Search Documents

By J. B. Umhau

During 1928 the United States consumed 73,270 long tons of virgin or primary tin, which was approximately 7.5 per cent more than the 68,198 long tons con¬sumed in 1927 and equaled 41 per cent of the world's production in 1928 (approximately 178,000 long tons). Consumers' stocks amounted to 9,268 tons on January 1, 1928, and 8,587 long tons on December 31, 1928, a net reduction of 681 tons. In addition to the virgin tin accounted for above, 12,106 long tons of secondary metallic tin were used by manufacturers of tin products in 1928. These figures are the result of an inquiry addressed by the Bureau of Mines to manufacturers to determine the amount of metallic tin used by them; in reply, 1,307 establishments reported consumption in 1928. The distribution of the amount consumed by various uses, as shown in the allowing tabulation based on Bureau of Mines canvasses for 1927 and 1928 in comparison with consumption by uses reported by the War Industries Board for 1917, emphasizes the fact that new uses for tin have been developed in only minor or insignificant amounts. Furthermore, although the studies for recent years show that some older uses have been discontinued, the amounts involved were all small and insignificant. Variation in consumption from year to year parallels the fluctuations in demand for the already well-established tin products. For example, the manufacture of bearing metals and solders for motor cars and trucks required 19,000 tons in 1928 compared to 16,000 tons in 1927; the canning industry continues to require the greater portion of the tin plate and also much solder. Growth in the electrical and the more recently developed industries (aeroplane, refrigerators, radio, etc.), while affecting total consumption of bearing metals, solders, etc., has made little change in the proportions required for these basic methods of using tin.

Jan 1, 1929

By Hugo E. Camargo

In an effort to reduce Noise Induced Hearing Loss (NIHL) in the mining industry, the National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop noise controls for mining equipment whose operators exceed the Permissible Exposure Level (PEL). The process involves three steps: 1) Noise source identification (NSI), 2) development of noise controls, and 3) evaluation of the developed noise controls. For the first and third steps, microphone phased array measurements are typically conducted and data are processed using the conventional beamforming (CB) algorithm. However, due to the size and complexity of the machines, this task is not straight forward. Furthermore, because of the low frequency range of interest, i.e., 200 Hz to 1000 Hz, results obtained using CB may show poor resolution issues which result in inaccuracy in the noise source location. To overcome this resolution issue, two alternative approaches are explored in this paper, namely the CLEAN-SC algorithm and a variarion of an adaptive beamforming algorithm known as Robust Capon Beamformer (RCB). These algorithms were used along with the CB algorithm to process data collected from a horizontal Vibrating Screen (VS) machine used in coal preparation plants. Results with the array in the overhead position showed that despite the use of a large array, i.e., 3.5-meter diameter, the acoustic maps obtained using CB showed "hot spots" that covered various components, i.e., the screen deck, the side walls, the I-beam, the eccentric mechanisms, and the electric motor. Thus, it was not possible to identify which component was the dominant contributor to the sound radiated by the machine. The acoustic maps obtained using the RCB algorithm showed smaller "hot" spots that in general covered only one or two components. Nevertheless, the most dramatic reduction in "hot" spot size was obtained using the CLEAN-SC algorithm. This algorithm yielded acoustic maps with small and well localized "hot" spots that pinpointed dominant noise sources. However, because the CLEAN-SC algorithm yields small and localized "hot" spots, extra care needs to be used when aligning the acoustic maps with the actual pictures of the machine. In conclusion, use of the RCB and the CLEAN-SC algorithms in the low frequency range of interest helped pinpoint dominant noise sources which otherwise would be very hard to identify.

Jan 1, 2009

By R. Blickensderfer

Laboratory wear testing was conducted by the Bureau of Mines on a variety of typical wear-resistant alloys used in mining and mineral-processing equipment to establish their relative spalling and abrasion resistance. Test specimens in the form of 75-mm-diam balls were subjected to repeated impacts until they broke, spalled excessively, or received several hundred thousand impacts. Pin specimens removed from the balls were evaluated for high-load abrasive wear. The alloys in-cluded commercial forged steels, cast steels, manganese steels, and four types of white cast iron, with a range of heat treatments. The effects of hardness and microstructure on impact wear and abrasive wear are discussed. The data should help mine operators select the compositions and heat treatments that best suit service conditions.

Jan 1, 1985

Study to develop a new and more cost effective equipment system, incorporating a winch-pulled dozer blade, for leveling spoil and performing reclamation of area strip mines.

Jan 1, 1975

By Carl R. Christiansen

The primary objectives of this project are (1) the determination of manpower demand in primary lead and zinc production for the years 1985 and 2000, and (2) the estimation of the availability of the required manpower for these years. In order to meet the first of these objectives relationships between employee requirements and metal production in the various states were established, The total primary lead and zinc production from United states mines in 1985 and 2000 has been predicted by the U.S. Bureau of Mines. These forecasts and the 1974 figures are as follows: [1974 1985 2000 Lead metal, tons 669,000 700,000 900,000 Zinc metal, tons 494,000 585,000 995,000] Mining By analysis of ore reserve data and industry characteristics, the authors estimated the portion of the primary production which each state would yield in the future years. As manpower requirements are determined by the tons of ore produced and by worker productivity, these figures were determined for each mining state and district by developing relationships between lead and zinc metal production, ore production, ore to recoverable metal ratios, employee productivity, and number of employees required. The number of new employees required annually to compensate for attrition and production growth is provided, also.

Jan 1, 1975

By W. P. Haynes, A. J. Youngblood, J. J. Demeter

Synthesis of high - Btu gas , using the Fischer - Tropsch reaction was investigated in a tube - wall reactor of 2 - inch steel . The catalyst was carbonexpanded iron ( CEI ) , formed on the walls of a steel reactor by exposing the reactor to 1H₂ + 100 synthesis gas under certain conditions . Advantages to be gained from successful development of the CEI - coated tube- wall reactor are elimination of catalyst plant and catalyst handling and charging operations , high- temperature operation , and a relatively low- cost , reactor -heat recovery system . In one test ( TW- 8 ) in which the reactor was filled with CEI , the reactor was operated for 1,910 hours before the test was stopped because of excessive pressure drop caused by carbon deposition . The pressure drop was satisfactory for 1,000 hours of operation at an hourly space velocity of 300 , but it increased rapidly at space velocities of 600 and 1,000 . When operated at a space velocity of 300 , with a ratio of 1 to 1 recycle at 534 ° C , a conversion of 72 percent of the 3H + 100 synthesis gas was achieved . The product gas had a heating value of about 610 Btu per cubic foot and could be suitably upgraded to 900 - Btu gas by subsequent use of a nickel catalyst . CEI did not operate effectively as a film catalyst under conditions of generation tried in this study . Generally , operation of the 2 - inch reactor with CEI catalyst was unsatisfactory because of poor reproducibility of the activation step and poor temperature control resulting in high- operating temperatures and eventual plugging of the reactor . Tests using CEI in fixed , packed beds suggest that the most likely application for CEI in producing high - Btu gas would be a moving - bed reactor , where sufficient bed movement and heat removal are provided to prevent plugging .

Jan 1, 1964

By Robert H. Ridgway

This circular outlines salient facts regarding the manganese-ore industry in the United States and the world. It is founded chiefly upon published information available in the literature of the subject. The Bureau of Mines has in its files additional, more detailed data upon many of the topics presented very briefly here, and will endeavor to assist the mineral industries and public by giving further information in response to individual inquiries. The Bureau will welcome comments, criticisms, and contributions of data that may assist in making later additions of this circular more accurate, or in developing more fully its mineral files pertaining to manganese. In reporting the production of manganese-bearing ores in the United States the following classification has been adopted by the Bureau of Mines: (1) Metallurgical-grade ores, under which have been classified manganese ores containing 35 percent or more of manganese used in the manufacture of iron and steel, ferruginous manganese ore containing 10 to 35 percent of manganese, manganiferous iron ore containing 5 to 10 percent of manganese, and manganiferous zinc residuum; (2) battery ore; (3) fluxing ores, under which are classified ores that may contain a few ounces of silver and are rich enough in manganese to make them valuable chiefly for fluxing purposes in nonferrous smelters; and (4) miscellaneous ores, under which are classified the ores shipped to brick manufacturers, glass makers, and manufacturers of manganese chemicals.

Jan 1, 1933

By David J. Kusler

A gravimetric method for the determination of carbon dioxide, carbon monoxide, hydrogen, methane, and oxygen in blast furnace top gas is described. Nitrogen may be determined directly by volume measurement or by difference. The method is direct, permits continuous as sampling, and provides an averaged analysis over a selected range of sampling intervals from 1/2 to 24 hr or more. Neither expensive equipment nor specialized personnel are required. The method is suitable for routine analysis, and the results compare favorably with those obtained by established methods.

Jan 1, 1963

By G. S. Scott

The Bureau of Mines is engaged in research to assess the hazards associated with the handling, storage, and use of combustible gases, vapors, and. liquids encountered in mines and in industry. As a part of this general pro-gram, numerous limits of flammability and ignition temperatures are being investigated for a wide variety of combustible materials, and methods are being developed to minimize the explosion hazards of these combustibles. The Bureau receives numerous requests for information on the explosion hazards of specified combustible mixtures under various conditions of use. This information circular has been prepared to assist those who may have similar requests. Destined primarily for the layman with a limited technical knowledge of the subject, it considers rather briefly the numerous factors that enter into the general problem of gaseous explosions and their prevention.

Jan 1, 1951

By W. H. Strickland

Ultrasonic ranging sensors are inexpensive, have no moving parts, have no lenses to clean, are normally small and unobtrusive, and can measure distances through moderate amounts of dust, smoke, and humidity, so they are well suited to underground mines. In the work reported here, conducted by the U.S. Bureau of Mines, researchers tested ultrasonic ranging sensors for their ability to define rib line features for computer-aided navigation of underground mine mobile equipment. The investigation began with laboratory tests of field of view, angle of incidence, intersensor variation, and ranging accuracy of the individual rangers in a ring array produced by Denning Robotics of Wilmington, MA, The results showed that the sensors have good accuracy and low variability. Additional experiments at AMAX'S Henderson Mine showed the sensors could accurately and reliably measure the distance to mine features, including convex and concave corners and rib intersections. The results showed that when used properly, the ranger data are accurate enough for reliable mine vehicle navigation. When used incorrectly, ultrasonic rangers do not provide the anticipated data. Therefore, this report explains the principles of ultrasonic range measurement, describes the ranger's strengths and weaknesses, and explains proper ranger use and data analysis.

Jan 1, 2010

By Alan R. Buehler

The Bureau of Mines conducted a mineral investigation of the 10,500-hectare Cache Peak study area in 1992; the area had been proposed as wilderness. Bureau personnel examined and sampled prospect workings; 14 rock and 20 placer samples were taken during the investigation. The study area is centered about 40 km south-southeast of Burley. Idaho, in the Sawtooth National Forest. There were seven mining claims located inside the study area, and one additional historical mining claim location. Gold, silver, copper, lead, zinc: Possible resource, poor exposure precludes estimate. Marble: Several million tonnes may be suitable for a variety of uses; markets too distant to favor mining. Sand and Gravel: Several million m3, but markets and transportation costs do not favor mining. Quartzite: Several million tonnes may be suitable for metallurgical purposes; however, markets are too limited to mine. Slabs have been quarried at three localities adjacent to the study area, for decorative stone. Production: In 1979, two tonnes of ore were produced and a plan of operations was submitted calling for approximately 5 km of access road for the Last Chance mine. Decorative stone production was not recorded.

Jan 1, 1993

By T. F. Mitchell, B. K. Shibler, J. V. Batty, W. G. Sandell, G. M. Potter

"INTRODUCTION The Park City district, situated 30 miles east of Salt Lake City, Utah, in the Wasatch Mountains, Is a well-known producer of lead, zinc, and precious metals. Nearly continuous production has been maintained from the dis¬trict since its early discovery about 1870. For approximately 50 years, gravity milling methods were employed to beneficiate Park City ore, and during that time tailings from the mills were sluiced down Silver Creek and deposited on lands below the camp for 7 miles.Owing to the large tonnage of tailings deposited along Silver Creek, considerable work was done in the past in the attempt to develop a low-cost concentration method for re-treating this material, but no-method was found that was economically feasible. The Bureau of Mines was asked to conduct beneficiation tests on Park City tailings in November 1944, and metallurgical studies were initiated at that time. This report summarizes the results of laboratory ore-dressing studies made on samples from the Grasselli deposit."

Dec 1, 1947

By W. R. Hardwick

Nuclear explosive fracturing has been suggested as a method to make hard rock amenable to extraction by a modified block-caving method. To evaluate this possibility, conventional and nuclear blasting practices are discussed, underground mining methods for large deposits and their costs are described, and the cost of fracturing ore with a nuclear explosive and subsequent mining by a modified caving system is estimated and compared with both open-stope and block-caving mining costs. While the direct cost of fracturing the ore in hard rock with a nuclear explosive is less than with conventional explosives, additional costs imposed by the use of nuclear explosives may make their use unattractive for deep mining.

Jan 1, 1970

By John A. Organiscak

[Fugitive Just is generated alone unpaved mire reads from intermittent equipment traffic. Typically, the majority of such traffic consists of trucks hauling either mine product or waste [rum the surface mime pit and/or the processing plant. Fugitive dust generated along these unpaved mine roads includes particles of all sizes which become airborne. The potential hazards include the deleterious effects to human health of inhaled dust, traffic visibility hazards and environmental impacts on the localized area by the larger-sized visible airborne dust. Two held surveys were recently conducted to quantify fugitive dust generation and dispersion from truck traffic on unpaved and untreated mine haulage roads For these surveys., airborne glow sampling was conducted at multiple sampling fixations away from an unpaved haulage road at a limestone quarry/plant and at a coal mine preparation plant lo measure the size characteristics, concentrations. and dispersive behavior of the dust cloud generated from truck traffic- Results show that at least 80% of the airborne Just generated by haul trucks was larger than 10 µm- Airborne respirable, thoracic, and total dust concentrations all decreased and approached background concentrations 30.5 in (100 feet) from the road This report describes the average and instantaneous peak dust levels that were measured tip to 30.5m (100 feet) Iron the haulage road. Keywords: Unpaved mine road, fugitive dust, silica.]

Jan 1, 2008

By Robert B. Hoekzema

The Bureau of Mines and U.S. Geological Survey completed a 4-yr (1979-82) mineral appraisal of the Chugach National Forest (CNF), AK. This report summarizes the Bureau's placer gold studies in the CNF. Placer mining from the mid-1890's through 1982 produced an estimated 133,800 oz of gold, of which two-thirds was produced prior to 1920. As much as 6,800 oz of placer gold was produced from 1979 to 1982. Most production came from Crow, Canyon, and Resurrection Creeks. Five types of placer gold deposits were identified in the CNF: (1) alluvial placers, (2) bench placers, (3) eluvial placers, (4) glacial placers, and (5) marine placers. Placer sampling indicated a potential for gold production from alluvial and bench placers associated with historically mined drainages such as Crow, Canyon, Resurrection, Sixmile, and Mills Creeks and from unmined drainages including the Avery, Kings, Snow, Copper, and Tasnuna Rivers and several smaller streams throughout the CNF. Results of fineness tests indicated that gold from the CNF ranges from 455 to over 950 fine. Subsequent investigations in drainages with anomalous placer sample values also identified previously unknown lode mineralization.

Jan 1, 1986

By L. A. Readdy

Pilot Hole "X" was drilled to test the formations through which the ventilation shaft for the proposed U.S.B.M. demonstration oil shale mine would be drilled. The geologic formations encountered in this hole are discussed. Correlation of the geologic horizons encountered in this hole with those encountered in nearby drill holes was accomplished by the use of geophysical logs. Data on the geophysical interpretations are provided. The anticipated geotechnical characteristics of the geologic units encountered in Pilot Hole "X" are described.

Jan 1, 1977

By Michael P. Moore, Christopher J. Rise

"Over the past twenty years, there have been numerous studies which have attempted to correlate the prevalence of Coal Workers' Pneumoconiosis (CWP) with different characteristics of the coal seam. Some investigators have tried to find a relationship, or the lack of a relationship, between the rank of coal seams and the incidence of CWP. Others have attempted to show that there is a positive correlation between the mean mass of respirable dust in the mine atmosphere and the prevalence of CWP. Still others have tried to determine the influence of the quartz content of respirable dust on the incidence of CWP. Unfortunately, many of these different investigations have conflicting conclusions.One area of research with conflicting conclusions deals with the relationship between the rank of the coal and the incidence of CWP. For example, an inves¬tigation conducted in Pennsylvania and West Virginia coal mines concluded that the prevalence of CWP increases with an increase in coal rank (1). A study in Great Britain also observed a close relationship between the rank of coal and the prevalence of CWP (2). However, another study involving 312 Appalachian coal miners concluded that the association between coal rank and CWP might be fortuitous and that other factors may be more important (3). In addition, an investigation involving 2,600 miners during a period of twenty years in Great Britain established that there is only a weak correlation between the prevalence of CWP and the rank of the coal (4). Consequently, it appears that there is still uncertainty as to whether or not the rank of the coal seam has an influence on the development of CWP.Another area of investigation concerns the relationship between the mean mass of respirable dust present in the mine atmosphere and the prevalence of CWP. A study involving 4,122 miners over a period of ten years in Great Britain noted a high correlation between the mean mass of respirable dust and the incidence of CWP (5). Another investigation involving 3,154 British face workers con¬cluded that the overall mass of respirable dust is the factor most closely related to the ten-year attack rate of CWP (6). However, a study conducted in thirty-one mines in the United States concluded that it is doubtful that the quantity of respirable dust alone is responsible for the difference in the prevalence of CWP (7). Even though there are conflicting conclusions, there are many more investigators who confirm, rather than deny, the relationship between the mean mass of respirable dust and the development of CWP.The third subject of investigation is the role of quartz in the incidence of CWP. For example, two studies in Great Britain concluded that the quartz content in coal mine dust has no relationship to the prevalence of CWP (8,9). But a study involving 312 Appalachian coal miners revealed that the level of exposure to free silica plays an important role in the development of CWP (10). Once again, the conclusions reached by different researchers are conflicting.Probably the most important factor in the discrepancy among the studies is the variability among different coal mines. A mine operating in an inherently ""dusty"" seam may have a low concentration of respirable dust while a mine operating in a less dusty seam may have a high concentration of respirable dust. This discrepancy is a result of variables such as the effectiveness of ventilation or the efficiency of the water sprays. Consequently, it is very difficult to compare the dustiness of different coal seams by in-mine measurements of the respirable dust concentration. A laboratory test would more accurately characterize a coal seam according to its respirable dust production."

Jan 1, 1988

By Walter E. Lewis

The Cuyuna iron range in Crow Wing County, Minn., is the principal producer of manganiferous iron ore in the United States. The ore is mined from a manganiferous iron formation in the bedrock of the Cuyuna district. This iron formation is divided into two general lithologic types-thin-bedded and thick-bedded. The unoxidized, thin-bedded iron formation is composed of iron silicate with associated fine-grained carbonates of iron and manganese. The thick-bedded iron formation carries iron and manganese oxides with intimately associated silica. Oxidation and leaching of the original iron formation have been the most influential factors in producing manganiferous iron-ore concentrations in quantities large enough to exploit on a commercial basis. The unoxidized and the partly oxidized and enriched iron-formation materials are suitable as a source of ferrograde manganese ore. These materials have been classified according to their amenability to mineral dressing and degree of oxidation and leaching.

Jan 1, 1958

By Jack Smith

New turbine blades designed to resist ash erosion were tested by the Bureau of Mines in a pilot-scale coal-fired gas turbine. After a total of 1,963 hours, the rotor blades were only slightly eroded; and they had an estimated useful life of 20,000 to 30,000 hours. Changes in aerodynamic design of the blades successfully concentrated the ash at the outer casing, but stepped sidewalls for the rotor drum and wear strips at the bases of the rotor blades are still needed to minimize wear at these points. Stepped sidewalls and wear strips did not adequately protect the stator blades. Ash slightly eroded their leading edges, above the inserts, and cut notches into their trailing edges near the bases. Stator blade life was estimated at 5,000 to 7,500 hours. Blade erosion in these tests was less severe than with previous designs, but more efficient combustors and ash separators are required to reduce the amount and size of ash entering the turbine, to achieve acceptable blade life for commercial operation.

Jan 1, 1967

By D. J. Bauer

A solvent-extraction system employing selective stripping of a pre loaded organic phase was investigated for recovering Sm203 from a light-group rare-earth mixture. The samarium concentrated in the organic phase, and a >99-pct-pure samarium oxide product was obtained at 76-pct recovery in a 20-stage operation using di(2-ethylhexyl) phosphoric acid (EHPA) as the organic phase. The stripping agent was a 1.5-pct hydrochloric acid solution containing 200 g NH4C1/1.

Jan 1, 1972