Search Documents

By Harold M. Smith

The production of oil during the early development of new oil fields is usually accompanied by large quantities of natural gas. Since In most fields gas under pressure is the main source of the energy causing the oil to move throug the sands into the wells and thence to the surface, this coincident production of natural gas will contime as long as present day producing methods are used. Generally the use of this gas is restricted, and markets are not readily available Consequently, a large portion of the gas produced at such times is often wasted by being blown into the air.

Dec 1, 1930

By G. St John Perrott

"The United States Bureau of Mines is cooperating with the State of Utah and the City of Salt Lake in an investigation of methods of abating the smoke nuisance in Salt Lake City. In the course of this work samples of the atmosphere have been collected and analyzed in an attempt to determine the part played by sulphur dioxide or smelter gases in polluting the air at Salt Lake City.A fairly wide-spread opinion exists in Salt Lake City that the smelters contribute appreciably to the smoke nuisance. The gases discharged from the smelter stacks are believed (1) to float over the city in a heavy blanket which prevents the smoke from rising, and (2) to unite with the water vapor in the air to form corrosive fogs injurious to health and property.The first of these theories seems untenable. If the gas did not mix with air it would sink, owing to its heavier specific gravity, and form a blanket an the earth. Actually, the gas diffuses rapidly in air and any part reaching Salt Take must he thoroughly diluted. Perhaps sulphur dioxide in sufficient concentration might aid in fog formation. The more obvious nuisance, however, would be the injury to health and vegetation.The Garfield smelter is 16 miles west of the city, The Murray smelter 8 miles south, and the Midvale smelter 12 miles south. Under normal operating conditions, a relatively small amount of solid matter is discharged from these stacks. The toxic gaseous constituent of the discharge is sulphur dioxide, it is being discharged from the smelters the year round. If they are a factor in the city's smoke problem, the concentration of this gas in the air of the city should be appreciable and should increase toward the smelters, the con centration being highest with a south or a west wind."

May 1, 1920

By Donald R. Corson

The Bureau of Mines is conducting research on the effects of various established and potential soil-stabilization additives to hydraulic backfill. This initial phase is an evaluation of the effect of inclusion of varying amounts of Portland cement and combinations of cement and a dispersant on the bearing strength of backfill. Results of unconfined compression tests are given for over 200 sample cylinders incorporating a fill material with cement or cement and dispersant. Inclusion of a minor amount of dispersant (0.2 percent by weight) is found to yield a significant increase in strength for 20-to-1 and leaner sand-cement mixes. An apparent optimum concentration of dispersant exists beyond which no further increase in strength is achieved. A dispersant-cement ratio of l.8- to-1 yielded a strength increase of 515 percent over the strength of untreated 40-to-l sand-cement mixes.

Jan 1, 1966

By G. Hakes

A data bank on bolter technology was assembled which included state-of-the-art industrial equipment as well as new equipment currently under development for the U.S. Bureau of Mines. This information was augmented by field visits to selected USBM contractors, mine operators and others for the purpose of obtaining a thorough understanding of present coal mine roof bolting safety and productivity problems. These direct contacts provided valuable insight regarding requirements for new bolting equipment necessary to assure wide user acceptance. Using this background material and information, a series of roof bolter concepts was developed offering improved operator safety with minimum impact on productivity. The concepts developed utilize existing componentry and technology wherever possible. All of the concepts feature a fully protected operator station located 6' to 10' outby the active bolt line and the hazardous rotating machinery.

Jan 1, 1978

By Spangler Ricker, F. T. Johnson

"SUMMARYThe Ione-Carbondale clays area is 2 miles northwesterly of Ione, Amador County, Calif. It was explored during the war by the Bureau of Mines to obtain data on the alumina content and to recover representative samples for beneficiation tests for alumina recovery.Seventy holes, aggregating 8,837 feet, were drilled, and about 10.3 acres of land was cleared of underbrush. Maps and cross sections were compiled showing location of holes, analyses, and other pertinent data.The clay beds vary in thickness from 13 to 196 feet, and are covered by a loose overburden, averaging about 11.9 feet in thickness. The ratio of overburden to clay is 1 : 8.2. Analysis of a composite sample showed the recoverable alumina (A12O3) and Fe2O3 content to be in the order of 23.6 percent and 2.8 percent, respectively.Topography of the clay area is ideal for open-pit mining methods and plant site.INTRODUCTIONInvestigation of alumina-rich clays for the possible production of aluminum was made during the recent war period, when the shortage of bauxite was becoming critical.Results of field examinations by the Bureau of Mines and the Federal Geological Survey indicated that one of the most promising areas for the development of alumina-rich clays is in the Ione-Carbondale district."

Mar 1, 1948

By Frank G. Miller

Controlling natural-water drives to effect efficient and economic production of petroleum, through wells, from reservoir sands and rocks is a problem of major importance in the oil-producing industry. Water-drive fields are characterized by large quantities of mobile water under high pressure immediately below the oil in the flanks or extraneous parts of reservoir formations. Hence, the water, which is in fluid connection with the oil and a source of a large proportion of the energy available for moving it, advances up-structure to replace it. This phenomenon of water moving crestward into the oil-bearing parts of the reservoir and replacing oil is termed edgewater encroachment. The mechanism by which oil is flushed out and continually replaced by water as the hydrocarbon content of the field is depleted must be understood if natural-water drives arc to be used successfully to, induce efficient recovery of oil from its reservoir rocks. Until recently, the function of water in the production of oil has been somewhat obscure and was not given the consideration it deserved in early petroleum production-research programs because of the greater importance associated with and the effort devoted to investigations concerning the relations of natural gas to production of oil. Thus, with virtually no fundamental information at hand, it is not surprising that at first edgewater was considered a necessary evil, and the manner in which it was dealt with depended largely on the experience of the operators. During the intervening years, however, .practical information on encroachment of edgewater in oil sands has been widely disseminated as a result of studies of oil-field depletion, and many theories pertaining to petroleum-reservoir energy and performance have been advanced; these theories necessarily included consideration of edgewater as an integral part of the reservoir fluids and a source of energy for propelling hydrocarbon fluids through the reservoir and to the surface of the ground.

Jan 1, 1941

By Alfred Wild

The Kraftile Co. plant, Fremont, Alameda County, Calif.--the largest producer of glazed, structural wall units west of the Rocky Mountains-- maintains modern processing facilities to evaluate and blend a wide variety of clays from several sources to produce quality products. The report desribes the prospecting, exploration, and test methods used to locate raw material sources and covers processing methods, cost factors, and trends. Also, the geologic and ceramic factors are considered in a general discussion of the economics, potentials, and requirements of clays as raw materials for ceramic tile manufacturing.

Jan 1, 1963

By Alfred Wild

The Kraftile Co. plant, Fremont, Alameda County, Calif.--the largest producer of glazed, structural wall units west of the Rocky Mountains--maintains modern processing facilities to evaluate and blend a wide variety of clays from several sources to produce quality products. The report desribes the prospecting, exploration, and test methods used to locate raw material sources and covers processing methods, cost factors, and trends. Also, the geologic and ceramic factors are considered in a general discussion of the economics, potentials, and requirements of clays as raw materials for ceramic tile manufacturing.

Jan 1, 1963

By Ronald M. Van Noy

A reconnaissance study of kyanite-group mineral deposits in the Northwest has revealed large exploitable reserves of the mullite-forming raw materials in the Woodrat Mountain and Goat Mountain districts of north-central Idaho. Potential coproducts or byproducts are garnet and muscovite mica. The Woodrat Mountain district contains garnet-kyanite-mica schist, which has been traced for 6 miles and may extend farther. Surface samples average 29 percent kyanite and contain up to 15 percent garnet. Inferred reserves of strippable ore with a low waste-to-ore ratio, and containing more than 15 percent kyanite, are more than 3 billion short tons. The Goat Mountain district contains several kyanite-mineral zones. Samples of the richest zones average from 10 to 20 percent kyanite minerals and represent about 200 million short tons of strippable rock. Beneficiation tests indicate that the kyanite minerals and garnet can be concentrated by a combination of gravity, flotation, and electromagnetic methods. Reserves in these deposits are sufficient to satisfy any foreseeable domestic and export demand. However, the freight tariff to reach the nearest major users of kyanite (located in the Midwest) has discouraged development of western kyanite resources. Western demand of a magnitude to support a moderate to large milling operation has not yet been developed. However, there is some foreign market potential. If a garnet byproduct could be prepared and sold for coated abrasive products or as grinding grains, an offset possibly could be gained to a por¬tion of the mining and milling costs for the Pacific Northwest producer. Such byproduct values would offer a means for expanding the geographic market areas as well as the regional market potential.

Jan 1, 1970

By Frank J. Wiebelt

The Carbonate King zinc mine is on the west slope of Kokoweef Peak, Ivanpah Mountains, San Bernardino County, Calif. It has produced more-than 10,000 tons of ore with a 39-percent?zinc content since mining operations began in 1940. The ore, consisting principally of calamine and smithsonite, occurs in replacements of the YellowPine limestone. Milling, has been done from the surface to a depth of 275 feet. Eight holes, aggregating 2,121, feet were drilled by the Bureau of Mines in an endeavor to establish extensions of the worked-out ore bodies and to develop new ones. Although indication of mineralization was found in several of the holes, no new ore bodies were developed.

Jan 1, 1949

By Mark I. Copeland

Bureau of Mines researchers investigated the combined effect of copper and tin additions on the mechanical properties of hot-rolled steels. Wrought steels containing 0.2 wt-pct C and up to 0.2 and 1.0 wt-pct Sn and Cu, respectively, were made and evaluated by conducting tensile and impact tests and electron-beam microprobe and electron microscopy examination. Tin additions did not significantly affect the tensile properties of steel at different copper contents in the hot-rolled condition. Tin lowered the copper content at which strengthening by copper precipitation normally starts, 0.8 wt-pct, and decreased the strength of steel aged at 1,022° F (550° C). The most adverse effect of tin was lowering the notch toughness of steels at most copper contents.

Jan 1, 1976

By J. E. Conley

Available statistics show that the demands of the American chemical industry for sodium sulphate have been increasing slightly in recent years. The supply from domestic sources, particularly In the form of byproduct salt cake from the acid manufacturers, has been tending to decrease due to the growing manufacture of synthetic acid. Both hydrochloric and nitric acids are being synthesized from their elements. The natural result has been that a smaller amount of salt cake is available. Simultaneously, the expansion of the Kraft paper industry, especially in the South, has brought about greater demand for sodium sulphate in that section. This dean is being met by domestic byproduct salt cake, by imported German sodium sulphate made from potash waste liquors, and by favorable situated domestic deposits of Glauber salts and tile anhydrous salt, thenardite. No shortage of natural sodium sulphate exists in the United States, but usually such deposits occur in semiarid regions far removed from transportation facilities and from markets. Moreover, the major portion of the natural deposits is Glauber salt or mirabilite (Na2SO4 ? 10H20), which must be dried or dehydrated in order to meet consumer requirements. The water of hydration represents, roughly, 55 percent of tae total weight of the crude salts and therefore has a very important influence on transportation costs. In marry instances the cost of getting, even the dehydrated product to market is the deciding economic factor. Therefore, the recovery oil production of anhydrous sodium sulphate from plant-.waste liquors or from natural brines of suitable composition might be economically feasible. The U.S. Bureau of Mines, at its nonmetallic Minerals Experiment Station, New Brunswick, N. J., has, for a number of rears, been investigating the commercial possibilities of treating the complex saline mineral polyhalite (K2SO4?NgSO4?2CaSO4?2H20) for the recovery of potash and magnesia. Certain proposed processes (1, 2, 3, 4)4/ yield waste liquors that contain the bulk of the magnesium and sulphate originally combined as magnesium sulphate in the polyhalite molecule. Sodium chloride In limited concentrations is also present, as extensive beds of salt occur in strata overlying the polyhalite deposits. A typical waste liquor would contain:

Jan 1, 1936

By Stephenson. E. L.

"INTRODUCTION In the spring of 1942 a series of magnetometer surveys on deposits of black sand underlying Pleistocene raised marine terraces along the coast of southwestern Oregon was nada by the Division of Geophysical Exploration of the Federal Bureau of Mines in cooperation with the Oregon Department of Geology and Mineral Industries. A few preliminary tests had been made in the same area in May 1940 and December 1941.The sands contain fine gold and metals of the platinum group, and, beginning in 1852, extensive, but spasmodic mining and exploration have been done for these precious metals. There are many old placer, mines and prospects, although for the most part the yield of the metals has been small. The sands also contain other minerals of potential value, including ilmenite, magnetite, garnet, zircon, and particularly chromite, and the wartime demand for domestic chromite resulted in extensive testing and development of the known deposits. The purpose of the magnetometer surveys was to determine the efficacy of, magnetic methods in tracing and outlining these known deposits and in prospecting for new ones. The field work was done between March 17 and May 29, 1942, by the author assisted by W.W. Paulsen of the Oregon Department of Geology and Mineral Industries."

Jun 1, 1945

By Charles W. Huggins

DEVELOPMENT of the electron microscope has permitted man to examine many small objects that could not be resolved by the light micro-scope. Diffraction, spherical aberration, and chromatic aberration are the main factors that limit resolution to about two-tenths micron with the light microscope. No matter how perfectly a light microscope is constructed and operated, it cannot possibly resolve points separated by less than two-tenths micron. Rapid development following World War II has produced many electron microscopes capable of 20 A resolution. Fibrous inorganic minerals are well suited for electron microscopic study. Many micrographs of chrysotile have been published, but electron microscopic study of the amphiboles has been somewhat neglected. New techniques in sample preparation have simplified the study of fibrous material. Ultrasonic energy has been very helpful in sample dispersion. This publication contains a representative group of electron micrographs of natural inorganic fibers that have industrial value. These fibers commonly are referred to as the asbestiform minerals. The Bureau hopes that the knowledge gained through electron microscopy and other scientific study of the natural inorganic crystalline fibers eventually will lead to the production of synthetic fibers that will satisfy the requirements of industry.

Jan 1, 1959

By G. R. Hopkins

[Apparent progress in economy at petroleum refineries, as measured by the average amount of hest units required to refine a barrel or crude oil, received a set-back in 1938, when the average rose to 567,000 B. t. u., compared with 562,000 B. t. u. in 1937 (see fig. 1). The primary factor in the rise in average heat requirement's per barrel of crude oil refined in 1938 was the decline in total runs to Invariably the average requirement increases when crude inn to stills decline, and vice versa. In other words, annual gains in fuel efficiency at refineries are masked by the degree to which the capacity is utilized. Additional crude runs give lower average heat requirements in two grays first, because they are mane with the expenditure of cc-comparatively small amounts s of auxiliary heat, and, second, because additional runs generally represent simple topping operations. In 1938 crude runs to stills declined 1.6 percent (from 1,183,440,000 barrels in 1937 to 1,165,015,000 barrels in 1938), but the total heat consumption declined only 0.4 percent, or from. 663,866 billion B. t. u. in 1777 to 660, 56 billion in 1938.]

Jan 1, 1939

By William C. Cooley

A technical and economic study was made of the feasibility of establishing an underground hydraulic coal mine in the Wilkeson-Carbonado coal field approximately 25 miles southeast of Tacoma, Washington. The deposit contains reserves of more than 200 million tons of generally high quality metallurgical coal. It is located in nine seams of minable thickness in a complex, folded and tectonically disturbed set of anticlines and synclines. Typical dip angles are up to 60°, with minable seam thicknesses of 6 to 17 feet. A mine plan was made for a 2 million TPY mine (clean) using two shafts to access the deposit to a depth of 2500 ft. The mining method uses monitor jets to break coal by sublevel retreat mining, fluming to a sump and pumping the minus 0.25 inch coal to the surface and to a preparation plant. The plus 0.25 inch coal is hoisted by skip. Cleaned met coal would be shipped by rail for export. A middlings product would be sold as thermal coal. Assuming a coal price of $48 per short ton (FOB the mine) for the met coal and $35 for the middlings, the return on investment is estimated at 20% after taxes. The many uncertainties about the geological conditions and the specific mine design parameters make the economic analysis and conclusions somewhat tentative. A second mine could also be developed in the eastern section of the reserves to produce 1 million TPY of clean coal and is expected to have similar economics. Recommendations are made for a Test Mine and a Pilot Mine leading to a production mine.

Jan 1, 1983

By John P. Harmon

A group of organic chemicals, known as wetting agents, has been developed, primarily for use in the textile industry. These chemicals have the property of reducing the surface tension of water when mixed with it in very dilute solutions. The advantage of lowered surface tension is recognized in dust-control work, and several wetting agents, have been tried by dust-control engineers with varying degrees of success. It is well-known that certain solids, coal for instance, are extremely hard to wet with plain water because of the high surface tension of water and the water-repellent action of coal. If the surface tension of the water is reduced, it can be demonstrated that the coal can be wetted easily. This is accomplished practical and at law cost by dissolving a very small percentage of wetting agent in the water that is to be used for wetting purposes. (Care should be exercised in using a wetting agent to be sure that it will not interfere with a subsequent process.) For some time, the comparative efficiency of various wetting agents has been the subject of considerable work by dust-control men at coal mines, as well as by members of the Bureau of Mines 3/, 4/, 5/, 6/. In this connection, a number of samples of air-borne dust have been collected in the mines. With the exception of dust-control measures conditions of dust generation and dissemination were maintained as, nearly uniform as possible. Samples were collected when water alone was sprayed on the cutter bar of a mining machine; various wetting agents were then successively added to the water and more samples of air-borne dust were-collected.

Jan 1, 1946

By A. J. Kauffman Jr.

The Petrographic Section of the Bureau of Mines, Northwest Electrodevelopment Laboratory, Albany, Oreg., annually examines thousands of minerals and rocks. Samples are received from mining, engineers, prospectors, and government agencies, both State and Federal. During the past 2 years certain uncommon minerals have been identified in the samples submitted. Eleven occurrences have been selected for reporting in detail. These selections were made because in most cases a new locality is involved. The data reported are the result of application of the latest techniques, and widely disseminated references concerning each mineral have been added for completeness. Several occurrences have been described by other investigators; in those cases new data have been supplied to supplement the already published information on these occurrences. No uranium-bearing minerals have been included; they will be treated in another paper. The Bureau of Mines does not make chemical analyses or assays for individuals or firms In direct competition with private laboratories. Mineral¬ogical examinations, however, are made for prospectors and the general public. Such examinations a call surface to determine whether the sample in question has possible commercial value. If it has apparent value, the sender is so informed, and suggestions as to its .Arc, development and marketing are offered. The latest scientific apparatus is available to aid in identification. The apparatus includes microscopes, both wide-field and polarizing, a Bunsen-type spectroscope for visual observation of the Zinc and band spectra of many elements, differential thermal apparatus for the examination of hydrous material, apparatus for cutting and mounting either thin sections for study in transmitted or polished surfaces for reflected-light studies, and a high-intensity magnetic separator for concentrating minerals according to their magnetic susceptibility. Also, available, but not an integral part of the Section, are several laboratory-type Geiger counters, a grating spectrograph, and X-ray diffraction apparatus. If need be, all of these tools may be employed to identify a mineral or rock.

Jan 1, 1950

By S. D. Cramer

Corrosion research is being conducted by the Federal Bureau of Mines to determine suitable construction materials for geothermal resource recovery plants. As part of this research, the corrosion resistance of 31 iron-nickel-, aluminum-, copper-, titanium-, and molybdenum-base alloys was characterized and evaluated in laboratory corrosion studies in low-and high-salinity geobrines representative of those found in the Imperial Valley, Calif. General, crevice, pitting, weld, and stress corrosion were measured at 105° and 232° C in deaerated brines and brines containing dissolved 02, C02, and CH4 General corrosion rates in deaerated brines at 105° and 232° C were usually below 5 mpy for the alloys tested except carbon steel, the low-alloy steels, Monel 400, 70-30 cupronickel, and the aluminum-base alloys. Dissolving carbon dioxide and methane in the brines at 2320 did not markedly alter these results. However, the introduction of oxygen, which can enter the brine during process operations, seriously degraded the corrosion resistance of many alloys by increasing the incidence of stress corrosion cracking, crevice corrosion and, except for the titanium-base alloys, pitting. In deaerated brine at 2320 C, the general corrosion rates for carbon steel and the low-alloy steels were relatively unaffected by pH in the range of 6.1 to 3.0. However, general corrosion rates increased sharply below pH 3.0. In deaerated brine at 232° C, welds in several iron-, nickel-, and titanium-base alloys corroded at rates comparable to the general corrosion rates of the alloys, but the addition of oxygen to the brine increased corrosion rates for welds in Inconel 625 and E-Brite 26-1. Alloys exhibiting good corrosion resistance in the deaerated Salton Sea KGRA-type brine at 232° C were E-Brite 26-1, Inconel 625, Hastelloy S, Hastelloy G, Hastelloy C-276, TiCode-12, Ti-0.2Pd, Ti-2Ni, Ti-1.7W, and TZM. The alloys most resistant to corrosion in oxygenated Salton Sea KGRA-type brine at 232° C were the titanium-base alloys. These alloys appear the most suitable for use in the construction of geothermal resource recovery plants. Carbon steel and the low-alloy steels are unsatisfactory for high-temperature, high-salinity brines and alternative low-cost materials with improved corrosion resistance should be sought.

Jan 1, 1980

By Arnold B. Hubbard

This report describes a method of concentrating the insoluble organic material (kerogen) in a rich Colorado oil shale without any apparent alteration of its original chemical form. The method involved treating finely pulverized shale with dilute acetic acid at room temperature to remove the carbonates, which act as a cementing agent for the shale, and cause the shale particles to partly disintegrate into the organic and inorganic components. The acid-treated shale then was centrifuged in different liquid mediums ranging from 1.4 to 1.15 gravity to effect a mechanical separation. From a Colorado oil shale containing 48.0 percent ash, kerogen concentrates containing 43.3 to 8.7 percent ash were obtained. The carbon:hydrogen ratios of the kerogen in the original shale and the different concentrates were essentially the same. The oil:kerogen ratios calculated from Fischer assays of the above samples were essentially the same, regardless of the organic or inorganic contents. This was also true of the assay water:kerogen ratios of the same samples. These data indicate that no significant change occurred in the kerogen during the concentration process.

Jan 1, 1952