Search Documents

By C. Froger

Since its creation in 1950, the Centre d'Etudes et Recherches des Charbonnages de France at Verneuil-en-Halatte (Oise) has been conducting many investigations concerned with airborne dust measurements, particularly in underground mines. The work has resulted in the development, a few years ago, of a new process of dust sampling, whereby the airborne dust particles are collected by a rotary filter of polyurethane foam rotating at high speed within 8 housing.

Jan 1, 1973

By E. R. Maize

This report is the third of a series on convergence of roof and floor in coal mines and subsidence of surface that accompanies it. The first paper5/ dealt with extraction in a mechanized mine (Montour 10) having relatively short rib lines that retreat rapidly. The second dealt with extraction in a mine (Crucible) in which coal was loaded. by hand and in which the rib lines wore long and slow-moving. The present report deals with a mine (Gibson) in which conditions approximated those in the Crucible mine, except that the distance between room centers was considerably less and the pillars were narrower in consequence. Moreover, the average cover was less and the studies were made under the steep hillside of a stream valley compared with a gently rolling surface over the portions of the second mine studied. Gibson mine lies in the east-central hart of Washington County, Pa. , approximately midway between the Montour 10 end Crucible mines on a north-south line. A cooperative agreement covering the work was made with the Hillman Coal & Coke Co. through W. L. Affelder, vice president. This paper describes the methods used in the investigation, gives excerpts from the data obtained, and offers such generalizations as appear to be justified.

Jan 1, 1940

By Alton Gabriel

During the fall of 1940, J. R. Thoenen of the Mining Division, Bureau of Mines, accompanied by the senior author, surveyed the more important domestic alunite deposits. Although the study was designed primarily as an economic survey, samples from a number of the deposits were collected to investigate the beneficiation of the lower-grade material.

Jan 1, 1942

By J. P. Morris

The Bureau of Mines investigated the mechanics of fuming of iron-carbon melts during top-blowing with oxygen. Melts weighing 45 lb were prepared in an induction furnace and blown with oxygen by means of water-cooled lances. The rate of fuming was measured and correlated with the operating variables. The data showed that the primary cause of fuming was a boil at the bath surface in the impingement zone of the oxygen jet. Nucleation of the carbon monoxide bubbles producing the boil was apparently brought about by the precipitation of an oxide phase. The actual fuming mechanism involved partial oxidation and vaporization of bubble films and fine metal spray generated by the bursting of the bubbles. Bubbles that formed outside the impingement zone produced little fume. The distribution of trace elements between the metal and fume strongly indicated that the fume contained fine spray particles as well as particles that had condensed from vapor. The rate of fuming was found to be proportional to the carbon content of the metal) the concentration of oxygen in the jet) and the bath temperature) provided that a continuous boil occurred. In the absence of a boil) very little fume was produced.

Jan 1, 1967

By R. P. Maloney

Since mining operations began in 1900, Government geologists and mining men have periodically recorded the presence of the minerals of mercury and antimony in the extensive gold placer deposits near Flat in the Iditarod district of the Yukon River region, Alaska. No serious effort was made to recover the cinnabar contained in the gold placer gravels, and there is no evidence that veins of cinnabar and stibnite exposed in the placer operations (as reported by the Geological Survey) were ever explored or developed. A large monzonitic intrusive, which is the dominant geologic feature of the immediate area, is believed to be the lode source of the valuable minerals in the placer deposits. In contact with the monzonite are argillite and quartzite, metamorphic products from the Cretaceous shales and sandstones.

Jan 1, 1962

By James M. Spear

The U.S. Bureau of Mines conducted a mineral survey of the Domeland Addition (5207) and Woodpecker (5206) RARE II areas during the summer of 1979. These study areas were examined to determine the presence or absence of mineral resources and reserves and where possible, to estimate values. The study areas are 9 air mi northeast of Kernville, California, and encompass 47,400 acres of primarily granitic rocks of the Sierra Nevada batholith with some scattered exposures of older metasedimentary, volcanic, and metavolcanic rocks. These other rock units partially surround the exposed batholith in the Domeland Wilderness and consist mostly of late Paleozoic quartzites, mica schists, marbles, and meta-volcanics, Mesozoic quartz diorite and gabbro intrusives, and local Tertiary basalt and andesite flows.

Jan 1, 1981

By Alton Gabriel

During the fall of 1940, J. R. Thoenen of the Mining Division, Bureau of Mines, accompanied by the senior author, surveyed the more important domestic alunite deposits. Although the study was designed primarily as an economic survey, samples from a number of the deposits were collected to investigate the beneficiation of the lower-grade material.

Jan 1, 1942

By E. R. Maize

This report is the third of a series on convergence of roof and floor in coal mines and subsidence of surface that accompanies it. The first papery dealt with extraction in a mechanized mine (Montour 10) having relatively short rib lines that retreat rapidly. The second 6/ dealt with extraction in a mine (Crucible) in which coal was loaded by hand and in which the rib lines were long and slow-moving. The present report deals with a mine (Gibson) in which conditions approximated those in the Crucible mine, except that the distance between room centers was considerably less and the pillars were narrower in consequence. Moreover, the average cover was less and the studies were made under the steep hillside of a stream valley compared with a gently rolling surface over the portions of the second mine studied. Gibson mine lies in the east-central part of Washington County, Pa., approximately midway between the Montour 10 and Crucible mines on a north-south line. A cooperative agreement covering the work was made with the Hillman Coal & Coke Co. through W. L. Affelder, vice president. This paper describes the methods used in the investigation, gives excerpts from the data obtained, and offers such generalisations as appear to be justified.

Jan 1, 1940

By Charles H. Simmons

Two versions of a VF transceiver to aid in location of trapped miners has been developed and tested. The belt worn model was produced in both transmitter and transceiver configurations. In addition, a quantity of the belt worn models were fabricated using aluminum wire instead of copper in order to reduce unit weight. Ten prototypes of a battery cap model VF transceiver were also fabricated demonstrating further unit size and weight reduction while maintaining electrical performance. Samples of- both versions were tested environmentally and the test data is included in this report. While both versions of the VF transceiver are similar electrically, and are constructed using convential manufacturing techniques, the battery cap model realizes a lower total weight, smaller volume and production cost than the belt worn version. Operationally, the battery cap model assures that the VF transceiver will always be with the miner.

Jan 1, 1981

Horizontal holes are drilled underground into coalbeds to control methane flow from ribs and active face areas and to make gas pressure measurements in coalbeds. Gas pressure measurements are made by drilling the same hole incrementally. After each increment, the hole is filled with some type of packers and allowed to reach equilibrium before a gas pressure reading is taken. As the length of hole increases, more packers are required to effect a seal and obtain a reliable pressure measurement. Problems have been encountered in obtaining satisfactory packer seals due to the friable nature of the coalbed. New methods of packing the holes must be used. Therefore, this project was established to evaluate materials and develop a new technique in which a semiliquid and/ or rigid type grout could be placed in the hole to provide satisfactory sealing.

Jan 1, 1972

By J. Ronald Lawter

The purpose of the work described in this report was to measure the effects of diesel engine emissions on the air quality of work areas in a coal mine. Concentration measurements of a number of diesel related air contaminants were made at the Martin County Coal Corporation Mine in Inez, Kentucky. Compounds measured included carbon dioxide, carbon monoxide, formaldehyde, nitric oxide, and nitrogen dioxide. In addition, concentrations of the two classes of odorous compound;, aromatic hydrocarbons, and oxygenates were obtained along, with aldehyde concentrations. Surveys were made of the mine by odor analysts to determine the perceived intensity of diesel-produced odors. It was found that the concentrations of the measured species were well below their Threshold Limit Values. Odor intensity levels in the moderate to strong range were observed in the mine.

Jan 1, 1977

By James Gibbs

In order to provide an initial approach to the deposits of oil shale, nahcolite, and dawsonite in the central area or the Piceance Creek Basin in northwestern Colorado, the U.S.B.M. and associated contractor personnel drilled and cased a 96-inch ID shaft to a depth of 2,371 feet. The shaft was constructed using ?big hole? drilling techniques and succeeded in giving access to previously inaccessible deposits of the above minerals. This report documents the construction from its beginning in January 1977 to its completion in January 1978. Procedures used and problems encountered are discussed in detail.

Jan 1, 1978

By Mandius C. Lundal

This report describes the work done to develop a coal mining machine to increase productivity and recovery from thin seams beyond the highwall, in addition to decreasing the miner's susceptibility to to highwall hazards. First, radar transducers were adapted to measure coal thinkness and detect rock and coal interfaces; Then, the radar was incorporated into a cutterhead with steering controls. Next, visual displays were designed to show cutter position in the coal seam, and anticipated change In coal seam inclination. Finally, development of a telemetry system made remote control of the cutterhead possible. Simultaneously, a high-performance extended depth (HPxD) auger machine was designed with an automatic system to handle 600 ft of 36-in. diameter dual spiral flight conveyor sections. A two man crew controls all operations from a weather conditioned cab outside the VDZ, either at night or day time. As a primary mining tool, working 4000 hr/yr (2 shifts/day) recovering 60% of the coal 600 ft beyond the highwall, production to 500,000 ton/yr can be achieved. Volume II contains technical discussion of subsystems and machine drawings.

Jan 1, 1977

By A. E. Ketler

A second generation lighting system was installed in the Greenwich Collieries longwall. This report describes the hardware, installation, maintenance, and final results of the program.

Jan 1, 1978

By Paul H. Lu

This Bureau of Mines report summarizes the analysis and eveluation of the field measurement results of a comprehensive ground control study conducted in a mechanized longwall coal mine in West Virginia. Emphasis is placed on the three basic ground control parameters: ground pressure, ground movement, and geomechanical properties. Specific topics include premining ground pressures, front-abutment pressure in the longwall panel, histories of pillar loading, differential roof-strata movement and bed separation, differential floor strata movement, entry roof-to-floor convergence, in situ moduli of rigidity of coal seam and roof and floor strata, and mechanical properties of coal and coal measures rocks.

Jan 1, 1985

By R. K. Linn

The New Idria Mining and Chemical Co. owns and operates the New Idria mine in southern San Benito County, Calif. During 1957-59, the New Idria mine was the largest producer of mercury in the United States and its alltime production of over a half-million flasks was exceeded only by one mine. It is one of the oldest and most consistent producers in California. With the exception of 1921-22, the mine has an annual production of mercury dating back to 1854. This paper by the Federal Bureau of Mines describes the exploration, development, mining, and furnacing of mercury ore at the New Idria mine. Figure 1 is a view of the furnace plant of the New Idria mine. The purpose of this report is to promote the development and conservation of our mineral resources by dissemination of technological information on mining and processing procedures, and related practices at operating mines.

Jan 1, 1961

By G. N. Schrauzer

Work has been carried out in the development and testing of carbon monoxide (CO) detection devices which use silica-gel impregnated with metal salts. If carbon monoxide is present, the ?detection gel? (the treated silica-gel) changes from a yellow to a blue-green or blue color. The detection gel "regenerates", i.e., returns to its original yellow color, within 4-24 hours after removal from air containing CO. The detection gel exhibits a threshold of CO response which can be adjusted over a wide range of CO concentrations, typically from 50-500 ppm in air. The preparation of detection gel using salts of palladium, molybdenum and copper is described. Also reported are the results of testing the detection gel&apos;s response to carbon monoxide under varying conditions of temperature and humidity and in the presence of some potentially interfering gases. Low levels of hydrogen sulfide (~ 5 ppm)1 nitrogen dioxide (< 7 ppm), and acetylene (> 200 ppm) were found to affect the detection gel. Temperature and humidity were also found to affect the detection gel&apos;s response. Increasing temperature shortens the gel?s response time while increasing the humidity delays the gel?s response and alters the threshold of the gel. A brief discussion of the further research and development necessary to stabilize the detection gel?s desirable characteristics is included. Descriptions of testing equipment and procedures are covered in detail.

Jan 1, 1978

By Thomas E. Doerfler

Information and data related to the occurrence of fatalities due to major disasters in metal/nonmetal underground mines were analyzed. Standard statistical methods were used to estimate the probability of occurrence of major disasters, and to examine the relationship of disasters to injury statistics published annually.

Jan 1, 1980

By W. L. Hunter

The research on this report was conducted to obtain information on the feasibility of producing ferro chromium of varying silicon and carbon contents from domestic chromite. Concentrates from the Mouat deposit were chosen because they typify the chromite found in the Stillwater complex, the largest domestic reserve, and are similar in composition to other extensive North American and foreign deposits. Batch-smelting tests designed to produce high-, medium-, and low-carbon ferrochromium were made in single phase and three-phase, electric-arc, steelmaking furnaces. Agglomeration studies were made in a rotary kiln. Continuous smelting tests were made to yield data on the production of high-carbon ferro chromium and low-carbon ferrochromium-silicon. The carbon content of high-carbon ferrochromium was lowered to the medium-carbon range by oxygen injection. Mouat stockpile concentrates were nodulized in a gas-fired rotary kiln using quartz, limestone, and fluorspar additions in the proportion necessary to flux the slag. The nodules were smelted in a continuous test using coal, coal char, and mixtures of the two consecutively as reductants.

Jan 1, 1961

By S. S. Gross

A program was conducted to determine whether sufficient quantities of the flame retardant, ammonium phosphate, could be incorporated in a water-based foam solution to prevent or delay reignition (burnback) without. significant degradation of foam properties. Up to 20% of mono and diammonium phosphate was added .to d high expansion foam solution. This mixture was applied as a high expansion foam to burning wood and coal samples. The effect of this mixture on burnback was laboratory tested by placing the wood or coal sample in front of a radiant panel. It was found that diammonium phosphate levels of 20% by weight prevented reignition without degrading foam properties. A field test was then conducted using a 20%, diammonium phosphate mixture and a control with no phosphate on a wood crib fire. The experimental foam did extinguish the crib fire faster than the control as evidenced by the smoke from the crib. However neither crib reignited.

Jan 1, 1982