Search Documents

By Charles B. Kenaban

The possibility of using ultrasonic energy as a tool to improve the electrolytic deposition of copper and zinc from several electrolytes was investigated by the Federal Bureau of Mines. Sound with frequencies of 20, 26, 38, and 400 kilocycles per second and acoustical intensities of 0.25 to 1.5 watts per square centimeter was employed. Measurements of cell voltage, anode and cathode current efficiencies, and electrode potentials were made at various current densities. Effects of ultrasonics on the quality of the deposit and on anode corrosion also was noted. In the electrolytic recovery of copper from an acid copper sulfate solution at 50° C., adherent, well-consolidated deposits are normally obtained up to a current density of 30 amperes per square foot. As the current density is increased above this value, the deposits normally become progressively more spongy and less adherent. Ultrasonic irradiation resulted in adherent and well-consolidated deposits at current densities up to 300 amperes per square foot. Radiation also produced smaller grain size and preferred orientation of the copper crystals. In addition, radiation caused as much as 3-volt decreases in cell voltages at the higher current densities. These decreases were caused chiefly by depolarization of the anode, although small depolarization effects were also noted at the cathode. Radiation apparently did not greatly affect cathode-current efficiencies, but prevented excessive anode corrosion at the higher current densities and resulted in more uniform corrosion. Ultrasonic radiation at a frequency of 400 kilocycles per second was not as effective as radiation at the lower frequencies. Circulation of the electrolyte at rates up to 5 percent of the cell capacity per minute did not produce results comparable to those effected by ultrasonic radiation. Rapid rotation of the cathode up to 1,800 revolutions per minute gave results approaching those obtained with ultrasonics.

Jan 1, 1961

By G. M. Kintz

The data in this circular were taken from publications of the United States Bureau of Mines and published annual reports of the Wyoming State Inspector of Coal Mines. The tables included are complete only' with regard to major disasters; the Bureau of Mines considers a major disaster one in which 5 or more men are killed. However, minor disasters and gas ignitions recorded in these publications are included. It is known that a number of gas ignitions have occurred of which no record is available. This is one of a series of papers by the Bureau of Mines giving by States available data regarding coal-mine explosions. This information is published in condensed form in the belief that it may be of vale to mine operators in preventing future coal-mine explosions.

Jan 1, 1934

By J. M. Goris

The U.S. Bureau of Mines, in a cooperative project with the University of Utah, Salt Lake City, UT, and Homestake Mining Co., Lead, SD, conducted in situ monitoring and numerical modeling of rock masses supported with cable bolts in two mechanized, cut-and-fill stopes and a shaft pillar at the Homestake Mine. Extensometers were used to measure rock displacement, while cable bolt strain gauges were installed to measure loads on both conventional and birdcage cable bolt supports. These instruments provided an assessment of rock mass behavior during mining as well as essential data for verifying results from computer analyses. The numerical modeling program FLAC was used to analyze cable bolt patterns and supports. Results from the evaluation study indicated that cable bolt strain gauges and extensometers were effective instruments for monitoring the behavior of rock masses supported with cable bolts. Also, numerical modeling of the 4S-48N stope using the FIAC code provided displacement values comparable with measurements from field extensometers.

Jan 1, 1993

By Joseph A. DeCarlo

This publication presents statistical data on oven-and beehive-coke plants in the United States. Information on the carbonizing capacity of the coke industry is important because of the close relationship between the coke industry and most of the other basic industries of our country. Coke is an essential-raw material in pig-iron production; also, coal-chemical materials are used to make fertilizers, paints, plastics, synthetic rubber, explosives, detergents, nylon, pharmaceuticals, dyes, and many other useful products necessary to sustain and improve the high standards of living in our country. Oven-coke plants in the United States on December 31, 1958, are tabulated in table 1. This tabular presentation shows the location, classification, number and type of ovens, annual coke capacity, coal chemicals produced, and name and address of parent company for each individual coke plant. About 86 percent of the capacity of slot-type coke ovens in the United States is owned by iron and steel companies. In most of these plants the coke ovens are integrated with the blast furnaces to facilitate transportation of raw materials for steel making. This has resulted in large coke plants, and the average annual coke capacity of "furnace" plants in 1958 was 1.3 million tons. Nonfurnace or "merchant" plants include coke plants associated with chemical operations, gas utilities, as well as coke plants that produce metallurgical, industrial) and residential-heating grades of coke and coal-chemical materials for sale on the open market. These plants ordinarily are not as large as furnace plant~ and annual coke capacity of merchant plants in 1958 averaged only 500 thousand tons. At the end of 1958 there were 55 furnace plants and 22 merchant plants.

Jan 1, 1959

By A. S. Moore

The Bureau of Mines is doing research and development work on removing acid-gas impurities from synthesis gas made directly from coal. Since conventional gas scrubbers, packed towers and bubble-cap columns, are expensive to construct and difficult to operate with viscous solutions, one aspect of the work was developing a compact, agitated, gas-liquid contactor for use with concentrated absorbents. The efficacy of the agitated contactor for absorbing carbon dioxide in diethanolamine increased with increasing solution rate, turbine speed, diethanolamine concentration, and carbon dioxide concentration in feed gas, and with decreasing liquid-gas ratio. It was unaffected by pressure between 200 and 300 p.s.i.g. and little affected by temperature between 115 and 190° F.

Jan 1, 1961

By William F. Jahn

Because of the' situation in Europe during the summer of 1939, with the possibility of war and consequent curtailment or loss of supplies of tin to the United States, the Bureau of Mines undertook an investigation of domestic tin resources. This was permitted by the Strategic Minerals Act of 1939, which authorized investigation of possible domestic resources of strategic minerals necessary in a national emergency. The minerals selected were in short supply, and the United States depended almost entirely on imports to meet normal requirements. The Black Hills of South Dakota were selected for investigation as one possible source of tin because of the occurrence of the mineral there has been known since 1876, although production had never been important. The Tinton area, in the northern part of the Hills, had received the most attention and contained some minor indicated and inferred tin deposits.

Jan 1, 1949

By S. S. Clarke

This paper on methods and costs of mining at the Westside mine, in the Tri-State zinc-and lead-mining district (Missouri-Kansas-Oklahoma), is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in various mining districts of the United States. Methods and equipment used in drilling, loading, and underground transportation have changed radically since the latest Bureau of Mines publications2/ on mining methods in the district were published more than 20 years ago. More efficient methods and machines have been developed in order to maintain low operating costs in the face of rising labor and supply costs and lower grade ore. The rate of conversion to mine mechanization was disappointing at times; local conditions required the development of special equipment, and available rock-moving machines had to be remodeled and strengthened.

Jan 1, 1957

By Heinz W. Sternberg

The literature on electrochemical treatment of coal is reviewed, and possible avenues of further research in this field are discussed in this report. Electrolytic reduction of finely distributed coal resulted in the addition of as many as 9 atoms of hydrogen to 100 atoms of carbon. Reduction of coal extracts at controlled potentials indicated the presence of condensed aromatic hydrocarbons and reducible quinones in coal. As much as 65 percent of low-rank coal can be made alkali soluble by electrochemical treatment. Higher rank coals gave smaller yields of alkali-soluble products. However, the nature of this reaction is not clear. The difficulty of reducing coal electrolytically is probably due to the insolubility of coal and not to any structural peculiarity. Reduction of coal by electrolytically generated radical anions appears to be a promising approach for further research.

Jan 1, 1962

By George T. Faust, S. R. B. Cooke

"The Southern Experiment Station of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, is investigating the preparation of pulverized coal for fuel. In this study the relative amount of surface in various products and samples had to be assessed. Because of the familiarity with screens and because of the simplicity of using the inverse ratio of the opening for ascertaining the amount of relative surface in the respective sizes, screens down to and including 270-mesh were used. This choice was made in full cognizance of the irregularity of screens, but it seemed that if the same screens were used throughout all the tests the relative values would be satisfactory.In dealing with the subsieve sizes, pneumatic elutriation was used to make several fractions to extend the sizing analysis into the range of hypothetical screens. This kind of a sizing analysis was thought necessary because it is familiar to all operators, and, furthermore, it is amenable to several ways of plotting curves that bring out the characteristics of various coals and various methods of grinding.The method of obtaining the data from which to set up the hypothetical screen scale is the subject of this paper. It consists in determining the average projected area of the particles in the respective elutriated products. By extending the ""area method"" to sieve sizes, a factor is found that may be applied to the subsieve sizes, and thus the scale is projected in a regular manner. This method avoids contentions about specific surface and steers clear of ""average diameter"" except as material sized on screens may be said to have an average diameter."

Aug 1, 1939

By Ralph B. Youtz

This paper describing mining methods at, the Eighty-Five mine of the Calumet and Arizona Mining Co., Valedon, N. Mex., is one of a series being prepared by the United States Bureau of Mines on mining methods, practices, and costs in the various mining districts in the United States. The Eighty-Five mine is in southwestern New Mexico, 3 miles southwest of Lordsburg, Hidalgo County (see fig. 1). The mine produces normally 7,000 to 8,000 tons per. month of silicious copper-gold-silver ore, and employs approximately 200 men underground and 40 on-the surface. Mining is done by shrinkage and cut-and-fill methods.

Jan 1, 1931

By G. W. Birge, D. E. Wolfson, J. H. Lynch

Fourteen coal samples representing the Flag , Fire Clay , Whitesburg , Amburgy , Upper Elkhorn No. 3 , Upper Elkhorn No. 2 , Upper Elkhorn No. 1 , and Lower Elkhorn beds in Letcher County , Ky . , were carbonized by the Bureau of Mines - American Gas Association ( BM- AGA ) method , and yields of products and physical properties of cokes were determined . The samples tested were high- volatile A bituminous in rank , with dry , mineral - matter- free fixed - carbon contents ranging from 55.3 to 62.2 percent . Five of the samples , as received , were chemically unsuitable for metallurgical use because of excessive ash and/ or sulfur content . Generally , strength indexes of the cokes were low and all of the coals would require blending with higher rank coal to obtain satisfactory blast furnace fuel .

Jan 1, 1964

By V. E. Edlund

This report presents the results obtained in a study of the technical feasibility of recovering a usable pig iron by pyrometallurgical treatment of typical copper reverberatory slags . The iron in the slag was readily reduced with carbon , but the copper and sulfur content of the metal was best controlled by a three - stage procedure comprising ( 1 ) melting the slag with pyrite to remove copper as a low- grade matte , ( 2 ) smelting the partly decopperized slag with fluxes and carbon to reduce the iron , and ( 3 ) refining the impure iron alloy from step 2 with a flush slag to remove sulfur and residual copper . Laboratory - scale tests demonstrated that washing with 8 wt pct of pyrite lowered the copper content of a typical reverberatory slag from 0.58 to 0.12 Subsequent smelting of a mixture composed of 70 pct decopperized slag , 25 pct lime , and 5 pct coke reduced 84 pct of the iron to metal containing 2.27 pct sulfur . This metal then was successfully desulfurized by treatment with a basic flush slag to produce a finished metal that contained , in percent , 93.5 Fe , 0.02 S , 0.26 Cu , and 4.9 C. Overall recovery of iron under the conditions of trial was about 80 pct . This could be increased if higher tolerances for copper could be accepted . Commercial processing would be accomplished in three furnaces with molten materials passing from one to another . Currently produced smelter slag could be treated fairly inexpensively , because the molten product would require only a little additional heat to produce an iron byproduct that undoubtedly would be attractive to local foundries .

Jan 1, 1964

The Bureau of Mines conducted a field study to assess the performance of various chain pillar configurations in terms of gate road entry sta-bility. Vibrating wire stressmeters (VWS's) were installed in four consecutive gate road chain pillars. Field data collected during panel retreat were analyzed to gain a better understanding of the mechanics of vertical load redistribution in gate road chain pillars as it relates to ground control problems. Several different pillar configurations were investigated including abutment-yield and yield-abutment-yield designs. VWS data indicate that average pillar loads were lower and appeared abutment-yield pillar arrangement was utilized. port the occurrence of severe roof and pillar to stabilize when an Data analyses also supdeterioration that was visually observed in the tailgate entries during panel extraction.

Jan 1, 1988

By A. B. Needham

A number of the pegmatites in the southern Black Hills of western South Dakota contain sheet mica; and as the demand increased during World War II the area became an important producer of strategic qualities of mica. During this period of maximum activity, the U. S.. Geological Survey made detailed studies of the geological structural control, the mineralogical associations, and the production Of many pegmatites in the Black Hills. On the basis of results of this study, and at the suggestion of the Geological Survey, several of the pegmatites were examined by the Bureau of Mines, and a few were selected for further investigation. Accordingly, the White Bear, Silver Dollar, Buster Dike, and Hot Shot mines were diamond-core-drilled in 1947. The Hot Shot mine was investigated further by deepening the shaft and crosscutting the pegmatite in 1948. The mica-bearing deposits occur in lenticular intrusions of pegmatite in schists of various mineral composition. Eleven diamond-drill holes, totaling 2,111.4 feet in length, were completed on the four deposits. The shaft on the Hot Shot deposit was deepened 44 feet to the 112-foot level, and crosscuts were driven from the bottom of the shaft to the hanging Wall and foot wall of the pegmatite. This publication briefly describes the location, ownership, and history of the deposits and gives details of the work done by the Bureau of Mines and the Geological Survey.

Jan 1, 1950

By C. C. Hustwit

The U.S. Bureau of Mines formulated a new mathematical model to characterize iron oxidation. The new model is intended to replace the currently used model, recommended by the Environmental Protection Agency (EPA), for most acid mine drainage (AMD) treatment applications. The new model was evaluated in a series of five synthetic AMD treatment tests. The initial ferrous iron concentrations ranged from 800 to 2,400 mg/L. In these tests, the Bureau model underpredicted the measured ferrous iron oxidation rates by a range of 3.24 to 8.03 pct. This was considered to be in close agreement after consideration of experimental error. The model proposed by the EPA was also evaluated using the same test data. The EPA model underpredicted the oxidation rates by a range of 77 to 100 pct in four tests and overpredicted by 19 pct in one test. The model formulated by the Bureau expresses that the rate of iron oxidation is a function of a treatment system's oxygen transfer efficiency and is independent of ferrous iron concentration when treated to near-neutral pH's. A new test method for evaluating oxygen transfer in flow-through reactors is also described.

Jan 1, 2010

By R. M. Santmyers

Umber and sienna, like ocher, are naturally occurring mineral pig- ments composed largely of clay permeated with hydrated iron (ferric oxide), but they differ from ocher in that they also contain hydrated manganese oxide. The presence of manganese accounts for their browner color. In addition to silica and alumina (clay) and the coloring oxides of iron and manganese, these pigments often contain lime, barium, and other metallic salts as impurities. Sienna most nearly approaches ocher in chemical composition, and the chief distinction is its physical character. It grades into ocher with de- creasing iron content and into umber with increasing manganese content. Sienna is translucent rather than opaque and is more of a stain than a pigment; as the iron oxide content is rather high (often 60 to 80 per cent), the color is strong and rich and varies from pure brown to reddish brown. This pigment raw sienna, terra di Siena, and Italian earth. is known under several names: Burnt sienna is a pigment of an orange-brown tint made by cautionsly calcining raw sienna. It is divided into two grades; American, and Italian burnt sienna. American burnt sienna is a reddish-brown pigment containing from 25 to 60 per cent iron oxide (Fe2O3). One grade, found in Pennsylvania, analyses as high as 80 per cent and is mown as double strength sienna. Italian burnt sienna is a pigment generally containing more iron than the American product, averaging 60 to 75 per cent iron oxide.3 American pig- ments of the same iron content differ materially in shade, having a Havana- brown color, whereas the Italian is more of a maroon. Italian siennas when tinted with 20 per cent of white, show a bluish tint, whereas American siennas yield a brownish or yellowish hue. Raw umber, also known as Turkey umber, Levant umber, and terra ombra, is a greenish to yellowish brown siliceous and ferruginous earth, containing a considerable proportion of one or other of the higher oxides of manganese, Mng04 and MnO2." It is similar in many respects to raw sienna except that it is much coarser and contains more manganese oxide. All umbers contain over 5 per cent of manganese dioxide. Like sienna, umber is a permanent pigment, not being injured by light or by impure atmospheres. Burnt umber (velvet brown, chestnut brown, etc.), results from the calcination of raw umber. The color is much richer and warmer than that of the raw umber. The colors are equally permanent and can be used in conjunc- tion with all other durable pigments.

Sep 1, 1931

By W. W. Adams

"The main purpose in the compilation of accident statistics is to reveal conditions that may result in injury to persons or property so that remedial measures may be applied. For practical reasons it is usually found necessary to restrict inquiry to conditions which actually have caused personal injury, and to omit those which nay, but have not yet, resulted in damage, Fortunately or unfortunately, there is a sufficient number of the former to indicate the existence of hazards so numerous as to require all of the attention which the industry can devote to the subject.Two years ago, the Bureau of 'mines, in cooperation with the National Safety Council, undertook an intensive campaign to obtain more complete and satisfactory information regarding mine accidents than had theretofore been available. Since 1911 the bureau had been receiving annual summaries from all companies operating metal mines, showing, in a general way, the number and causes of accidents that occurred during the preceding year and the number of men employed at the mines. Monthly summaries of fatal accidents at coal mines were received from the state inspectors, showing the number of deaths attributed to each of 22 main causes of accidents, Information for individual coal mines was not furnished.While this information, nation-wide in scope, is indispensable because it epitomizes the progress or retrogression in the industry as a whole, and serves as a background of specialized studies, yet certain classes of acci¬dents, for example, those that are more or less peculiar to specific districts or mines, require an analysis in greater detail than is possible on the sole basis afforded by the annual summaries.The need for more specific information was realized some years ago in the State of Pennsylvania in connection with the administration of the workmen's compensation law, The mining industry is well acquainted with the val¬uable studies of accidents, particularly nonfatal accidents, in the mines of that State being conducted by Mr. Rush N. Hosier."

Sep 1, 1924

By M. Carrales

This Bureau of Mines report presents information on the sulfur content of crude oil in the United States and in some foreign countries. Data are presented for oil produced in 1971 from fields in 26 States that accounted for about 76 percent of total U.S. oil production; the foreign data cover fields in 24 foreign countries that accounted for about 64 percent of the total oil produced from these countries in 1971. Most of the data are presented in tabular form.

Jan 1, 1975

By Howard B. Hamilton

A switching system for high fault current 300 and 600 volt DC trolley and haulage systems, as used in the mining industry is presented. The system consists of paralleled main and auxiliary contactor circuits with a liquid metal current limiting device (CLD) in series with the auxiliary contact-or. Upon detection of a fault, the current is commutated into the CLD circuit. The liquid-metal vaporizes, increasing the CLD resistance and Considerably decreasing the actual current to be interrupted. This system will materially reduce the wear and tear on contactors because of the reduced interrupting requirement. the CLD is pressurized; when the current is interrupted, liquid metal flows back into the bore. Thus, it is resetting. Electrical and mechanical design principles are presented as well as materials for use, as found satisfactory in field tests on the device.

Jan 1, 1982

By William T. Reid

Low-temperature carbonization of coal in Japan served as an important source of liquid fuels during the war. Six plants operating in Japan Proper produced 203,069 KL (53.7 million gallons) of liquid fuel from 1940 until the end of the war in August 1945, while four additional plants in Karafuto and Korea produced 211,943 KL (56.0 million gallons) for a total of 415,012 KL (109.7 million gallons) of liquid products. Semicoke produced in these plants was used for domestic fuel, for gasi- fication in portable gas producers on automotive vehicles, and to replace imported low-volatile bituminous coal in the manufacture of metallurgical coke. Since 1936 one plant had produced more than 300,000 metric tons of semicoke for blending with bituminous coal to form coke, while the total production of semicoke since the beginning of the industry in 1923 is approxi- mately 2,000,000 metric tons. Despite an apparent annual carbonizing capacity of about 2,000,000 metric tons of coal for the entire country, the maximum amount of scmicoke produced during the peak year, 1943, was 468,446 metric tons. The equipment used is primarily of Gorman design. Just before the end of the war, 6 plants using 20 Lurgi carbonizers were operating with a total rated capacity of more than 1,500,000 metric tons of coal per year, while 2 Koppors units had a combined annual rated capacity of 400,000 metric tons of coal. One plant using the Japanese-designed Mimura system was in service but with so much mechanical trouble that its output was small, while in another plant 4 Wanisht carbonizers of Japanese design but based on an early German development were running satisfactorily, and carbonizing about 100,000 metric tons of coal per year. A single installation of 15 American-designed Knowles ovens was operating near Tokyo but was carbonizing pitch for electrode carbon. ..! No true low-temperature process used in Japan could carbonize strongly. caking coals satisfactorily. The Mimura process designed for this purpose was unsuccessful, as was the Shimomura process before it, while the Lurgi, Koppers, and Wanishi systems operated only with noncaking or very weakly caking coals. The Knowles ovens, really a medium-temperature process, could carbonize-caking coal without difficulty...

Feb 1, 1948