Search Documents

By F. du Breuil

BCR National Laboratory (formerly Bituminous Coal Research, Inc.), under a USBM con­tract (originally with the Department of Energy), monitored the installation and operation of a computer-based belt-monitoring and control system at the Barnes & Tucker Coal Co. Mine No. 20, Ebensburg, PA. The system installed was the National Coal Board's Mine Operating System (MINOS) coal transport monitoring and control system. The program objec­tive was to document (1) the installation requirements for a conveyor control system, (2) the operating experience with the system, and (3) the impact of monitoring and control on mine operation. Analysis of the system operation indicates that monitoring and control did improve belt availability significantly, and reduced downtime associated with belt delays. Economic analysis showed the increased belt availability would potentially result in significant production increase, and, therefore, excellent payback on the initial investment. The system performed satisfactorily, was well accepted by the work force, and did not increase the maintenance workload.

Jan 1, 1987

By Jr. Joyce

This report describes sulfatization of nickeliferous laterites from Puerto Rico and the Philippines for recovery of water-soluble nickel and cobalt sulfates. Temperatures ranging from 665 C to 710 C and a 10-percent sulfur dioxide-air reaction gas were employed during batch-roasting tests and during continuous countercurrent treatment in a 2-inch-diameter shaft furnace. A maximum of 69 percent of the nickel and 76 percent of the cobalt were recovered from one sample of Puerto Rican laterite, and a maximum of 96 percent of the nickel and 91 percent of the cobalt were recovered from the Philippine laterite.

Jan 1, 1965

By W. P. Diamond, B. M. Bench, C. M. McCulloch

Coalbeds exhibit a directional permeability, with the maximum permeability oriented parallel to the face cleat. Thus, the most efficient pattern of vertical degasification holes for a coalbed is dependent upon cleat orientation. Surface joints, infrared photolinears, and Ronchi grating photolinears were investigated as potential estimators of subsurface cleat orientation. Cleat orientations were masured in 18 mines, in the Pittsburgh coalbed in southwestern Pennsylvania and northern West Virginia to be used as a standard against which prediction techniques would be evaluated. Two cleat systems with a strong geographic segregation were measured in the study area: N 67° W - N 28° E (95° separation) for the north, and N 76° W - N 17° E (93° separation) for the south. Directional data obtained from the three techniques investigated yielded satisfactory regional predictions of cleat orientation. Analysis of surface joints was the only technique considered sufficiently reliable on a local basis. Prediction of cleat orientation is based on the pairing of the principal directional sets into all reasonable combinations of fundamental systems. The system or systems composed of the most dominant sets nearest to 90° separation are likely to be a reliable prediction of cleat orientation. The most dominant set of the system selected is likely to be the face cleat.

Jan 1, 1976

By R. M. Becker

THIS IS a progress report on a study of the application of statistical practice to mine and mineral sampling undertaken by the Federal Bureau of Mines to provide sound theoretical and practical data for use of the mineral engineering professions. One of the problems in mine sampling is determining the reliability of the results. For certain types of sampling data (random data) the reliability of the results can be stated mathematically. For other types of data there is no known means of quantitatively expressing reliability. In applying measures of reliability to a set of random data, some knowledge or assumption of the characteristics of the particular data is necessary. In many fields these characteristics are well known. However, in mining, where the data are in assays, these characteristics are not well known.

Jan 1, 1961

By K. J. Miller

A two-stage froth flotation technique was developed in the laboratory to separate fine-size pyrite from coal. The process consists of the initial flotation of a 15-percent solids coal slurry with a minimum of frother; the coarse, free pyrite and other refuse are removed in the tailings. The froth product from this first stage is then repulped and treated with a coal depressant, a pyrite promoter, and a frother to float the remaining fine-size pyrite or pyrite attached to coal particles. With the two-stage process, the pyritic sulfur content of a Lower Freeport bed coal sample was reduced from 1.78 percent to 0.75 percent in the first stage, and from 0.75 percent to 0.27 percent in the second stage with good clean coal recovery.

Jan 1, 1972

By M. M. Tilman

The Bureau of Mines conducted research to determine the feasibility of strengthening experimental magnesium-base sheet alloys by strain softening induced by controlled cold rolling followed by selective heat treatment. Relatively small alloying additions having potential for producing strain softening were selected from metals that are readily avail-able. Tensile properties comparable to minimum properties of the most commonly used magnesium-base sheet alloy AZ31B, in the H24 condition (strain-hardened and partially annealed), were obtained in an Mg-IMM (mischmetal)-O.5Mn alloy after strain-softening rolling followed by heat treatment. Tensile properties of the experimental alloys in certain conditions are also compared with minimum tensile properties of other standard magnesium sheet alloys. Incidental to the principal objectives, apparent superplastic behavior was observed in three experimental magnesium-base alloys containing MM, MM plus manganese, and MM plus zirconium.

Jan 1, 1985

By M. J. Ankeny

This is a study of 58 fatal haulage accidents investigated by Federal coal-mine inspectors during the period January - June 1951. The information presented in this circular was obtained by analyzing fatal haulage accidents in 33 bituminous-coal producing counties representing 11 States. The physical conditions represent a cross section off producing coal beds. Mining and transportation methods vary, from those of small hand-loading mines to those of large modern mechanized operations. These data are thought to be representative of haulage conditions within the bituminous-coal mining industry and are submitted to follow up the Information Circular 7604 ?Analysis of Haulage Fatalities in Bituminous-Coal Mines - 1950.? Coal-mine haulage ranks second as a cause of coal-mine fatalities, and the problem of haulage safety is complex. It is subject to constant change and is comprised of numerous influencing variables, which are not always obvious. The solution to this problem will not come through the application of any standard formula or mechanical approach since the inherent factors are strongly influenced by the human equation, and the chain of circumstances is further affected by expediency.

Jan 1, 1951

Confidence in the strength of the U.S. economic recovery was considerably enhanced by third quarter 1983 profits, which showed a 12.8-percent increase over those in the second quarter (table I). Although the increases were not as great as between the first and second quarter of 1983, profits have grown each quarter since fourth quarter 1982. Both total profits and profits per unit of output increased, which the Bureau of Economic Analysis (BEA) attributes to decreases in labor and nonlabor costs (per unit of output), as well as to moderate price increases. [ ] A number of durable goods sectors, however, continue to show profit declines, especially electrical and non-electrical machinery. Profits in the primary metal industry are still negative, but the economic picture of this industry is improving. Between the second and third quarters of 1983, capacity utilization increased somewhat in primary metal manufacturing and stone and earth mineral mining but did not change at all in metal mining. Capacity utilization in metal materials increased from 47.4 percent in the fourth quarter of 1982 to 64.2 percent in the third quarter of 1983 (table 2).

Jan 1, 1983

By R. S. Dean

This report, the second of a series of annual reports of the Metallurgical Division to be released in this form covers the fiscal year July 1, 1935, to June 30, 1936. The technological work of the division is performed by sections. Thus, an efficient organization is provided to prosecute the various problems under investigation, and a logical system is set up for presenting the material contained in this report.

Jan 1, 1937

By J. B. Carman

This paper, describing the concentrator of the Molybdenum Corporation of America in Taos County, northern New Mexico. 7 miles east of Questa, is one of a series on milling methods being prepared for and published by the United States Bureau of Mines. The mine from which the ore comes is 1 1/4 miles from the mill, and produces about 40 tons of ore per day by the cut-and-fill method.3 The ore contains about 5 per cent of MoS2. The mill has a capacity of 50 tons of ore per day and utilizes flotation methods. Water is taken from Red River. Power is generated by a water wheel, or by a Diesel engine in times of water shortage during the winter. The mill is located close to the bottom of a canyon, in order to obtain maximum head or, the water wheel, and the flow of ore is therefore maintained partly by gravity and partly by an elevator and pumps. ORE TREATED The MoS2 content of the concentrator feed ranges from 4.5 to 7.5 biotite, fluorite, small amounts of rhodochrosite and calcite, and the minerals of the granodiorite country rock.

Jan 1, 1932

By Richard F. Link

The objective of this report is to explain a statistical method for the summarization, organization, and classification of multivariate assay and other data from the mineral industry. Multivariate data are those characterized by several measurements at each data point, such as assay data from a mixed metal mine, or blast furnace data. A specific method of linear discriminant analysis, the Mahalanobis d2 procedure, is explained, starting from elementary principles; the d2 procedure enables many measurements at many data points to be studied by investigating the interrelationships among the data. The relation of linear discriminant analysis to other statistical methods for treating multivariate data, in particular the eigenvalue technique of factor analysis, is also explained. Example analyses are made on data from the Frisco mine, San Francisco del Oro, Chihuahua, Mexico. The data comprise assay values for silver, lead, copper, and zinc taken at some 19,000 sample points distributed into 91 groups.

Jan 1, 1967

By T. F. Mitchell, B. K. Shibler, J. V. Batty, W. G. Sandell, G. M. Potter

"INTRODUCTION The Park City district, situated 30 miles east of Salt Lake City, Utah, in the Wasatch Mountains, Is a well-known producer of lead, zinc, and precious metals. Nearly continuous production has been maintained from the dis¬trict since its early discovery about 1870. For approximately 50 years, gravity milling methods were employed to beneficiate Park City ore, and during that time tailings from the mills were sluiced down Silver Creek and deposited on lands below the camp for 7 miles.Owing to the large tonnage of tailings deposited along Silver Creek, considerable work was done in the past in the attempt to develop a low-cost concentration method for re-treating this material, but no-method was found that was economically feasible. The Bureau of Mines was asked to conduct beneficiation tests on Park City tailings in November 1944, and metallurgical studies were initiated at that time. This report summarizes the results of laboratory ore-dressing studies made on samples from the Grasselli deposit."

Dec 1, 1947

By Oliver C. Ralston

Fluorescence is of growing interest to the mineral industry because certain minerals may be detected thereby and because, as shown in figure 1,4/ many minerals (natural or synthetic) are needed in tubes and lamps. The use of fluorescent lighting is expanding, and large numbers of lamps of many sizes and shapes are being made and used in works, factories, stores, offices, homes, and in photography. Fluorescent tubes, as distinguished from clear tubes filled with neon, argon, or other rare gases through which a current of electricity passes, fluoresce owing to specially, selected and prepared minerals placed in the tubes. Luminous chemicals and paints also contain special minerals and are used in similar applications; therefore, these also will be considered in this report. Although the quantity of minerals (in tons) that are used for fluorescent purposes is small, and probably will continue to be so, this use is significant because it exemplifies a requirement for "pure" minerals in which a trace of contaminant as" minute" as one part in ten million may distinguish between the acceptance or rejection of a particular material. This extreme purity makes synthetic minerals almost essential, and natural mineral's are now little used.

Jan 1, 1944

By K. A. Fowler, L. W. Higley

Steels with an alloying addition of depleted uranium were studied to develop successful melting , casting , and fabricating methods ; to obtain data on mechanical properties ; and to determine the effects of this alloying element . Uranium in amounts up to 1.5 percent was added to steel - base compositions containing approximately 0.5 percent carbon , 2 percent nickel , 0.25 to 2.0 percent silicon , and 0.75 percent manganese in both vacuum- melted and air -melted heats . Radiation levels were monitored for all operations . Bureau of Mines research at the Rolla Metallurgy Research Center showed that uranium additions did not increase tensile strength ; that hot - shortness occurred during forging above 1,090 ° C because of the presence of a low melting point constituent of a eutectic type ; and although a measurable amount of radioactive contamination resulted from processing , the quantity was never large enough to require the work area to be identified as a radiation area .

Jan 1, 1964

By L. G. Trudell, J. W. Smith, K. E. Stanfield

Representation of actual oil yields from sections of the Green River formation oil shales by two types of drill - cutting samples was evaluated . Average oil yields of single sets of mud cuttings from hydraulic rotary drilling in Colorado and gas cuttings from pneumatic rotary drilling in Utah were compared statistically with yields of core samples taken from adjacent holes . Oil yields from gas cuttings were identical to oil yields of core samples . Mud cuttings appeared to represent a section of the formation conservatively , the deficiencies increasing with increasing richness of sample . Because a large amount of the oil - yield data currently available for the Green River formation is based on mud- cutting samples , development of a valid correction method by additional testing is needed .

Jan 1, 1963

By Robert S. Becker

The results of a laboratory investigation of coal cutting mechanics and noise is presented. These experiments were performed using a linear cutting apparatus that operates over a broad cutting speed range. The influence of several coal cutting parameters on the noise, force, productivity, and specific energy associated with linear cuts is ascertained. Some basic theoretical aspects of coal cutting mechanics and noise generation are discussed, and the results of the laboratory experiments are used to Formulate analytical models of the coal cutting forces and noise. The analytical model For coal cutting noise is then generalized to account for the more important effects of rotary cutting. Based on the generalized model, an estimate of the sound pressure level at an operator's position is made for a typical continuous mining machine. It is concluded that by employing linear rather than rotary cuts, using deeper depths of cut, slower cutting speeds, and more efficient cutting tools, it is possible to reduce the level of coal cutting noise, as well as Provide benefits to other important areas of underground health and safety.

Jan 1, 1980

By D. L. Forrester

This paper, describing the milling practice of the Old Dominion Co., is one of a series being prepared by the: United Staten Bureau of Mines. ACKNOWLEDGMENT In the preparation f this paper, acknowledgment is made of the valuable service rendered by R. S. Allen, metallurgist of the Old Dominion Co. T. G. Chapman, one f the consulting engineers of the Bureau of Mines, assisted in arranging the paper for publication.

Jan 1, 1931

By T. Muldoon

Literature review and extensive field survey of line and check curtain materials and practices showed: ? Miners, in general, know how to set tight curtains, and do so when needed. ? The tradeoff is economic; tight ventilation is labor-intensive. Line and check curtain techniques found are catalogued and evaluated. A fieldworthy 10 ft extensible brattice to maintain a 10 ft setback was found in use in two mines on continuous miner faces. This technique was evaluated in the laboratory for leakage and methane control at the face. Significant results include: 1) Air leakage through a gap in the extensible curtain depends upon the ratio of the cross-sectional areas between entry and return as well as gap area; 2) Gap shape has no significant effect on methane concentrations at the face -increasing gap area diminishes ventilation effectivness; and 3) Substantial reductions of CH4 concentrations at the face were accomplished by brattice extensions with gaps of up to 5 ft2 in area. An "inby hook," inserted in the roof automatically to make possible the deployment of a longer (20 ft) brattice extension in the context of a remotely controlled miner, was tested in various roof types. Insertion of this design succeeded only in coal.

Jan 1, 1982

By Frank E. Chase, John Rusnak, David Newman

During the past quarter century, coal mine geologists have evolved from providing a qualitative description of drill core and coal reserves into quantitative geotechnical specialists who bridge the gap between geology and engineering. In the late 1970’s and early 1980’s, hazard prediction mapping was in its infancy. At best, hazard maps identified rudimentary structures and conditions such as stream valley locations, sandstone/shale transition zones, and lineaments. A “technical disconnect” had existed between geologists and mining engineers as each profession operated largely independent of each other. Engineers did not readily integrate geology and geologic conditions, with the exception of coal thickness, into mine planning. Geologists were relied upon for reserve estimates and did not participate in mine planning or design. The employment and market slump of the 1980’s and 1990’s combined with mining more challenging reserves mandated that this gap be bridged and forced geologists to learn to speak more “numerically” to engineers so they could be understood. The purpose of this paper is to describe the procedures and thought processes used by coal mine geologists when determining various mineability and reserve extraction feasibility issues. The paper will also address underground geologic hazard mapping and prediction techniques. To achieve these objectives, the opinions and experiences of leading coal mine geologists, geotechnical and strata control specialists across the United States were solicited.

By William G. Pariseau

A small displacement-small strain finite element technique utilizing the constant strain triangle and incremental constitutive equations for elastic-plastic media that are nonhardening and obey a Coulomb yield condition has been applied to the analysis of gravity flow initiation in a V-shaped hopper containing a powder under lunar environmental conditions. Three methods of loading were examined. Of the three, the method of computing the initial state of stress in a filled hopper prior to drawdown by adding material to the hopper layer-by-layer is superior (as expected). Results of the analysis of a typical hopper problem show that the initial state of stress, the elastic moduli, and the strength parameters have an important influence on material response subsequent to the opening of the hopper outlet.

Jan 1, 1971