Search Documents

By Albert L. Toenges

The introduction of mechanized mining in coal mines, which has speeded loading, has emphasized the importance of efficient underground transportation systems. The purpose of this investigation is to study and analyze various systems now in use, and to derive conclusions therefrom. This report may be helpful to operators who are planning new systems of transportation or who are revising present systems to increase their efficiency. This paper is the first of a series on this subject and describes some systems of transportation utilizing rail haulage. ACKNOWLEDGMENT The information used in preparing this report was obtained through the courtesy and cooperation of the officials of the companies whose mines were studied. The descriptions of the transportation systems at the mines included herein have been checked for accuracy, and publication of the data has been approved by the executives of the several operating companies.

Jan 1, 1940

By J. D. Dixon

This Bureau of Mines report describes the results of an investigation for developing and applying procedures for stabilizing excavations openings in highly yielding ground. The approach developed in this report involves nonlinear modeling of the progressive relaxation of the zones of rock mass around the excavations opening where Coulomb criterion of failure is exceeded. Stresses are calculated by using a computer code; Coulomb-failure condition is examined for both intact rock and joints (using strength parameters [~] and c). The rock mass in the failed zones is relaxed by reducing the Young's modulus of the rock based on an empirical formulation that is a function of the shape of the opening and the extent of the failed zone. In addition, the material in the failed zone is assigned reduced strength paramters 0' and c'. The limiting (or convergent) relaxed zone is obtained through an iterative process by manually changing the rock modulus and the strength parameters between iterations. Support pressures are computed by applying forces normal to the excavation surface. The approach is applied to the analysis of stability and support requirements for an entry in a longwall coal mine.

Jan 1, 1985

By M. J. Ferrante

The Bureau of Mines recovered rhenium powder from scrap tungsten alloy containing approximately 25 percent rhenium. Oxidation of the scrap at 950° C separated volatile rhenium heptoxide from tungsten trioxide. Minor amounts of tungsten, iron, and nickel were removed by selective precipitation from a rhenium solution from which was recovered crystalline ammonium perrhenate. Experimentation showed that hydrogen reduction of minus 325-mesh ammonium perrhenate at 1,000° C produced rhenium powder averaging 2.1 microns in size (Fisher Sub-Sieve method). The powder contained <50 ppm of total metallic impurities and 1,070 ppm of total interstitial impurities. Sintered compacts had a density of 95 percent of theoretical. Approximately 96 percent of the rhenium contained in the scrap alloy was recovered.

Jan 1, 1969

By E. J. Lintner

This paper is one of a series being prepared by the United States Bureau of Mines describing clay and shale mining and crushing methods and costs at various operations throughout the United States. These papers are designed to disseminate technical information regarding methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs may, in many instances, cause embarrassment to the individual operator as well as to the industry as a whole. On the other hand, it is essential to the technical discussion and study of methods employed to consider operating costs. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scone of the cost tabulations shale ensue. The open-pit recovery of clay and shale is a comparatively simple operation in comparison with underground mining; nevertheless, it represents an appreciable factor in the cost of manufacture.

Jan 1, 1936

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove, grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions 2 issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor; if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1970

By T. A. Sullivan

The processing of sweated aluminum electronic scrap was investigated to develop methods for recovering the aluminum and concentrating the other metals, including copper, lead, gold, and silver, into a product that can be separated by known methods. Two molten-salt electrorefining processes were developed and tested. The first process utilized a three-layer refining cell with a BaCI2-NaF-AIF3 electrolyte, which operated at 750° to 850° C. The second process used an all-chloride electrolyte of NaCI-KCI-AICI3 at 750° to 800° C, with separate anode and cathode compartments. High-quality aluminum was recovered that averaged 99.8-percent pure in the three-layer cell and 99.6-percent pure in the compartment cell. Over 94 percent of the aluminum was recovered with cathode current efficiencies of approximately 90 percent in both methods. The copper, lead, tin, silver, gold, and other metals were concentrated threefold in an anode product. Separation of lead and part of the tin by liquation from this product seemed feasible. The anode product was smelted to prepare a 96-percent copper bullion that contained 690 ounces of silver and 65 ounces of gold per ton, with 98 percent recovery of these values.

Jan 1, 1972

By M. Didyk

In this report, the application of the PHU/MVS program is demonstrated through the use of a simple but realistic mine ventilation program. The report details, the problem description, the input data required and the various output features of the simulator. The PSU/MVS program is written in Fortran IV for use with IBM 370/168 computers. A version of the program that can be used in CDC computers is also available. A ventilation network consisting of 531 branches, 300 nodes and 5 fans took 48 seconds for solution on The Pennsylvania State University&apos;s IBM 370/168 computer. Appendix I of this report is the User?s Manual for the program. Appendices II and III contain the input data listing, and selected output listing for; the application. Appendix IV provides tables for leakage, friction factors and shape factors.

Jan 1, 1977

By Charles D. Litton

An overview of state-of-the-art technology in fire detectors is presented by the Bureau of Mines regarding their use in the mining industry. Detectors are categorized according to the characteristics of a fire to which they respond. Operating principles of the various detectors, their application, and the advantages and disadvantages of each are discussed.

Jan 1, 1979

By Robert A. Elgin

The Leadville mining-district (fig. 1) covers approximately 8 square miles adjacent to Leadville, the county seat of Lake County, Colo. It is famous for its large production of rich ores containing zinc, lead, copper, gold, and silver. Some manganiferous ores also have been produced.

Jan 1, 1949

By Chas. G. Maier

The absence of plants on the Pacific coast for the reduction of iron ores usually is attributed to the fuel situation there. Thus, the bulletin of the. State Division of Mines for 1933, entitled "California Mineral Production," says: "There are considerable deposits of iron ore known in California, notably in Shasta, Mad era, Placer, Riverside, San Bernardino, and Los Angeles Counties, but production has so far been limited for lack of an economic supply of coking coal." It has been estimated that the six major steel plants of the Pacific coast have an annual ingot capacity of 600,000 tons. The present need for tin plate averages 300,000 tons yearly for California alone, of which some 12 percent is manufactured locally. If the consump¬tion of other iron and steel products in 1929 may be taken as an approximate, estimate of the normal requirement for such products, it may be estimated further that, 65,000 to 75,000 tons each of cast-iron pipe and steel reinforcing bars and 300,000 to 400,000 tons of structural shapes and plates will be required annually in California.

Jan 1, 1936

By S. J. Pearce

The need for a simple, very sensitive, and accurate method for the determination of benzene in blood and urine was evident throughout a recent study of chronic benzene (C6H6) poisoning conducted cooperatively by the United States Bureau of Mines, The Barrett Company, and the producers of benzene. A combustion method which will be described in a later publication, end a previously described5/ adaptation of Smyth&apos;s method were developed and used during that investigation. The adaptation of Smyth&apos;s method gave satisfactory results when dealing with exposure conditions that produced chronic poisoning in a comparatively few days, but it was time-consuming and lacked the accuracy necessary for a study of the absorption, distribution, and fate of benzene in the body during exposure to threshold concentrations of benzene vapor in air. The combustion procedure was satisfactory from the standpoint of sensitivity but was cumbersome, intricate, time-consuming, and required the use of special and somewhat expensive physical and. chemical apparatus. Following the termination of this study of chronic poisoning, possibilities for developing better methods occurred, and these have been investigated by the Bureau of Mines with the aid of Relief Works Division personnel. A microcolorimetric method for the determination of benzene in air has been described recently.6/ The present report deals with the adaptation of this new colorimetric method to the determination

Jan 1, 1936

By Lloyd Williams

1. The investigation shows that the Poplar Creek and Big Mary beds contain the largest known recoverable reserves of coal in Morgan County, Tenn. The Poplar Creek bed has been the most productive. 2. Known measured and indicated reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 96 million tons, as of January 1, 1954. Of this total, 59 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics were too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956

By F. E. Brantley, D. A. Martin

Synthetic zeolites were tried as selective adsorbents for recovering sulfur dioxide from synthetic gases and gases produced from gypsum decomposition . Initial adsorption tests , using the synthetic gases , indicated that three of these compounds , having sulfur dioxide capacities of up to 29 grams per 100 grams of adsorbent , were satisfactory . Regeneration studies showed that over 90 pct of the sulfur dioxide desorbed from the loaded beds was of sufficient purity for direct liquefaction . However , all zeolites tested lost adsorptive capacity with repeated use . The zeolite determined to be the most promising in the preliminary synthetic gas tests was also evaluated for capability in adsorbing sulfur dioxide from gases produced by the thermal decomposition of gypsum . Despite small amounts of hydrogen sulfide in the gypsum decomposition offgas , good adsorption of sulfur dioxide was attained . The economic practicality of utilizing zeolites for sulfur dioxide removal from industrial gases was not evaluated , but the technical feasibility was demonstrated .

Jan 1, 1963

By Duvall Wilbur I.

This is the second report to be presented on th application of stress analysis to underground Mining problems. In part I2/ of this investigation the stress distribution around single openings in unidirectional and hydrostatic stress fields was analyzed. Relationships between maximum stress concentration and size and shape of openings were determined by the photoelastic method. In most cases the results were verified by mathematical methods This report considers the stress distribution in pillars formed by two or more openings in a. unidirectional stress field. Relationships between stress concentrations and size and shape of pillars are developed. Applied to mining, results snow how estimates may be made of the stress distribution in pillars, what factors cause high local stresses, and how local stress concentrations may be reduced by proper design of mine openings. The photoelastic method was used, as in Part I, to study the stress distributions, and, whenever possible, the results were verified mathematically. A description of the photoelastic method and equipment is .given in Part I.

Jan 1, 1948

By Carl Belser

This paper, covering Chaffee, Fremont, Gunnison, Lake, Larimer, Park, and Summit Counties, Colo., is the second of a series reporting on the tungsten potential of the Colorado region. The assembled information was obtained by examination of some properties, personal contacts with owners, and access to unpublished reports by other engineers. The tungsten-bearing areas of the 7 counties cover approximately 400 square miles and are in 10 distinct areas, which vary in size (fig. 1) from 1 square mile up to 290 square miles. The tungsten mineral wolframite was discovered by a man named Hackay near Dale on the Florence & Cripple Creek Railroad in the early 1900&apos;s, and wolframite and hubnerite were noted at Climax and the adjacent areas in Lake and Summit Counties at an early date, but no records of shipment from any of the areas are available before World War II. It is not known when scheelite was first discovered, but it was recognized in the Stockton mine during World War I. In the counties listed 64 properties are known to contain tungsten; of these, 18 have had some commercial output, although only 3 of them produced in 1953. The total production through 1953 is estimated at 115,000 short-ton units of tungsten trioxide. In 1953 by far the major portion came from the Climax mine.

Jan 1, 1956

By Edward E. Johnson

The Bureau of Mines publishes in its ?Minerals Yearbook? a series of indexes on the domestic minerals industry. Among these are the index of physical volume of mineral production, indexes of stocks, and indexes of average unit mine value and implicit unit value, This report describes the material coverage of these indexes and the methods used in their construction. Detailed descriptions are given for several other mineral-oriented indexes regularly published by other government agencies. These descriptions give the index user a better understanding of what each index purports to measure and aids him in selecting the most appropriate index for his purpose.

Jan 1, 1965

By Edward E. Johnson

The Bureau of &apos;Mines publishes in its ?Minerals Yearbook? a series of indexes on the domestic minerals industry. Among these are the index of physical volume of mineral production, indexes of stocks, and indexes of average unit mine value and implicit unit value, This report describes the material coverage of these indexes and the methods used in their construction. Detailed descriptions are given for several other mineral-oriented indexes regularly published by other government agencies. These descriptions give the index user a better understanding of what each index purports to measure and aids him in selecting the most appropriate index for his purpose.

Jan 1, 1965

By S. C. Schaefer

The Bureau of Mines investigated tIle standard Gibbs energies of formation, 8Gfo, for MllF2 (manganese difluoride) and CoF2 (cobalt difluo-ride). High-temperature galvanic cells employing CaF2 (calcium diflu-oride) as the solid electrolyte were used to measure the open-circuit potentials for the cell reactions ?

Jan 1, 1985

As part of a continuing program of evaluating the Nation&apos;s crude-oil resource, this report presents information pertaining to resource, primary reserve, and potential waterflood reserve for 3,209 selected reservoirs contained in 24 oil-producing States, as of January 1, 1968. To that date the selected reservoirs had not been subjected to pressure-maintenance or secondary-recovery operations. These reservoirs also met the following parameters: (1) a minimum of five oil-producing wells on January 1, 1968, (2) a minimum of 50 acres areal extent, (3) a minimum of 50,000 bbl of oil ultimate primary recovery, and (4) the principal reservoir energy was other than active water encroachment. The selected 3,209 reservoirs produced 527 million bbl of oil in 1967, about 17 pct of U.S, total production. Primary oil reserve was 4,983 million stb; in addition, there was 6,043 million stb of potential water- flood oil reserve. Oil resource in the selected reservoirs was 59,547 million stb. A brief history and outlook of waterflooding are presented for each State. Depth and producing rate statistics and geologic distributions of production, resource, reserve, and potential waterflood reserve for the selected reservoirs are presented by States in the appendix. Also included in the appendix are description, history, and technique modifications of waterflooding, and a preliminary cost estimate of a closed-system water-injection project.

Jan 1, 1970

By James P. Bennett

To improve construction materials for emerging chemical and metallurgical technologies, the Bureau of Mines is investigating the acid resistance of ceramic materials. In the study described here, eight commercial ceramic materials comprising two red shale, two fire clay, a silica, a silicon carbide, a carbon, and a high-alumina brick were evaluated. Samples were exposed to 20 wt-pct HC1 at 50° C for 110 days. The test apparatus designed to evaluate the materials is described. Changes in chemical and mineralogical composition, cold crushing strength, volume, and weight, and leach rates of AI, Ca, Fe, K, Mg, Na, Si, and Ti ions were monitored. In general, the statistically significant physical property changes that occurred were small. In many cases, no changes were detected.

Jan 1, 1982