Search Documents

By Thomas M. Barczak

The Bureau of Mines is conducting research to optimize the capability of mine roof supports so that the selection and design of these supportsare compatible with the conditions in which they are to be employed. This report describes a study that investigates three parameters influencing the load-carrying capability of wood crib supports: height, configuration, and horizontal displacement. Four crib heights, four parallelogram configurations, and three ratlos of horizontal-to-vertical displacements were tested on full-scale wood crib supports in a mine roof simulator. Test results indicated a reduction in load-carrying capability for increases in crib height. Increasing the contact area by changing the intersecting angle between crib blocks to form parallelogram configurations provided a slight increase in load-carrying capability for the first 10 to 12 in of vertical convergence, after which the cribs became more unstable, resulting in significantly less load-carrying capability. Horizontal displacements did not appreciably affect the load-carrying capability of wood crib supports for the range of vertical displacements (less than 10 in) likely to be encountered underground. This report documents these tests and postulates some explanations of failure mechanics for the observed behavior.

Jan 1, 1988

By R. E. Siemens

The Bureau of Mines sought to correlate the variation of structure-sensitive superconducting properties with microstructure in selected Cb-Hf alloys and to compare the experimental results with those predicted by the GLAG theory. Alloys in wire and rod form were evaluated by critical temperature, critical current, magnetization, resistivity measurements, and optical and electron microscopy. In the absence of an external magnetic field, the current carrying capacity of columbium was greatly reduced with addition of up to 85 wt pct Hf, but a large increase in Ic occurred for Cb-90 wt pct Hf. Favorable Ic-H behavior was observed in cold-drawn alloys containing 25 and 57 wt pct Hf. Correspondingly, a maximum in Tc occurred at 10-25 and 90 wt pct Hf. Four- or five-hour heat treatment at 600° C resulted in maximum Ic values and maximum hysteresis in magnetization. Dislocation pileup, polygonization, and fine precipitates, responsible for flux pinning, are listed in order of their effectiveness as pinning sites. Sites having an average separation of 1,500 to 3,000 A and a diameter of 1,000 A or less were most effective in influencing Ic-H and M-H behavior. The resistive critical fields increased smoothly to a maximum of 80 k0e between 60 and 65 wt pct Hf. Highfield, mixed state, reversible paramagnetism was observed in some alloys; however, the GLAG theory was in good agreement with experimental results for the majority of the composition range studied.

Jan 1, 1969

Bag stackers who use semi-automated palletizing machines and air slides may be exposed to high concentrations of dust. To reduce dust exposure, use an exhaust ventilation system in conjunction with an envelope of clean air over the bagstacker provided by an overhead air supply. Description of Hazard Mineral processing plants in the United States and throughout the world process material that is finely ground and placed into bags for shipping to the consumer. These bags normally range from 50 to 100 pounds in weight. Once the material is placed in these bags, a bag stacker loads the bags onto pallets. A bag stacker is exposed to a lot of dust that is mainly released by the force from loading the bag onto the pallet. The two main sources are the dust on the outside of the bag and the dust that escapes from inside the bag as it is loaded. The Mine Safety and Health Administration's (MSHA) records indicate the bag stacker's dust exposure is one of the highest of all workers at mineral processing operations. Ways to reduce the dust exposure and strain to the bag stacker are in constant development. Recently, automated systems have been built. These systems range from fully automated, which totally remove the worker from the bag-stacking process, to semiautomated systems, in which the bag stacker still performs some of the functions. This Hazard Control deals with controlling the bag stacker's dust exposure during use of a semi-automated palletizing machine. The worker slides the bags into position on the palletizing machine. Once an entire layer of bags is positioned, the bag stacker operates the controls on the palletizing machine to lower the layer of bags onto the pallet. An air slide is built into the semi-automated palletizing machine so the bags are easier to move. This slide uses a metal table with air jets that exit through small holes at high velocities, similar to an air hockey game. The dust problem occurs because the air slide causes dust to blow up onto the bag stacker, significantly increasing the dust exposure.

Jan 7, 2001

By G. Richards Gwinn

In modern warfare, mica is truly indispensable. Coordination of combatant units necessitates maintenance of intricate communications equipment, in the construction of which high-grade sheet mica is essential. Scrap, ground, and the poorer qualities of block mica, which are less essential to the military program, are not considered in this paper. Furthermore, as the paper is designed primarily to assist mica miners, mica derivatives, Such as splittings and films, also are excluded from discussion. The paper therefore relates solely to block mica of strategic quality. Understanding of t e many factor involved in marketing mica is definitely advantageous to mica, miners. The nature and detrimental effects

Jan 1, 1943

By L. A. Morley

Volume IV of the final report examines the problem of indirect contact of overhead high-voltage power lines by mining personnel. This refers to the contact of energized lines by workers through some intermediate conductor such as a metallic tool or a piece of high-reaching mobile equipment, thus the term "indirect contact." The shock hazard presented by such contact has been a major cause of electrical fatalities associated with mining operations. The report volume is divided into three major areas. The first gives a general background of overhead lines, basic characteristics, and associated hazards, and continues to describe presently used techniques and devices which attempt to alleviate the contact problem. The second area narrows the discussion to the mining industry by presenting a detailed analysis of 39 overhead-line contact accidents in mining since 1970. The third major section uses the information from the first two areas to formulate recommendations to prevent these accidents and subsequent electrocutions at mining operations.

Jan 1, 1982

By K. C. Dean

During the investigation of the occurrence of manganese deposits in western United States, the Bureau of Mines collected 2-ton samples from three oxide manganese ores in the Columbia and Elberta Mining Districts, Tooelo and Juab Counties, Utah. To determine the amenability of these ores to standard ore-dressing methods: of concentration, extensive laboratory tests were made. The Wildcat property, one of those sampled, is 7 miles east of Fairfield, Tooele County, Utah. The ore is described as a replacement deposit and occurs along fracture and bedding planes of shale and limestone. Experimental work was done on a sample taken from a stockpile at the mouth of the shaft. The Wildcat manganese ore is intermediate in grade (25.7 percent manganese) and contains clay as the principal gangue constituent. A high-grade product was obtained with high recovery of Manganese by simple washing.

Jan 1, 1949

By S. M. Shelton

Preliminary work in the investigation of electrolytic manganese, as reported J, showed promise for a practical procedure of continuous production. Laboratory work was continued in the direction of process simplification to determine an economically feasible procedure that mould require a minimum of expensive equipment for plant erection and a minimum of regent consumption for operation. Results furnished enough evidence to indicate that modifications of the process could be made leading to simplified procedure and with no sacrifice in operating efficiency. A supply of at least 200 pounds of the metal was desired for alloy research, and it was believed worth Mile to utilize available facilities in a search for difficulties, that were not encountered in the laboratory and that might arise in larger-scale operation. Consequently, an experimental pilot plant was erected. The plant was designed for a capacity of 15 rounds per day of metal and operated under simulated -plant practice.

Jan 1, 1938

By Walter E. Lewis

A mothod of cutting St. Poter sandstono by streams of water under pressuro from nozzles and pumping the resulting, sand to the surface has roduced the cost of storm-sowor construction in the Minneapolis-St. Paul aroa. The hydraulic tunneling method, has boon in uso since 1934, and it is adaptable only to the lower part of tho St. Potor, sandstone, which lios within or just abovo the ground-wator levol. Tho upper part of the formation, immediately bolow tho Plattoville limestone, 18 comonted and camot bo mined by hydraulic mothods. The tunnel oporation observed in this instance is a main storm sowor starting at tho Mississippi Rivor below the 10th Avenuo SE bridge and will be drivon 6,000 foot at a grado of 1 foot por thousand undor the city of Minneapolis to Konnody and Arthur Stroots NE. A lateral storm sowor, which branchos from the main sovor at 8th Street SE, will oxtond from 10th Avonuo SE to 15th Avonuc SE. Tho tunnele are being drivon with the floor approximately at ground-wator lovol. All waters ontoring the main storm sower vill drain into the Mississippi Rivor. Tho main storm sewer cross soction is excavated to a roughly hox- agonal shapo 10 foot high by 10 foot wido at the contor. The upper half of the tunnol soction is solidly lined with either timber or stool. After all oxcavation is completed, the tunnel will be finished with a concrete circular lining 8 feet in inside diameter. The lateral storm sewer is excavated to a 5-1/2-foot by 7-1/2-foot section and will event- ually be finished with concrete to a modified horseshoe-shaped section 6 feet by 4 feet. Where the back or walls are considered unsafe during excavation, the upper half of the tunnel is lined solidly with timber. The equipment used by the Sower Division, City of Minneapolis, has been selected to meet a number of applications in storm-sewer work with diversified usage in mind. The sand pumps used on this job are rubber-lined, designed to work against a head of 100 foet. Either 4-inch or 6-inch diameter suction and discharge openings may be used. Other equipment, such as pipe, mine rail, flexible hoses, compressors, and general surface shop equipment, is drawn from a contral warohouse. It may be either new or used, depending on what is available at the warehouse. Much of the pipe and mine rail has been used for many years on several different tunnol jobs.

Jul 1, 1950

By Clayton A. Landsidle

There has been little change in timbering methods in anthracite mines for 75 years, and technical information on strata control is almost wholly lacking. In order to assist the industry to establish technical data, the Bureau of Mines and a Northern field operator are cooperating in underground experiments, the first phase of which has been to investigate pneumatic packing. The four principal methods of packing in mining are hydraulic, pneumatic, mechanical, and hand. The hydraulic pa caring system is believed to have originated at Shenanodah, Pa., in 1864,4/ to prevent destruction of a church by surface subsidence after underground coal mining. This method was used again in 1884 to arrest an underground fire at Buck Ridge colliery, near Shamokin, Pa. In 1901 hydraulic packing was introduced to Europe in Upper Silesia, where it gained in popularity owing to the availability of large quantities of sand suitable for flushing .5/ Hydraulic packing has a number of disadvantages. Chief among these are the softening effect of large quantities of water on the mine floor conducive to heaving action; drainage and punning costs; and the inability to fill roof cavities completely in flat beds.

Jan 1, 1953

By John K. Owens, Wayne L. Howie

Mobile roof support (MRS) machines are used as roof support during pillar recovery in retreat operations in lieu of wooden posts, cribs, or hydraulic props. A Mine Safety and Health Administration-permissible load rate monitoring system was developed for the MRS by researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health. The system uses a dedicated embedded processor to monitor changes in pressure inside the hydraulic cylinders of the MRS through multiplexed data acquisition channels and converts these pressure changes to load rates that sequentially activate three load-rate-indicator lights mounted on the machine. Each light represents a different loading rate to alert mine personnel to dangerous conditions during pillar extraction.

By Peter Grandone

Steel and iron pipe lined with cement to protect it against corrosion has been used in the municipal water systems of the New England States since about 1870. In most recent years, the petroleum industry adopted cement-lined pipe to forestall corrosion, particularly in those areas where large quantities of corrosive brines and hydrogen sulfide are associated with the oil produced. Many of the oil companies had on hand large quantities of corroded pipe, normally disposed of as scrap, which could be cleaned, lined with cement, and returned to service. It was soon learned that after the so-called scrap pipe was lined with cement much of it could serve fully as well as new cement-lined pipe. The demand for lining used pipe with cement resulted in the establishment of several processing, plants in the Mid-Continent oil-producing area. Today six cement-lining plants serve the areas three in Oklahoma and one each in Kansas, Texas, and Illinois. All of these plants have lined large quantities of used pipe for the brine-disposal systems of western Kansas, Illinois, and east Texas and also for the operators of water-flooding projects in northeastern Oklahoma and southeastern Kansas, where large quantities of brine and fresh water are being injected into the oil-bearing formations as a secondary oil-recovery method. Since war demands during the past 2 years have created an acute shortage of steel, the need of reclaiming used pipe for the expansion of oil-producing operations has become more evident than ever before. Thus the new industry (about 6 years old) - lining used pipe with cement - is saving large quantities of steel at a critical time by reclaiming used pipe and preventing further- corrosion.

Jan 1, 1945

By E. V. Cilento, K. A. DiGregorio, R. C. Lantz

"DIGREGORIO, K. A., E. V. CILENTO, AND R. C. LANTZ. A kinetic model of superoxide production from single pulmonary alueolar macrophages. Am. J. Physiol. 256 (Cell Physiol. 25): C405-C412, 1989.-A kinetic model was developed to describe the production of superoxide (02) by single pulmonary alveolar macrophages (PAM). Model predictions were compared with experimental results obtained from single rat PAM. The 02 was quantified by measuring the reduction of nitro blue tetrazolium (NBT) to a diformazan precipitate (NBTH,) from video-recorded images of individual cells. The kinetic model considered three reactions: 1 ) the production of extracellular 02 from the reduction of oxygen by NADPH oxidase using intracellular NADPH as the substrate, 2) the subsequent dismutation of 02 to form H,O,, and 3) the reaction of 02 and NBT to form diformazan. NBT specificity for 02 was analyzed by comparing results in the presence and absence of superoxide dismutase (SOD) that catalyzes the dismutation of 02 to H,O,. Measured PAM heterogeneity was accounted for by varying the concentration of intracellular NADPH, its rate of depletion, and the concentration of intracellular NADPH oxidase in the kinetic model. Model predictions compared favorably with experimental results except when SOD was present. This discrepancy may be due to diffusional limitations because NBT is a relatively small molecule (818 mo! wt) compared with SOD (34,000 mol wt). In addition, the cell surface is both ruffled and negatively charged, which may introduce steric hindrances and/ or electrostatic effects, since SOD is also negatively charged, whereas NBT is positively charged.PULMONARY ALVEOLAR MACROPHAGES (PAM) protect the lungs by phagocytizing foreign debris and bacteria. This process is accompanied by the production of superoxide anion (02) at the surface of the plasma membrane (3, 31). Superoxide readily dismutates to form H20 2 and subsequently, other oxygen metabolites which have been shown to be both antibacterial and cytotoxic (21, 25, 35).Superoxide is produced from the reduction of extracellular O, at the surface of the cell membrane by NADPH oxidase by the following reaction (3, 4)"

Jan 1, 1989

By Alexander L. Peyton

The Magruder and Chambers copper deposits in the Little River gold district, on the border line of Lincoln and Wilkes Counties, Georgia, have been known for a number of years (fig. 1). The Magruder deposit was first opened as a gold mine but has produced mostly copper and load. Records show that about 50 cars of concentrates were shipped from this property. No record of any production at the Chambers deposit is available. The Bureau of Mines, in its program of investigation of strategic minerals deposits, diamond drilled 10 holes, totaling 3,784 feet, on the two properties between December 3, 1948, and June 23, 1949. Eighty-eight core samples were analyzed, and the analyses and drill-hole data are presented in this report.

Jan 1, 1950

By Bernard Porter, E. A. Brown

Electrical conductivities and densities of the LiF- UF , LiF- ThF4 , NaF - C1F4 , and NaF - ThF systems were measured as functions of composition and temperature . The specific conductance and density varied linearly with temperature . Molar and equivalent volumes , as well as heats of activation for conductance , were calculated from the experimental data . At 1,000 ° C , the molar volumes ranged from 16 to 40 cubic centimeters per mole and the specific conductance ranged from 9.8 to 2.5 per ohm- centimeter as the actinide metal fluoride concentration changed from 0 to 60 mole - percent . Heats of activation for conductance were 3 to 7 kcal per mole . The data are interpreted on the basis of a semilattice model for the melts .

Jan 1, 1964

By H. H. Schrenk

The purpose of respiratory protective equipment is to prevent the inhalation of harmful or objectionable atmospheres. Although constituents or contaminants that may render an atmosphere irrespirable or objectionable are numerous, they may be classified broadly as follows: I. Gaseous substance: n. A. Toxic. B. Inert (oxygen deficiency). II. Particulate matter (dispersoids). A. Solid. a. Dust (formed by disintegration). b. Pure (formed by condensation). B. Liquid. a. Mist (formed by disintegration). b. Fog (former by condensation).

Jan 1, 1940

By John A. Johnson

"INTRODUCTION The use of wet drilling with adequate ventilation has largely controlled production of dust in drilling rock; however, in some operations, such as shaft sinking and modern tunnel driving, when each of a number of drills is operating in a small cross-sectional area, it is at times difficult to ventilate well enough to keep the dust concentration within desired limits.Some chemical compounds, known as wetting agents, when added to water in small quantities reduce the interfacial tension and make it possible for the solution to wet dust particles more effectively than water alone.This report presents results of tests on the effectiveness of two wetting solutions in reducing the amount of dust produced by wet drilling in basalt.ACKNOWLEDGMENTSThe tests were conducted the Bureau's Mount 'Weather Testing Adit,Mount Weather, The author acknowledges the assistance and cooperation of Wing G. Agnew, superintendent; Marvin M. Revelle, mining-engineering aide; and the rest of the crew at Mount Weather in conducting the tests. C. W. Owings, mining engineer, Safety Division, assisted in conducting some of the first tests and gavel valuable advice and guidance throughout the work and in preparing this report."

Jan 1, 1943

By Seth T. Reese

THE INJURY DATA and experience at coal mines in the United States for 1949 are presented in this bulletin under the following general sections: (A) General injury experience: 1. Tables 1 to 18: Contain current data on number of injuries, frequency and severity rates, average severity, major and detailed classification of injuries, and distribution of injuries by part of body and days of disability. (B) Selected injury data: 1. Tables 19 to 45: Contain current data on various selected factors of operating and physical conditions that have contributed to the occurrence of injuries at bituminous-coal mines and at Pennsylvania anthracite mines. These factors include extent of hand and machine loading, size of mine by employment and production groups, thickness of bed or vein, duration and number of work shifts, rating of mine as gassy, or nongassy, types of cap lamps, ventilation, explosives, and combinations of factors that influence mine safety. (C) Injury experience by States: 1. Tables 46 to 52: Contain current data on number of injuries, frequency and severity rates, average severity, major classification of injuries, injury records of all coal-producing States, and the relative standing by States according to injury-frequency rates. (D) Appendix: 1. Tables 53 to 84: Contain certain injury data for the years 1943-47 that have not heretofore been published.

Jan 1, 1953

By Michael J. Brnich

During the past 15 years the number of reportable mine fires has declined. A decline in the number of reportable fires is a gross indicator that allows experts to say something about the underground coal industry generally: There has been some improvement in overall mine fire preparedness. However, such an indicator is less reliable as a predictor of readiness at any particular operation. An indication of fire fighting preparedness would have to be assessed from evidence gathered at the mine site. In other words, there are two levels from which to view the problem. On a general level, there has been significant improvement in the industry's fire response capabilities over the past two decades. Specifically, however, little data has been gathered on a site-by-site basis to determine what improvements might be made on a local level. These improvements would move beyond regulatory compliance. It is expected that this manuscript, based on work conducted at an underground coal mine in the western United States, will help to focus attention on some central concerns involving this critical issue.

Jan 1, 2006

By Steven J. Page

Accurate measurement of workplace respirable dust concentration is an essential step in eliminating lung disease in any occupational setting. In the United States (U.S.) coal mining industry, this measurement process has relied upon a personal sampler that includes a 10 mm Dorr-Oliver (DO) nylon cyclone operated at a flow rate of 2.0 L min-1 to collect a respirable dust sample. Dust concentrations measured with this sampler are multiplied by 1.38, which was empirically derived, to convert them to measurements approximating the United Kingdom British Medical Research Council (BMRC) definition of respirable dust upon which the health effects of coal mine dust are based. The International Organization for Standardization (ISO) subsequently refined the respirable dust definition and the U.S. National Institute for Occupational Safety and Health (NIOSH) 1995 Criteria for a Recommended Standard presented a conversion multiplier of 0.857 to apply to the 2.0 L min-' DO (in addition to thel.38 multiplier) to obtain equivalent ISO concentrations, as approximated by the 1.7 L min-1 DO. However, the conversion multiplier 0.857 was derived indirectly from a limited size distribution data set rather than a direct comparison of the DO samplers. The present analysis focuses on providing a more accurate conversion multiplier derived from direct comparisons of the 2.0 L min-1 (with 1.38 BMRC equivalency multiplier) and 1.7 L min-1 DO cyclones. A weighted linear regression analysis of this database suggests that a more accurate estimate of the conversion multiplier is 0.815.

Jan 1, 2009

By P. R. Perry

This publication is a compilation of tested methods for the analyses of titanium tetrachloride, titanium sponge, and various intermediate materials and products. They are presented in concise form without the detail usually found in publication of new methods because many of them are modifications of well known procedures. The Electrometallurgical Experiment Station, Boulder City, Nev., has been developing titanium production methods since 1945. Most of this development was on a modified Kroll Process but also included work on sodium reduction and electrolytic methods. During these years a large variety of samples were analyzed. Most of the analytical problems were solved using published methods or modifications of the same. At the start, there were no published procedures for analyzing titanium sponge using spectrochemical methods. A great deal of study was given to testing several of the well known techniques, and some of them, such as direct sparking of the metal, proved to be completely unsatisfactory. Solution-spark techniques were finally tried, and satisfactory procedures were developed for some of the more common impurities. These spectrochemical methods were then put into routine use for several months before their publication.2/ Some new modifications have been made, and techniques have been developed to determine other impurities found in titanium sponge and tetrachloride. All spectrochemical methods used in 1954 are included in this publication.

Jan 1, 1955