Search Documents

By D. Harrington

"The recent discovery and exploitation of petroleum territory have resulted in the enactment of new petroleum laws in most of the South American Republics. The activities in the discovery of these new fields were engendered by the knowledge of the fact that present producing fields must within well defined periods be exhausted. Oil operators were willing to take the initial steps in exploitation in the absence of legislation that applied strictly to petroleum operations. The enactment of modern legislation in many of these Republics encouraging and protecting exploitations may cause tremendous oil activities in these countries, and the results may be comparable with the magnitude of the undertakings and the prestige of the companies now entering this territory.These, oil fields are admirably located for convenient distribution of petroleum by water to all the Nations using oil as fuel for shipping and industrial concerns. The oil markets of the western coast of South America will derive immense benefits from the Panama Canal. This navigation route brings these markets into direct ocean shipment with the Atlantic coasts of the Western and Eastern Hemispheres.One deterrent to oil production in the Republics of South America is the want of inland. transportation facilities, but the recent laws of these Republics without exception provide for acquiring rights of way for pipe lines and other modes of transportation; and doubtless the great interests and. syndicates already operating in these regions will, as production increases, provide ample pipe line transportation sufficient to convey to the coast the oil produced. It way be assumed, from the legal guarantees afforded, and from operating equipment and machinery that are now being concentrated that refineries will be erected at shipping points for the purpose of making these petroleum products accessible to the world."

Jun 1, 1921

By J. J. Forbes

The investigation of major and minor coal-mine disasters has been a routine function of the Bureau of Mines since its inception in 1910, and the facts obtained during such investigations have been used as a basis for determining the precautions that the managements and employees of many mines are observing to forestall similar occurrences. The Bureau has conducted research on roof-control and other mine problems, but a comprehensive study of other fatal accidents was not attempted until February 10, 1950, when the policy of investigating all coal-mine fatalities in the United States was approved by Bureau of Mines Director James Boyd. The investigations are being conducted by Federal coal mine inspectors functioning under the provisions of the Coal Mine Inspection and Investigation Act of May, 1941, Public Law 49; and reports covering the investigations are distributed to management, the State mine-inspection agency, and representatives of the mine workers' organization have jurisdiction at the mine.

Jan 1, 1951

By Lathrop E. Roberts

The opinion is general among smelter operators that magnetite formed in the converter and reverberatory furnace has much to do with the loss of copper in the slag. Its action appears to be due in part to its relatively high infusibility, chemical stability, and specific gravity, as a result of Which it tends to form a layer of highly viscous "magnetite mush" between slag and matte. Particles of matte which might otherwise settle out of the slag are unable to pass through this layer. Maier and Van Arsdele have shown that the inclusion of grills of matte in the slag is also at tires very probably due to chemical reaction between magnetite and the constituents of the matte. In smelter control and in any laboratory study of slats the determination of magnetite is therefore a matter of some importance. The difficulties in the ray of making such a determination with any accuracy are rather obvious. Iron may occur in slag as ferric oxide, magnetite, various intermediate oxides, sulphides, silicates, as free metal, and in solid solution of several of these substances. Even if only the total iron content is to be determined, accuracy can be obtained only by painstaking and time-consuming separations from interfering elements. The determination of ferrous, ferric, and free iron in the presence of each other is a difficult matter under the most favorable conditions, and when present in a slag the difficulties are increased by the refractory nature of the sample, by the presence of sulphides, and by such elements as vanadium and molybdenum.

Jan 1, 1931

By Lathrop E. Roberts

[The opinion is general among smelter operators that magnetite formed in the converter and reverberatory furnace has much to do with the loss of copper in the slag. Its action appears to be due in part to its relatively high infusibility, chemical stability, and specific gravity, as a result of which it tends to fern a layer of highly viscous. "magnetite mush" between slag and matte. Particles of matte which might otherwise settle out of the slag are unable to pass through this layer. Maier and, Van Arsdale4 have shorn that the inclusion of prills of matte in the slag is also at times very probably due to chemical reaction between magnetite and the constituents of the matte. In smelter control and in envy laboratory study of slats the determination of magnetite is therefore a matter of some importance. The difficulties in the ray of making such a determination with any accuracy are rather obvious. Iron may occur in slog as ferric oxide, magnetite, various intermediate oxides, sulphides, silicates, as free metal, and in solid solution of several of these substances. Even of only the total iron content is to be determined, accuracy can be obtained only by painstaking and time-consuming separation ions from interfering elements. The determination of ferrous, ferric, and free iron in the presence of each other is a difficult matter under the most favorable conditions, and linen present in a slag the difficulties are increased by the refractory nature of the sample, by the presence of sulphides, and by ouch elements as vanadium and molybdenum.]

Jan 1, 1931

By STUART R. BRINKLEY, Ruth F. Brinkley

This same phonomonon of diffraction may be transposed into the X-ray domain. All that is necessary is to reduco, in the samo proportion, the wavo length of the light and the diameter of the particlo; thus, with radi- ations whose wave length is of the ordog of angstroms, the dimensions of the active particles go from 10 to 100 A that 18, the dimensions of col- loidal particlos. The evidence of this fact is shown by the following experimental schomo (fig. 1a): A narrow beam of X-rays passes through a thin layer of a modium containing micelles; the photographic film is placed a few centimeters behind the sample, and a small absorbing screen stops the direct beam in order to prevent its fogging the film. The intersect of the direct beam is surrounded by a narrow spot whose blackness decreases with the distance from the center. We will call this the spot of central diffusion (fig. 1b). The phenomenon, in spite of its relatively reat intensity, has been observed only by a few authors, who have simply given a qualitative description without attempting any quantitative de- ductions. This is due to the fact that observation of this phenonenon is not possible with the apparatus generally used to obtain X-ray diagrams, because the parasite foggings in the vicinity of the incident beam are sufficiently important to hide those produced by the sample. With the monochromator, however, used by us to obtain Debye-Sherer diagrams, this parasitic diffusion can be totally suppressed. In this way our attention was again directed to the spot of central diffraction, and we were led to make a detailed quaititative study of it.. then several papers have been published on this subject. Hosemann, using methods of calculation outlined by us, has extended them to the special case of fibrous substances, Kratky, on the other hand, starts from an entirely different theoretical point of view; ho examines the case, not of scattered particles, but of closely packed particles. 6ince We will now describe the experimental methods, summarize the calcu- lations needed in the elaboration of diagrams, and finally review the first results obtained in the vast domain of these new physical-chomical studies.

Dec 1, 1946

An active list of permissible explosives was published in July, 1931, as part of United States Bureau of Mines Report of Investigations 313, under the title of "Active List of Permissible Explosives and Blasting Devices Approved Prior to June 30, 1931." Changes in that list were authorized in August, September, October, November, and December, 1931, and. January and March, 1932, as published in Reports of Investigations 3l40, 3147, 3l50, 3155, 3158, 3161, and 3163, respectively. By these changes the following explosives were added to the active permissible list: [Austin Red Diamond No. 1, L. F. Gel-Coalite W. L. F. Austin Red-Diamond No. 5, L., F. Gen-Gel No. 2. Black Diamond Nu-Gel No. 1 Genite C-1 Burton 1, L. F. Liberty No. 4 Burton 2, L. F. Liberty No. 5 Burton 10, L. F. Peerless D Burton 12, L. F. Permigel 1, L. F. Burton F, L. F.]

Jan 1, 1932

By R. Karl Zipf, David Newman

The objective of this is paper is to review the current state of knowledge and practice in highwall mining (HWM). HWM has become a widely-applied method in surface mining, commonly used alone or in conjunction with contour or slot mining. It provides 800-feet to 1,200-feet of additional recovery when the economic stripping ratio is reached in contour mining or in slot mining when surface access to a reserve is limited. A significant attribute of the highwall miner is its versatility. HWM has been used successfully to mine abandoned pre-reclamation law highwalls, points or ridges uneconomic to mine by underground or other surface methods, outcrop barriers left adjacent to underground mines, separate benches of the same seam where the parting thickness or quality differences between benches render complete extraction uneconomic, previously augered areas containing otherwise inaccessible additional reserves and close or widely spaced multiple seams. The theory and design methods to assess roof, pillar, and floor stability are presented followed by three case histories. Simple design charts for sizing HWM web and barrier pillars are also presented. A recommended web pillar width may be obtained from the design charts given the overburden depth, the HWM cut width, and the mining height. Given the depth and panel width for a set of HWM cuts, another set of charts gives a suggested barrier pillar width. The case histories, from Northern and Southern Appalachia are used to illustrate the application of rock mechanics to quantify the stability of the highwall, roof, web pillars, and floor. The case histories involve 1) mining through a previously augered highwall, 2) mining under back-stacked spoil and 3) selective mining of closely spaced benches of the same seam. Because each site is unique, the appropriate pre-mining geotechnical analyses range from the calculation of roof, web pillar, and floor bearing capacity stability factors to detailed numerical modeling of the auger and underground mine workings. When operating in the vicinity of existing underground mine or auger workings, the determination of ground deformation and strains resulting from highwall mining is a necessary facet of a ground control investigation.

By P. A. Croce

A total of 17 mine gallery fire tests (23 including sub-tests) were completed during this report period (10/1/76 - 11/30/77), directed at identifying a hazardous timber-set fuel-loading in a mine passageway that is otherwise free of combustibles. Results of these initial tests show that the capability of a particular fuel loading for propagating a fire is dependent upon the imposed ventilation air velocity and the ignition intensity, although this dependency needs to be better defined. It is also apparent that care must be taken when relating gallery test fire behavior to actual mine fire behavior, because of the restrictive length of the gallery. Present data indicate that some modification to the instrumentation scheme may be advantageous before proceeding with future tests.

Jan 1, 1978

By Alla D. Mah

The heats of combustion of three chromium carbides, Cr23C6, Cr7C3, and Cr3C2, were determined by combustion calorimetry. Heats of formation calculated from the results follow: ?Hf°298 (Cr23C6) = -94.7 ± 5.0 kcal/mole, ?Hf°298 (Cr7C3) = -43.3 ± 1.7 kcal/mole, and ?Hf°298 (Cr3C2) = -22.5 ± 0.8 kcal/mole.

Jan 1, 1969

By R. H. Grau, A. Sainato, S. J. Schatzel, T. M. Kohler, A. T. Iannacchione

This Bureau of Mines research study found gas emission rates from an advancing face, and flows and pressure of gas from an exploration drill hole were dependent upon the geology of salt encountered in a domal salt mine. Normal production-grade "pure" salt adjacent to an anomalous' zone was found to have a methane emission rate of less than 5 ft3/ ton (0.1 m3/t) of mined salt from a room advanced by a continuous miner. Extremely low gas flows [less the 4 ft3/h (0.1 m3/h)] and lack of pressure buildup were also observed from this normal salt in a 154-ft (47-m) exploration drill hole. These data indicate that methane emissions should not be a problem when mining in this type of salt. In the adjacent anomalous zone, methane emission rates ranged from 15 to 70 ft3/ton (0.4 to 1.8 m3/t) of mined salt from an advancing face. Gas flows of approximately 42 ft3/h (1.2 m3/h), and pressures in excess of 900 psig (6,200 kPa) were observed in an exploration drill hole when the anomalous zone was encountered. This information suggests a greater methane emission hazard from the anomalous zone than from the associated normal salt. If this trend of increasing emissions problems associated with anomalous zones of salt is common with similar anomalous zones encountered or observed in other domal salt mines, then special control strategies should be employed to minimize this potential mining hazard.

Jan 1, 1984

By R. G. Meara, O&apos

The land-pebble district of Florida, wnich in 1928 supplied 96.7 per cent of the phosphate production of that State and 82 per cent of the domestic requirements of the United States, is centered in Polk and Hillsboro Counties about 30 miles east of Tampa The deposits are unconsolidated sediments occurring as beds of phosphate matrix overlain by a mantle of barren sands and clays. The matrix consists of a mixture of sand (quartz grains), clay, and phosphate rock in which the coarsest sand is much finer than the coarsest phosphate; that is, the sand is segregated in the fine material. Before the introduction of classifiers the concentration consisted of log washing, and screening at about 20-mesh, which was usually the finest size that could be taken to maintain commercial grade, 66 per cent B. P. L. (bone phosphate of lime) or more. When classifiers were introduced some of the fines that had escaped at the head of the washery and some of the minus 20-mesh material isolated during the washing and formerly lost supplied the feed. During October, 1927, the United States Bureau of Mines in cooperation with the University of Alabama and the Missouri School of Mines and Metallurgy began to investigate the amenability of phosphatic sands to gravity methods of concentration. The work was under the immediate supervision of B. W. Gandrud, acting supervising engineer of the Southern Experiment Station of the U. S. Bureau of Mines at Tuscaloosa, Ala., and Will H. Coghill, supervising engineer of the ore dressing section of the U. S. Bureau of Mines. More comprehensive testing followed and in the early part of 1930 some of the companies cooperated with the bureau and the above-mentioned institutions in conducting a series of tests on hydraulic classification and tabling. The results indicated that marketable concentrates could be obtained with a recovery of 25 to 45 per cent of the phosphate formerly lost. As a result two companies have introduced hydraulic classification to treat the current tailings, and one of them has substituted classifiers for the 20-mesh screens which had been unsatisfactory. Because the phosphate grains and quartz grains have nearly the same specific gravity, the use of concentrating tables by the customary methods is not applicable. The washeries included in the following report are designated as Nos. 1, 2, and 3.

Jan 1, 1931

By M. S. Oudenhoven

This Bureau of Mines investigation was conducted to obtain an experimental solution of stress changes in the vicinity of a circular opening in an infinite plate. Plates were stressed biaxially in compression and subjected, by four different-length shoes, to a uniform pressure at opposing points on the opening periphery. The principal stresses along the vertical and horizontal axes, which result from peripheral pressure, were obtained from the photoelastic analysis of four frozen-stress epoxy models. These principal stresses were then super-imposed on the mathematically determined principal stresses (along the same axes) obtained from a theoretical biaxial stress field in which the magnitude of the lateral pressure was one-third that of the vertical pressure. The results indicate that an increase in shoe length increases the radial compressive stress and the tangential tensile stress (except tangential compression at r/a = 1, which exists for all shoe lengths). Also, a partial control of the stresses within one-half radius of the opening surface is accomplished by a change in the magnitude and placement of peripheral pressure.

Jan 1, 1966

By C. C. Shale

Electrical resistivities for various coal ashes in air and in a nitrogen atmosphere are given over the range 100° to 1,500° F. Resistivity of low-carbon ash in air is very high at low temperature, rises to a maximum at about 250° F, decreases very rapidly with increasing temperature to about 800° F, then decreases gradually to approach an asymptote at 1,500° F. Resistivity of high-carbon ash in air follows this same general trend at values which are much lower and are proportional to the carbon content. After the carbon has been burned off, resistivity of the remaining ash approaches the high values corresponding to low-carbon ash of similar chemistry. Two factorial experiments show the effects of temperature, particle size, chemical content, and compressibility on the resistivities of four fly ashes of widely different chemical composition in the temperature range proposed for coal-fired turbines. Resistivities of all low-carbon ashes tested fall in the range 106 to 107 ohm cm at 1,500° F and should be removable by electrostatic precipitators. Ashes containing carbon in excess of about 8 percent, however, have low resistivity (as determined in nitrogen), especially at high temperatures. Therefore, high-carbon materials may not be collectable in precipitators because the resistivity is below the minimum value necessary for precipitation. Consequently, high carbon residues from partial combustion of coal probably could not be removed effectively at high temperatures.

Jan 1, 1968

By W. Dan Walker

In an effort to keep mine hoist accidents to a minimum and to impart to managers and workers the essential elements that enter into safe installation and maintenance of hoisting equipment, the Bureau of Mines presents this Information Circular as a guide. Hoisting of men and materials is an essential operation in many mines and has become so commonplace that some persons are likely to ignore day-to-day inspections or become lax in the operating phases. With proper maintenance and operation, hoists can be exceptionally safe. However, lack of strict attention can invite tragedy or costly shutdowns.

Jan 1, 1961

By Richard L. Rains

The 15,770-acre Worm Creek Roadless Study Area is in southeastern Idaho about 8 miles (mi) west of the northern portion of Bear Lake. U.S. Bureau of Mines personnel examined the roadless, area during the summer of 1984. No mineral resources were identified within the study area. There were no mines or mining claims in the study area in 1984. However, the study area is blanketed with oil and gas leases, but no known productive horizons have been identified within nor nearby. The roadless area is in the Cordilleran fold-thrust belt and is underlain by Paleozoic and Mesozoic marine strata more than 50,000 feet thick. The trace of the Paris thrust fault is 2 to 3 mi east of the study area and has an eastward displacement of about 4 to 7 mi.

Jan 1, 1985

By Franklin D. Slagle

Porosity and bulk-and sand-grain-density values were determined for 2,040 core samples of 30 formations from 47 wells in New York, Ohio, Pennsylvania, and West Virginia, and are compiled for petroleum industry use in well-log evaluation and geologic studies.

Jan 1, 1967

By L. H. Harrison

In coal mines equipped with electrically driven mechanical mining equipment, the problem of protection for electrical circuits and machinery important, because the hazards of fires and explosions resulting from electrical failures is greater than in most other industries. There is need for better methods and improved protective devices for this service. Studies and tests designed to determine possible value of the short-circuiting contactor as an electrical device for coal mine service were investigated. Preliminary made to determine the operating characteristics of the device, after which tests were made under actual service in three coal mines. Ordinarily, electrical protection in coal mines is divided into three classes, as follows: 1. Overload protection that is intended to protect against damage from overheating and excessive mechanical strain due to overloading. 2. Short-circuit protection that provides a means of de-energizing the equipment instantly when an accidental short circuit occurs in the equipment or on the power system. Short cm protection tends to damage from fires and, explosions resulting in the dissipation of large amounts of electrical energy in a short circuit. 3. Ground fault protection that, in its various forms, is intended, to maintain the frames of electrical equipment at or near the same potential surfaces in contact with the earth for the purpose of safe-guarding human life.

Jan 1, 1951

By Louis A. Panek

Determining the change of stress in rock based on measurements of the deformation of a drill hole is a procedure that is increasing in popularity. A closely related procedure involves the applicat10n of this principle to determine the existing stresses in a rock medium, by cutting free (core drilling) an annulus containing the drill hole. In this Bureau of Mines report, expressions are derived from which one can calculate the stress ellipsoid--the three-dimensional change of stress, or the existing three-dimensional stress field, as the case may be. Study of these equations shows that the stress components in three dimensions can be determined by measurements in only two drill holes, and yields general principles that are useful in planning an efficient program of drilling and measurement. Procedures are given for calculating the least squares estimates of the stress components and their standard errors, and for evaluating or comparing calculated values by means of standard statistical inferences.

Jan 1, 1966

By Rogers F. Davis

This publication has been prepared to supply manufacturers and industrial users a listing of mobile diesel-powered equipment and subassemblies approved and certified by the Bureau of Mines for use in noncoal mines. Testing of diesel-powered equipment is one phase of the Bureau's program of health and safety that concerns approval of electrical and diesel equipment designed to prevent explosions, fires, shocks, or toxic hazards in underground mines, when such equipment is used and maintained properly. Manufacturers submit machinery and component parts to the Bureau for study of their design, safety features, and use. Equipment must pass exacting tests and must meet strict requirements established through research and experience and listed in the Bureau's permissible schedules before the Bureau approves it as permissible for safe use in mines.

Jan 1, 1963

By Russell J. Miller

A high-pressure intensifier system was designed, constructed and field tested as part of a program to determining the feasibility of applying high-pressure water jets on conventional mechanical rock excavation equipment to increase advance rates. Also developed were a high-volume swivel, capable of transferring the high-pressure water to a rotating cutterhead and manifold system for locating and protecting the jets on the cutterhead. Field tests were conducted in a granite quarry near Skykomish, WA, approximately 90 miles east of Seattle. The concept of improving excavation rates by using water jets to assist mechanical cutting was proven to be successful, with an average increase in excavation mete of 50 to 60%. For some tests, the excavation rate was more than doubled. Machine torque requirements were reduced approximately 25% when the water jets were used. It was suggested this was due to reduced cutterhead friction in the presence of the water jets. A comprehensive economic analysis was undertaken as part of a concurrent study to determine the degree of cost benefits attainable from increased advance rates. Very significant savings were seen to be possible. It was concluded that the basic concept of combining a water jet capability with a mechanical excavating machine is definitely possible.

Jan 1, 1976