Search Documents

By Arne Landsberg

The Bureau of Mines measured the vapor pressure of FeC12 , FeBr2, FeI2, Sb, Bi, Cd, Mg, Pb, FeC13 , and VCl2 using the Knudsen-and torsion-effusion methods, and on FeC13 -NaC1 mixtures, Au2Cl6, and MgNi2 using only the Knudsen method. Apparent vapor pressures calculated from the experimental data vary with orifice size and method of determination. Reaction with residual oxygen in the instruments was noted to have an effect on the iron halide data. Vapor pressure curves plotted as log P versus 1/T (where P is pressure and T is absolute temperature) for one substance using several orifice sizes tended to converge at a single point when extrapolated beyond the experimental region. All of the data, except those of VC12, agree with previously published results. The importance of comparing effusion measurements with those obtained by other methods and the variations encountered with various orifice sizes are discussed.

Jan 1, 1977

At the end of August, U.S. producer posting of 99.5 percent unalloyed aluminum had been established at 48¢ per pound. At that time, dealer-quoted unalloyed ingot was reportedly at 44¢-47¢. CADMIUM: By late August, most U.S. producers had raised cadmium selling prices by 25¢ to $3 per pound. As a consequence, dealer quoting of cadmium ranged from $2.95 to $3.05 per pound. COAL: The wildcat strike, which began in southern West Virginia on July 19 and eventually spread to nine other States before ending on August 13, at its peak, idled approximately 115,000 miners and accounted for daily coal losses of an estimated 1.5 million tons at the height of the work stoppage. Concerned about the effects of the production cutbacks, the Bureau of Mines, early in the strike period, initiated its coal strike monitoring system which it had developed during the prolonged coal strike in the fall of 1974.

Jan 1, 1976

By J. R. Thoenen

This circular is part 2 of the third subject (entitled "Excavation") of a series summarizing; the technical problems involved in the production and preparation of sand and gravel. Part 1 discussed the use of power shovels, draglines, and excavator cranes. This paper discusses the use of the power scraper, slackline cableway excavator, and hydraulic monitor, and part 3 will discuss the use of various types of dredges. Subsequent papers in the series will discuss the use of haulage equipment, the application of both excavating and haulage equipment to various types of deposits, and operating costs. THE POWER SCRAPER The power scraper is a younger member of the various forms of gravel excavators. It is a mechanized enlargement of the slip scraper and other scrapers which depend upon animals for power and has a greater range of operation from a single set-up than any other excavation unit except the slackline cableway excavator.

Jan 1, 1935

By Harry R. Nicholls

Six different chemical explosives were detonated in a test series to com-pare their relative performance in granite. From 5 to 255 feet from the detonation point, strain, acceleration, and particle velocity were recorded and analyzed for amplitude and pulse shape. Strain energy was calculated from strain data, and displacement data were obtained from particle velocity data by integration. The results show that explosives which have a characteristic impedance more closely matching that of the rock generate larger peak amplitudes than explosives with a lower characteristic impedance. The results also show that as the ratio of characteristic impedance of exp1osive-to-rock approaches unity, more rock is crushed and a larger percentage of the avail-able explosive energy is transferred to the rock as seismic energy. The effect of characteristic impedance is shown to be greater than the effect predicted from acoustic theory and is believed to be indicative of shock wave effects at the explosive-rock boundary.

Jan 1, 1965

By J. M. Kuchta

Experimental data are presented on the autoignition temperature (AIT) characteristics of the hydrocarbon jet fuel, JP-6, in various oxygen-nitrogen atmospheres under conditions of constant volume and constant pressure. AIT's of this fuel in air varied little with fuel injection pressure but increased greatly with decreasing fuel content at low fuel-air-ratios. They also increased with decreasing oxygen content of the fuel vapor-oxidant atmosphere. Consistent with thermal ignition theory, the ignition temperatures increased with decreasing initial pressure, ignition delay, and vessel radius; expressions are given which define the observed variation of AIT with these variables for JP-6 fuel vapor-air mixtures. The significance of autoignition temperature data obtained using various ignition criteria is discussed to show the usefulness of such data in evaluating fire and explosion hazards. In addition, data are presented on the extent of oxidation that occurs prior to autoignition of this fuel in air at various temperatures.

Jan 1, 1965

By R. E. Coleman

The molecular species occurring at the mineral-reagent interface of the galena-aqueous potassium ethyl xanthate system was studied by developing a technique for using an attenuated reflection method in conjunction with standard infrared spectroscopy procedures. Lead ethyl xanthate was detected from the infrared spectra of all galena surfaces treated in the pH range of 7 to 11. At pH 8.5, lead ethyl xanthate formed as a film chemically bonded to the galena surface. A solvent extraction sampling method was employed with infrared spectroscopy to obtain quantitative data on the lead ethyl xanthate removed from the galena surface. The data showed that between pH 7 and 11 thy quantity of lead ethyl xanthate physically adsorbed decreased as the pH was decreased; in the same pH range, the quantity of free lad ethyl xanthate in the aqueous medium remained constant, and the amount of unreacted xanthate varied.

Jan 1, 1966

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries . This interpretation of the laws of Japan has been prepared from the best available information in Washington but is released subject to correction and amplification , if necessary , by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State . It is based on the law and regulations of 1905 as revised in December , 1915 , and translated by J. de Becker , LL.B. Occasional words and phrases quoted herein are accordingly taken from this translation and have not been checked against the original . The references are to the law ( as distinguished from the regulations ) unless otherwise stated .

Jul 1, 1930

By G. E. Rennick

A siphon-type laboratory airlift well was designed and operated by the Bureau of Mines to study the concurrent flow of air and oil in small-diameter pipes. Glass flowstrings ranging from to 1 inch in diameter and from L4 to 64 feet in length were equipped with various-sized air-entry jets. Liquid holdup volumes were used to correlate vertical-flow data, and empirical equations for computing gas requirements were derived. The effect of flowstring length on flow efficiency, oil- and gas-production rates, and gas-oil ratios was relatively minor at all flowing pressures. Air-jet sizes and flowstring diameters, however, had a marked effect on flow efficiency and oil- and gas-production rates. The small air-jet sizes increased maximum flow efficiency and its associated flowing pressures but decreased oil- and gas-production rates. An increase in flowstring diameter increased maximum flow efficiency with its associated flowing pressure and also increased the production rates of oil and gas.

Jan 1, 1965

By Joseph A. Cavallaro

This report describes the timed release analysis technique that was developed to serve as a tool for assessing the froth flotation cleaning potentials of fine-size coals. Using this developed technique, 16 coals from 10 different coalbeds were tested. All of the coals included in this study were quite amenable to froth flotation with float coal yields ranging from 80.7 to 99.5 percentage points. Float-and-sink analyses of the coals tested are shown to be of limited value in predicting froth flotation cleaning potential. Generally the float-and-sink analyses indicated a better product could be obtained than froth flotation could provide; although, in four of the coals tested froth flotation results were superior to those expected from the gravimetric analysis. The fixed carbon content of the samples collected was found to correlate with the floatability of the coals. The higher rank coals were the most readily floatable coals while the lower rank coals did not respond quite as well to flotation.

Jan 1, 1965

By C. F. Wingquist

As part of an ongoing study to determine how the wear of mining tools affects dust generation, the Bureau of Mines has measured bit tempera-ture rise during cutting of abrasive rock. Radial bit wear-flat tem-peratures generated by linear cutting in Berea Sandstone were measured as a function of cutting depth and speed. Depths of cut (DOC) were 1/8, 1/4, and 1/2 in, and cutting speeds were 10, 40, and 80 in/s, respectively. Temperature sensing was accomplished by emplacement of a miniature thermocouple into the center of the wear flat. Temperatures observed ranged from 2000 to 5000 C. Correlation between depth and temperature was weak. Temperature increased linearly with speed at 1/2-in DOC, but data taken at 1/8-and 1/4-in DOC produced inconclusive results. The results indicated that at least for deeper cuts (1/2 in), bit temperature, and therefore wear, can be reduced by lowering the cutting speed.

Jan 1, 1987

By H. D. Hess

This report presents the results of laboratory mineral evaluations conducted by the federal Bureau of Mines under the joint sponsorship of the U.S. Atomic Energy Commission (AEC) and the Bureau a! Ships, U. S. Department of the Navy. The major purpose of this investigation was to examine and evaluate zirconium minerals representing sizeable deposits in an effort to locate com¬mercial sources of high-hafnium ores. Although determination of the hafnium content was the principal objective, each of the zirconium minerals also was analyzed for combined zirconium-hafnium oxide, silica, uranium, thorium, yttrium, and cerium. The general laboratory procedure involved microscopic examination of the test samples, concentration of the hafnium-bearing zirconium mineral by standard laboratory techniques, and analysis of the derived concentrate by quantitative microscopic, chemical, and X-ray spectrographic methods. Of the several hundred samples tested under this program, 147 are discussed in this report, including 94 from domestic occurrences and 53 from widespread foreign sources.

Jan 1, 1962

By E. A. Clarke

The vapor-phase section of the Coal Hydrogenation Demonstration Plant at Louisiana, Mo., was operated for the first time in April 1949. The run lasted only 10 days because of time limitation (pending plant dedication in May) and the small amount of charging stock available. The primary purpose of the operation was to break in and determine the operability of the equipment and to supplement the operators' classroom training with actual practice by operating the plant under mild conditions. A secondary aim was to obtain data on the hydrogenation of petroleum oil and lignite tar distillate at approximately 10,000 p.s.i. while making gasoline and Diesel fuel oil. Although the operations were carried out under conditions considerably below those used in the plant design, a great deal of experience and data was obtained. As it is not feasible at this time to conduct further vapor-phase operations on similar stocks, this report has been prepared to present and summarize the data obtained through this operation.

Jan 1, 1950

By H. L. Burmeister

This report describes the mining and milling practices used by the Eastern Magnesia Talc Co. at its Johnson, Vt., operation. The report also contains a description of the local geology and all available information on cost and performance data. Since 1925 the mine has produced continuously at an average annual rate of 54,000 tons, and the ratio of ore hoisted to finished product is roughly 2 to 1. Ore is stoped by a combination of shrinkage and sublevel methods. In any 24-hour period the mill produces an average total of 14 grades of finished talc product, 9 by dry grinding and air classification and 5 by wet grinding and flotation methods. The mine operates one shift per day, 5 days per week and the mill operates on a 3-shift, 5-1/2-day-per-week basis. Operating costs for 1958, on a percentage basis, were mining, 22.34; milling, 54.77; ore haulage, 2.89; and all other, 20.00 percent.

Jan 1, 1963

By Jeffrey Y. Foley

The Bureau of Mines sampled surface exposures of podiform chromite in the Caribou Mountain-Melozitna ultramafic belt in the Kokrines-Hodzana Highlands, central Alaska. Fieldwork began in 1979 as part of an assessment of the mineral potential of lands adjacent to the trans-Alaska pipeline corridor, for the Bureau of Land Management, and continued through 1981 as a Bureau of Mines investigation. The belt comprises six complexes of which the three closest to the pipeline corridor were investigated. Concentrations of chromite disseminated in dunite host rock make up mineralized intervals ranging in thickness from less than an inch to 5 ft and in grade from 3 to 23 pct chromium. The largest occurrence has an exposed strike length of 80 ft. Bulk surface samples were collected from 10 of these exposures, and beneficiation tests on the samples produced concentrates of metallurgical, refractory, and subindustrial grades. Part I--this report--describes the fieldwork; part II--1C 8916--describes the beneficiation work.

Jan 1, 1983

By E. D. Eastman

The basic character of the free energy r data relating to water and the oxides of carbon makes it desirable that the most representative values that can be obtained should be constantly available. The calculations of Lewis and Randall3 retain much of their of original value, but appear to require some modification in the light of more recent work. This paper has been written to incorporate the newer information and to present some estimate of the reliability of the resulting figures. The data upon which the calculations are mainly based are, for these substances, the equilibrium constants of the various reactions involved. The original work relating to these equilibria has, been reviewed and, where possible, weighted to correspond with its probable reliability. The differences in the results of the present from the earlier calculations are partly the consequence of this appraisal and partly of the inclusion of more extensive data, as will be indicated in detail in the succeeding sections.

Jan 1, 1929

By Richard L. Fischer

Constant-volume charges of precipitated PETN (pentaeythrite tetranitrate) at three specific gravities (0.50, 1.00, and 1.50) were used in laboratory tests to examine the effects of changes in explosive properties on free-surface displacement pulses and on crater dimensions. The tests were performed in large blocks of cement-mortar. The values for the detonation velocity, detonation pressure, specific energy, energy density, and energy release rate were calculated from the explosive loading density. Calculated explosive properties were correlated with free-surface displacement pulse measurements, strain energy, and measured crater dimensions. Increases in explosive properties resulted in increased free-surface displacement pulse parameters and crater dimensions. The loading density, detonation velocity, energy density, detonation pressure, and energy release rate were found to be best indicators of explosive performance. Simple acoustic relationships involving impedance ratios were examined and could not be used to predict peak displacement amplitude or strain energy. Data are presented in the customary English units as well as the International System of Units (SI).

Jan 1, 1970

By J. A. Cavallaro

This Bureau of Mines report describes the preparation characteristics of 10 coal samples collected from the significant coal-producing mines of Lucas, Mahaska, Marion, Monroe, and Wapello Counties in Iowa, with special emphasis on physical desulfurization. All 10 samples were of high sulfur content as received, ranging from 4.2 to 10.4 percent; the organic sulfur content ranged from 0.8 to 3.8 percent. The pyritic sulfur content of the samples could be appreciably reduced by crushing and washing and provided pyritic sulfur reductions ranging from 36 to 75 percent. Crushing to 3/8-inch top size and removing the sink 1.60 specific gravity material would provide float coal products containing 3.5 to 6.0 percent sulfur. However, these coals could be burned at utility plants utilizing SO2 removal processes with efficiencies ranging from 70 to 88 percent and still be in compliance with the current Federal SO2 emission regulations for stationary sources.

Jan 1, 1973

By S. J. Gasior

A method for destroying the caking properties of bituminous coal was developed by the Bureau of Mines. Coal is treated in a fixed bed by heating through its plastic range under controlled temperatures in mildly oxidative atmospheres composed of inert gas and/or steam containing about 1 volume-percent oxygen. High-volatile A (hvab) and high-volatile B (hvbb) and low-volatile bituminous (lvb) coals in the size range 1/8 to 1-1/2 inches were successfully treated at 0 (atmospheric pressure) to 300 psig in static beds 6 to 18 inches deep. Conditions of treatment depended on the coal and ranged from 80 to 200 minutes at 350° to 510° C. Char produced in this manner from hvab coal was gasified with steam at 800° C and 100 psig in a fixed bed in one series of tests and in other tests was exposed to hydrogen in a dilute co current free-falling-bed system at 750° C and 3,000 psig without agglomerating.

Jan 1, 1965

By Gary P. Sames

Shale roof deterioration in coal mines. caused by ventilation air humidity fluctuations, is a common ground control problem. Shale roof deterioration often results in increased accidents, decreased production, inadequate ventilation, and increasing operating costs in maintaining haulage roads and airways. The results of Bureau of Mines research indicate that air tempering entries are an effective method of controlling deterioration prone shales. Some of the conclusions and recommendations drawn from Bureau research include (1) moisture sensitive shales will react adversely to moisture gains and losses, (2) the majority effect of specific humidity fluctuations can be concentrated in and absorbed by tempering entries, (3) tempering entry panels should be located as near to the main intake as possible, (4) tempering panels should be designed for a conservative recovery and provide a minimum of 20-to 30-min air residence time, (5) ventilation and escapeway requirements must be considered early in panel design, and (6) an efficient support and sealant plan can increase the life expectancy of a tempering panel.

Jan 1, 1985

By J. G. Donaldson

Binary alloys of molybdenum and tungsten were prepared by the Bureau of Mines in laboratory-scale experiments by hydrogen reduction of their vaporized hexafluorides. Near-optimum deposition parameters were determined, and the nature of the deposited alloys was investigated. Dense, homogeneous alloys were codeposited between 650° and 750° C with a reduction efficiency of more than 75 percent. The alloy composition was uniform when the hydrogen ratio in the gas feed mixture did not exceed 3 times the stoichiometric requirement. Regulating the proportions of the metal hexafluorides in the gas feed provided a large degree of control over the composition of the deposit. Hardness of the deposits varied directly with the proportion of excess hydro,,,, in the gas feed and with the weight-percent of tungsten in the alloy. Hardness was not affected by deposition temperature over the range 650° to 750° C for specimens of similar composition. Extreme brittleness and unsuitable physical shapes of the alloys prevented tensile strength measurements.

Jan 1, 1966