Search Documents

By Paul Sands

Single- and two-stage tests were made with 6-inch, coal-cleaning hydrocyclones to determine the effect of hydrocyclone geometry, operating conditions, and feed composition on performance. Most of the testing was conducted in an open-circuit pilot plant that had a maximum capacity of about 9 tons per hour. The coals used in the investigation had top sizes of 1/4 inch and 28 mesh. Considerable latitude was found in the range of geometry variables that could be used without affecting performance adversely, although a certain minimum ratio of overflow to underflow openings had to be maintained for best operation. Two-stage cleaning proved distinctly better than operation with a single hydrocyclone, because clean coal lost in the refuse product of the primary unit can be partly recovered in the secondary. There is an unusually great difference in the specific gravities at which the individual sizes of the feed are separated in the hydrocyclone. This militates against high efficiency because maximum yield occurs when all sizes are cleaned at the same specific gravity. The size composition of the feed and, more particularly, the size composition of the impurity have a greater influence on the efficiency attainable in the hydrocyclone than in most other types of fine-coal cleaners.

Jan 1, 1968

By David C. Oyler, Paul B. Stubbs

The Bureau of Mines and United States Steel Corp. are conducting a joint project to monitor formation pressures at a large (23-well) coal- bed gas drainage field near Oak Grove, AL. Three monitor holes were drilled in late 1981, and pressure monitoring began in December 1981. The Bureau of Mines direct method was used to obtain gas content data from cores taken in the monitor holes. Comparison of the 1981 gas con- tent data from the monitor holes with initial gas content values obtain- ed from the production wells in 1977 indicates a 50-pct reduction in ad- sorbed gas content inside the pattern and a 29-pct reduction at one point 500 ft outside the pattern. The combination of pressure and gas content data has also allowed an in situ isotherm curve, relating the formation pressure to adsorbed gas content, to be developed for the area of the production wells. From the current rate of pressure decline (1 lbf/inz per month), the observed changes in gas content, and the isotherm curve, it appears that most of the early gas production came from within the pattern, but since 1981 (and possibly earlier) most of the gas produced has been migrating to the wells from outside the pattern area.

Jan 1, 1985

By T. F. Anstett

The Bureau of Mines investigated the availability of platinum from known major deposits in market economy countries. Fifteen of these deposits contain demonstrated resources totaling 302 million troy ounces of platinum. Detailed geologic, engineering, and cost evaluations were performed on each deposit to determine its potential for platinum production. There are large amounts of demonstrated platinum potentially available from market economy deposits that were not analyzed owing to lack of adequate data or to technological limitations. These include 297 million troy ounces contained in the UG2 and Platreef of the Bushveld Complex, South Africa. This analysis indicates that about 11 0 million troy ounces (2.3 million ounces annually) of platinum are potentially available at the January 1980 producer price of $420 per troy ounce, nearly all from South Africa. An additional 85 million troy ounces occurring in Zimbabwean deposits would become available only through more than a quadrupling of that price. In order to meet projected world demand of 3.5 million troy ounces in 1990, platinum price may have to increase. Only one domestic deposit, the Salmon River in Alaska, is capable of producing platinum at $420 per troy ounce. Regardless of price, at assumed production capacities, domestic deposits could supply less than 10 percent of annual U.S. requirements.

Jan 1, 1982

By J. M. Gomes

The Bureau of Mines investigated electrolytic techniques for preparing diborides of the group IV B metals. TiB2, ZrB2, and HfB2 were electro-deposited from their respective oxides dissolved in borate-chloride-cryolite electrolytes. Titanium diboride was also electrodeposited from rutile (Ti02) dissolved in a Na2,B4O7-Na2C03-Na3A1F6-NaC1 electrolyte at 1,050° C; 14 kW-hr were required to produce 1 pound of TiB2. Major impurities in the TiB2 produced in a 10-deposition cycle experiment, in weight-percent, were Al, 0.2; Cr, 0.3; Fe, 0.1; V, 0.3; C, 1.4; and 0, 1.0. Zirconium diboride was electro-deposited from zircon (ZrSiO4) dissolved in a Na2B407-NaOH-Na3A1F6-NaCl-NaF electrolyte at 1,050° C. The ZrB2 produced in a 10-deposition cycle experiment contained the following impurities in weight-percent; Fe, 0.1; Si, 0.5; C, 0.3; and 0, 0.6. Energy required to produce 1 pound of ZrB2 was 9.3 kW-hr.

Jan 1, 1975

By J. M. Kuchta

The chemical and thermal criteria used for predicting the spontaneous combustion hazard are briefly reviewed and data are presented to characterize the gas desorptions and self-heating tendencies of 29 U.S. coals. Closed vessel desorption experiments showed that CO, CO2, and CH4 are the main gases evolved and that the CO, CO/?O2 index, and 02 absorption rate increase with decreasing rank and increasing oxygen content of the coal. In this Bureau of Mines report, the effects of temperature, moisture, and other variables are discussed together with the application of the data to the complex conditions encountered in a mining environment. An important finding is that the presence of CO alone in a mine is not necessarily an indication of a self-heating reaction of the coal. Based upon experiments conducted in an adiabatic-type calorimeter, the self-heating temperatures of lignite and subbituminous coals can be as low as 30° C, whereas the bituminous coals require a temperature of about 60° C or more. The self-heating hazard is greatest when the coals are dried and exposed to a high humidity condition, apparently as a result of the "heat-of-wetting." Generally, the hazard is greatest with the western coals of the United States.

Jan 1, 1980

By J. J. Forbes

The investigation of major and minor coal-mine disasters has been a routine function of the Bureau of Mines since its inception in 1910, and the facts obtained during such investigations have been used as a basis for determining the precautions that the personnel of many mines are observing to prevent similar occurrences, The Bureau has conducted extensive research on roof-control problems, but a comprehensive study of fatal roof-fall accidents was not attempted until February 10, 1950, when the policy of investigating all coal-mine fatalities was approved by Bureau of Mines Director James Boyd. The investigations are being conducted by Federal coal-mine inspectors functioning under the provisions of the Coal Mine Inspection and Investigation Act of May 1941, Public Law 49, and reports covering the investigations are distributed to management, the State mine inspection agency, and representatives of the mine workers organization having jurisdiction at the mine. SCOPE AND PURPOSE OF STUDY This study covers the Federal investigation of 263 of the 315 fatalities from falls of roof, face, or rib that were charged to the bituminous-coal industry during the calender year 1950. The number of roof-fall fatalities investigated is recorded by States in table 1.

Jan 1, 1951

By S. D. Maksimovic

The Bureau of Mines identified and evaluated major sources of quartz dust during overburden drilling at a surface coal mine, The relative contribution of each source to the total dust hazard was estimated, using personal gravimetric and instantaneous dust-sampling devices. No attempt was made to determine actual dust generation rates. The major sources of dust at the drill rig during dry drilling opera-tions were the collector dump, drill shroud leakage, and drill stem seal leakage, These sources contributed 90 pct of the respirable dust and 89 pet of the respirable quartz dust generated during drilling, The collector dump cycle (21.6 pct of total drilling time) accounted for 38 pct of the respirable dust and 41 pct of the respirable quartz dust, with peak dust concentrations reaching 68 mg/m3. Shroud and drill stem leakage contributed 28 and 24 pct of the respirable dust and 32 and 16 pct of the respirable quartz dust, respectively. A dragline and second drill rig contributed the remaining 10 pct of dust and 11 pct of quartz dust. Gravimetric dust samples collected inside the drill cab and outside, near the cab door, averaged 1.65 and 1.43 mg/m3, respectively, with 6 pct respirable quartz.

Jan 1, 1985

By Harvard Eng

An industrial survey was made for the Missouri Basin Field Committee of the Department of the Interior to determine the type and quantity of water-borne mineral wastes and the water requirements of metal-processing industries in the basin in Kansas and western Missouri. Data are presented on metal-processing plants visited through June 30, 1959. Most of the plants were in the greater Kansas City area. This report is to be supplemented with a similar publication on other industries, including those producing sand and gravel, coal, petroleum, and chemicals. In 1958, 19 million pounds of waste materials was discharged from metal processing industries. Approximately 14 million pounds of this waste was in the form of ferrous sulfate, and 2 million pounds was ferric phosphate. Galvanizing, other hot dipping, and automotive industries contributed the greater part of iron compounds wasted; some of this waste occurred as sludge that was not discharged to water courses but was hauled to refuse dumps, podium was present in nearly all industrial wastes, and the total of more than 900,000 pounds constituted one of the larger material losses. Although small in quantity, electroplating and allied coating wastes contained metals that were expensive when originally purchased.

Jan 1, 1961

By J. T. Popp, C. M. McCulloch

This Bureau of Mines study reviews the geological factors that affect methane in the Beckley coalbed in southern West Virginia, including overburden, coalbed structure, type of and changes in lithology above and below the Beckley coalbed, and presence of fractures in the coal and rock adjacent to the Beckley. Depending on the depth, the Beckley coalbed emits from 216 to 520 ft3 of methane per ton of coal mined, and the Bureau estimates that methane emission in a deep, extensively developed mine in this area may exceed 3,000 ft3 per day per ton of coal mined. Average face cleat and butt cleat trends in the Beckley coalbed measured underground are N 33° W and N 53° E, respectively. Close cleat spacing con- tributes to the friable nature of the Beckley and provides easy movement for methane and water. Because rider coals, splits, and carbonaceous shales may contribute methane to mine emissions, predictions of methane emission based on gas content of the Beckley coalbed alone may be conservative. Beckley coalbed reserves in the study area are 234 million tons. The gas content of the Beckley coalbed averages 407 ft3/ton, and the coalbed gas reserves are 108 billion ft3.

Jan 1, 1976

By M. M. Fine

In an experimental study by the Bureau of Mines, in cooperation with National Lead Co., the roast-flotation process was found to be an effective means of upgrading certain cobalt-nickel stockpiles. The research was undertaken to determine whether the process could yield an enriched feed, with a minimum cobalt content of 6.0 percent, for the company refinery. The stockpiles (products of the company Fredericktown, Mo., milling operations) were essentially complex sulfides of cobalt, nickel, copper, lead, and iron, 1 sample of which contained 2.84 percent Co and 3.57 percent Ni. After a controlled oxidizing roast at 400° C., laboratory flotation with conventional sulfhydric reagents yielded an enriched concentrate analyzing 9.22 percent Co and 11.43 percent Ni, with recoveries of 84.9 and 85.8 percent, respectively. These are typical laboratory data; other data indicated higher grades were possible but at reduced recoveries. A brief, continuous campaign verified the applicability of the process to the raw material in question but was not continued long enough to establish optimum conditions. As a consequence, the results of the large-scale tests did not equal those obtained in the laboratory but definitely confirm the beneficiation possible from the roast-flotation process.

Jan 1, 1958

By Michael T. Nigbor

The Bureau of Mines assisted the Rocky Mountain Energy Co. in a pilot-scale in situ leaching experiment at Casper, Wyo., to determine if sulfuric acid can be used as a cost-effective alternative lixiviant (leachant) for uranium in situ leaching. This experiment, which lasted more than 2 years, is the first fully documented pilot-scale operation in which the leaching-restoration cycle was completed using sulfuric acid instead of the more common carbonate-bicarbonate leachant This report describes activities at the experimental site, presents extensive geochemical data from startup to site restoration, compares laboratory and field experiments, and discusses the environmental aspects of acid leaching. The data showed that sulfuric acid is apparently an effective leaching solution. Three to five grams of acid per liter of ground water resulted in a production solution grade of 80 to 100 ppm uranium. Restoration was successful, but required extended flushing. The pH was the last chemical parameterto return to baseline, requiring about 350 days. This was longer than was predicted in laboratory simulations. The data also showed that mobilization of toxic elements such as selenium, arsenic, radium, thorium, and molybdenum stayed within reasonable limits and quickly fell back to preleach concentrations during restoration.

Jan 1, 1982

By Richard D. Miller

The helium resources base of the United States was estimated by the Bureau of Mines to be 961 Bcf as of January 1, 1983. These resources are divided into four categories in decreasing degree of assurance of their existence: (1) helium in storage and in proved natural gas re- serves, 271 Bcf, (2) helium in probable natural gas resources, estimated at 202 Bcf, (3) helium in possible natural gas resources, estimated to be 351 Bcf, and (4) helium in speculative natural gas resources, which makes up the remaining 137 Bcf. These helium resources are further divided into depleting, nondepleting, and stored classifications. The depleting resources are those associated with natural gas fields that are, or will be, produced for the natural gas they contain. All of the helium in potential (probable, possible, and speculative) natural gas resources is included in this classification. These depleting resources are estimated to contain 789 Bcf of the total helium resource base. Helium resources contained in nondepleting natural gas resources, those in shut-in, abandoned, or otherwise nonproducing natural gas fields, are estimated to total 134 Bcf. There is 38 Bcf of helium in storage in the Federal Government- owned Cliffside Gas Field near Amarillo, TX.

Jan 1, 1985

By V. R. Spironello

One of the primary objectives of the Bureau of Mines solid waste utilization program is the recycling of the magnetic fraction of municipal solid waste called raw refuse scrap. In this investigation, several types of scrap of differing quality, including refuse and turnings, were melted in a 1-ton electric-arc furnace in various combinations to produce steel in noncritical (construction) grades. In-formation on furnace operation and on the behavior of tramp and alloying elements was obtained. The research showed that it is possible to produce acceptable steel from a variety of steel scrap. Although some scrap is routinely used in steelmaking, it was found that up to 50 to 55 pct of the scrap charge can be ref-use, provided it is combined with higher quality scrap. The chemistry of the steels was generally acceptable, and all of them were rolled without difficulty. The specification (ASTM 615) for the steels produced was grade 40 or grade 60, containing 0.30 or 0.40 pct C, with mini-mum yield strengths of 40,000 or 60,000-psi, respectively. Most of the steels met the specification requirements. In-formation on typical microstructures of some of the steels is included. The composition of some furnace dusts showed high levels of Sn, Pb, and Zn.

Jan 1, 1981

By J. M. Singer

The objective of this investigation was to determine minimum air velocities and entrainment rates for coal and rock dust dispersion in wind tunnel experiments under conditions that simulate dispersion from surfaces in coal mines where airflows are induced by weak gas explosions. Dust deposits were bed-or ridge-shaped; particle sizes were 6 to 80 microns (cohesive deposits) or 100 to 150 microns (free-flowing deposits); and wind tunnels were 7.62 cm wide by 5.08 cm high by 300 cm long, and 2.4 m wide by 1.5 m high by 215 m long. The investigation showed that minimum air velocities (directed at mid-height) of separate, layered, or mixed piles of coal dust and rock dust were within the range 5 to 30 m/sec, independent of size of wind tunnel. This finding considerably facilitates scaling of data to mine-size passageways. Free-flowing deposits dispersed relatively slowly by single-particle detachment; cohesive dusts dispersed faster by the breaking and lifting of large clumps along weak failure flames; particle dispersion occurred in flight. Layered or mixed deposits of coal and rock dust did not disperse selectively. Semiempirical expressions were derived relating minimum air velocities and dispersion rates to dust-pile geometry, cohesion, porosity, and bulk density.

Jan 1, 1972

By S. Ralph Austin

This Bureau of Mines investigation determined the effects of so-called annealing at high temperatures on radon-222 emanation from domestic uranium ores. Concurrently, a method was developed for closely estimating the emanation coefficients of hot samples from measurements of their gamma activity after cooling. Emanation coefficients of 102 samples from 14 domestic areas of past, present, and possible future uranium production were investigated using modifications of the closed-can, gamma-only assay method at and after cooling from 100° to 1,000° C. True annealing probably does not occur below 500° C. In limited investigations at 500° C and above, effects of annealing are masked by the effects of other parameters. Emanation is commonly less at one or more of the steps investigated in the 100° to 500° C range than before heating. This decrease is tentatively attributed to water loss at temperatures dependent upon the minerals present. The average sample emanates least at 300° C; emanation increases with higher temperatures to at least 900° C. Emanation decreases sharply on cooling, but it is partially restored by prolonged exposure to the atmosphere at room temperature. Higher than average emanation of coffinite ores at 500° C and above may be related to destruction of the coffinite crystal structure.

Jan 1, 1979

By Charles L. Kimbell

World political events that occurred subsequent to yearend 1989 but that bear heavily on the global mineral industry have been of such significance that they cannot be disregarded, and certainly they contribute to any type of "outlook?. However, to write of them simply as "forecasts" in an "outlook" section of this study would be to unjustly pretend to status as prophets. Thus, this section covers events that have occurred not as predictions but rather as history. The section also includes an element with some broad statistical information, but this is included last rather than first for two reasons: the information is subject to considerable re- vision as additional data become available and as preliminary returns are corrected; and the authors view it as less important than the events that govern the statistics. The Near East and the Crisis There.- Of all 1990 political events influencing the world's mineral industry, the Iraqi invasion of Kuwait and the remarkable events that followed this aggression must head the list. The almost immediate imposition of economic sanctions, involving embargoes on shipment of virtually all goods into and out of Iraq, caused severe dislocations in the production and trade of mineral commodities, not only within the region itself, but with a ripple effect, into other world areas as well.

Jan 1, 1992

By Jack L. Henry

A laboratory and a pilot-plant-scale investigation has been conducted by the Bureau of Mines to examine possible sources of nitride defects in the production of magnesium-reduced titanium sponge. The production of alpha-stabilized nitride inclusions in hot-rolled titanium plate from air contamination of sponge during its manufacture has been experimentally demonstrated. Magnesium-reduced sponge prepared from air-contaminated magnesium or when contaminated by an air leak during reduction, vacuum distillation, or inert gas sweep, shows very large variations in nitrogen content. Refractory nitrides, delta TiN and epsilon Ti2N have been identified in this sponge. The highest incidence of inclusions resulted from sponge that was reduced by air-contaminated magnesium and from sponge subjected to air contamination during the vacuum distillation cycle and during helium sweep. Air contamination of sponge during the reduction cycle was not nearly as effective in producing inclusions. Tests showed that color and texture may not be reliable criteria for locating defects during sponge inspection. Maintenance of good vacuum-tight integrity, filtration of molten magnesium prior to charging into the reduction retort, and mechanical attrition of sponge to pulverize and disperse nitrides are suggested as practices to lower inclusion incidence in commercial titanium ingots.

Jan 1, 1974

By T. J. Batchler, T. M. Barczak

The Code of Federal Regulations (CFR) requires that the transverse load capacity of stoppings be equal to or greater than traditionally accepted in mine controls, which for block stoppings is generally accepted as 39 psf as referenced in the preamble to the CFR standard. This measure is based on physical testing of a freestanding wall in accordance with ASTM E 72 specifications, where our past research has shown that the dominant parameter is the tensile strength of the sealant. A new protocol based on rigid arch loading of the structure is proposed to determine the true transverse load capacity of block stoppings. Arching is achieved by the restraint of the stopping against the mine roof and floor, whereby compressive forces are developed within the wall. A laboratory procedure using the NIOSH Mine Roof Simulator (MRS) to simulate rigid arching of block stoppings was developed and results verified through full-scale in-mine tests. The rigid arch tests have demonstrated transverse load capacities more than an order of magnitude higher than the ASTM E 72 evaluation method from which the 39-psf requirement is derived. More importantly, the rigid arch tests have shown that the load capability is dependent on the physical properties of the block and geometric properties of the wall and not the sealant.

A general description of investigative work conducted by the Bureau of Mines at the, Missouri Valley. manganese deposits and leading to tonnage and grade estimates has been given in Report of Investigations 4375, part 1 of a three-part report of work done between July 1945 and August 1947. Basic factual information from which tonnage and grade estimates were drawn was derived through the drilling sampling of 238 large-diameter bucket-drill holes in 11 widely separated areas. Drilling areas were selected after careful reconnaissance, mapping, and consideration of earlier work done on the deposits by the Bureau of Mines, State agencies, and private organizations and individuals. Stratigraphic studies permitted extending the results compiled within the drilling; areas to outcrop and lightly covered manganiferous zones between an beyond drilling areas. The locations of drilling areas, drilling sections, and individual drill hues are shown on illustrations in part 1 f this report. The individual drill holes, aside from providing the basic information for tonnage and grade estimates, disclosed features affecting any future plan As exploitation. It in particularly significant that a large part of the visible outcrops is faulted end otherwise complicated by slides that give a false impression of the thickness, vertical location, and even the existence of manganese-bearing zones.

Jan 1, 1949

Tennessee is the largest federal program state in the nation, with 62 active surface and underground coal mines. Tennessee's coal resources lie in 22 coal seams in 22 counties. Twelve seams are being mined at this time. Mining in the northern counties is primarily in steep slope areas in the Cumberland Mountains. The relatively flat terrain associated with the Cumberland Plateau makes area-rnining the most common production method in Tennessee's southern counties. The State of Tennessee gained primacy August 10,1982, when its regulatory program was conditionally approved, subject to the correction of certain deficiencies. On May 16,1984, the Tennessee General Assembly repealed most of the Tennessee Coal Surface Mining Law of 1980, effective October 1, 1984. With this action, withdrawal of the state regulatory program was formalized, and on October 1,1984, the Office of Surface Mining's Knoxville Field Office became the regulatory authority. Tennessee is not eligible to receive funds for an abandoned mine reclamation program because it does not have an approved regulatory program. Accordingly, the Tennessee Abandoned Mine Lands Program does not receive federal AML grants. Since 1984, AML projects have been completed under cooperative agreements between OSM and the state; emergency projects are completed by the Office of Surface Mining.

Jan 1, 1992