Search Documents

The coal-bearing strata of Oklahoma occur in the eastern part of the state over an area of 14,500 square miles, 20.7 percent of the state's total area. Commercially valuable deposits of bituminous coal cover about 8,000 square miles in seams ranging from ten inches to five feet thick. Estimated reserves in Oklahoma are 1.6 billion tons, representing 0.3 percent of U.S. coal reserves. The vast majority of coal mined in Oklahoma used in a single power plant within the state. Oklahoma gained primacy when its regulatory program was conditionally approved January 19, 1981. Authority for the state to administer the Abandoned Mine Land program was granted January21,1982. On April 30,1984, the Office of Surface Mining substituted direct federal enforcement of the inspection and enforcement portions of the Oklahoma program. This substituted enforcement was based upon a finding by OSM that Oklahoma had not operated the inspection and enforcement portions of its program effectively. As of January 1, 1986, Oklahoma inspection and enforcement authority was reinstated. Full program authority was granted to Oklahoma on January 14, 1986.

Jan 1, 1992

Establish a procedure for reliably determining cation exchange parameters at an in situ mining site. The Problem Predicting the movement rates of pollutants from waste disposal sites requires reliable measurements of cation exchange parameters since cation exchange can retard pollutant movement. Reliable measurements of these parameters are also required for predicting the length of time needed to restore groundwater quality after in situ mining. Cation exchange is otten the controlling mechanism for the replacement of leach solution cations by the cations in the returning ground-water. Unfortunately, laboratory measurements using core samples are of minimal reliability. The uneven clay distribution at most sites produces a high variability in laboratory results. In addition the flow pattern in the laboratory tests is different from that in the field. Approach Bureau of Mines research has developed a field-test procedure that is quick and yields reliable and representative data. A corresponding data analysis procedure was also established in order to verify the' applicability of the computer simulation model of cation exchange used in the analysis, and of the general analysis procedure, with actual field data.

Jan 1, 1986

By William G. Pariseau

The research reported here concerns a four year study of the rock mechanics aspects of two underground hardrock mine study stopes. The first study was conducted at Anaconda Minerals Company's Carr Fork Mine near Tooele, Utah. The second study was conducted at the Homestake Mining Company's Homestake Mine In Lead, South Dakota. Both case studies were cooperative efforts of mining company personnel, the Spokane Research Center of the Bureau of Mines and the Department of Mining Engineering, University of Utah. Large diameter (6 1/2 In.) blastholes were an integral part of the stoplng method at each mine. A true vertical crater retreat (VCR) method was used at the Homestake Mine, while a vertical bench mining method (VBM) was used at the Carr Fork Mine. VCR and VBM methods were developed In the 1970's; they offer significant productivity gain and are now used throughout the world. The new technology, however, brings with It a requirement for more sophisticated engineering design and control. Since there are no personnel in a VCR or VBM stope, all ground control Including dimensioning of stopes and pillars and the layout of cable bolt assays or other artificial support must be done in advance of production blasting. Accordingly, the objective of the research study was the establishment of a procedure for optimizing stops and pillar sizes. The approach taken was In each case a combination of mine measurements of the study stope response to mining, laboratory testing for rock properties and In situ stress measurements of the premining stress field, and theoretical calculations of the study stope response to mining. All calculations were done with the UTAH-II finite element computer program. Simulation of the blasting sequence gave a correlation of 0.88 between measured and calculated extensometer readings (Incremental relative displacements) at the Carr Fork Mine where other 30 Instrumentation boreholes were used to monitor the test stope response. A correlation of 0.84 was obtained at the Homestake Mine where 19 instrumented boreholes were used for monitoring purposes. These high correlations validated the computer mode and calibrated It for rock mass properties. The calibrated model was then used In parametric studies of alternative design layouts.

Jan 1, 1985

To improve efficiency in producing clarified water from mineral and metallurgical processing streams containing suspended particles. Approach Particles suspended in mineral and metallurgical processing streams are filtered out by granular magnesium oxide (MgO) used as the medium in deep bed filters. How It Works MgO is substituted for the silica sand or garnet sand currently used in conventional deep bed filters. These filters presently consist of a 24- to-48-inch-deep layer of either silica sand or mixed media, consisting of a stratified combination of anthracite coal, silica sand, and garnet sand. As waste water containing fine solids is percolated through the granular bed, the suspended particles become attached to the filter grains. When MgO replaces sand as a filter medium, the overall filter capacity is generally increased 50 to 80 percent, and no equipment modifications are necessary for filter operation. MgO is unique because it has a positive surface charge in water while most suspended materials are negative. The attraction of these negatively charged suspended particles to MgO enhances filtering performance. As is necessary for all good media, MgO is insoluble and nontoxic.

Jan 1, 1983

The coal deposits in Alaska occur in several major coal fields or basins. The deposits underlie about a quarter of the state, an area larger than Montana. Approximately 60 percent of the coal is bituminous and 40 percent is subbituminous. Less than one percent is lignite or anthracite. Although known coal reserves are estimated at only 6.1 billion tons (about 1.25 percent of U.S. reserves), estimates place the hypothetical reserves at 5.5 trillion tons and the identified reserves at 170 billion tons. The differences are due to limited exploration programs within the state. Conditions affecting mining and reclamation are unique to Alaska because of its extreme northern latitude. For example, permafrost occurs in about 75 percent of the state; tundra vegetation occupies vast treeless regions; and the climate is characterized by extremely cold winter weather and a short summer season. In addition, hydrologic conditions are considerably different from those in other states; major streams fed by silt-laden glacial melt water contain greater concentrations of natural sediment than the effluent discharge limits permitted by federal regulations. Also, some coal field locations are subject to potentially high seismic risk. These factors make coal mining and reclamation in Alaska more difficult than in other states. Alaska's program to regulate surface coal mining was approved May 2,1983. The Abandoned Mine Lands program was approved December 23,1983.

Jan 1, 1992

By Fred D. Wright

A compressor and utility station, which is believed to be one of the largest mobile units of this type ever constructed, was placed in operation at the Bureau of Mines experimental oil-shale mine near Rifle, Colo., during. 1949. This mobile unit mounts two 770-cubic-feet-per-minute air compressors, a 2,500-gallon water tank, and a 200-cubic-foot air receiver. The mobile base of the unit is a 30-ton trailer 30-feet long and 12-feet wide. Prior to the construction of this unit, compressed air was supplied to underground workings through pipe lines connecting with a stationary compressor plant on the surface. The power consumed in supplying compressed air to underground drilling crews was 0.531 kw.-hr. per ton of shale broken. Use of the mobile unit has cut this figure to 0.421 kw.-hr. per ton of shale broken and, more important, has eliminated the cost of installing and maintaining underground air and water lines.

Jan 1, 1950

By Bill M. Stewart, Philip W. Patton, Curtis C. Clark

Handling materials in underground mines continues to be a major safety problem. To help reduce materials-handling injuries, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are investigating those materials-handling tasks in underground mines that appear to generate a high number of injuries. Data from the Mine Safety and Health Administration for the years 1989-1999 were studied to find out if there were any trends in materials-handling accidents and if so, to determine what tasks were involved and the sources of injuries. Several underground coal and metal mines we revisited to document innovative materials-handling technologies. Considerations for safety training and mechanization needs for continued reduction in materials-handling injuries are described.

By G. W. Grove, G. L. FreAS

One of the chief hazards in mining bituminous coal is the accumulation of coal dust in the mines . When coal dust is thrown into suspension , it can be ignited and exploded by electricity through short -circuiting of mining machinery and trolley wires , or by arcs and sparks . The Bureau of Mines has endeavored to assist the coal -mining industry in preventing disasters from this cause by urging that all bituminous -coal mines be rock -dusted . As it has been difficult to convince some mining men of the danger of ignition of coal dust and of the effectiveness of rock dusting in preventing widespread explosions , a small , portable , coal -dust - explosion gallery has been designed to demonstrate the explosibility of bituminouscoal dust . Such galleries are furnished to Bureau engineers , inspectors , and safety instructors to illustrate visually and impressively the Bureau's accident -prevention educational work on the causes and prevention of dust explosions in bituminous -coal mines .

Jun 1, 1949

By Harold E. Heide

Although the United States has been the largest consumer of tin, only a small quantity of tin was produced or. the North American Continent during peace times, and thy deficiency was made UP by foreign imports. Because the most important sources of tin wore cut off by the war with Japan, it became necessary to increase imports from South America and Africa and, if possible, develop domestic tin reserves. Most of the tin produced in North America has come from the Seward Peninsula, Alaska, and a substantial portion of this was produced from the Potato Mountain area. Tin was first identified as occurring in the Seward Peninsula by A. H. Brooks in 1900, when a part of heavy concentrates from Anikovik River and Buhna Creek, one of its tributaries, proved to be stream tin. 4/ His report was given considerable publicity by the daily press, and the first steamers north in 1901 carried a number of prospectors bound for the Seward Peninsula to search for tin. The deposits of stream tin on Buck Creek in the Potato Mountain area were discovered in the fall of 1901. 2/

Jan 1, 1949

By James R. Coldwell

Mining and processing cost analyses were conducted by the U.S. Bureau of Mines on stratiform zinc-lead-silver, coal, and stratiform barite deposit types that are found in the Colville Mining District. Reserves and gross revenues which would allow these deposits to be minable were modeled. A 15% Discounted cash-flow rate-of-return economic threshold was selected as the minimum acceptable return on investment for the three deposit types. The economic modeling indicated combinations of grades and tonnages for stratiform sulfide deposits that could be economically viable for orebodies ranging in size from 25 to 130 million metric tons. The gross revenues for a surface mine range from $200/mt for a 5,000 mtpd operation using the proposed South corridor to $140/mt for a 17,000 mtpd mine using the proposed North corridor. The economic modeling indicated underground coal mining was subeconomic for deposits ranging in size from 42 to 250 million metric tons. The required gross revenues ranged from $300/mt for a 2,200 mtpd mine to $21 D/mt for a 13,000 mtpd mine. The economic modeling indicated supplying projected in-state barite demand was subeconomic for the three seasonal surface mines modeled. The required gross revenues ranged from $600/mt for a 90,000 mtpy mine to $840/mt for a 6,000 mtpy mine.

Jan 1, 1995

By Arthur L. Murray

"INTRODUCTION In compliance with those provisions of the organic act establishing the Bureau. of Mines which relate to improvement of health conditions of persons engaged in the mining, preparation, or treatment of mineral substances, sanitary surveys have been made of towns and villages housing the coal miners, metal miners, and mill and smelter employees of Utah.The purpose of the surveys is to afford studies of conditions prevailing in the various mining and smelter towns so far as concerns housing, water supplies, sewage disposal, refuse disposal the handling of foodstuffs, general sanitation, wash and. change houses, and the control of preventable diseases, all of which directly or indirectly have a bearing on the health and efficiency of employees and their families. Certain other factors have been added to the general sanitary surveys such as school and recreational facilities, which have a decided influence on contentment and efficiency. Through comparisons of favorable and unfavorable conditions and practices, and the dissemination of such information, improvements can be effected which will benefit both the employees and the employers.ACKNOWLEGMENTSAcknowledgment is made of the many courtesies shown by the officials of companies and towns visited. In some instances the towns were entirely under the control of officials of mining companies, being on company property whereas, in other instances, the towns wars incorporated not under company management. Particular acknowledgment is made of the assistance given by the Utah State Board of Health through Health Commissioner Dr. T. B. Beatty."

Oct 1, 1932

Develop and demonstrate a lightweight material that has low thermal conductivity and that would be suitable for placement using shotcrete methods. This material could be applied in deep, hot mines where mine drifts must be insulated. Its use would decrease mine refrigeration needs and reduce energy costs.

Jan 1, 1994

By Thomas M. Barczak, Ron Smith

Steel liner plates, which are bolted together to form a shell, are commonly used to provide temporary protective linings in the tunneling industry to ensure the stability of the tunnel and safety of the workers until more permanent ground reinforcement can be installed. As the ground deforms to try and close the opening, the liner plate is radially stressed, and by deforming redistributes these loads back to the surrounding insitu earth. Grouting behind the plates is done to fill any voids and ensure uniform contact to the strata around the back of the plates. Another function of the liner plate in some applications is to act as a platform or structure for the mining machine to react against in order to develop the necessary forward thrust to be able to excavate the face. In this case, the liner plates are loaded axially as a horizontal column of bolted liner plate rings, creating a jacking force against the liner plate assembly. In general, the buckling strength of the plate sections determines the jacking force capacity. Historically, the jacking force capacity of tunnel liner plates has been theoretically determined by some simplistic equations developed from tests of single liner plates. Recently, full-scale tests on a complete circular section of bolted liner plate ring segments have been conducted in the NIOSH Safety Structures Testing Laboratory using the unique Mine Roof Simulator to apply controlled loading in a manner that simulates the real world environment. Due to the unique size and capacity of the Mine Roof Simulator, these are believed to be the first full-scale tests conducted on the jacking force capability of tunnel liner plate rings. These tests indicate that the previously used theoretical equations tend to over predict the jacking force capacity of these tunnel liner plates. Unanticipated deformations in the field have been observed at loads below these theoretical design loads, therefore, a more accurate determination of the jacking force capability was needed. This report summarizes the full-scale test results, examines design parameters that impact the jacking force capability, and develops new mathematical models to improve the prediction of design loads.

By David C. Oyler, Paul B. Stubbs

The Bureau of Mines and United States Steel Corp. are conducting a joint project to monitor formation pressures at a large (23-well) coal- bed gas drainage field near Oak Grove, AL. Three monitor holes were drilled in late 1981, and pressure monitoring began in December 1981. The Bureau of Mines direct method was used to obtain gas content data from cores taken in the monitor holes. Comparison of the 1981 gas con- tent data from the monitor holes with initial gas content values obtain- ed from the production wells in 1977 indicates a 50-pct reduction in ad- sorbed gas content inside the pattern and a 29-pct reduction at one point 500 ft outside the pattern. The combination of pressure and gas content data has also allowed an in situ isotherm curve, relating the formation pressure to adsorbed gas content, to be developed for the area of the production wells. From the current rate of pressure decline (1 lbf/inz per month), the observed changes in gas content, and the isotherm curve, it appears that most of the early gas production came from within the pattern, but since 1981 (and possibly earlier) most of the gas produced has been migrating to the wells from outside the pattern area.

Jan 1, 1985

By E. F. Divers

This Bureau of Mines report describes the results of a program to develop small, rugged mechanical dust collectors (scrubbers) with high dust collection efficiency and low energy comsumption for controlling dust in coal mining operations. All of the scrubbers described are similar in configuration and are powered by 6-hp, 2,000-ft3/min vane axial fans. Air pressure differential is less than 6 inches water column. Height of the scrubbers? including fan is less than 14 inches, width is less than 16 inches, and length is less than 45 inches. The flooded fibrous-bed scrubber achieved respirable (less than approximatey 7 µm) dust collection efficiencies of 95 percent. The small-diameter-cyclone scrubbers showed about 92 percent efficiency and can be best where excess water is a problem. The wetted brush scrubber showed 88 percent efficiency at low cost, and the wetted fan scrubber showed a slightly lower efficiency (87 percent) but offered the smallest size and cost. A suitable water droplet eliminator is described.

Jan 1, 1978

This chapter summarizes data on crude mineral production for the United States, its island possessions, and the Common-wealth of Puerto Rico. Included also are tables that show the principal mineral commodities exported from and imported into the United States, and that compare world and U.S. mineral production. Except for the mineral fuel commodities, the detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. In October 1977, responsibility for the collection of data on mineral fuels-coal, petroleum, natural gas, and natural gas liquids-was transferred to the newly created Department of Energy. Although chapters covering these commodities will no longer appear in Volume I of the Minerals Yearbook, quantity and value data have been included in most of these summary tables to maintain statistical consistency in State and national value of overall crude mineral output. This shift in responsibility has also resulted in changes to the composition of the "Nonmetals" and "Mineral Fuels" groups in table 1 and table 2. The commodities-asphalt and related bitumens (natural), carbon dioxide (natural), helium, and peat-have been removed from the "Mineral Fuels" group, and are now included under the "Nonmetals" group. There has been no change in the components of the "Metals" group.

Jan 1, 1980

By Albert L. Toenges

A phase in strip mining of bituminous coal is the overturning of the surface of the land. The ;purpose of this report is to acquaint the operators and others interested in stripping with the work that has been done in certain States to reclaim the surface of land from which the coal has been removed by this method of mining. The preparation of this manuscript follows an extensive study of the subject in the field in the course of which a large number of strip mines were visited. ACKNOWLEDGMENTS The information used in the report was obtained through the courtesy and cooperation of the operators of the mines visited, State officials and educational institutions, and others interested in the subject.

Jan 1, 1939

By Julius Roth

Flyrock is the source of most of the injuries and property damage in a majority of blasting accidents in surface mines. A quantitative correlation between shot conditions and maximum flyrock range can be used to define a "blasting area" in which no personnel or equipment should be present during a shot. The approach used was to develop a model that correlates shot conditions and initial flyrock velocities and permits computation of flyrock range from ballistic trajectories. The Gurney formula for velocity of explosively-propelled plates or fragments was adapted to explosively-propelled flyrock from vertical rock faces or from bench tops. The modified Gurney formula was then "calibrated" with measured flyrock velocities from mining and explosives literature. Charts were then developed for possible field use which give maximum flyrock range as function of shot conditions. The model indicates that for flyrock from vertical faces, borehole diameter, minimum burden and height of explosive column define maximum flyrock range for a given explosive, shot in a given rock. For flyrock originating from bench tops, flyrock range appears to be controlled by the distance of the top of the explosive column to the borehole collar, by total explosive load per borehole and, to a lesser extent, by borehole diameter.

Jan 1, 1979

By Albert L. Toenges

A phase in strip mining of bituminous coal is the overturning of the surface of the land. The purpose of this report is to acquaint the operators and others interested in stripping with the work that has been done in certain States to reclaim the surface of land from which the coal has been removed by this method of raining. The preparation of this manuscript follows an extensive study of the subject in the field in the course of which a large number of strip mines were visited. ACKNOWLEDGMENT The information used in the report was obtained through the courtesy and cooperation of the operators of the mines visited, State officials and educational institutions, and others interested in the subject.

Jan 1, 1939

By G. L. Fitzpatrick

Future applications of seismic holography to "seismically transparent phase objects," such as rock inclusions, fracture zones, liquid-filled cavities, etc., will require techniques to improve the poor image contrast generally characteristic of these objects. Although conventional phase-contrast enhancement techniques could be used, these methods involve additional optical elements such as quarter-wave spatial filters. Owing to the anticipated practical difficulties of properly alining such optical devices and properly locating poorly defined image planes and filter planes, this approach is not considered to be well-suited to the case of seismic holograms and their laser reconstructions. Results similar to those achieved with spatial filters may be obtained without filters by specially processing the seismic hologram data. The new process, which is an extension of Gabor's subtraction holography, achieves an improvement in contrast by an interferometric technique. The process involves adding a ?before" hologram without an object present to a 90° phase-shifted "after" hologram with the object present. Then, the combination is reconstructed with a laser or by computer. Not only is the image contrast improved in such processed holograms, but the images are also phase-contoured. In general, the latter feature is not to be expected when conventional phase-contrast enhancement techniques are employed. The new technique is experimentally verified by examining computer-generated synthetic seismic holograms rather than by examining actual seismic field data. However, results of this study are directly applicable to real seismic data and should prove useful in future applications of seismic holography.

Jan 1, 1973