Search Documents

By Raymond M. Stateham

The Bureau of Mines evaluated temperature increases on the heads of resin-grouted bolts as indicators of the integrity of the anchoring of the bolt. Expected increases were calculated by the finite difference method; the calculations were checked by bolthead temperature measurements, both in the laboratory and in the field. The accuracy of the calculations varies with the validity of assumptions necessary to the process. Measurements in the laboratory produced a temperature rise of about 4.00 F on the head of a 4-foot bolt when installed with a full column of resin. This increase remained for about 30 minutes. Similar increases were noted on bolts installed at the White Pine mine, White Pine, Mich., but bolthead temperature increases in the mine lasted only about 10 to 15 minutes. When partial columns (reduced amounts) were used, the temperature increases were smaller.

Jan 1, 1976

By Gordon Bath

During the summer of 1946, the Division of Geophysical Exploration of the U.S. Bureau of Mines established several primary magnetic base stations near important iron-producing districts in Minnesota, Michigan, and Wisconsin. Stations were located in groups of four to six in six separate base-station areas, and each position was marked with a concrete monument. Differences in magnetic intensity between stations in these areas, as well as the difference between each area and a magnetic datum at the magnetic observatory of the Coast and Geologic Survey at Cheltenham, Md., were measured with a modified Askania magnetometer. Measurements also were made with a Hotchkiss superdip to study the usefulness of the stations for the calibration of instruments of this type. The work was planned and supervised by F. W. Lee, chief of the Division of Geophysical Exploration, and Edward F. Fitzhugh, Jr., chief of the Minneapolis Division of the Bureau of Mines. Special mention is due Harold B. Ewoldt, Bureau of Mines engineer, for his assistance in the field work, especially in locating and establishing monuments. Special mention also is due Clyde L. Holmberg, of the Bureau of Mines, for the magnetic measurements made with the Hotchkiss superdip. Helpful suggestions were received in the field from H. L. James, of the U. S. Geological Survey. Acknowledgment is made of the cooperation of Stephen Royce, Irving E. Beckwith, Arthur Johnson, and Josiah Royce of Pickands, Mather & Co., and A. E. Matson, of Butler Bros. The U. S. Coast and Geodetic Survey furnished daily magnetograms from the Cheltenham Magnetic Observatory as well as calibration equipment and values of absolute magnetic intensity. Short-term forecasts of ionospheric conditions were obtained from the National Bureau of Standards.

Jan 1, 1951

By Albert L. Toenges

[During the past few years there has beer trend away from locomotive haulage of coal from the loading point to the preparation plant of bituminous-coal strip, miner to motorized. haulage. The question has arisen whether this is always economical, and the purposes of this investigation is to determine, if possible the economic limit for motorized haulage. The operators of strip coal mines and of open-pit ore mines have shown great interest in this problem, and it is thought that the findings of this investigation will. Provo helpful to them.]

Jan 1, 1938

By A. Visnapuu

The Bureau of Mines, as a part of its goal to minimize occupational hazards associated with mining and mineral processing operations, has developed and field tested a compact exhaust air muffler for mechanized, jumbo-mounted pneumatic rock drills. The muffler is constructed of 1/8-inch sheet steel and has nominal dimensions of 1-3/4 by 9 by 13 inches. A directed air passage, flexible neoprene baffles, and an expandable slit-type outlet are incorporated to reduce drill exhaust air noise and eliminate muffler icing. Field tests in actual mining operations showed a l5-dbA reduction in exhaust noise and an 8-to 12-dbA reduction in overall drilling noise with no icing problems or decrease in drill performance. Data are presented on muffler construction, laboratory, and field test results.

Jan 1, 1979

By Gary P. Sames

This report discusses some practical applications of a geotechnical investigation conducted by the U.S. Bureau of Mines that can help mine operators meet revised Federal regulations in their roof control plans. The investigation, designed to characterize roof conditions near the coalbed outcrop in drift coal mines in eastern Kentucky, revealed that weathered stress-relief joints near outcrop are crucial ground control factors in the region. The joints' origin and character were determined through underground mapping of many joints in coal mine roof and detailed observations and measurement of joint trends and physical characteristics in widely separated strip mine highwalls and roadcuts. This resulted in an understanding of stress-relief-joint patterns and the effect of various rock types on the intensity of weathering in the joints. That information is used in this report to show how stress-relief joints contribute to roof failure and how, through improved roof support and mine planning, safer roof support plans can be developed.

Jan 1, 1992

By K. K. Kelley, L. B. Pankratz

The heat contents of four silicate minerals -- akermanite , cordierite , gehlenite , and merwinite --were measured from 298 ° to around 1,700 ° K by the dropping method . The results were compiled into tabular and equation forms suitable for thermodynamic calculations . The heat contents of these compounds are nearly additive with respect to their constituent oxides .

Jan 1, 1964

By R. D. Wilson

Ten to twelve million tons of dust is produced by cement kilns annu-ally in the United States, resulting in a serious waste disposal problem. The Bureau of Mines investigated two alkali volatilization methods for converting this dust into materials for making portland cement and a useful potassium product. Portland cement kiln dust was found to be composed of finely ground cement raw materials (CaC03 and 8i02) having a layer of alkali sulfate (K2S04 and Na2S04). In this form, it cannot be directly recycled to cement kilns because concrete is weakened by a reaction between the alkali and the aggregate. Portland cements with 28-day strengths above 5,000 psi were produced from low-alkali residues using sintering and melting methods. For nearly complete removal of alkalies, primarily potassium sulfate, from cement kiln dust, a temperature above 1,300° C and a reducing atmosphere were required.

Jan 1, 1986

By Thomas Gales

Longwall mining of thin shallow coal seams utilizing open pits is technically feasible. The thinnest coal seam which can be mined using available technology is 34 inches. The capital expenditure for a 1,000,000 ton per year operation is $15,494,000, and the projected rate of return is 5 percent. Similar statistics for a conventional area surface mine are S18,937,000 capital and 14 percent rate of return. The longwall surface mining method disturbs 63 acres of land per 1,000,000 tons, and the conventional area surface mine disturbs 198 acres A significant bibliography of the technology involved is included.

Jan 1, 1976

By D. E. Wolfson

As part of its overall program of coal-carbonization research, the Bureau of Mines is studying the coking properties of coals from various fields of this country. Few of the coals included in this survey are used for the manufacture of metallurgical coke, although some well-known coking coals necessarily are tested to provide comparative data, particularly on blending properties. The overall objectives of the study were given in detail in a previous report.3/ The inherent suitability of coal for metallurgical purposes, as distinguished from economic considerations, depends primarily on (1) the available reserves, (2) chemical composition, (3) preparation characteristics, and (4) carbonization behavior. These items are considered in selecting coal for carbonization tests.

Jan 1, 1956

By L. E. Green

For shortwall mining to be profitable, the additional capital investment of about $1 million for shortwall roof supports must be offset by decreased total operating costs and/or increased coal production. The Bureau of Mines therefore conducted a demonstration project to compare shortwall and room-and-pillar mining. Daily two-shift production from the bureau of Mines-Beth-Elkhorn Corp. shortwall demonstration n project averaged 975 tons of raw coal, compared with 905 tons from a room-and-pillar unit operating undo r similar conditions. The estimated direct operating costs for the shortwall and room-and-pillar unite were $4.21 and $4.03 pier ton, respectively. The profitability of the shortwall system was found to depend not only on the increased depreciation cost of the powered roof supports and the decreased cost of supplies and materials but also on such factors as the fixed and variable indirect costs and the selling price of the coal. Shortwall mining was demonstrated to be a viable alternative to room-and-pillar mining.

Jan 1, 1977

By R. T. MacMillan

Many bench-scale tests and studies have been conducted in developing and testing a chloride-volatilization procedure Ear treating low-grade manganese ore from the Maple Mountain-Hovey Mountain deposit of Aroostook County, Maine. The ore, averaging 10 to 12 percent Mn, contains manganese in several forms and is resistant to concentration or extraction by usual physical and chemical procedures. Over 90 percent of the manganese, content of the ore has been recovered using a chloridizing roast in which the ore was heated at 950°-9b0' C. in a circulating stream of hydrochloric acid gas. Chlorides of manganese and iron were volatilized and swept to a fume collector, where they were condensed and separated from the [as] stream. Operation of a small, 1-pound-per-hour shaft Furnace produced enough chlorides for studying other factors in an integrated process such as: (1) Conversion of the chlorides to oxides; (2) recovery of HC1 gas of suitable concentration Ear recycling to the chloridizer; and (3) control of the Mn-Fe ratio in the oxide product to produce a suitable feed for ferromanganese production.

Jan 1, 1956

By John P. Capp

Addition of sintered fly-ash/bottom-ash mixtures to rubber formulations failed to increase the skid resistance of the resulting products. Wear, tensile and hot-tear strengths, and resilience of the ash-rubber material, as determined in laboratory tests, were significantly less than that of comparable rubber. The material appeared unsatisfactory for automobile and truck tire manufacture, but might prove suitable as a filler in other rubber goods. Raw fly ash could not be satisfactorily compounded with rubber.

Jan 1, 1972

By Walter T. Lewiecki

Bauxite was first discovered in-the United States near Rome, Ga., in 1887, Approximately 400,000 tons of bauxite ranging from 46 to-62 percent alumina were mined in the area from 1888 to 1930. In February 1943, The Republic Mining & Manufacturing Co. installed a dryer and began mining and reworking dumps from the old bauxite mines. Some 3,000 long tons were dried and shipped to the chemical industries from March 1943, to June 30, 1943. In 1941 and 1942, representatives of the Bureau of Mined and the Federal Geological Survey/ visited this area and proposed an exploratory project that at first was to be confined to the Heritage district northeast of Rome (see fig; I). The Bobo district, southwest of Rome, was to be explored after work .1n the Hermitage district was completed. The Hermitage district comprises an area of about 50 square miles in the northwest quarter of Bartow County and the adjacent portion of Floyd County. It is bounded on the north by the Gordon County line, on the east by U. S. Highway 41, on the south by U. S. Highway 441, and on the west by State Highway 53.

Jan 1, 1949

By B. W. Naugle

This report describes the carbonizing properties of coals from the principal beds in Cambria County, Pa. Samples of coals from Upper and Lower Freeport and Upper and Lower Kittanning beds having estimated minable reserves of 50-million tons or more were studied by the Bureau of Mines. Cambria County coals rank either as medium-or low-volatile bituminous. A preparation study indicated that all coals tested in this county, except one sample from the Lower Freeport bed, were responsive to cleaning and would yield a product with satisfactory chemical properties for metallurgical coal. All coals tested from Cambria County yielded strong coke; however, they expand excessively when carbonized singly, and should be used only as minor constituents in metallurgical coking blends when carbonized in slot-type ovens.

Jan 1, 1959

By Cavallaro. J. A.

This report presents the results of a washability study of 455 raw coal channel samples with special emphasis on sulfur reduction. These raw coals contained on the average 14.0 percent ash, 1.91 percent pyritic sulfur, and 3.02 percent total sulfur. The complete washability data are presented for each sample processed. A statistical evaluation is included for the coalbeds from which more than 10 samples were collected and for the geographical coal producing regions. A graphical summation is presented for the coal producing regions and selected coalbeds. Finally a similar statistical evaluation is included showing composited data interpolated at Btu recovery levels of 50, 60, 70, 80, 90, and 100 percent. Graphical summations are presented for the various coal producing regions. Generally, significant sulfur reduction is achieved if the coals are crushed to a finer size and the higher specific gravity increments are removed. If a 50-percent Btu recovery was acceptable, then 32 percent of the samples tested could be upgraded to meet the current Environmental Protection Agency (EPA) standard of 1.2 pounds of S02 emission per million (MM) Btu when crushed to 14-mesh top size and separated gravimetrically.

Jan 1, 1976

By Denis Dwyer

[This paper describing mining, treatment methods, and costs at Plant No. 1 of the Western Indiana, Gravel Co. at Lafayette, Ind., is one of a series on gravel and sand mining being prepared for and published by the U. S. Bureau of Mines. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual producers, as well as to industry as a whole. On the other hand, operating costs are essential to e technical discussion and study of the methods employed, The attention of the reader is specifically called to this differentiation in order that no Misunderstanding of the scope of the cost tabulations shall ensue.]

Jan 1, 1933

By Don Steffa

Drift mining, according to California mining terminology - and it is distinctly a California development - is the blocking out and extraction (breasting) of the auriferous gravels of an ancient buried stream either through tunnels, inclines, or shafts; it is one of the minor divisions of the larger classification known as placer mining. The contribution of each of these divisions and of lode mining to the gross production of gold in California totals as follows:3 [ ] The total amount of gold recovered from the placers of California from 1848, when Marshall discovered the precious metal in the mill race at Coloma, to 1928, was $1,226,515,404. The same period saw a total gold production from all operations of $1,823,562,360.

Jan 1, 1932

By G. W. Elger

The Bureau of Mines investigated the conversion, at both laboratory and pilot plant scale, of a low-grade ilmenite to chlorination-grade feedstock that could substitute for imported rutile used to produce titanium tetrachloride. The concentrate was derived from the Tahawus, NY, lode deposit of ilmenite-magnetite in rock that contains anorthosite and gabbro. Charges of the ilmenite concentrate, containing 46.6 wt pct Ti02 blended with soda ash, were carbothermically reduced in an electric arc furnace, which separated most of the iron and left a high-titanium slag. However, the slag contained Ca, Mg, and Mn constituents that rendered the material unsuitable for continuous chlorination by causing plugging problems. After being ground and pelletized, the slag was reacted with S02 and air at 7000 to 9000 C, which selectively converted the harmful impurities to soluble compounds that were removed in a subsequent water or dilute HCI leach. In laboratory tests, the combined levels of harmful impurities were decreased from 5 to as low as 0.5 wt pct in leached slags. In pilot plant tests, leached slags sulfated at a rate of 10 lb/h averaged 85.5 wt pct Ti02 with pertinent impurity levels averaging 1.86 wt pct. The leached slag was successfully chlorinated in a laboratory fluidized-bed reactor at 9500 C to extract titanium as TiCI4.

Jan 1, 1986

By Terry S. Cory

This report is a comprehensive summary of the results of the propagation measurements program conducted for the US Bureau of Mines under Contract H0366028. Data was gathered in the MF frequency range from a cross sample of six mines representative of the industry having typical wireless requirements. From the raw data which was gathered, a logical method of data reduction is presented which culminates in a set of average attenuation characteristics for all mines visited. These characteristics define a typical MF wireless system when the communication range requirements are known. Direct through-the-earth propagation and the range enhancement mechanism due to coupling on and off conductors are evaluated and related to the planning of a typical wireless MF communications system.

Jan 1, 1977

By A. Soderberg

This paper describing the mining practice at the Utah Copper Co., Bingham Canyon, Utah, is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The Utah Copper Co. operates the low-grade open-out copper mine at Bingham Canyon, Utah, which is 30 miles in a southwesterly direction from Salt Lake City. In addition to the mine the company operates two flotation concentrators, the Magma plant and the Arthur plant, which have a combined capacity at maximum metallurgical efficiency of 60,000 tons daily. The concentrators are at Magna, about 18 miles from the mine. The company operates its own standard-gage railway, known as the Bingham and Garfield Railway, between the mine and the mills (fig. 1). Concentrates are smelted at the Garfield smelter of the American Smelting and Refining Co., situated 4 miles from the mills.

Jan 1, 1930