Search Documents

By John J. Mulligan

Coalbeds were discovered in outcroppings of the Beacon group of sediments on the north end of the Willett Range ( altitude 77 ° 11 ' S , longitude 160 ° 20 ' E ) , Victoria Land , Antarctica , in December 1960 during an investigation undertaken as part of the U.S. Antarctic Research Program under the auspices of the National Science Foundation . Three separate exposures of coal or coaly material were found . Two of the exposures contain , respectively , eight and four beds of hard , compact , finely banded attrital coal ranging in thickness from 8 feet downward to a few inches , and reported to range in rank from mediumvolatile bituminous to semianthracite . The coals are associated with carbonaceous shales containing an abundant assemblage of fossil plants resembling those associated with the Permian coals of Australia and other Gondwana areas . The third exposure , apparently somewhat higher in the stratigraphic sequence , contains only coaly plant fragments scattered through a thin conglomerate and overlying sandstones . A sandstone bed that overlies these coal - bearing sandstones contains abundant logs and fragments of silicified wood . Preservation of features is poor , but one segment of a silicified stem suggests comparison with Rhexoxylon , a gymnospermous tree that usually is considered indicative of Triassic age . The Beacon sediments in this area have been invaded , broken , and uplifted by a massive series of diabase sills and dikes greater in volume than the intruded sediments . The heat emitted by these intrusives must have advanced the metamorphic development of the coals . However , there is no evidence of alteration to graphite , and coal found in direct contact with a diabase sill contains no vesicles or other usual evidences of natural coking . Either the pressure of overlying rocks inhibited the development of coke , or the coals had been metamorphosed beyond the coke forming stage before the igneous intrusion .

Jan 1, 1963

By R. L. Crosby

The effect of indium on the solid solubility of calcium and of silicon in magnesium was studied using metallographic, X-ray diffraction, and electrical resistivity techniques. The addition of 2 weight-percent or more of indium reduced the solid solubility of calcium in magnesium by forming a compound containing indium and calcium. Indium additions have no perceptible effect on the solid solubility of silicon in magnesium.

Jan 1, 1963

By Stephen C. Tadolini

The U.S. Bureau of Mines has developed ultrasonic measurement instrumentation capable of measuring strains and elongations on tensioned and untensioned mine roof bolting systems. This report evaluates the pulsed-phase-lock-loop and pulse-echo systems. The pulse-echo systems measure time of flight of a signal through the bolt. The ultrasonic instrument converts the measurement into elongations or stress. The most recent Bureau instrument development converts travel-time measurements directly into elongation, load, stress, and torque by simple data manipulation from the keyboard. Bolt preparation and instrument calibration are described in detail.

Jan 1, 1990

By W. J. Kroll

The production of beryllium metal and its alloys is one of the most difficult tasks in metallurgy. In this report we shall examine the progress made in this work- in the last 15 years; taking into account the outstanding publications, including; those of the patent literature, and the information obtained during our 20 years? experience with this metal. The difficulties experienced' in producing elementary beryllium derive from the physical nature as well as from the chemical behavior of the metal and its compounds. Its oxygen affinity is about the same as that of calcium and a little higher than that of magnesium. Its chlorine affinity is much lower than that of magnesium, about equal that, of manganese, and little higher than that of aluminum. The sulfur and nitrogen affinity is probably almost the same as that of calcium for these elements, and beryllium carbide is probably more stable than aluminum carbide, A14C3. The intermetallic affinity of beryllium may be given in descending order, as follows: Nickel - copper - iron. It forms eutectics with -aluminum and silicon as well as with silver. It does not alloy with magnesium and only partly with calcium. Its oxide melts at 2,570° C., but CaO and BaO form readily fusible eutectics with BeO(65).3/ No igneous solvents are known for BeO, which behaves id this regard like Mgo. The beryllium silicate is a strong compound, the aluminete much less so; however, CaO easily displaces Be in the heated mixtures. The Anhydrous chloride hydrolyzes, and it cannot be made from aqueous liquors. It sublimes at 488° C, and melts at 405° C., The fluoride, which, is very Soluble in water, hydrolyzes also, but a kind of oxyfluoride of the approximate formula 2 BeO?5 BeF2 can be made from solutions by dessication. The fluoride melts at 800° C, and boils above 1,100° C. It forms very stable double fluorides with alkalifluorides, which have very low melting points and are fairly soluble in water. They are more stable than the analogous fluosilicates and the sodium fluoaluminate cryolite.

Jan 1, 1945

By Robert M. Doerr

Isothermal oxidation kinetics were determined for three grades of Ni and for 99.99 percent Co in Ca and in air from 800° to 1,200° C. The oxidation reactions followed approximately the parabolic rate law. For 99.99 percent Ni in 02 at 1,200° C, the parabolic rate constant was 2 mg cm-2 hr-2. For 99.99 percent Co in dry air, the constant ranged from 1 mg cm-2 hr-2 at 800° C to 18 mg cm-2 hr-2 at 1,200° C; for 99.99 percent Co in 02 the constant was 2 mg cm -2 hr-2 at 800° C and 10 mg cm-2 hr-2 at 1,000° C. For 99 percent Ni in dry air, the constant ranged from 0.2 mg cm 2 hr-2 at 800° C to 3 mg cm 2 hr-2 at 1,200° C. By X-ray diffraction measurements, only divalent oxides were found in the scales. Volumetric and quartz-helix gravimetric methods were used. The volumetric apparatus was designed to permit less stringent restrictions on the corrosion specimens; it was also more convenient to use. The agreement between the weight gain determined gravimetrically and the 02 consumption determined volumetrically was not good enough for direct comparison of gravimetric and volumetric results.

Jan 1, 1963

By F. S. Crawford

The average visitor to a large electric-shovel operation may wonder how electric power can be treated as carelessly as apparently it is in open-pit mining, and how the mining company can string it carelessly along the ground in great, black, hoselike cables, whereas the power company, which has learned to respect his deadly agency, keeps power lines far out of reach. This is explained by the fact that this particular kind of application of power to moving machinery requires the use of trailing cable instead of the more permanent type of construction that permits a moving contact, such as a trolley. The cables are designed to insulate fully the enclosed power lines against damage and loss of current; and employees are taught to handle them carefully, although engineers are not satisfied that the trailing cable is foolproof and are seeking constantly to improve methods and equipment to insure greater safety. In some sections they rely mainly on the construction of the cable and perfection of equipment, while in others additional precautions are taken, such as handling the cable with rubber gloves, slings, tongs, or loops. In some sections no temporary repairs are made to cables, while in others such repairs are made and later are vulcanized in the shop. At some operations the cycle of shovel duties is arranged so that cables are very seldom exposed to flying rock fragments while at others this exposure appears to be unavoidable. Methods of fastening the cable to the shovel frame and transporting the loose cable vary. Inspection and care of the cable are important in insuring its safety and durability. A limited amount of information was obtained by field engineers of the United States Bureau of lines from operators in various parts of the United States, as methods of handling electric-shovel operations differ with the districts; practices followed and equipment used in these districts are described in this circular.

Jan 1, 1936

By L. C. IlsLey

Cooperation between the United States Bureau of Mines and the Safety in Mines Research Board of Great Britain, continuous since 1924, has made possible this and other papers on safety subjects. Grateful acknowledgment is made to representatives of the Board for their assistance in arranging visits to several mine safety stations, and to F. R. Wynne, Deputy Chief Inspector of Mines, for arranging visits to mines in Great Britain and other countries in Europe. During the summer of 1927 the writer had the privilege of visiting the mine safety testing stations in great Britain, Belgium, Germany, and France, in the order named. All of these countries have large coal mines, many of which are rated as gassy. Therefore, when the installation of electrical equipment is contemplated, each of these countries is confronted with the same safety problem as is the United States - the development of electrical equipment that will not ignite gassy atmospheres which through neglect or accident might surround the equipment. The means employed by these countries in safeguarding gassy mines should therefore be of general interest to safety engineers in American coal mines, and it is proposed to give a brief survey for each of the four countries mentioned. The third of these surveys covers conditions in Germany.

Jan 1, 1929

By E. M. Frost

"A new apparatus has been devised for quickly and precisely analyzing natural gas for its helium content. The following outstanding advantages make it far superior to any equipment now available for the purpose.3/4/5/6/1. It enables more rapid determinations to be made.2. It has far greater sensitivity than previous apparatus. 3. It is portable.Fifty or more samples may be analyzed in an 8-hour day with the new apparatus and procedure. A maximum of about 10 samples per day could be analyzed with previous apparatus. In the apparatus described, the volume of pure helium obtained from a sample is determined by measuring the pressures created by that pure helium when it is expanded into a constant calibrated volume. In older methods the pure helium separated from a sample is pumped into a burette and measured at atmospheric pressure. The new apparatus and Procedure used with it reduce the average time for an analysis from about 40 minutes to less than 10 minutes,Samples containing a few thousandths of a percent helium may be analyzed as readily as samples containing 1 percent or more, This was not possible with former apparatus. Duplicate samples containing a few thousandths of a percent helium have been analyzed, results checking to one ten-thousandth of a percent. Attempts to measure a corresponding volume of helium in a burette at atmospheric pressure become futile. The ability to determine very small quantities of helium has become of great importance recently in gas- and oil-field engineering studies such Os the utilization of helium as a tracer gas in following the movement of gases through underground structures.A complete apparatus was recently carried more than a thousand miles in a passenger automobile. It arrived without breakage, was .set up and ready to make an analysis in a few hours. .Former apparatus was not portable. The portability of the present apparatus permits taking the apparatus to the field for more efficient prosecution of field engineering problems. The only services required in the field are electricity, tap water, and a source of liquid air or liquid nitrogen.The principle involved is based upon the fact that large volumes of all the constituents usually found in natural gas, except helium, are adsorbed quantitatively on cocoanut charcoal that has been cooled to the temperatures of liquid air. A volume of sample is measured and transferred to a tube of cocoanut charcoal maintained at the temperature of liquid air. After adsorption of all the constituents other than helium, the charcoal tube is connected to a sensitive pressure-measuring device, and the Percentage helium originally in the sample is calculated from two pressure readings and the volume of the original sample."

Jun 1, 1946

By J. P. Capp

This experiment, one of a series on underground gasification of coal, was an investigation by the Federal Bureau of Mines of hydraulic fracturing as a means of increasing the air acceptance of a coalbed to permit introducing combustion air and removing product gases. Specific objectives of the investigation included: (1) Fracturing a coalbed; (2) determining the distance the coal was physically affected; (3) ascertaining the effect of the fracture on air acceptance of the coalbed; and (4) gasifying the coal. The coal was fractured with a fluid consisting of 15,000 lb. of sand mixed with 10,000 gal. of fuel oil and 5,000 gal. of kerosine, injected at pressures up to 900 p.s.i.g. and rates up to 425 g.p.m. The oil served as the fracturing medium, and the sand as a propping agent to hold the fracture open. From the fracture point, (the place in the bed where the fluid was injected), the fracture extended 200 ft. or more along the face cleats, somewhat less along the butt. cleats, and was confined to the coalbed. At the fracture point, the bed accepted about 500 std. c.f.m. of air, which was an etghtyfold increase. Fracture effects were extensive, as airflow was noted from old mine workings and outcrops 600 to 800 ft. from the fracture point. It is probable the actual fracture was much less than 600 ft. and that normal coalbed permeability beyond the fracture limits was responsible for this flow. This indicated that effects of the fracture extended beyond the area of coal physically affected. Although no attempt was made to gasify coal more than 200 ft. away, these effects plus the natural permeability of the bed likely would permit combustion beyond the outer limit of the fracture. As these experiments continued for more than 2 years, and greater air acceptance due to the fracture was observed at the beginning of each test, it is apparent that the effects of the fracturing persist for a considerable time.

Jan 1, 1960

By C. D. McMaster, John C. Hartley

Three systems that monitor ventilating fans are described . These electronic monitoring systems automatically perform most of the operations required to conform with the provisions of the Federal Mine Safety Code in the event of fan failure or slowdown .

Jan 1, 1964

By W. E. Lamont

The Federal Bureau of Mines, in cooperation with phosphate companies in the Florida land-pebble area, made a comprehensive study of the waste clays, or "phosphate slimes," produced in the mining of phosphate rock in Florida. These slimes represent a significant ecological problem and a major deterrent to effective land recovery in the phosphate-mining areas. Physical, chemical, and mineralogical studies were made of slime samples submitted by 15 of the 16 plants in Florida in an effort to identify factors that prevent successful consolidation of the slimes and subsequent recovery of the mined lands. Results of these studies indicated that the clay mineral attapulgite, a hydrated magnesium silicate, was primarily responsible for the very poor settling characteristics of the slimes, and that the quantity of attapulgite in the slimes effectively controlled the settling rate, pulp density of terminal solids, viscosity, percent solids of filter cake, and flocculant requirements.

Jan 1, 1975

By Hillary W. St. Clair

This report describes a mathematical procedure for analyzing size distribution data by the method of moments. The method was applied to Andreasen's data on a variety of grinding mill products. It was found that the observed size distributions could be represented by gamma and beta distribution functions over a wide range of sizes. A computer program, written in BASIC, is described for calculating moments, distribution parameters, and the weight fraction in any size range.

Jan 1, 1969

By J. E. Gebhardt

External control of the electrochemical potential of a bed of mineral particles has been investigated by the Bureau of Mines as a method for controlling particle inter-action with organic collectors and thus, flotation response. A cylindrically shaped, 200-to 300-g bed of sulfide mineral particles was used as the working electrode to examine the potential distribution in the bed. The dissolved oxygen concentration of the electrolyte had a significant effect on the potential profile across the mineral bed. Low oxygen levels were necessary to achieve uniform electrochemical potential distributions. Flotation separation of a chalcocite-pyrite mineral mixture by controlled potential was achieved using ethylxanthate, but the flotation behavior of chalcocite and pyrite from the mixture does not follow the flotation behavior of the individual minerals. That is, the presence of another sulfide mineral alters the flotation behavior with ethylxan-thate. Galvanic interaction due to mineral-to-mineral contact between chalcocite and pyrite contributes to differences in the recovery. Chalcocite dissolution products had a deleterious effect on pyrite flotation by activating flotation below -0.1 V (saturated calomel electrode) and depressing flotation above -0.1 V. Pyrite dissolution products had no effect on chalcocite flotation.

Jan 1, 1985

By Jerry E. Olson

In 1984, the U.S. Bureau of Mines conducted a mineral survey of the Black Rock Desert Wilderness Study Area (WSA) (NV-020-620), which covers approximately 319,000 acres in Humboldt County, Nevada. About 90% of the WSA is underlain by Pleistocene desert playa sediments; the remainder is comprised of Jurassic-Triassic metamorphic rocks, a Cretaceous intrusive and Tertiary volcanic rocks. Most of the WSA is within a down-dropped fault block of the Basin and Range physiographic province. No mines or evidence of major exploration were identified within the WSA; but five claim blocks within or adjacent to the WSA and zones of anomalous character as defined by the Bureau of Land Management were examined. No mineral resources were identified, but anomalous gold, silver, and indicator element content of samples taken near Pinto Hot Springs indicate resources may exist. Lithium content of samples from near-surface sediments on the desert playa is too low for resources, out geologic conditions are favorable for higher concentrations at depth. Occurrences of zeolites are not considered to be of commercial interest. Approximately 27,000 acres are held under geothermal lease, and most of the WSA is of interest for oil and gas. No evaluation of these commodities was made by the Bureau of Mines

Jan 1, 1985

By Federick W. Miller

The Bureau of Mines has investigated the availability of columbium from 19 deposits (3 producers and 16 nonproducers) in 7 market economy countries (MEC?s). Brazil has the largest recoverable columbium resource, posessing approximately 2.39 million metric tons Wmt), or 69 pet of the MEC total (3.47 Mmt). The Western Hemisphere countries of Brazil, Canada and the United States contain 3.14 Mrnt of recoverable columbium or 90 pnt of the MEC total. Columbium recovered as a byproduct of tin mining is not included as part of MEC resources in this study. Currently producing mines are Araxa and Catalao in Brazil, and Niobec in Canada, These three mines have 2.42 Mmt of recoverable resources or approximately 69 pct of the MEC total. It is estimated that these mines, operating at full capacity, could satisfy cumulative MEC demand (based on an annual growth rate of 5.1 pct) for the next 20 yr. The United States is totally dependent upon foreign sources for its columbium supply. The majority of U.S. columbium is imported from Brazil in the form of steelmaking- grade ferrocolumbium. Canada has been the sole source of pyrochlore concentrates since Brazil discontinued exports in 1981. The United States also imports small (but important) quantities of columbium as columbite concentrates from Nigeria and Brazil, as columbite contained in tin slags from Thailand and Malaysia, and as synthetic concentrates from the Federal Republic of Germany.

Jan 1, 1986

By L. G. Marshall

The geology, mining, beneficiating, types of products, and costs in terms of percent of total costs and of labor, power, and supplies of two crushed-limestone operations in Madison County, Iowa, are described in this paper. The operations are basically similar, differing in refinements in mining, product types, and markets. The operations are comparable as to personnel and as to weighted costs in terms of percent of total costs and in terms of man-hours, power, and sup-plies. The waste-to-stone stripping ratio is 1 to 0.8 at both operations, the powder factor is 0.29 pound of explosives per ton of stone, and daily production is 95 tons per man-shift. Both companies use crawler-mounted diesel shovels for loading, truck transportation, wagon drills, and dry screening.

Jan 1, 1963

By Harry K. James

Experimental studies of the physical and explosion characteristics of pure hydrazine nitrate and multicomponent systems containing hydrazine nitrate, supplemented with an extensive Literature survey, are presented. Such proper- ties as melting point, heat of fusion, density, viscosity, surface tension, thermal stability, decomposition process, detonation velocity, impact sensitivity, and TNT equivalence are included.

Jan 1, 1970

By L. C. IlsLey, Charles M. Means

The descriptive rather than the strictly technical meaning of many of the terms and expressions used in the electrical rules is given in order to assist in their interpге- tation . ALIVE . At a potential measurable with a voltmeter and different from that of the earth or another conductor . (Static charges should be determined with an electrostatic voltmeter . This condition may apply to current - carrying parts , to noncurrent - carrying parts and adjacent material where a failure of insulation has taken place , and to objects having stored or static electricity . ) ALTERNATING CURRENT . A current that changes in direction -- positive or negative-- a certain number of times per second , depending upon the number of poles and speed of the generator . AMMETER. An instrument for measuring current , indicating in amperes . AMPERE . A term applied to denote the rate of current flow . ( Analogous to " gallons per minute " in a hydraulic system . ) APPROVED . Accepted as suitable by a competent committee , board , or organization designated by those adopting the rules . ductors . ARMOR . A steel or equivalent metallic covering for one or more electric con- AUTHORIZED PERSON . Anyone commissioned by the official in charge of the mine or his deputies to carry out certain duties incident to the generation , transformation , and distribution or use of electric energy in the mine , such person being one who is competent within the purpose of the rule in which the term is used .

May 1, 1930

By C. C. Merrill

Columbium, tantalum, titanium, and zirconium are present in solid waste products generated by the chlorination of rutile used for production of titanium tetrachloride (TiC14). The columbium and tantalum were separated from titanium and zirconium by liquid-liquid extraction techniques using a secondary amine. Salts of these elements are in a leach liquor produced by water leaching of mineral waste from the chlorination of rutile. This waste, produced at the rate of approximately 50,000 tons per year, is about 40 wt pct water soluble. Leach liquors, separated by filtration, were further separated into a solid fraction and a liquid fraction by pressure hydrolysis, The solid fraction containing Cb, Ta, Ti, and Zr was dissolved in HC1-HF and used as a feed solution. Columbium and tantalum were removed from the organic extractant with 1 [N] HC1. A miniature 10-stage reactor showed that the columbium and tantalum present in solution could be separated with a continuous flow.

Jan 1, 1972

By R. V. Ramani

"The importance of adequate mine ventilation for good health and safety conditions has been recognized since miners first ventured underground. All over the world, governmental actions on mine health and safety arc directly connected with mine atmospheric environments their assessment and control. These governmental actions have been, and continue to be, motivated by the repeated experience that potential threats from inadequate control can evolve, either suddenly or in the long-term, into unpleasant reality, with catastrophic health and safety consequences. These governmental actions arc also an indication of the remarkable professional progress being made in the field of mine ventilation.Surely, no developed country allows underground mines to operate without strong measures for the control of ventilation under legislation specific to the mining industry. In the United States, the federal government's responsibility for mine safety has evolved over the years through a series of legislative actions beginning in 1865 and continuing through 1910, 1941, 1947 and 1952.The passage of the Federal Metal and Nonmetallic Mine Safety Act of 1966 (the 1966 Metal Act), the Federal Coal Mine Health and Safety Act of 1969 (the 1969 Coal Act) and the Federal Mine Safety and Health Amendments Act of 1977 (the 1977 Mine Act) arc the most important milestones in this long legislative history. The 1977 Mine Act adopted many of the stronger features of the Occupational Health and Safety Act of 1970, perhaps the most significant piece of legislation on workers' occupational health and safety in US history.It is worthwhile to ask, ""How far has the United States come in mine ventilation since the enactment of the 1969 Coal Mine Health and Safety Act?"" This Act and its associated regulations defined in great specificity many standards for healthful and safe operation of a mine and. in some cases, what constitutes good ventilation practice."

Nov 1, 1995