Search Documents

By Robert C. Dyni

The Bureau of Mines in cooperation with the Solution Mining Research Institute conducted surface and subsurface investigations over five solution-mined salt cavities in the Hutchinson, KS, area. The purpose of these investigations was to determine the mechanisms that lead to the formation of sinkholes above collapsed solution cavities. Of the five salt-solution cavities investigated, four had collapsed and produced sinkholes prior to the time of the investigations; the fifth cavity was considered stable. Exploratory drilling and coring operations were conducted at all five sites; surface stability monitoring was conducted at three of them. The results of these studies indicate that excessive dissolution at the salt-shale contact of each collapsed cavity produced large, unsupported roof spans that ultimately exceeded the structural integrity of the overburden. The stable cavity was not exposed to excessive dissolution at the salt-shale contact; this limited the roof span and ensured a stable cavity. The data also show that surface settlement in the vicinity of the two surface-monitored sinkholes continued for approximately 7 years after the sinkholes formed, indicating that the rubble piles of the collapsed cavities were undergoing gradual consolidation.

Jan 1, 1986

By R. Hogg

"The basic population balance models for agglomeration processes are reviewed and procedures are described for extending their applicability to systems with size-dependent rate constants and to the formation and growth of porous agglomerates from rigid, solid-particles. Simplified procedures for the further extension of the models to include simultaneous agglomerate growth and breakage are also described.INTRODUCTION The association of small particles into clusters or agglomerates is a significant factor in many facets of particle processing. Agglomeration processes are widely used to facilitate handling, storage and utilization of fine powders. Processes such as coagulation or flocculation are used to aid solid-fluid separation in dispersed particulate systems. Agglomeration also occurs as an accompaniment, often unwanted, to other particulate processing operations such as fine grinding, mixing and blending, transport and flow.Reliable agglomeration models are needed for improved understanding of the processes in general and of the complex role of numerous, interacting variables as well as for direct application to the design and control of industrial processes such as flocculation, granulation and pelletization. Ideally, the models should account for the primary forces responsible for agglomerate formation and growth, the effects of external forces on process dynamics, the development of agglomerate structure and its role in the process itself, and the effects of concurrent processes such as structure modification (e.g. compaction) and agglomerate breakage or degradation."

Jan 1, 1989

By G. W. Jones, F. E. Scott

"INTRODUCTION During the last war, considerable attention was given to the search for materials or combinations of materials for use as expelling agents for aerosols in the well-known ""aerosol bomb."" These materials must be free of fire and explosion hazards under normal conditions of use.In cooperation with the Department of Agriculture and other Federal agencies interested in the work, the Bureau of Mines carried out a laboratory investigation on the inflammability of- dimethyl ether-dichlorodifluoromethane air mixtures. 4/The method of investigation was essentially the same as that used in a similar investigation dealing with the inflammability of propane-butane-dichlorodifluoromethane mixtures. 4/SOURCE OF MATERIALSThe dichlorodifluoromethane (commonly known as freon-12) and the dimethyl ether were supplied by Dr. Lyle D. Goodhue., U. S. Department of Agriculture, Beltsville, Md. It was reported that the freon-12 was manufactured by the Kinetic Chemical Co. Wilmington, Del., and the dimethyl ether by the Carbide & Carbon Chemicals Corp., Charleston, W. Va..The materials were obtained in small metal cylinders and were used as received. Before using, the cylinders mere placed in an upright position, and 5 to 6 liters of the gas was released from each cylinder to the atmosphere to remove any trapped air that may have been introduced when the cylinders were filled."

Sep 1, 1947

By John D. Spencer

Surveys to establish the quantity and quality of coals available for metallurgical, industrial, and energy use, investigations to develop better mining methods, and studies aimed at improving the health and safety of those who mine the coal highlighted Bureau of Mines research and technologic work on coal in 1968. Also being developed are more efficient methods of coal preparation, transportation, storage, and utilization. Supplementing this effort are projects designed to assure minimum disturbance of land, water, and air resources. Research centers and laboratories of the Bureau of Mines are listed in appendix A. Publications released during 1968 are cited with the various projects and in appendix C. Organizations that cooperated in the work in various ways are cited in appendix B.

Jan 1, 1969

By A. J. Forney

A high-Btu gas was made at the Bruceton, Pa., laboratories of the Bureau of Mines to demonstrate the feasibility of using the gas as a nonpolluting fuel for automobiles. The pilot plants at Bruceton were revised to combine the processes of coal gasification, gas purification, and catalytic methanation in one overall system. Tests in the Bureau's test automobiles at Bartlesville, Okla., showed the Synthane gas was less polluting than natural gas.

Jan 1, 1972

By F. Garcia, J. Cervik

Recent advances in the commercial separation of gases using membranes have renewed interest in the possibility of applying this technology to the recovery of methane ( CH4 ) from mining operations . This Bureau of Mines report briefly reviews the history of the development of membranes for gas separation , the theory of how they work , and their application to the separation of methane from air and associated problems . However , methane -air mixtures are difficult to separate with membranes because the pertinent gas couples , 02 - N2 , 02 - CH4 , and N2 -CH4 , have poor separation characteristics , as indicated by their separation factors of about 3 or less . Even if these separation factors were substantially higher , there is doubt that methane could be recovered economically from the low concentrations in mine ventilation exhaust ( 2 vol pct or less ) . The exhaust pressures are not sufficient for adequate separation . The power cost of compressing the methane recovered . these mixtures would far exceed the value of New discoveries could make separation of gob hole methane - air mixtures practical . These mixtures have much higher concentrations of methane (from 30 to 100 vol pct ) ; however , for safety reasons , be limited to gob gas with 60 vol pct CH4 or more .

Jan 1, 1988

By Raja V. Ramani, Robert L. Frantz

"In response to the U.S. Bureau of Mines (USBM) Request for Proposal (RFP) for "" the establishment of a Generic Mineral Technology Center (GTC) in Respirable Dust,"" the Mining and Mineral Resources Research Institutes (MRIs) at The Pennsylvania State University (PSU) and West Virginia University (WVU) in association with participating MRIs at Massachusetts Institute of Technology (MIT), and the University of Minnesota (UMN) have prepared the comprehensive research program described herein. Michigan Technological University (MTU) joined the Center as an affiliate after its inception. This program was developed with recognition of the stated objective of the Federal Mine Safety and Health laws which is to "". . . permit each miner the opportunity to work underground during the period of his entire adult working life without incurring any disability from pneumoconiosis or any other occupation-related disease . . . .""Exposure to respirable contaminants in mine atmospheres has long posed a serious hazard to miners. The control of these hazards, some of which can have sudden and catastrophic consequences and some others, slow and long enduring, has been a major concern for labor, management and the government. This concern has manifested itself in four mechanisms of control -- (1) regulatory control through minimum standard setting by the passage of mine health and safety laws, (2) engineering control through design and operation of mines according to the best recommended practices, (3) interaction of dust and lung control through periodic physical examinations, wearing personal protection devices, etc., and (4) legal and social control through workman's compensation laws for occupation related health deterioration."

Aug 31, 1989

By E. F. Foerster

The Bureau of Mines used a diphenyl ether calorimeter to determine the heat contents of natural and synthetic blast-furnace slags. For solid slags, enthalpy (HT-H298) at 1,448° to 1,680° K ranged from 282.1 to 348.5 cal/g (±3 percent); liquid slag values were 400.1 to 514 cal/g (±3 percent) in the temperature range between 1,626° and 1,890° K. Experimental results for liquid slags were 14.3 to 16.2 percent higher than the enthalpies calculated from thermodynamic tables; values for solid slags ranged from 5.3 percent lower to 3.9 percent higher than calculated values. Experimental results for liquid synthetic slags ranged from 14.9 to 24.3 percent higher than the calculated enthalpies; values for solid synthetic slags were from 1.0 to 3.4 percent higher.

Jan 1, 1967

By F. W. Benn

The Bureau of Mines investigated flotation methods for recovering fluorite and byproducts from two samples of the Fish Creek deposit in Eureka County, NV. The preferred method for tre.ating a fluorite-beryllium sample included (1) fluorite rougher and cleaner flotation, (2) desliming at 20 um, (3) muscovite flotation, (4) silicate flotation, (5) sodium hypochlorite wash of silicate concentrate, and (6) beryllium rougher and cleaner flotation from the silicate concen-trate. Laboratory results showed that over 94 pct of the fluorite was recovered in a recleaner concentrate containing 98 pct CaF2, Beryllium flotation produced concentrates containing in excess of 5 pct BeO with recoveries over 70 pet. The preferred method used for a fluorite-mica sample consisted of (1) fluorite rougher and cleaner flotation, (2) desliming at 20 um, and (3) mica flotation using an anionic-cationic collector system. Laboratory results showed that 84 pct of the fluorite was recovered in a recleaner concentrate containing 96 pct CaF2, Mica flotation produced a concentrate containing 95 pct mica at 85-pct recovery.

Jan 1, 1986

By H. E. Peterson

A study was undertaken by the Bureau of Mines to develop a simple, reliable test for field detection of selenium in rocks and soils. Two methods are described for qualitative detection of selenium, dependent upon its form of occurrence and the presence of interfering constituents in the sample. Both methods involve fusion of the sample in a test tube to form elemental selenium that will volatilize and condense as a red deposit on the cooler upper portion of the test tube. The methods are sensitive to 10 parts per million, (p.p.m.) equivalent to 0.001 percent, and can be made semiquantitative by using suitable standard samples. INTRODUCTION Although selenium is widely distributed in the United States, the known deposits are either so small or so low grade that they cannot be processed economically for selenium alone-4/ At present, commercial production is a byproduct of the smelting and refining of base-metal ores, particularly copper.5/ About 0.75 pound of selenium is recovered per ton of electrolytic copper, and small amounts are recovered by special treatment of assorted smelter dusts and fume products. Since selenium is a strategic metal in short supply, new sources are being sought by both Government and private interests.

Jan 1, 1957

By Floyd R. Hertweck

This Bureau of Mines publication contains analyses and related source data for 349 natural gas samples from 26 States and 2 foreign countries. The 3 samples from foreign countries and 339 of the U.S. samples were collected during calendar year 1983. The remaining seven samples were collected earlier, but releases granting permission to publish were not received until 1983. All samples were obtained and analyzed as part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by the mass spectrometer and chromatograph. The results of these investigations are published annually to make the information available to the petroleum industry and the general public. Twenty-seven publications have presented the results of 13,332 gas analyses made prior to 1983. The first three bulletins (1-3)3 contain analyses and related source data on 5,218 gas samples collected from 1917 through 1960; these bulletins have been supplemented annually by information circulars (4-17, 19-24, 26-27) containing 8,104 analyses of sam¬ples collected since 1960.

Jan 1, 1984

"The town of Monson in Piscutaquis County, Maine is the, center of an important site industry. Monson slate has a nation-wide reputation, particularly for electrical switch boards, and the deposits have been worked for the manufacture of such products for many years. Open-pit quarrying is the method most commonly employed in obtaining slate. Underground methods have been used in the Peaon Bottom district near Delta, Pennsylvania, but the quarries that were thus operated are now abandoned. Underground methods have been used more extensively in foreign countries, the most famous example being the slate mines at Angers in France, where an over-head stoping method has been employed successfully for many. It is only under special conditions that underground methods can be successfully used. If the deposit is wide and relatively thin, or if the material is too unsound to constitute a safe roof, open-pit methods must be used, for slate is too low-priced a commodity to justify the heavy expense of any timbering methods. It is only where the deposit is relatively narrow, of great depth, and sufficiently sound to afford a strong roof that ordinary mining may be employed.The best slate beds in two of the three quarries operated at Monson are no worked by underground methods. The chief bed worked by the PortlandMonson Slate Co. is 10 feet thick, stands vertical and strikes N. 63º F. The slaty cleavage is vertical and crosses the strike of the beds at an angle of 5 to 10°. The grain or second direction of splitting is vertical and perpendicular to the cleavage. In addition to the 10-foot bed, to 2-foot beds and one 5-foot bed are available but are not now utilized. In theMonson Maine Slate Co. quarry (the old Pond quarry) a greater number of beds available, but at present quarrying is confined to a single bed about 9 feet thick which dips 30º S.E. and strikes N. 47ºF. The slaty cleavage is vertical and strides N. 45º F., while the grain strikes N. 45-50º W. and is also vertical."

Nov 1, 1920

By Eric R. Bauer

The U.S. Bureau of Mines, in cooperation with a southwestern Pennsylvania coal mining company, BethEnergy Inc., Mine No. 60, Eighty-Four, PA, recently assessed the feasibility of using pre driven recovery rooms (open entry recovery) when longwall mining to increase the productivity of the coal extraction process. Two recovery entries, one 200 ft long and another 600 ft long, were supplementally supported with bolts, channels, and wire mesh, and either fly ash-cement piers or fiber cribs, then mined into by the longwall face. The recovery entries showed little deterioration as the supports provided adequate resistance to the front abutment loading. Compared with conventional recovery methods, the fullface recovery room allowed for panel extraction to be completed nearly 17 days faster and to reduce face equipment move time by 1-1/2 days. The potential productivity increase accompanying recovery rooms is greater than the cost of supporting a fullface recovery room. The fullface recovery room provided over 18 additional production days and the opportunity to mine nearly 68,400 st of coal per year per panel mined.

Jan 1, 1989

By W. S. Sanner

Pyrolysis (destructive distillation) techniques developed at the Bureau of Mines to determine the yield and quality of the products from coal were used to convert municipal (household) and industrial refuse into potentially useful solids, liquids, and gases without adding to environmental pollution. The tests demonstrated that a ton of municipal refuse can be converted into 154 to 424 pounds of solid residue, 0.5 to 6 gallons of tar, 1 to 4 gallons of light oil, 97 to 133 gallons of liquor, 16 to 32 pounds of ammonium sulfate, and 7,380 to 18,058 cubic feet of gas. A ton of industrial refuse, consisting of paper, rags, and cardboard, can be converted to 618 to 838 pounds of residue, 1.5 to 3 gallons of light oil, 68 to 75 gallons of liquor, 12 to 23 pounds of ammonium sulfate, and 9,270 to 14,065 cubic feet of gas. The energy from the gas is more than sufficient to provide the heat for the pyrolysis.

Jan 1, 1970

By William C. Laubengayer, Robert R. Godard, Harry Dobroski

A whole mine, computer-controlled communication and monitoring system for both normal and emergency use is installed and operating in the U.S. Steel Robena Mine complex near Uniontown, Pa. Portions of the system, including the coaxial cable and the key underground and surf ace phones, have been operating for over a year and a half. During this time the basic concept has been modified and new line amplifiers with directional switches have been developed to eliminate some problems in implementing the loopback feature. The quality of the audio and the availability of the system have been outstanding. Since early summer almost all subsystems have been completed. The experience with the telephone system itself, the pocket-pager call alert, section wireless radio, hoistphone, television, environmental monitoring, control and monitoring of equipment, voicedownlink/code uplink post disaster communications, post disaster through-the-earth monitoring, and the system center failure diagnostic routines are reviewed.

By B. J. Dalton

The Bureau of Mines Helium Activity has developed a computer program for use in the reduction of pressure-volume-temperature (PVT) data obtained with a Burnett compressibility apparatus. This program includes important modifications and extensions of some of the methods currently used for treating these types of data and yields statistical information that cannot be obtained from any other published work. The methods of calculation make use of a general nonlinear least-squares technique developed at the Helium Research Center. Because of a need to investigate different functional forms for representing the compressibility factor isotherm, 2, the computer program has been written in such a way that the only additional coding required is the so-called compressibility function subroutine. This subroutine defines the analytical form of Z and certain of its partial derivatives. The program described herein is believed to be the most advantageous for use in treating isothermal Burnett compressibility data.

Jan 1, 1970

SMCRA contains five principal regulatory provisions that form the basis for its implementation: Performance Standards Performance standard safe intended to ensure that all surface mining is conducted in a way that protects the environment and the public and ensures that the mined land is restored to productive use following mining. Permits Before developing a surface or underground coal mine, an operator must have a permit issued under SMCRA. An application for a permit to conduct a surface coal mining operation is a detailed document that consists of text and numeric data describing the proposed mining and reclamation. Information must be furnished on pre-mining environmental conditions, existing land use, proposed mining and reclamation, how the performance standards will be met, and the post-mining land use. This provides the regulatory authority with the information necessary to determine that the operation can be conducted in accordance with the regulations. Performance Bonds Before a permit can be granted, an operator must post a performance bond sufficient to cover the cost of reclaiming the site in the event the operator fails to complete reclamation. The bond is not fully released until all performance standards have been met and reclamation of the site has been determined to be successful after five years in the East and Midwest, and after 10 years in the arid West. However, the bond can be partially released as various phases of reclamation are completed. Inspection and Enforcement If a violation of SMCRA or of a state surface mining and reclamation law is observed, an inspector issues a notice of violation to the operator. The violation must be corrected within a specific time, and the operator may also have to pay a fine based on the severity of the violation. If the violation is not corrected, acessation order is issued to immediately stop active coal mining, and the operator must pay a fine. If a violation is especially serious (for example, creates an Following reclamation, the land was immediately put back into agricultural production. Today, grain and corn crop yields have continually exceeded targets. 2 imminent danger to public health or safety or causes significant damage to land, air, or water resources) the inspector immediately issues a cessation order. An operator must correct all violations in order to obtain permits for new mines. Lands Unsuitable For Mining Congress recognized that certain coal deposits cannot be mined without permanent damage to unique cultural or natural resources. As a result, SMCRA protects these resources in two ways: It prohibits mining within the boundaries of national parks, forests, wildlife refuges, trails, wild and scenic rivers, wilderness and recreation areas; in areas which will adversely affect sites listed on the National Register of Historic Places; and within a restricted distance of occupied dwellings, public roads, buildings, parks, schools, churches, and cemeteries; and Provides a process that allows anyone whose interests may be adversely affected by proposed mining to petition to have specific lands designated unsuitable for mining.

Jan 1, 1992

By W. H. Young

PRODUCTION of bituminous coal and lignite increased substantially in 1964. There were upward trends also in consumption, average value, exports, mechanization, and productivity. However, a significant decline in employment continued. Production.-The output of bituminous coal and lignite in the United States in 1964-487 million tons-was 6 percent greater than the 459 million tons produced in 1963. The gain was attributed largely to expanded consumption by the electric utilities, greater use at coke ovens, and an increase in exports.

Jan 1, 1965

By M. M. Tilman

The Bureau of Mines conducted research into the dispersion strengthening of lead by the coprecipitation method. Commercially available reagents in water solutions were reacted to form homogeneous precipitates of lead and aluminum compounds. The resulting precipitates were roasted to oxides and reduced in hydrogen to form mixtures of lead powder and alumina. The powders were isostatically pressed into billets which were extruded into rods. The rods were rolled into strip to provide material for testing. Alloys containing 0.5, 1, 2, and 3 nominal volume-percent A1203 were tested in short-time tensile tests and in tensile creep tests. An alloy of Pb-3 volume-percent A1203 exhibited an average tensile strength of 8,570 psi after rolling to 75-percent reduction at 125° C but had no measurable elongation. Alloys of lower A1203 content provided a better compromise between tensile strength and ductility. For example, an alloy of Pb-0.5 volume-percent A1203 had an average tensile strength of 6,590 psi with 9-percent elongation after rolling to 75-percent reduction at 125° C. Creep rates of dispersion-strengthened Pb-A1203 alloys were below 1 percent in 10,000 hours at stresses of 2,000 to 4,000 psi.

Jan 1, 1971

By C. P. Lazzara, R. A. Franks, G. F. Friel, J. C. Edwards, J. J. Opferman

A National Institute for Occupational Safety and Health’s (NIOSH) mine fire detection re-search project was undertaken to evaluate multiple mine fire sensor types for nuisance alarm discrimination. The response of multiple fire sensor types to three small coal fire and three small conveyor belt fires in the presence of diesel emissions was evaluated in NIOSH’s Pittsburgh Research Laboratory (PRL) Safety Re-search Coal Mine (SRCM). An array of fire sensors which included an optical and ionization smoke sensor, a chemical cell CO sensor, and Metal Oxide Semiconductor (MOS) sensors, was used to sample the diesel engine and fire source emissions. The mine fire detection experiments demonstrated the ability of a MOS sensor with a bimodal response to NOx and products-of-combustion (POC) to respond to the onset of smoldering combustion in the presence of CO and POC particulates from a diesel locomotive. As part of an in-mine evaluation in an operating coal mine, the MOS NOx responsive sensor and an ionization smoke sensor was demonstrated as a method to discriminate diesel emissions and cross-interference of H2 on a CO chemical cell fire sensor at a battery charging station. The reinforcement of mine fire sensor information with the use of multiple sensor types, such as an MOS sensor and ionization and optical smoke sensors, is shown to be important for nuisance alarm discrimination and early mine fire detection.