exhauster maintains a vacuum on a pipeline parelleling the panel and draws the methane mixture out of the mine. Auxiliary systems of gob gas drain¬age during longwall mining will be essen¬tial for an increasing number of coal mines. Deep and gassy mines often find ventilation insufficient for adequate dilution of methane in bleeder entries. Although this cross-measure method of degasification has been used successfully in Europe, some of the European tech¬niques cannot be directly applied to U.S. mines. This is the first study of its kind in this country.

Jan 1, 1982

By Manuel Gomez

A computerized, interpolative mapping technique based on the moving average method was shown to be adequate to estimate the between-drill-hole values of coal-seam variables. The forecasting of the spatial distribution of coal properties along the seam was of three kinds: (1) Estimation of the variable of interest on a regional basis from widely spaced sample points, (2) prediction of coal properties for product control from closely spaced data, and (3) prediction of coal properties for specified benches, or layers of the coal seam, from closely spaced sample points. Estimates obtained with the computerized, interpolative mapping procedure were useful in the delineation of seam thickness, elevation, and overburden and in the estimation of sulfur and ash concentrations during the early phases of exploration. This grid interpolation technique was found adequate to adjust between-drill-hole values for trends resulting from the combined effect of several variables on a measured response. This information, coupled with statistical and geologic data that can be obtained in the exploration phase of mining, enlarges the information base available for coal-mine development planning, energy forecasts, and environmental control associated with fossil fuel power generation.

Jan 1, 1972

By Steven J. Schatzel

Gas drainage through surface bore-holes has been the conventional means of methane control for U.S. longwall gobs. However, these vertical boreholes are becoming so costly, and the surface rights so difficult to obtain, that the Bureau of Mines is developing underground gob gas drainage as an alternate means of methane control for U.S. longwalls. Holes are drilled into the roof over the panel and on retreating longwalls, towards the working face from a location inby the face. As the longwall retreats, an increasing portion of the hole intercepts the fracture system over the caved gob. A surface exhauster maintains a vacuum on a pipeline parelleling the panel and draws the methane mixture out of the mine. Auxiliary systems of gob gas drain-age during longwall mining will be essential for an increasing number of coal mines. Deep and gassy mines often find ventilation insufficient for adequate dilution of methane in bleeder entries. Although this cross-measure method of degasification has been used successfully in Europe, some of the European techniques cannot be directly applied to U.S. mines. This is the first study of its kind in this country.

Jan 1, 1982

By Raymond J. Isherwood

The U. S. Bureau of Mines has investigated the domestic primary and secondary lead smelting and refining industries to determine the economic impacts of existing and proposed environmental, health, and safety regulations. The impacts are assessed in terms of capital and operating costs for existing and alternative smelting/ refining technologies. Industry response to regulatory implementation is estimated and quantified in terms of import value from lost lead production. For the primary lead industry, regulatory compliance may add up to 1.15 ¢/lb refined lead to operating cost for rehabilitated plants. Alternative smelting/refining methods could reduce net operating costs by as much as 4.36 ¢/lb refined lead. Capital expenditures would vary from $750 to $1,000 per annual mt of smelter capacity. Secondary lead smelter operating costs would increase about 3.8 ¢/lb refined lead to comply with existing regulations. Capital expenditures would average about $124 per annual mt of smelter capacity. Implementation and enforcement of proposed regulations would result in closure of the primary lead industry and additional expenditures for compliance by the secondary lead industry. Enforcement of the most extreme proposed regulations would force the secondary lead industry to close.

Jan 1, 1988

By Frederick C. Trutt

Research performed on arcing faults and their interaction; with electrical insulating materials within coal.-mine power-system enclosures is described. This work was performed at The Pennsylvania State University from 1 December, 1976 through 30. November, 1977. Results presented are interim in nature and future research is planned to integrate the simulations which have been constructed, as well as to apply developed experimental procedures to the evaluation of electrical insulating materials for use in coal-mine enclosures. The thrust of this research has been divided into several primary areas. These include the development of a theoretical procedure for computation of three-phase and line-to-line arcing fault currents as a function of time, formulation of an arc model based upon thermal-arc plasma properties so that arc voltages and energies may be computed, development of a simulation for pressure and temperature rises when an arc interacts with an electrical insulating material within an enclosure, experimental evaluation of electrical insulating materials in terms of their tendency to support an arc as well as their potential contribution to enclosure pressure rises, and integration of the above research areas to form overall procedures for theoretical and experimental evaluation.

Jan 1, 1977

By Brian T. Brady

The year 1992 recorded unimpressive economic growth and uncertainties over what changes would occur for the financial market. Falling interest rates in the United States and elsewhere tended to exert a number of positive influences on financial markets and, indirectly, the mining and quarrying industry. The interest rate declines during 1992 were no exception. Lower rates prompted many investors to turn their attention to long-term investments such as stocks that offer potentially greater rates of return, causing large cash inflows into the equity market. Lower rates made it easier for businesses to finance growth and for consumers to finance the purchase of products businesses made. Also the rates enabled many companies to increase their health and profitability by refinancing their existing loans at lower rates. Falling interest rates were not confined to the United States. With Japan and Western Europe in the midst of economic slumps, marketing authorities in many countries overseas lowered rates in an effort to stimulate business activity. True to form, that contributed to stock market rallies abroad. Stabilizing inflation and lower interests stimulated the industry during 1992 and will likely influence favorably the industry for the next few years.

Jan 1, 1992

By D. Gearhart

Full-scale tests are conducted on mine roof supports using protocols developed by the National Institute for Occupational Safety and Health (NIOSH) using the unique capabilities of the Mine Roof Simulator (MRS). These protocols simulate the loading conditions that the support will be exposed to in an underground mine to determine the performance capabilities and limitations of the support. Some tests are conducted with rigid boundary conditions, creating uniform contact and near ideal axial loading conditions. These tests are used to determine the ultimate performance potential of a support, including the strength, stiffness, and stability. For prop supports where stability is a critical design issue, tests are implemented to induce buckling by a modified end condition, eccentric contact, or biaxial loading. It is important to determine the cpacity of the support design when the support is subjected to unpredictable loading conditions. This paper examines the effect of end conditions and load profiles on prop support performance and applies a new analysis methodology based on eccentric loading to determine a factor of safety for load capacity. Recommendations for installation practices that minimize eccentricity and therefore preserve capacity are also provided.

By R. P. Vinson

Assessment of workplace exposures is an important tool for helping to minimize dust-related occupational illness and diseases. Real-time particulate monitoring can effectively locate areas where dust controls are needed and determine how well they are working. An affordable, person-wearable, real-time dust monitor is needed. The SKC Inc. Dust Detective (SKCDD) fulfills those requirements (Disclaimer: Mention of any company or product does not imply endorsement by NIOSH). The SKCDD consists of a disposable sampling tube (DST) connected to a small hand-held sampling pump. The SKCDD was developed through a Cooperative Research and Development Agreement (CRADA) between the National Institute of Occupational Safety and Health (NIOSH) and SKC Inc. The relationship of dust concentrations measured by personal gravimetric samplers to those measured by the SKCDD was determined in a laboratory aerosol chamber. A comparison of the means and the relative standard deviation of triplicate measurements of each type of sampling device demonstrated the SKCDD to be a viable alternative means for measuring dust. While it provides accurate measurements for specific coal types, it requires correction factors (those correction factors still need to be calculated) for other coal types.

By John C. Machisak

THIS CHAPTER of the Minerals Yearbook (Volume III) contains overall injury experience for coal mines, both anthracite and bituminous, coke plants, petroleum and natural gas, peat, and asphalt and related bitumens (native); metal mines, their metallurgical plants, including ore-dressing plants and primary nonferrous reduction plants and refineries; nonmetal mines; nonmetal mills; sand and gravel operations; slag (iron blast-furnace) plaints; and stone quarries and their related pants. Volume I of the yearbook contains a chapter showing injury experience and employment data treated separately by metal mines, nonmetal mines, quarries and their related plants, metallurgical plants (ore-dressing plants and primary nonferrous reduction plants and refineries are shown separately), nonmetal mills, sand and gravel plants, and iron blast-furnace slag plants. Volume II contains injury and employment experience in the fuel industries (coal, coke, petroleum and natural gas, asphalt and related bitumens (native), and peat. Injury and employment data are submitted voluntarily for the mineral operations through an industry canvass made by the Bureau of Mines, except for the coal industry, whose reports are mandatory. Information published in this chapter is the result of this canvass. Figures presented in this chapter for 1961 are preliminary except for anthracite, peat, coke, petroleum and natural gas, asphalt and related bitumens, and slag. These preliminary data, with the exception of bituminous coal, are a summation of reports received by May 31, 1962, from the operators showing their injury and employment experience. Estimations of injury and employment experience are not included in these preliminary data.

Jan 1, 1962

By Scott W. Hazen

This report presents the results of a statistical analysis of a limited amount of sample and assay data from a production panel in an open - pit phosphate mine in the Phosphoria formation in Idaho . A frequency distribution analysis is shown for the assays , sample interval lengths , and products of assay and sample interval length for the millshale , furnace - shale , and main phosphate beds . Correlation techniques were used to show the relationships between assays and sample interval lengths . Within- drill - hole and between - drill - hole correlation were also examined as a means of predicting grade trends in the ore . Simulation methods , utilizing a digital computer , were used to establish assay populations that could be used for estimating grade of ore , cutoff grades , and deposit or bed identification .

Jan 1, 1964

By Paul Hatmaker

This paper covers briefly the particular field of dolomite and magnesium limestone; certain uses of high-calcium limestone are mentioned only to show more clearly the limita¬ tions of the magnesian rocks. Such a comparison is helpful because magnesium carbonate is essential for some uses; for others it is immaterial; and for many its presence in an appreciable amount is objectionable. Magnesium carbonate, occurring as a rock resembling limestone or dolomite, is described in United States Bureau of Mines Information Circular 6437, Magnesite. Other com¬ pounds of magnesium are described in United States Bureau of Mines Information Circular 6406, Magnesium Compounds (Other Than Magnesite). Limestone, geologically, is a rock composed essentially of calcium carbonate; commercially, however, the term may include dolomite and magnesium limestone.

Sep 1, 1931

By K. L. Paciorek

The primary objective of this program was to determine the toxic fume and fire hazard of elastomeric noise abatement materials with a limited effort expended on the evaluation of specific treatments applied to mine timbers. Under the conditions employed, for a dimethyl silicone rubber, formaldehyde presented the major toxic threat; acrolein was the main toxic species for both polyester and polyether urethanes and an acrylonitrile-butadiene-styrene resin; in the case of flame-retardant styrene-butadiene rubber compositions, hydrogen chloride, and in the case of PFA-treated timber, furfural, were the major toxic compounds. Of the materials studied, the flame-retardant styrene-butadiene rubbers presented the greatest toxic hazard. The generated data have been reduced to toxic load tabulations amenable to employment for potential hazard assessment.

Jan 1, 1982

By K. R. Farley

A simplified method for the atomic absorption determination of antimony is described. Samples are dissolved in hydrobromic acid and diluted to volume with water. Solutions can be ready for analysis in about 10 minutes and are stable for at least 24 hours. The spectral line at 231 nanometers is used, and there is no effect on absorption resulting .from the presence of any concentration of HBr. Absorbance is linear with antimony concentrations up to 120 micrograms per milliliter. Sensitivity is 1.48 micrograms per milliliter per 0.0044 absorbance. Relative errors on National Bureau of Standards Standard Reference Materials were 3 percent or less, and relative standard deviations on 12 determinations of each of three flue dust samples were 4 percent or less (95-percent confidence limit).

Jan 1, 1980

By J. G. Eisele

Solvent-extraction characteristics of dodecyl phosphoric acid (DDPA) were investigated to determine its potential as a fractional or selective extract-ant for individual elements in a rare-earth-yttrium mixture. The DDPA is an effective extractant for splitting rare-earth mixtures into light and heavy subgroups. Yttrium normally extracts with the heavy rare-earth elements but may be shifted toward an extraction sequence with the light rare-earth elements by increasing the pH. Elements in the light and heavy ends of the rare-earth series can be separated from middle-group rare-earth elements by using diethylenetriaminepentaacetic acid (DTPA) as an aqueous phase counter-extractant. Hydrogen-ion dependency of the distribution coefficients differs from that reported for similar systems at tracer-level concentration.

Jan 1, 1965