Search Documents

By J. N. Geyer

In coal mining it is essential to maintain the roof over working places and roadways in the safest condition possible. To this end every effort should be made to win the coal with the least injury to the immediate roof strata, as broken strata certainly present a greater hazard than a sound roof. The chief causes of injury to the roof in mining are inherent in the method of development and recovery and the blasting practices followed. The first, which may produce severe stresses in the roof, weakening it over comparatively large areas has been discussed in previous papers3 and will not be treated here. The second cause is local in effect, but with the same general method of blasting being employed throughout a mine having uniform roof conditions, similar effects on the roof may be expected. In the Bureau's investigation of accidents caused by falls of roof and coal it has been necessary to make a careful study of blasting practices and their effect on the immediate roof. The purpose of this paper is to show the effect of the observed methods of blasting on different types of roof and to point out methods that have been proved to be least harmful to the roof strata. The data used in preparing this paper have been compiled from reports made by Bureau engineers engaged in the study of falls of roof and coal, and embrace mines opened in the Pittsburgh coal in Ohio and Pennsylvania and the Pittsburgh and Sewickley coals in West Virginia.

Jan 1, 1933

By H. C. Hamontre

The liquid-level gage described in this report is an instrument designed to locate liquid levels in wells rapidly and accurately and, with auxiliary equipment described, to follow moving liquid levels automatically. The depth at which the instrument makes contact with the liquid in a well is indicated at the surface by a depth meter on the cable to which the instrument is attached. When the gage is used to follow a surging moving level, the liquid depth is indicated continuously at the surface. This report contains a description and illustrations of the gage and outlines the operating procedures. The instrument is 1-3/4 inches in diameter and approximately 6 feet in length and may be operated through 2-inch tubing. The gage consists essentially of a float that moves upward with respect to the rest of the assembly, causing a change in the flow of electric current from the surface when the liquid level is reached. The instrument has been tested under a variety of conditions and has been found to be sensitive to changes in liquid level of 1/2 inch. Its accuracy is limited principally by the accuracy of the wire-line depth indicator used. It is not affected by pressure or temperature, and it can be run in open hole or under pressure through a lubricator. It employs only one electric circuit and can be run on an Amergraph single-conductor cable (type 1-H-0) ,

Jan 1, 1954

By Virgil A. Marple, Susanne V. Hering

"5.1 IntroductionTraditional impactors do not offer much size resolution for submicrometer particles; typically their finest size cut is around 0.4 µ.m. Yet for many aerosol applications it is useful to be able to size segregate aerosols in the size range below 0.4 µ.m. Diesel emissions, welding fumes, cigarette smokes and photochemically generated smog aerosols typically exhibit mass median diameters between 0.1 and 0.6 µ.m. When sampling these aerosols with a traditional impactor, fifty percent or more of the aerosol mass can penetrate the final impactor stage. Allhough the material can still be collected on a backup filter, the filter gives no size resolution. As a result, the investigator has no size information on a substantial portion of the sample. One needs a sampler that size-segregates the majority of the aerosol mass. A lower size cut of 0.1 µ.m or less is required for most combustion smokes and smog aerosol s.To obtain smaller cutpoints two types of impactors have been developed, namely low-pressure impactors and micro-orifice impactors. Both instruments can provide cutpoints as small as 0.05 µ.m. Low-pressure impactors were introduced more than twenty years ago (Stem et al., 1962), and a variety of these samplers are in use today. Micro-orifice impactors have been developed at the University of Minnesota within the last five years (Marple et al., 1981 ). To date theirs are the only examples of these instruments in use.5.2 Operating PrinciplesThe low-pressure and micro-orifice impactors use two different approaches to achieve their very small particle-size cuts. Low pressure impactors resemble ordinary impactors, but are operated at reduced pressures of 5-40 kPa (0.05 - 0.4 atm). They take advantage of the decreased aerodynamic drag on particles that occurs when the mean free path in the air is as large or larger than the particle diameter. Micro-orifice impactors operate at near atmospheric pressure, but employ very small orifices, 40 µ.m to 200 µ.m in diameter. The streamlines of the air impinging upon the impaction plate have correspondingly smaller radii of curvature; the air is accelerated more quickly, making it more difficult for the particles to follow. The basic operating principles for both types of impactors are evident from the particle Stokes number, defined as:"

Mar 1, 1989

By P. L. Sibrell

Electrorefining of Ti in nonaqueous solvents has been studied by the U.S. Bureau of mines as a method for recycling impure scrap Ti. Electrochemical behavior of Ti species was investigated using cyclic voltammetry. Research results showed that Ti metal can be dissolved in polar solvents such as dimethylformamide or dimethyl sulfoxide. However, deposition of Ti from these solvents was not successful. Several solvent systems were investigated for electrodeposition of Ti but no deposits were obtained. Reduction of Ti4+ complexes to Ti3+ proved to be straightforward, but reduction to lower oxidation states could not be confirmed. In dimethylformamide solutions, cyclic voltammetry results demonstrated the reduction of Ti to an oxidation state of less than three, but no Ti metal was identified. In dimethyl sulfoxide solutions containing LiCl, it was possible to deposit Li metal. After adding Ti salts to the solution, electrolysis quickly passivated the electrode. Deposition of Ti was also investigated in solutions of dimethoxyethane and propylene carbonate but, again, no reduction of Ti to oxidation states of less than three occurred. Therefore, the prospects for a nonaqueous electrorefining system for Ti metal do not appear promising.

Jan 1, 2010

By Oliver C. Ralston, Foster Fraas

The electrostatic separation of solids utilizes the forces exerted when electrically charged particles of the solids are present in an electric field . The charges may be acquired by various means (5) , and when the acquisition or loss of charge depends on the property of the particle , separation can be obtained between particles having different properties . A property commonly utilized in present - day separators in conductance . Charging also may be accomplished by bringing the particles into intimate contact with various surfaces . This is sometimes described as a " frictional electrical effect. The charge , or specifically the polarity of the charge , in this latter case evidently depends on the property known as the contact potential , as has been explained in the discussion of a paper (7) and in several other papers (10) . Separation by this method is accomplished in two steps - a charging step , in which the particles are brought into intimate contact with an electrification surface , and a separation step , in which the charged particles are separated in an intense electric field . Descriptions of such methods may be found in the literature (2) , (7) , ( 8) . Even as early as 1909 , Blake and Morscher (2) described the charging of particles by intimate contact followed by separation in an electric field . They also state that the polarity of the electrical charge acquired by the particles depends on their composition . O'Brien ( 8) presented several designs of apparatus . He obtained electrification by means of a wiping action , either on inclined plates or in rotating cups , in which a centrifugal force was imparted to the particles .

Nov 1, 1942

By H. B. Brunot

The United States Bureau of Mines under provisions of Schedule 2C4 issues approvals covering complete operating units such as loading machines, room hoists, and storage-battery locomotives. Certain manufacturers design and build entire machines. Other manufacturers purchase a part or all of the electrical accessories from manufacturers of electrical equipment and make up permissible units by assembling them. Before the assembler purchases electrical accessories for use in such contemplated units he may require certain information from the accessory manufacturer as to whether the particular accessories are suitable for assembly in his proposed permissible outfit. To aid accessory manufacturers in marketing their product, a provision was incorporated in Schedule 20 whereby tests might be made on individual accessories and reports rendered as to the suitability of a given accessory for use in permissible assemblies.

Jan 1, 1935

By D. B. Taliaferro

[Recovery of core specimens from subsurface formations and their subsequent analysis are important aids in efficient development and operation of oil and gas fields. Core specimens first were obtained mainly for the geologic information they revealed; now they are analyzed to determine many of the physical characteristics and conditions of tae subsurface formations as well. Cores recovered from the producing formations may be analyzed for porosity, permeability, oil content, "connate" water content, and other physical and chemical properties of the formation, all to the end of furnishing enough data for making reliable estimates of the quantity and availability of oil and gas within a reservoir and in devising, efficient means for their withdrawal.]

Jan 1, 1939

By W. L. Crentz

Knott County is one of the smaller coal-producing areas in the Eastern Kentucky coal field. It contains numerous coal beds, many too thin to support mining over a wide area, Coal produced in the county is from a few rail-shipping operations and many small truck mines. Many smaller mines are working beds whose exact location in the coal-bearing strata is uncertain. Samples were collected from 11 different coal beds, of which the Fire Clay, Hindman, Upper Elkhorn No. 3, and Flag are the most import ant from a product ion standpoint. Known reserves in the Hindman bed. are very limited, and almost the entire production from this bed is gathered from two comparatively, large rail-shipping mines in addition to the four principal beds, samples were taken in the Francis, Haddix, Fire Clay Rider, Whitesburg, Amburgy, Upper horn No. 2, and Upper Elkhorn No. I .beds. Figure 1 is a typical section of the strata, showing the more important coal beds and. readily identifying their location with respect to each other. The bed names as shown are particularly important because of the local tendency to assign several names to the same bed. To avoid confusion, the names by which each coal bed is known also are given in the following listing. The coal. beds., in descending order, follow: [ ]

Jan 1, 1953

By J. W. Hunter, J. H. Jacobs

"Approximately 355 tons of nodules from Chamberlain; S. D., ore were processed in the 1-ton-per-day electrolytic-manganese pilot plant of the Bureau of lanes at Boulder City, Nev., in a continuous 3-month operation. The ore, ground to minus 48-mesh, was found to be amenable to leaching with acid directly or after roasting under reducing conditions in a Skinner muffled multiple-hearth furnace.Unroasted ore gave an acid-leach extraction of 84 to 88 percent of the manganese, which after neutralization showed an over-all extraction of between 81 and 85 percent of the manganese. The amount of iron extracted varied, but it was always,enough to permit the use of ammonia for neutralization.Roasted ore showed an acid-leach extraction of 89 to 91 percent of the manganese. A large amount of iron went-into solution, so that it was not economical to neutralize it entirely with ammonia. By neutralizing with calcine to a pH of 5.0 and completing -neutralization with ammonia to a pH of a.5 an over-all manganese extraction of 84 to 86 percent was obtained. The slight increase in. extraction on roasted ore probably would not justify the cost of roasting.Acid consumption averaged 1.75 pounds per pound of manganese extracted. Settling rates of the residue in leach solution were to slow to permit clarification in thickeners, but a Moore vacuum leaf filter proved to be satisfactory. Purification of raw leach solution was .accomplished readily by hydrogen sulfide with a low gas consumption. Electrolysis was normal, without difficulty, and with -current efficiency ranging between 62 and 66 percent.The use of Chamberlain modules for the production of electrolytic manganese would result in an operating cost of 0.8316 cent per pound higher than the cost of producing electrolytic manganese from Three Wids ore."

Mar 1, 1946

By C. Özgen Karacan

Longwall mining is an underground mining method during which a mechanical shearer progressively mines a large block of coal, called a panel, in an extensive area. During this operation the roof of the coal seam is supported only temporarily with hydraulic supports that protect the workers and the equipment on the coal face. As the coal is extracted, the supports automatically advance and the roof strata cave behind the supports. Caving results in fracturing and relaxation of the overlying strata, which is called "gob." Due its highly fractured nature, gob contains many flow paths for gas migration. Thus, if the overlying strata contain gassy sandstones or sandstone channels, gas shales or thinner coal seams which are not suitable for mining, then the mining-induced changes can cause unexpected or uncontrolled gas migration into the underground workplace. Vertical gob gas ventholes (GGV) are drilled into each longwall panel to capture the methane within the overlying fractured strata before it enters the work environment. Thus, it is important, first to understand the properties of the gas reservoir created by mining disturbances and, second, to optimize the well parameters and placement accordingly. In this paper, the production rate-pressure behaviors of six GGVs drilled over three adjacent panels were analyzed by using conventional multi-rate drawdown analysis techniques. The analyses were performed for infinite acting and pseudo-steady state flow models, which may be applicable during panel mining (DM) and after mining (AM) production periods of GGVs. These phases were analyzed separately since the reservoir properties, due to dynamic subsidence, boundary conditions and gas capacity of the gob reservoir may change between these two stages. The results suggest that conventional well test analysis techniques can be applicable to highly complex gob reservoirs and GGVs to determine parameters such as skin, permeability, radius of investigation, flow efficiency and damage ratio. The insights obtained from well test analyses can be used for a better understanding of the gob and for designing more effective gob gas venthole systems.

Jan 1, 2009

By Robert W. McKibbin

The Bureau of Mines conducted laboratory tests to determine the slurry transport and deposition properties of coal waste. A 188.5-ft pipe test loop was constructed with instruments to measure density, flow, and power and discharge, suction, and differential pressures. A 20-ton ample of Western coal waste was crushed and screened to 100 pct minus 1/2 in. Eight loop tests using this graded waste were run at slurry densities ranging from 1.15 (25 wt-pct solids) to 1.46 (60 wt-pct sol-ids) 0 The resultant friction-'pressure gradients ranged from 0,06 to 0.24 ft of water per foot of 4-in standard steel pipe. Particle-size degradation was significant.. In a typical loop test lasting 25 min, the minus 200-mesh fraction increased from 19 pct to 34 pct. Deposition tests showed that without the use of a flocculant, the slurries would not dewater when left to stand for 1 week. With flocculant, additional water was releas2d; however, the settled slurries remained thixotropic. Further testing is necessary to determine their suitability for use as backfill material in active mines.

Jan 1, 1983

By R. D. Govier

The U.S. Bureau of Mines has developed a thin-film X-ray fluorescence technique to rapidly determine Cu, Ni, Co, Fe, and Cr in super alloy leach liquors. Total analysis time per sample was less than 15 min, as opposed to several hours for traditional wet chemical methods. Precision and accuracy were checked by replicate analyses of solutions similar in composition to leach liquors, whose analyte concentrations were well known. Coefficients of variation for all elements were found to be less than 2 pet. With the exception of the results for Fe, all relative errors of estimation were also found to be less than 2 pet. Bulk liquids are not introduced into the spectrometer; thus, the potential for damage to the instrument by leakage of corrosive liquids is eliminated.

Jan 1, 1989

By C. A. Pearson, W. D. Dietzman, M. E. Hawkins

Results of chemical analyses and electrical resistivity measurements of 422 samples of oilfield brines from 120 east Texas fields in Railroad Commission of Texas Districts 5 and 6 are presented in tabular form . These samples represent water from all of the major petroleum- productive formations in the area . Water analyses and electrical resistivity data , when fully utilized by proper study techniques , are useful tools in the solution of many engineering problems such as detection of well leaks , identification of water sources , and interpretation of electrical well logs . In the area included in this study , these representative data should facilitate the solution of problems in which water analysis and water resistivity are factors .

Jan 1, 1964

By Larry A. Haas

The Bureau of Mines constructed a torsion effusion apparatus to measure the equilibrium vapor pressure of pure metals, alloys, and compounds at temperatures up to 1,500° K. The reliability of the apparatus was established by determining the vapor pressure of silver. The data obtained on solid and liquid silver in the temperature range 1,200° to 1,500° K can be expressed by the following equations:

Jan 1, 1965

By A. W. Khair, M. Ahmad, Gehi. L. D.

"This paper presents an analysis of the effect of the dynamics of bit wear on dust generation. Two surveys have been conducted in order to assess the mechanism and type of bit wear and to evaluate the impact of bit wear on the productivity of the continuous miners. Used bits were collected from the underground coal mines and these used bits were utilized in laboratory coal cutting. The effect of bit wear on dust generation has been quantified and its impacted on dust generation and ventilation system has been exemplified.INTRODUCTION Research has reduced the prevalence of Coal Workers Pneumoconiosis from 15 to 5 percent according to NIOSH reports (Breslin 1982). However CWP still have not been eliminated as a hazard to mine workers. To prevent coal workers from having black lung MSHA has established a very strict standard for coal mine operations (2.0 mg/m3 with silica content equal to or less than 0.1 mg/m3,). There are numerous coal operations still experiencing great difficulty with meeting the 2mg/m3 dust standard. Among these are the longwall sections and continuous mining sections. In order to meet the rising demand of energy and coal, the number of longwall operations and continuous mining operations would have to be increased. Thus a long term research commitment is required to develop basic solutions that are more generic and greater benefit to the mining and mineral industry.In continuous-mining operations, the miners are exposed to the dust produced during the fragmentation of the coal from the face plus the dust produced during loading and transferring of the coal. The fragmentation process generates most of the respirable dust. The amount of dust generated during fragmentation depended on the coal properties, cutting parameters and cutting bit configuration. Bit wear changes bit configuration, therefore, it also affects dust generation. Bit wear can be defined as the removal of material from surface as a result of mechanical action. In soft coal mines bit wear may not be a serious problem but in hard coal seams bit wear is very significant. In addition, as the good coal seams are depleted, the operators are mining thin seams and the seams with rock partings. During cutting these seams operators are sometimes forced to cut roof and floor rock or rock partings which result in more rapid wear of bits."

Nov 1, 1995

By James L. Fenton

In its unending search for the raw materials that the affluent society of today requires the mining industry has found it necessary to go to great depths, in many cases, to produce these materials. Inherent with this problem is the insufficient technology relating to improving extreme environments that the mine personnel are exposed to. In this dissertation, the sources of heat flow into a mine along with the various effects that this heat has on the mine personnel are investigated. The object of dissertation is to compile all the available published information pertaining to these underground heat and their effects into one paper. This will provide the mining industry with an available easy-to-use to aid in the determination of mine ventilation requirements as the mines are in the phases of original planning or being extended to depth. Areas of significant, deficiencies it knowledge have been disclosed during this overall appraisal. Recommendations on important basic research needs are out lined for future consideration by Federal or industries sponsorship. This thesis should serve as a stimulus lo, future well-organized research efforts in the area of underground heat sources and their control.

Jan 1, 1973

By W. W. Adams

The quantity of explosives sold in the United States in January, 1931, for domestic consumption, amounted to 368,100 kegs (9,202,500 pounds) of black blasting powder, 4,610;000 pounds of permissible explosives, and 16,533,000 pounds of high explosives 'other than permissible. These figures are based on reports received by the United States Bureau of Mines, Department of Commerce, from nearly all manufacturing companies, and include an estimate of sales by several companies that do not furnish monthly reports. Reports actually received from manufacturers showed soles of 365,977 kegs of black blasting powder (consisting of 220,892 kegs of granular powder and 145,085 kegs of pellet powder), 4,687,900 pounds of permissible explosives, and 15,496,152 pounds of high explosives other than permissible. Sales in January, 1931, were smaller than in January, last year, the decreases being 14 per cent for black blasting powder, 19 per cent for permissibles, and 17 percent for high explosives other than permissible. Sales in January 1931 when compared with soles in December 1930, show increases for all three classes of explosives as follows: 2 per cent for black blasting powder, 16 per cent for permissible explosives, and 7 per cent for other high explosives.

Jan 1, 1931

By D. Harrington

The number of fatalities from mine explosions for the fiscal year 1945 dropped below that of the year before; continued improvement over the record of the years from 1940 to 1945 is hopeful, but the number of reported explosions has increased rather than diminished, and the number of victims claimed by explosions is often more definitely a factor of chance than forethought. Mine fires and explosions can be eliminated through the methods now well-known to those well-informed in matters pertaining to safety in mining but ignored by many coal-mine operators and employees who follow procedures of the past or their own short cuts, regardless of disasters that may result: Tried and proved safety measures for preventing mine fires and explosions have been recommended to the mining public repeatedly, yet only a relatively small but far-sighted minority have adopted these measures and made them a part of operating practice. That far more explosion disasters did not occur in 1945 is fortunate. In 1945 a coal-mine fire of electrical origin caused heavy loss of life, while several others from the same cause were controlled with but few fatalities; this hazard is now being curbed temporarily to some degree after the bad record of the two preceding years, but a real solution of the problem has not been reached, although cooperating committees trying to produce at least some answer have made progress.

Jan 1, 1946

By Dennis J. Grigal

The objective of this contract was to monitor operating conditions of, four flooded, fibrous-bed filter panels used during normal underground mining operation and to analyse clogging and structural problems. After observing structural and clogging problems and conducting laboratory and field tests, a final, Flooded, fibrous-bed filter design which minimizes clogging and structural problems was recommended to the Bureau of Mines. This report also describes the dust sampling procedures used to determine the dust concentration at the flooded, fibrous-bed scrubber intake duct.

Jan 1, 1979

By G. Asai

The purpose of this Bureau of Mines investigation was to determine the properties of arc-melted iron-chromium alloys ranging in chromium content from 12 to 50 wt.-pct. Alloys were prepared by consumable-electrode arc melting of electrodes composed of high-purity chromium and high-purity iron. Alloys were fabricated to rod and sheet, and the following data were obtained: Electrical resistivity, hardness, tensile strength, and impact strength at room temperature; and creep-rupture life at 650° C. (1,200° F.). As the chromium content of the annealed alloys varied from 12 to 50 pct., the properties varied as follows: The electrical resistivity increased proportionally from 41 to 53 microhm-cm,; the Rockwell hardness varied from A 38 to A 58; the tensile strength ranged from 52,000 to 96,000 p.s.i.; the impact strength of V-notched charpy specimens varied from 140 to 405 ft.-lb., and the 100-hour creep rupture life at 1,200° F. varied from 5,000 to 16,000 p.s.i.

Jan 1, 1962