Search Documents

By R. E. Lindstrom, D. J. Bauer

Studies were conducted to assess the potential of naphthenic acid as a fractional extractant for rare- earth mixtures and yttrium in sulfate solution . Naphthenic acid was an effective extractant , and separation factors were favorable in the presence of aqueous phase chelating agents . Addition of EDTA to the naphthenic acid extraction system resulted in average separation factors of 2.2 between adjacent yttrium- group elements , whereas DTPA resulted in average separation factors of 3.5 between adjacent cerium- group elements . EDTA was of value in separating yttrium from the rare- earth elements . Thorium and uranium were preferentially extracted over the trivalent rare- earth elements by naphthenic acid .

Jan 1, 1964

By Robert L. Lagace

This final report documents the work done by Arthur D. Little, Inc. (ADL) on behalf of the U.S. Bureau of Mines, Pittsburgh Mining and Safety Research Center (PMSRC) , on Contract H0122026 (which began in August of 1971) . Under this contract ADL provided technical assistance to the Bureau on a task basis on virtually all aspects of the Bureau's programs related to present and planned emergency and operational communications and miner location systems for underground coal mines. The work consisted of in- dependent investigations, analyses, experiments, breadboard and prototype hardware development, workshops and technology transfer seminars on mine communications, and on-going evaluations and guidance related to the Bureau's contracted programs on electromagnetic noise, mine communications systems, and trapped miner location. This final report documents the work in two volumes, Volume I, "Emergency and Operational Mine Communications," and Volume II, "seismic Detection and, Location of Isolated Miners." The Tables of Contents of both Volumes are included in each Volume.

Jan 1, 1974

By Stephen E. Mosher, Suzanne D. Smith

Ground, air, and water vehicles can expose humans to substantial multi-axis vibration. Multiple input/multiple output relationships or models exist for estimating frequency response functions of linear systems1, 2. These relationships have been applied by some investigators to evaluate the effects of occupied seat vibration3, 4. Using a multiple input/single output model, this study investigated the effects of single- and combined-axis vibration in the fore-and-aft (X), lateral (Y), and vertical (Z) directions on vibration transmission to the human chest. Frequency response functions (transmissibilities) were estimated and compared for the back-on and back-off postures. Methods A rigid seat with seat back was mounted onto the Six Degree-of-Freedom Motion Simulator (SIXMODE). A flat acceleration vibration signal was generated between 2 and 40 Hz at 1.0 ms-2 rms in the single and combined X, Y, Z, XY, XZ, YZ, and XYZ axes. The signals were shifted in time so that the combined inputs were not fully correlated. Lightweight triaxial accelerometers were used to measure accelerations at the seat base (input) and at the bony manubrium of the chest (output). The maximum of nine frequency response functions (H(?)) or transmissibilities were estimated from the auto- and cross-spectra. The system transfer matrix for the XYZ inputs and chest Z output is [ ] where PxZ, PyZ, and PzZ are the cross-spectra between the three inputs at the seat base and the Z output at the chest, respectively, and Pxx, Pxy,…zz are the auto- and cross-spectra between the input signals (? not shown in Eq. 1). Equation 1 can be similarly written for the chest X and Y outputs. Matlab® was used to estimate the auto- and cross-spectral densities for calculating the transmissibilities, ordinary coherences (for single inputs), partial coherences, and multiple coherences. Results Figure 1 illustrates the major chest transmissibilities observed for the two postures. Vertical vibration showed a consistent influence on the chest X response (Chest X/Z), most likely causing chest pitch. Some chest Z responses were observed with X-axis inputs, but the results were variable and difficult to interpret. In general, other factors besides the known inputs did not affect the transmissibilities shown in Figure 1 (Repeated Measures ANOVA, P<0.05). This was

Jan 6, 2006

By W. T. Millar

Field reconnaissance and laboratory tests an clay from South Windsor, Hartford County, Conn., indicate that the clay is suitable for lightweight aggregate raw material. Exploration of the deposit supports the conclusion that the reserves of clay are sufficient for economical mining operations to produce lightweight aggregate. Preliminary tests indicated that the clay has a short bloating range. Initial expansion occurred at 2,000° F, and at 2,100° F the clay was slightly overfired and sticky. Rotary kiln tests verified the preliminary data, and these tests showed that the clay would make a good lightweight aggregate if the processing temperature and the kiln feed sizes were closely controlled. Lightweight concrete made from the processed aggregate had properties comparable to those of concrete made from a commercial clay aggregate.

Jan 1, 1964

By E. J. Kloos

This publication lists devices approved jointly by the Secretary of Interior and the Secretary of Health, Education, and Welfare, as of May 24, 1972, under provisions of Section 11.2, Part 11, Subchapter B of Chapter 1, Title 30, Code of Federal Regulations (37 F.R. 6244, March 25, 1972), for use in mines as respiratory protection in oxygen-deficient atmospheres, and in gases, vapors, dusts, fumes, and mists. Included are self-contained breathing apparatus, gas masks, and supplied-air, dust, fume, mist, and chemical-cartridge respirators. Names and addresses of manufacturers appear in the appendix.

Jan 1, 1972

By Almon F. Robertson

The floor of Shady Valley, Johnson County, Tenn., is underlain by the Shady dolomite formation. In places the residual clay derived from this formation contains considerable manganese oxides. Nine properties in Shady Valley and two in Doe Valley were prospected by the Bureau of Mines from January 1943 to April 1943. The results obtained indicate that the ore bodies are small and spotty and, that the ore is not well-adapted to gravity concentration. The work of the Bureau was confined to the open end of the valley. One mile northeast of the Ham Greer property, Beaverdam Creek enters a rocky gorge, and it was believed that the few prospects in this area were of secondary impor-tance and, owing to the steep slope and general roughness of the terrain, that exploration with the rite&apos;, bucket-drill would be impracticable. A total of 4,398.5 feet was drilled in 131 holes. In addition, 235 lineal feet of bulldozer trenches were cut and 4.5 feet of test pits were sunk. The following nine properties were explored in Shady Valley: Bentley, Walker, Blevins, Scott, North Ham Greer, South Ham Greer, Lipford, Blackburn, and Steagall In Doe Valley, the Gerd Shoun and Brookshire properties were explored.

Jan 1, 1949

By K. L. Cashdollar

A project to evaluate the South African bagged stone dust explosion barrier was successfully completed at the National Institute for Occupational Safety and Health (MOSH), Pittsburgh Research Laboratory&apos;s (PRL), Lake Lynn Experimental Mine (LLEM) during the period November 1999 through May 2000. The tests were conducted in a three- entry section of the LLEM. Two types of explosions were used to evaluate the distributed and concentrated bagged barrier performance in a multi-entry mine section. The fuel zone of the first explosion type was only in the center B-drift. In the second explosion type, coal and stone dust mixtures were place in all three drifts. A total of six explosions, including two baseline and four barrier evaluation explosions, were conducted. Of the four barrier explosions, the distributed and concentrated barriers were each evaluated against the two explosion types. For these explosion tests, the distributed barrier extended from about 74 to 170 m and the concentrated barrier from about 74 to 104 m in B-drift. The distributed barrier successfully stopped flame propagation in both types of explosion tests. The flame extended further for the explosion tests where the dust was loaded in all three entries compared with dust loaded only in the center entry% but in both cases the flame was stopped within the barrier zone. The concentrated barrier was also successful in stopping flame propagation m both explosion tests. From the full-scale experimental mine test results, it can be concluded that both bagged barrier designs were effective in stopping coal dust explosions in the multiple entries of the LLEM.

By Donald A. Voigt

This publication is intended as a guide for persons responsible for obtaining classifications and approvals Tor explosive compounds, mixtures, or devices from the U.S. Department of Transportation (DOT). It deals with the procedures for obtaining a recommendation for classification of an explosive compound, mixture, or device through the Bureau of Mines. Completion of the procedures detailed in this guide is necessary to obtain a final classification of an explosive compound, mixture, or device and assignment of an "EX" number by DOT, which will allow the producer to offer the explosive for shipment within the United States. This guide also gives procedures for obtaining United Nations (U.N.) classification for shipping outside the United States.

Jan 1, 1990

Provide optimum visibility of mining operations while maintaining protection and comfort for machine operators. Approach A cab with hydraulically powered variable-height control was developed and used on a loading machine in underground operations. How It Works The cab is attached to the vehicle on a horizontal trunnion located near the forward end of the cab. A hydraulic cylinder, controlled by the operator from inside the cab, pivots the cab about the trunnion providing variations of up to 16 inches in elevation. The nominal tramming position of the cab is with its underside 6 inches above the mine bottom. From this position the cab can be pivoted up, or down, so that its back end is elevated 10 inches, or lowered to the floor. (See Figure 1.) The cab encloses the operator for protection against both overhead and lateral obstructions, and it raises or lowers, allowing the operator to select the most advantageous cab height. The cab is angled inboard 30 degrees to the machine line of direction. The operator&apos;s seat swivels to allow view of the conveyor during loading. All controls are located within the cab and move up and down with it.

Jan 1, 1978

By Vladimir Adamek

This paper describes the Bureau of Mines development of a novel subsidence prediction methodology suitable to the mining and geologic conditions in the Northern Appalachian Coal Region. It describes the computation of vertical and horizontal movements, inclination, curvature, and horizontal strains. The substance of this method is the separation of the effects of lithology by introducing a correlation between hypothetically homogeneous overburden and existing lithologic conditions, while providing for different mining conditions, i.e., underground geometry and overburden thickness. The effects of lithology have been expressed in the form of a variable subsidence coefficient within the subsidence trough. The subsidence co-efficient is considered a constant for other predictive methods. Field data from 16 test sites at 11 Bureau longwall panel studies were used in the analysis. For each panel, the characteristics of the variability of the subsidence coefficient were defined. Regression analysis of the subsidence coefficients from all test sites on their locations relative to the edges of their respective panels yielded a third-degree polynomial equation. The results from additional longwall panel studies, not included in the regression analysis, were used to prove the validity of this method. To facilitate the use of this precalculatlon methodology, a computer program was written in BASIC for use on a personal computer.

Jan 1, 1987

By Manuel Gomez

Areal distributions for ash, total sulfur, and sulfur forms were developed for the top 12 inches, the middle section, the bottom 8 inches, and the total seam of Pittsburgh coal in southwestern Pennsylvania. The sulfur and ash exhibit an apparent high local variability. As a general rule, both the sulfur and ash show high concentrations in the top 12 inches and in the bottom 8 inches of the seam relative to the concentrations observed in the middle section of the seam. The high-low sulfur and ash concentrations in the top 12 inches of the seam are not coincident with the high-low sulfur and ash concentrations in either the middle section or the bottom 8 inches of the seam. With respect to sulfur and ash, it is suggested that the top and bottom sections of the Pittsburgh coal may reflect both a syngenetic and epigenetic origin. Present data support the belief that paleotopography controlled Pittsburgh seam deposition. Evidence is presented to show that channels were cut at various times into the semilithified sediments that buried the Pittsburgh seam. In this channeling process, portions of the Pittsburgh coal may have been eroded away. Following channel development, the lower part of the Pittsburgh sandstone filled the complex system of braided channels to produce the "want areas" encountered in present mining operations. In localized areas of the Pittsburgh seam, impingement of Pittsburgh sandstone may be responsible for the lateral displacement of the coal. Information of this type becomes important in the assessment of exploration data, in the development of a quality control system for mine output, and in mine life planning.

Jan 1, 1974

By John C. Machisak

INJURY EXPERIENCE AND EMPLOYMENT DATA on all stone quarries and associated plants in the United States are presented in this publication for the calendar year 1959. Such related operations as the manufacture of cement and lime and rock dressing are included. Data on clay and sand and gravel operations are not included and will be found in other Bureau publications on injuries and employment. The Bureau is authorized to make requests for such data and the information voluntarily submitted by the operators contributes to the promotion of safety in the quarrying industry. Every effort has been made to make this canvass as complete as possible. Data for production workers and office employees at the quarry site are included.

Jan 1, 1963

By Foster Fraas

The response of minerals in magnetic separators is in accordance to dynamic rather than static magnetic susceptibility values . The dynamic value varies with respect to both passage speed through the separating field and time of exposure in a preliminary treatment field . Tests on 16 minerals and solids have demonstrated that both of these factors affect different minerals in different ways .

Jan 1, 1964

By John C. Machisak

INJURY EXPERIENCE AND EMPLOYMENT DATA on all stone quarries and associated plants in the United States are presented in this publication for the calendar year 1959. Such related operations as the manufacture of cement and lime and rock dressing are included. Data on clay and sand and gravel operations are not included and will be found in other Bureau publications on injuries and employment. The Bureau is authorized to make requests for such data and the information voluntarily submitted by the operators contributes to the promotion of safety in the quarrying industry. Every effort has been made to make this canvass as complete as possible. Data for production workers and office employees at the quarry site are included.

Jan 1, 1963

By Laurence G. Trudell

Geology and oil-yield data are presented for a 58-square-mile area encompassing the U.S. Department of the Interior oil-shale leasing program tracts in the western Washakie Basin, Sweetwater County, Wyo. Lithology and oil yields of samples from three Bureau of Mines coreholes are evaluated and correlated with Kinney Rim surface sections measured and sampled by the U.S. Geological Survey. Minable sections of oil shale averaging up to 25 gallons of oil per ton crop out on Kinney Rim in the Laney Member of the Green River Formation. Thick oil-shale sections in the Laney Member that average 15 gallons per ton represent 155 million barrels of oil in place per square mile. In the lower part of the Green River Formation the Tipton Shale Member contains a 20-to 40-foot section averaging 15 gallons per ton. Beds of high-volatile C bituminous coal up to 6 feet thick are present in intertongued parts of the lower Green River Formation and upper Wasatch Formation.

Jan 1, 1973

By John C. Machisak

THIS INFORMATION CIRCULAR contains injury and employment data for all stone quarries in the United States for the Calendar year 1960. This publication contains statistical data on injuries and employment pertinent to the stone quarries and related operations, such as the manufacture of cement and lime, rock dressing etc., but excludes statistics for clay and sand and gravel operations. Data for these commodities may be found in other Bureau publications. Reports received from the operators are voluntary responses to the Bureau&apos;s request for information; therefore, the figures may not be complete for the industry. However, since these data contribute greatly to the promotion of safety, every effort has been made to make them representative of the industry.

Jan 1, 1963

By John C. Machisak

THIS INFORMATION CIRCULAR contains injury and employment data for all stone quarries in the United States for the Calendar year 1960. This publication contains statistical data on injuries and employment pertinent to the stone quarries and related operations, such as the manufacture of cement and lime, rock dressing etc., but excludes statistics for clay and sand and gravel operations. Data for these commodities may be found in other Bureau publications. Reports received from the operators are voluntary responses to the Bureau&apos;s request for information; therefore, the figures may not be complete for the industry. However, since these data contribute greatly to the promotion of safety, every effort has been made to make them representative of the industry.

Jan 1, 1963

By John H. Soule

The Royal John mine was examined in November 1942 by a mining engineer of the Bureau of Mines, who proposed development of the Royal John and other properties in the area. Geologists of the U. S. Geological Survey studied the area in 1943 and 1944 and made definite recommendations. Also, in 1943 the Peru Miring Co. mapped the Royal John and did considerable diamond drilling. The Bureau of Mines started the Royal John portion of a project pertaining to the general district in April 1944. This project was completed in Juno 1945. The work, consisting of diamond drilling, was supervised by Robert O. Hill, mining engineer, and the results were published in Report of investigations 3904, Exploration of Grey Eagle, Grandview and Royal John Claims, Grant County, N. WIC. In 1947 and 1948 the Royal John was re-examined by a Bureau engineer, and additional development to increase the reserves of low-grade lead-zinc ore was proposed. This project was started in August 1948 and completed in Juno 1949.

Jan 1, 1950

By R. P. Vinson

The Bureau of Mines evaluated two real-time light-scattering dust monitors by measuring their response to Pittsburgh Seam coal dust and Arizona road dust (ARD). Both monitors, the model PDS-l, a personal dust sensor, and the model PCD-l, a digital dust indicator, are made in Japan by Sibata Scientific Ltd. Tests were conducted inside a laboratory aerosol chamber designed to maintain a uniform spatial distribution of the test dust. PDS-l and PCD-l measurements of concentrations for each test dust were averaged over 4-h test periods and compared with simultaneous gravimetric measurements. Both dust monitors responded linearly with mass concentration with both coal dust and ARD. However, the linear response of the PDS-l differed from that of the PCD-l for both dusts.

Jan 1, 1987

By Oliver Bowles

Slate possesses many admirable qualities, not only as a roofing material, but for blackboards, electrical switch boards, and for various structural uses such as stair trends, floor tile, baseboards, and sanitary enclosures. The American slate industry was established manor years ago, and has made remarkable progress, particularly during the past five years. One of the chief drawbacks to more rapid expansion is the high percentage of waste which reaches 75 to 94 per cent of gross production. Much of this waste is duo to rock imperfections over which man has no control, but a careful study of tae industry by the Bureau of Mines over a period of years indicates that an undesirably large percentage of the marketable slate is wasted in the processes of quarrying and manufacture. The initial step in quarrying slate is to separate from the solid ledge masses of a size that ray be conveniently removed from the quarry. This first step entails a greater waste of material than any subsequent process, and, therefore, invites the most earnest effort toward waste reduction. Attention has consequently been directed toward possible improvements in methods of making primary cuts in the quarry floor. A study of European practice with the wire saw, together with theoretical consideration of its advantages, convinced the writer that it possessed sufficient merit to justify its use as a primary slate cutter in American quarries. No practical conclusion in this matter could be reached except by experiment. Therefore, the desirability of obtaining equipment and trying it out under actual conditions of operation was urged upon operators. While no doubt the equipment could be readily manufactured in America, it had already been developed to the point of practical use in Europe; therefore the writer urged the desirability of purchasing one completely equipped wire saw in Europe, and determining through tests whether it gave sufficient promise of success to warrant its manufacture in America.

Jan 1, 1927