Search Documents

To reduce equipment operator exposure to respirable dust in enclosed cabs by examining the effectiveness of retrofitting air pressurization and filtration systems on existing cabs.

Jan 1, 2001

By N. Greninger

The Bureau of Mines examined the possibility of a seasonal variation of respirable dust concentration in U.S. coal mines. The first step was to review company and MSHA-inspector dust samples that had been collected during the past several years in 14 selected mines for compliance purposes. Results indicated severe scatter in data; most standard deviations of the dust concentrations measured in winter and summer months were comparable in magnitude with the mean values of dust concentrations for the seasons. Therefore, a detailed statistical analysis was conducted. At the 90% confidence level, the company samples of three mines had winter means 0.15 to 0.54 mg/m3 higher than the summer means; six mines had negligible seasonal variations; and five mines had winter means that ranged from higher to lower than the summer means. Inspector data, however, were too sparse for analysis. In view of both the low frequency of occurrence of a seasonal effect and its wide scatter in several of the mines, the study was ended with the conclusion that seasonal varia-tion in respirable dust levels, in general, is an insignificant factor.

Jan 1, 1986

The coal-bearing areas of Kansas cover approximately 18,800 square miles (23 percent of the state's total area). Coal in Kansas ranges from lignite to high volatile bituminous, located principally in the south-eastern part of the state. Kansas reserves are estimated to be 987,500,000 tons, approximately 0.2 percent of U.S. reserves. Coal beds generally occur in thin seams up to five feet thick. The overburden-to-coal stripping ratios in Kansas are among the highest in the nation, typically 20 to 1, with some ratios up to 35 to 1. The first commercial coal mining operation in Kansas opened in 1865 at Fort Scott in Bourbon County. As in other states, coal production in Kansas increased during the industrial revolution, and then fell as industry converted to alternative fuels. Production peaked in 1916 and 1917, with annual production of 7,250,000 tons. Coal production today is by surface mining methods. The Kansas regulatory program was approved April 14, 1982; the Abandoned Mine Land Program was approved February 1, 1982; and the emergency program authority was approved January 10,1989.

Jan 1, 1992

By Forrest T. Moyer

INJURY experience and related employment information are presented in the chapter for the coal-mining, coking, oil and gas, peat, and native asphalt industries in the United States for 1964. No attempt has been made to combine these data and present injury-frequency rates reflecting the mineral-fuel industries because the hazards of the separate industries are not comparable. All rates in the text are calculated separately on data before rounding, hence component rates may not add to the total rates shown in the tables. Tabulations showing the trend of injuries and employment for all mineral industries are presented in Volume III. COAL Injury experience of the coal mining industry was improved in 1964, as measured by the declines of 1 and 14 percent, respectively, in the frequency and severity rates. Although the total number of injuries increased in 1964, a slightly greater proportional increase in man-hours worked caused the frequency rate to drop to 44.65 per million man-hours. The injury-severity rate in 1964 was 7,832 days lost per million man-hours of exposure. Employment and injury data for 1964 are based on final data for anthracite mines and preliminary data for bituminous coal and lignite mines. Fatality experience improved significantly with a record low number of 240 deaths in 1964. This total was 44 less than in 1963. The Nation's coal mines during 1964 were free of major disasters (a single accident resulting in the death of five men or more) for the first time since 1956. The

Jan 1, 1965

By J. E. Pahlman

Spontaneous oxidation and combustion of sulfides and resultant fires are serious problems in underground mines. The Bureau of Mines has con-ducted fundamental thermal gravimetric analysis (TGA) research to deter-mine the mechanisms and factors governing the rate of low-temperature pyrite oxidation, and to identify possible inhibitors to spontaneous oxidation and combustion. The mechanism of low-temperature pyrite oxidation was found to be topochemical, meaning that the oxidation process is controlled by the chemical reaction at the interface between pyrite (FeS2) and iron sulfate (FeS04)' An activation energy of 8.9 kcal/mol FeS2 was obtained for oxidation of minus 500-mesh pyrite in an atmosphere of 60 vol pct water vapor and 40 vol pct . Water-vapor content of the atmosphere was found to be the critical factor in the rate of spontaneous oxidation of pyrite, with a water-vapor content greater than 20 vol pct needed for accelerated oxidation. An atmosphere of pure oxygen resulted in negligible oxidation. The rate of pyrite oxidation is also greatly affected by the particle size of pyrite. Pyrite-oxidation rate increased drastically for particles less than 40 ~m. Room-temperature pyrophoric behavior was observed for freshly ground unoxidized pyrite (55 pct minus 5 ~m) upon exposure to air. Addition of water-adsorbing materials such as activated alumina (Alz03) decreased the rate of pyrite oxidation.

Jan 1, 1986

By C. C. Furnas

Despite the fact that a great many industrial processes depend on efficient contact between a gas stream and a bed of broken solids for their operation, the data in the literature are very meager. Several investigations3 have been undertaken, but the work has been limited in scope and application. BUREAU OF MINES PROGRAM OF RESEARCH For the past 10 years the United States Bureau of Mines has been engaged in research with the object of formulating a more or less complete quantitative theory of the workings of the iron blast furnace. Obviously, in order to do this one of the essentials is to have considerable definite information on the laws of gas flow through beds of broken solids. This report in a brief summary of the experimental work on the problem which has been done at the North Central Experiment Station. The complete report with more detailed tabulation of the data and explanations of the experimental procedure is in process of publication in the form of a bulletin.

Jan 1, 1928

By E. R. Palowitch

A centrifugal float-and-sink test procedure has been developed by the Bureau of Mines to reduce the time for the gravimetric separation of coals finer than l4-mesh from as long as 24 hours to less than 1 hour. Comparative tests indicated that centrifuging a minus 14-mesh Pittsburgh-bed coal for 20 minutes at 1,500 revolutions per minute produced results that compared favorably with static float-and-sink test results. Standard deviations of the mean recovery and ash content of the float obtained centrifugally ranged from 1.31 and 0.04 percent, respectively, at 1.30 specific gravity to 0.21 and 0.05 percent, respectively, at 1.60 specific gravity. As in static separations, retreatment of the products separated at low specific gravities was required.

Jan 1, 1961

By Oliver Bowles, J. E. Crawshow

A line of cordeau detonating fuse was placed in hole No. 2, no electric detonators being used in the hole. After 12 or 13 cases of 40 per cent nitro starch powder had been poured into the hole in loose form, it was found that a space of only 17 ft. remained for stemming. It was decided that space for an additional case of powder might be obtained by tamping the charge. The tamping was done with a heavy plunger, about 3 or 3 inches in diameter and 10 inches long, made of lead with an iron core with an iron eye in the top to which a 3/4 inch rope was attached, and weighing between 30 and 40 pounds. This weight was intended for use in sinking explosive in wet holes, and not for tamping. It is estimated that the tamping had continued at least 10 The quarry superintendent had gone a considerable distance for a box of powder, returned, and reached a point about 10 feet from the hole, minutes.

May 1, 1920

By S. H. Ash

A CLAY, sand, and gravel deposit known as the "buried valley" of the Susquehanna River is situated in the Northern field of the anthracite region of Pennsylvania near Wilkes-Barre. The presence of this buried valley and the uncertainty regarding the extent and physical condition of the water-bearing valley-fill deposits have made great care necessary in mining operations to avoid breaking the strata between the mine workings and the valley-fill deposits to the extent that inundation of the mine workings would follow. The principal factor that threatens to cut short the life of the anthracite industry, to curtail production, and to affect the economic structure of the people and business dependent on anthracite for their livelihood is inundation of anthracite mines (6,7).3

Jan 1, 1950

By Robert S. Sanford

Intensive investigations of domestic manganese deposits were conducted by the Bureau of Mines and the Geological Survey during the earlier part of the war minerals investigations when there was doubt that the quantity of manganese needed to produce the greatly increased tonnage of steel demanded for war supplies could' to obtained from its customary sources. Domestic deposits of ores that contain sufficient manganese for direct production of ferromanganese essential in steel Manufacture are generally small, and the bulk of the supply is imported. One of the few large deposits of low-grade manganese ore known in the United States is in the Artillery Peale district in southern Mohave County, Ariz. Manganiforous sediments underlie a very large area. Several large groups of claims, covering the most of the manganese-bearing ground, wore assembled in 1929 and 1930. The greater part of this area was leased by the M. A. Hanna Co. in 1937. Investigations by engineers and geologists for this company revealed that the average content of manganese is very low; but that the Maggio Canyon area, about 180 acres, contains higher-grade material. The company put down 28 vertical diamond-drill holds to explore this ground, under the direction of B. N. Wobbor, geologist.

Jan 1, 1948

By Edward P. Barrett

[Iron oxides, when reduced at temperatures below 900° form a dark gray substance, very porous bait otherwise in almost the same form as the original particles. In the temperature ire range of 1,000 to 1,100° the product is pertly sintered but still shows the outlines of the original particles. Those products are known as "sponge iron." At temperatures of 1,100 to 1,2000 the metallic iron begins to flow together and to a semifused, pasty, porous mass called a "bloom," which can he worked under a hammer to form a product similar to wrought iron; it contains slag inclusions and is too low in carbon to make steel. If the temperature is 1,300 to 1,300°, part of the iron will fuse enough to absorb more carbon. The dissolved carbon lowers the melting point and still more carbon is absorbed. The melted portion acts a flux for the unmelted metallic particles until the entire mass becomes a high-carbon fluid known as "cast iron." Sponge iron was probably the form in which the first iron was recovered from the ores. As early as the eighth century the Catlan forge3 developed into a low-shaft furnace known as the "high bloomary," in which iron eras produced in the form of a pasty mass. In 1340 the first blast furnace was built in Belgium. The greater part of the iron was made into wrought-iron blooms by crude puddling processes. Charcoal was used as the fuel until tie latter part of the 17th century when coke was used in England. In 1865 Bessemer built his first converter in. England, and within a few years the Siemen's regenerative open-hearth furnace was developed, also in England. Enormous expansion in the metallurgy of iron followed. The idea of "direct processes" for the production of iron arid steel has persisted throughout all this time. The production of steel from sponge iron has theoretical advantages over the present-day standard methods, and handreds of so--called "direct processes" have been proposed or tried during the past century.4]

Jan 1, 1929

By R. F. Abernethy

A modified Unterzaucher method was applied to the direct determination of oxygen in coal. Coal samples were pyrolyzed in a nitrogen atmosphere, and the gaseous oxygen compounds liberated were converted to carbon monoxide by a platinized-carbon catalyst at 9000 C. After passing over heated copper and through a tube containing soda-asbestos and magnesium perchlorate, the purified carbon monoxide was oxidized to carbon dioxide by iodine pentoxide--liberating an equivalent amount of iodine. The iodine was titrated with 0.02 ~ sodium thiosulfate; in a few tests the weight of carbon dioxide produced was determined. Direct oxygen determinations of coal included organic oxygen from the coal substance, plus a small quantity of inorganic oxygen derived principally from carbonate minerals and from combined water of silicates in the mineral matter. The influence of mineral matter on the direct oxygen determination was investigated by testing (1) untreated coal, (2) demineralized coal from which most of the mineral matter except pyrite was removed by treatment with hydrofluoric and hydrochloric acids, and (3) coal samples treated with dilute hydrochloric acid.

Jan 1, 1966

By D. F. Reed

As a part of a comprehensive survey of the Adirondack region, the Bureau of Mines, 1944 and 1945, conducted investigation of magnetic deposits at Dennemora, Russia Station, Redford-Clayburg, Standish, and the Ausable river region. Later in 1945, the Federal Geological Survey, started an aeromagnetic survey of the area and completed it in .1946. The Bureau of Mines extended its magnetic surveys in 1946 in the Redford-Clayburg area. In 1947 the Bureau of Mines .diamond-drilled throe holes in the Redford-Clayburg district. Clinton County has one active magnetite mine at Lyon Mountain and inactive mines at Palmer Hill and Arnold Hill, as well as along the Saranac River.

Jan 1, 1949

By R. Hogg, T. F. Dumm

"A procedure for evaluating the size/specific gravity distribution of ultrafine coal and the distributions of sulfur and ash with respect to particle size and specific gravity is described. The procedure is essentially an extension of the conventional coal washability technique in which special precautions are taken to ensure particle dispersion in the heavy organic liquids, centrifuges are used to obtain adequate separation rates, and micromesh sieves are used for size separation at fine sizes. An example of the application of this technique to the evaluation of the extent of liberation of sulfur and ash in a coal sample ground to 90Z passing 200 mesh (74 um) is described.INTRODUCTIONIn order to determine the potential for deep cleaning of coal by fine grinding to liberate sulfur and ash-forming minerals, it is necessary to obtain data on the distributions of these species by size and specific gravity. In conventional coal processing operations, this information is obtained by means of a standard ""washability"" analysis. Attempts to extend this procedure to ultrafine coal, however, have generally been unsatisfactory and have often led to unreliable and inconsistent results [11. The present authors have described a modified washability procedure in which cumulative specific gravity fractionation is combined with sub-sieve size analysis (by laser diffraction/light scattering) to determine the particle size/specific gravity distribution of ultrafine coal [2]. Unfortunately, because this technique does not involve separation of the individual fractions, only limited information can be obtained on the specific distributions of sulfur and ash.The objective of the work described in this paper was to develop and evaluate a procedure for size and specific gravity fractionation of ultrafine coal and to use conventional analyses for sulfur and ash to determine their relative distribution in the coal. The procedure is essentially a simple extension of the standard washability analysis [3] but incorporating special precautions for treating ultrafine particles.EXPERIMENTAL Material The material used in the development and evaluation of the ultrafine coal fractionation procedure was a medium volatile bituminous coal from the Lower Kittanning seam. A sample of the coal (nominally - 1/4 inch), obtained from the Penn State Coal Data Base, was ground to 90% passing 200 mesh by the following two-stage grinding procedure: About 2 kg of the as-received coal were ground to about 30Z passing 200 mesh in a Model 4-E Quakertown mill (""coffee grinder""). About 1 kg of this product was then ground to about 90Z passing 200 mesh in a Holmes Model 300 Pulverizer."

Jan 1, 1989

By R. L. Crosby

From studies of wrought magnesium alloys containing rare-earth elements, data are presented on the mechanical properties of the alloys at room temperature and at temperatures of 100°, 200°, and 300° C. Results of studies of the solid-solubility of cerium and zirconium in magnesium as determined by electrical resistance measurements are also discussed and are compared with those of other investigators. The strength of magnesium-cerium alloys did not increase with the addition of vanadium and titanium dioxide. The addition of zirconium increased the tensile strength of the alloys as much as 10,000 p.s.i. at room temperature, but this increase diminished above 100° C.

Jan 1, 1962

By S. E. Burton

The White Rock area of the Boiling Springs manganese-iron deposits comprises about 3,200 acres of land in Monroe Township, Cumberland County, Pa. (See fig. 1.) This property was brought to the: attention of the Bureau of Mines by Pennsylvania Geological Survey Bulletin 128, entitled "Manganese Ores of Pennsylvania" by R. M. Foose. It was examined by an engineer of the Bureau of Mines in August 1942 and was further investigated by the Bureau by churn drilling and underground development during the period December 1942 to February 1944. Beneficiation tests were made on samples of the ore. This report describes the work done during the investigation and presents the results obtained.

Jan 1, 1949

By R. F. Droullard

The Bureau of Mines has used gross alpha and gross beta detectors to continuously measure radiation working levels for a number of years. During this time, improvements have been made in the design and performance of continuous working-level (CWL) detectors. This report discusses the improved designs and some of the operating principles and applications of CWL detectors in the measurement of radon daughter products in mines and dwellings.

Jan 1, 1985

By Rethel L. Hubbard

Fourteen straight-run asphalts were prepared in the laboratory from bitumens obtained from three sources: (1) native bitumen from Rozel Point, Utah, (2). bitumen extracted from Athabaska bituminous sandstone at Canada, and (3) bitumen extracted from Edna bituminous sandstone outcropping in San Luis Obispo County, to seven asphalts with penetrations ranging from 19 to 287 at 77 F. were prepared from each of the bitumens. The yields of the prepared asphalts ranged from 74.5 percent for a 27-penetration asphalt from the Athabaska bitumen to 99.5 percent for a 271-penetration asphalt from the Rozel Point bitumen.

Jan 1, 1949

By Henry P. Chandler

THE year 1950 was one of increased activity in almost all branches of the abrasives industry, with nearly all abrasive materials showing a marked increase in tonnage and value. New records were made In the production of tripoli, ground sand and sandstone, pumice and pumicite, and garnet. Total production of crude artificial abrasives in the United States and Canada increased 17 percent in tonnage and 30 percent in value. Imports of industrial diamonds increased 100 percent in total value and 72 percent by weight, the 1950 importation being the largest since 1944. Imports of corundum increased 76 percent in tonnage and 4 percent in value.

Jan 1, 1953

By H. S. Caldwell

A magnesium-base incendiary alloy, containing about 20 percent cadmium, 4 percent aluminum, and 0.5 percent zinc, was investigated in a series of vacuum-distillation experiments to determine the feasibility of recovering magnesium and cadmium as refined metals. Alloys prepared in the laboratory and actual bomb-casing alloy were studied at temperatures of 550° to 750° C. and pressures of 100 to 150 microns. Simple distillation and fractional distillation methods were only partly effective in separating the cadmium and magnesium. They were separated satisfactorily, however, with a special vapor baffle designed to condense the metals selectively. Magnesium and cadmium products were 99 percent pure and together comprised 82 percent of the total condensate. About 17 percent of the condensate was intermediate-grade alloy that could be recycled with new charge and contained about 70 percent magnesium and 30 percent cadmium.

Jan 1, 1959