Search Documents

Coal-bearing beds underlie 23,000 square miles, about one third of Missouri's total area. Twelve out of more than twenty named coal seams have been or are being commercially mined. The remainder are too thin for commercial production. The coal is high volatile bituminous, with reserves estimated to be six billion tons, 1.24percent of U.S. coal reserves. Coal-bearing strata are generally thin seams which can be up to five feet thick. Typically, mined seams are about 28 inches thick. Coal deposits were first mined in Missouri in the 1840s, with the coal used primarily for domestic heating and blacksmithing. Production increased with the introduction of steamboats on the Mississippi. Coal production in 19 17 was six million tons. Production has steadily declined from a high of nearly seven million tons in 1984 to 2.3 million tons in 1991. Declining production is the result of several factors, including competition from other energy sources and the high sulfur content of Missouri coal. Today, coal-fired electric generating plants are the biggest consumers of Missouri coal. The Missouri regulatory program was conditionally approved November 21,1980, and fully approved January 17,1983. Its Abandoned Mine Land program was approved January 29, 1982.

Jan 1, 1992

By W. D. Bensema, J. W. Adams

A portable, multichannel battery-operated mine-permissible measurement system was developed to measure the rms magnetic-field noise spectrum in the frequency range from 100 Hz to 375 kHz. During each measurement, the entire spectrum is measured simultaneously through the use of time-domain recordings which are later analyzed by Fast Fourier Transform processing. Dynamic ranges of 60 dB in a 125 Hz bandwidth are obtained for spectra covering the range from 100 Hz to 100 kHz. The method also allows a three-dimensional display of the way spectrum occupancy changes with time. Calibration and correction procedures allow absolute field strength measurement with an uncertainty of not more than 3 dB. We feel that further analysis of the system errors will allow this uncertainty to be reduced to less than 1 dB. Ambient magnetic field noise spectra covering frequencies from 100 Hz to 100 kHz are given for several underground coal mine locations. Examples are also given of magnetic field noise on the surface above the mine, noise in the mine face area, noise radiated by specific equipment, the voltage spectrum found on a 600 V dc trolley wire, and noise picked up simultaneously on loops and on roof support bolts.

Jan 1, 1973

By John L. Reuss

A laboratory study was conducted by the Bureau of Mines to investigate the technical feasibility of decomposing hydrous magnesium chlorides by using a steam pyrohydrolysis technique. This procedure consisted of injecting steam into the atmosphere of a decomposition furnace containing samples of hydrous magnesium chloride and determining the rate of hydrolysis by measuring the rate of chloride evolution. The variables investigated were temperature, amount of water vapor in the decomposition atmosphere, and hydration stage of magnesium chloride. The application of steam was shown to accelerate both the rate and completeness of magnesium chloride decomposition reactions. For example, when magnesium chloride hexahydrate is exposed to a furnace temperature of 600' C in an air atmosphere for 20 minutes, the decomposition is 37 percent. Under identical conditions in a steam atmosphere, the decomposition is in excess of 70 percent. The magnesium oxide produced by the steam pyrohydrolysis of magnesium chloride dihydrate at 800° C contained 98 percent magnesium oxide. Based on magnesium oxide composition, this is equivalent to that of burned magnesite produced at temperatures in excess of 1,300° C. To demonstrate the quality of the product on a practical basis, metal reduction tests have shown it to be equivalent to reagent-grade magnesium oxide as a carbothermic reduction feed material.

Jan 1, 1974

The instrumentation specification in the National Academy of Engineering (NAE) report of March, 1970, set forth some rather general guidelines that the seismic surface system should follow. The fact that there was no comparable equipment in existence at that time, and the need to produce a system from presently available equipment, was spelled out in that document. The features that the system should include were listed, and included: • Quick and simple deployment • Portability • Battery-powered operation • All-weather operation • Computational simplicity and speed • High reliability and long shelf-life • Dual service for location and communication • Adaptability to widely varying seismic velocities. topography, and geologic structures • Minimum maintenance • Capability of continuous operation for extended periods, and • Reasonable cost Since that report, there has been a substantial amount of field work addressing the trapped miner detection and location problem carried out by Westinghouse Corporation under contract with the Bureau of Mines. Two complete surface systems have been designed, built, and field tested and substantial documentation has been produced on the mine environment and background noise using these systems. These systems, built from off-the-shelf equipment, have been designed with maximum flexibility in mind in order to explore what con¬figuration a field unit should have.

Jan 1, 1974

By Stephen C. Tadolini, Thomas M. Barczak

Roof support systems, longwall shields in particular, have persistently grown in size and capacity for the past 25 years. Why is this? Is it a good thing or is it unnecessary? What are the consequences of this “bigger-the-better” design philosophy? Rarely do we see a “one size fits all” approach to roof support except when it comes to longwall shields, where the historical trend for new procurements is to simply purchase the highest capacity support you can buy. Does high capacity ensure failures will not occur? The answer is no! The highest capacity tailgate supports are typically the ones that fail the most often. What does this tell us? It tells us that there are fundamental aspects of support design and ground control that we still do not understand or recognize when designing a support system. This paper provides an interesting evaluation of these issues and proposes a different approach to support design that attempts to match the support performance characteristics to the ground behavior. Along the way, some of the old premises of support design will be discarded, and new “controversial” ideas developed. Thinking outside the box never hurt any industry. Mining has made it a common practice.

By T. G. Carnahan

The Bureau of Mines conducted laboratory-scale weathering research on a leach residue containing elemental sulfur and mixed metal sulfides. Experiments were performed to determine pH and impurity element concentrations in the effluents as functions of time and to determine the effects on effluent concentrations of mixing the residue with dolomite tailing material. Four 800-day tests were conducted simultaneously. Soluble metal concentrations, especially zinc and copper, were excessive in the effluents from washed and unwashed samples of the residue. Concentrations of up to 20 g/l of Zn and 12 g/l of Cu were obtained. The pH values of the unwashed and washed residue effluents at the completion of the experiments were 2.8 and 1.9, respectively. Sulfuric acid from oxidation of pyrite caused the pH decrease. Mixing unwashed residue with dolomite tailing to maintain a near-neutral pH minimized the heavy metals content in the effluents. The pH in the dolomite tests increased slowly after the first 360 days and attained values of 7.8 and 8.2, respectively, for tailing containing 1 pct leach residue and for tailing devoid of leach residue. Dissolved zinc and copper did not exceed 0.10 g/l of Zn and 0.001 g/l of Cu.

Jan 1, 1982

Aid mine operators as well as mine inspectors in making quick but sufficiently accurate measurements of the rock dust content of coal/rock dust mixtures. The Problem Past research has shown that accumulations of volatile coal dust in underground coal mines can be rendered non-explosive by dilution with chemically inert rock dust (usually limestone). Consequently, rock dusting is required by law in U.S. underground coal mines. However, mine officials and inspectors have no quick and reliable means to determine whether enough rock dust has been applied to achieve a mixture that is in compliance with the law. Even the compliance tests used by the Mine Safety and Health Administration (MSHA) are slow and involved. MSHA assures that a mine has been rock dusted adequately by collecting samples from rock dusted areas of the mine and sending the samples to a laboratory for analyses of the inert-dust content. The analyses may not be completed for more than two weeks, during which time the mine in question might be inadequately protected against coal dust explosions. To solve this problem, the Bureau of Mines devised a quick, simple and reliable device that can immediately determine the rock-dust content of a mixture of coal and rock dust.

Jan 1, 1985

By Jami M. Girard

INTRODUCTION Slope stability accidents are one of the leading causes of fatalities at U.S. surface mining operations. The Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) is currently conducting research to reduce the fatalities associated with slope failures and other unexpected failures of ground. The purpose of this paper is to introduce various warning signs of slope instability so operators are better able to recognize hazards. The most common slope monitoring equipment and practical methods of installation are discussed as well as the limitations of these systems. CONSEQUENCES OF SLOPE FAILURES Unexpected movement of ground causes the potential to endanger lives, demolish equipment, or destroy property. Between 1995 and 2001 (2nd quarter), 34 fatalities were caused by ground instability. This accounts for approximately 15% of all surface mine fatalities (Figure 1). These figures include fatalities classified by the Mine Safety and Health Administration (MSHA) as “fall of face or highwall,” “powered haulage,” “equipment,” and other MSHA accident categories, where the primary cause of the accident was unanticipated movement of the ground. This includes fatalities resulting from bench and highwall failures, rock falls, waste dump and stockpile failures, and the collapse of unknown underground workings. [ ]

By Lloyd A. Morley, Robert Stefanko

Before going directly to the analysis, it would be good to summar¬ize explosion-proof container approval methods. Both Magison (52) and Short (84) state that in general practice, the systems are certified for: 1. a rugged enclosure able to withstand an internal explosion but not allow explosively hot gases to escape, and 2. maximum surface temperature, with equipment operating inside, that will not ignite the surrounding atmosphere. Also, testing insures that any material in contact with the container surface will not be ignited by a hot spot. Associated with the first practice, the enclosures are inspected for: 1. a safe flange gap width, 2. a pressure increase during ignition, and 3. an hydrostatic pressure withstand level. The hydrostatic pressure level is almost always determined by a meas¬ured ignition-pressure test and is usually applied to prove the mechan¬ical design to some safety factor. Consequently, explosion-proof enclosure testing includes temper¬ature, permissible flame gap, and pressure. Specifications and prev¬ious research also can be similarly separated even though some interre¬lation exists between the flame gap size and internal enclosure pressure during an explosion. The Schedule 2G Sections applicable to these subjects are: 1. 18.2 Definitions; 2. 18.6 Applications;

Jan 1, 1974

Provide reasonably priced, reliable fire protection for AN-FO haulers. Approach An automatic fire sensing and suppression system for AN-FO haulers was developed and on-vehicle tested. How It Works The system works in two ways to protect personnel from dangerous and unpredictable AN-FO fires. First the system senses and suppresses fires on the truck before they spread to the AN-FO in the bunker. This design was chosen because AN-FO truck fires generally start when combustible liquids (such as diesel fuel, hydraulic fluid or lubricating oils) are ignited by hot surfaces mainly on three areas: the engine, the transmission or the power take-off. These fires are quickly sensed by a linear temperature sensor strung throughout these three areas. The system then warns the operator and automatically suppresses the fire by discharging 30 pounds of multipurpose dry chemical extinguishing agent through a network of fixed hoses and nozzles. Second, this system includes six spot thermal sensors mounted inside the bunker on the truck to monitor the AN-FO temperature in case a fire does spread to the bunker area. If the bunker temperature rises to 190° F, a loud siren is sounded to warn nearby per-

Jan 1, 1981

By Jeran Paul W., Michael A. Trevits

Subsidence data gathered by the U.S. Bureau of Mines over a series of longwall panels in the Pittsburgh Coalbed were studied to obtain insight as to the role of time in the subsidence process. It was found that subsidence began essentially with undermining and was completed within 1 year. The progress of the subsidence was dependent upon location above the panel. Subsidence in the central area of the subsidence trough, where subsidence is the greatest, was about 90 pct complete by the time the face had progressed a distance equal to one overburden thickness beyond a particular surface point. For a point over the rib of the longwall panel, the subsidence was only about 60 pct complete at this time. Data from three other sites in the northern Appalachian Coal Basin were analyzed to determine if an anomaly or the true characteristics of the subsidence process had been observed. All sites behaved similarly in the central portion of the subsidence trough. However, the subsidence of points over and adjacent to the ribs of the longwall panels was site specific. The fact that movement across the width of the panel was not uniform should be taken into account in assessing damages or the potential for damages resulting from mining-induced subsidence.

Jan 1, 1995

By J. J. Cummins

Green River oil shale previously extracted by benzene was heated at 150°, 200°, 250°, 300°, and 350° C for 0.5 to 360 days to determine the rate at which kerogen degrades to thermal products, the types of thermal products formed, and the effect of prolonged low-temperature heating (preheating) upon subsequent assay yields. Thermal decomposition of kerogen at 150° to 350° C is treated as a first-order reaction. The specific reaction rate for kerogen decomposition increases from 2.2 X 10-4 per day at 150° C to 2.0 X 10-1 per day at 350° C. The calculated kerogen activation energy is 19 kcal. Variations in the rate of formation of individual type components of the pyrolytic products were found. Carbon balances show an increase in the amount of kerogen converted to bitumen and oil (from assay of preheated oil shale) as the temperature of preheating increased from 150° to 350° C. Total product from shale preheated at temperatures of 150° and 200° C gave less than 100 percent of Fischer assay yields while the total products from shale preheated at temperatures of 250° to 350° C gave greater than 100 percent of Fischer assay yields.

Jan 1, 1972

By Robert F. Chaiken

A novel approach to eliminating environmental and public safety hazards that are associated with fires in abandoned coal mines and waste banks involves the use of in situ combustion technology developed by the Federal Bureau of Mines to accelerate the burning of the wasted coals in place. This technology would be used under exhaust ventilation control conditions that would allow for total management of the hot gases produced. Combustion stoichiometries would be optimized to minimize unburnt combustibles and to maximize the heat content of the gas products, which will be exhausted at one or more fan locations. When necessary, scrubber systems would be employed to remove air pollutants, such as sulfur dioxide; heat utilization systems (process heat, steam, and electricity) would also be employed to offset operational costs. Ultimately, complete burnout would solve the fire and acid water formation problems of the abandoned coal mine or waste bank. Pertinent technical data for burnout control are derived and discussed in terms of the important material and operational parameters. In general, it is believed feasible to operate a burnout system in an existing abandoned mine or waste bank fire at thermal power levels in the range of 10 to 100 Mw, and at exhaust gas temperatures of 1,000° C (1,830° F).

Jan 1, 1980

By T. H. Jeffers

Significant amounts of cobalt are present in readily accessible spent copper leach solutions. The Bureau of Mines investigated the feasibility of extracting cobalt from these solutions in a multiple-compartment ion-exchange (MCIX) column. The effects of aqueous flow rate, resin flow rate, column height, and compartment height on cobalt extraction were determined. Cobalt extractions of 92 pct or higher were achieved at solution flow rates of up to 5.5 gpm/ft of column cross-sectional area and an aqueous-to-resin flow ratio of 40:1. Overall cobalt extraction increased as the column height increased, but cobalt extraction per unit of length was more efficient in 8-and 12-ftco1umns than in an 18-ft column. Solvent extraction procedures were utilized to purify and concentrate the MCIX column eluates and produce a cobalt sulfate solution containing 70 to 80 giL Co. Metallic cathodes containing over 99 pct Co were e1ectrowon from this solution. Zinc, nickel, and copper byproducts were also recovered during processing of the ion-exchange eluates. Estimated total capital cost for a commercial-scale 10,000 gpm of a spent leach solution containing 26 million. With credits for zinc, nickel, and copper estimated net operating cost was $9.36/lb Co.

Jan 1, 1987

By Kenneth L. Cashddollar, Terry G. Montgomery, Eric S. Weiss, John E. Going

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research on dust explosions by studying post-explosion dust samples. The samples were collected after full-scale explosions at the PRI, Lake Lynn Experimental Mine and after laboratory explosions in the PRL 20-L chamber and the Fike 1-m3 chamber. The dusts studied included both high and low volatile bituminous coals. Low temperature ashing for 24 hr at 515°C was used to measure the incombustible content of the dust before and after the explosions. The data showed that the post-explosion incombustible content was always as high as or higher than the initial incombustible content. The MSHA alcohol coking test -was used to determine the amount of coked dust in the post-explosion samples. The results showed that almost all coal dust that was suspended within the explosion flame produced significant amounts of coke. Measurements of floor dust concentrations after LLEM explosions were compared to the initial dust loadings to determine the transport distance of dust during an explosion. All of these data will be useful in future forensic investigations of accidental dust explosions in coal mines or elsewhere.

By R. C. Gabler

Laboratory tests on a combined nitrogen roast--two-stage leach--electro-winning approach show promise as a possible process for recovering copper, sulfur, iron oxide, and valuable minor metals (gold, silver, and molybdenum) with a minimum impact on the environment. During the nitrogen roast at 800° C, 15 to 20 percent of the sulfur together with a significant fraction of the volatile elements, such as arsenic, bismuth, lead, and zinc, are removed from the chalcopyrite concentrate. The resulting calcine, consisting of 8-chalcopyrite, troilite, and a bornitelike structure, is leached with hydro-chloric acid to remove 70 to 85 percent of the iron. The digenite in the leach residue is dissolved in an oxygen-saturated, spent sulfate electrolyte. Using a graphite 'anode plus sulfur dioxide to reduce interference from ferric iron, copper of 99.99+ purity is electrowon at current efficiencies of 88 to 92 percent and a cell voltage of 0.4 to 0.5 volt. Copper recovery for the overall process is 98 to 99 percent. Sulfur is obtained in the elemental form from the roasting and leaching steps. Iron can be recovered from the hydro-chloric acid leach solution. Gold, silver, and molybdenum are concentrated in the silica residue from the spent electrolyte leach.

Jan 1, 1975

By Ivette E. Torres

Of the 15 selected non fuel mineral commodities detailed in table 12, only 3 indicated increases in worldwide consumption in 1992. As in 1991, decline in consumption levels of the selected commodities can be attributed to reduced levels of use in the former U.S.S.R. and Eastern Europe. Of the remaining 12 commodities, 2 magnesium and cadmium, stayed relatively the same, while the other 10, including iron and steel, all recorded decreases. Global consumption of iron ore is estimated to have fallen about 3.5 % or about 30 million tons. This is a greater decline than what was estimated for production of iron ore, which is down only 2.7% or nearly 26.5 million tons, suggesting an addition to stocks. The consumption trend for iron and steel has been declining since 1989. This has mainly been due to the continued drops in use in the former U.S.S.R. and Eastern Europe. Even as the European economy begins to turn upward, there may only be a slight increase in consumption of iron, steel, and cement, considering the high cost of construction needed to modernize factories and buildings in Eastern Europe. Many feel that the economies of these countries are limited by the current status of their industries.

Jan 1, 1994

By J. Douglas Causey

In 1987, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied 11,069-acres of the 12,290-acre Eldorado Wilderness Study Area (NV-050-423) in order to evaluate its identified mineral resources. The study area is located in Clark County, NV, adjacent to and northeast of the town of Nelson. There are inferred subeconomic resources on the Paul (gold, silver), Bel (gold, silver), Big Horn-Inez (silver, copper, lead, zinc) claims, and Montezuma (gold, silver, copper, lead, zinc) patented claim group in the Eldorado study area. Because of lack of exposures, tonnage and grade on these properties could not be determined. No resources were identified for the other five properties examined in the area. The southern two-thirds of the area is in the Eldorado mining district, a base- and precious-metal district which has been intensely explored for over 100 years. Nine claim groups were examined in the study area. Eight claim groups are within the Eldorado district and include the Montezuma (patented -M.S. 3966), Bel, Eldorado, VAR, SINJUN, Paul, Rusty Bit, and Big Horn-Inez. One property, the Flintstone claim group, is north of the Eldorado mining district at the north end of the study area.

Jan 1, 1988

By Kenneth H. Johnston

Information on oil and water production, volume of water injected, core analyses, and well completion data was collected on 28 Red Fork sand water-flood projects for comparison and evaluation of results. An average water injection efficiency of 35 percent, an average water-injected to oil-produced ratio of 16.8:1, and an average loss outside the flood pattern of approximately 45 percent of the injected fluid resulted in an oil recovery to January 1, 1969, of only 5.6 percent of the pore volume, or 9.1 percent of the initial stock-tank oil in place. The principal causes of poor oil recovery from these projects are the losses of large quantities of injection water from the flood patterns through oriented, natural fracture systems or zones of high permeability and excessive channeling of injection fluids from input wells to oil wells. For more efficient operation and a higher percentage of oil recovery from the Red Fork sand and other low-permeability-sand waterflood projects, directional orientation of both induced-and natural-fracture systems should be determined during early development. The success of a low-permeability-sand waterflood project depends to a large extent upon the orientation of the injection wells with the fracture system.

Jan 1, 1970

By L. L. Oden

The Bureau of Mines analyzed vapor-aluminum-diffused stainless steels prior to conducting corrosion measurements in severely sulfidizing environments. These studies were conducted in response to the national need to better control the environmental and economic costs of corrosion. Specimens of a ferritic alloy and austenitic alloys types 316 and 310 were treated by a proprietary vapor-aluminum diffusion process and a dual vapor-aluminum diffusion process. Weights and dimensions were recorded before and after treatment, and comprehensive metallographic, X-ray, and electron micro-probe analyses were conducted for both single-and dual-vapor-aluminum-diffused specimens. Surface aluminum concentrations ranged from 26 to 34 wt-pct for all alloys. Dual treatment increased the quantity of aluminum per unit area by a factor of 2 and increased the depth of penetration by a factor of 3. The aluminum-diffused region of the ferritic alloy was single-phase aFe solid solution that was ordered on the surface, whereas two distinct diffusion layers were ob-served on the austenitic alloys. The outer layer comprised aFe solid solution that was ordered on the surface, and the inner layer was a two-phase mixture of aFe solid solution and the interrnetallic compound AINi.

Jan 1, 1982