Search Documents

By E. A. Mihok

A pilot plant for treating mine drainage by neutralization with limestone was designed, fabricated, and operated by the Bureau of Mines. The process consists of (1) producing a very fine (minus 400-mesh) limestone slurry, (2) mixing the slurry with the mine water, (3) aerating the resulting mixture to remove carbon dioxide and precipitate iron, and (4) separating the solids from the liquid by sedimentation. A mine discharge of pH 2.8, containing 1,700 ppm total acidity, 36 ppm ferrous iron, and 360 ppm total iron, was treated at rates from 300 to 400 gpm. The treated water ultimately reached a pH of 7.4 and contained no detectable iron. The resulting sludge compacted to approximately one-third the volume of sludge from mine water neutralized with lime. The advantages of the limestone process, compared with the conventional lime process are as follows: Widespread distribution and lower cost of run-of-mine, indigenous limestone; simplicity of plant design; reduced hazards and plant operating and maintenance costs accruing from the use of a less reactive chemical agent; higher solids concentration of the precipitated sludge; and no deleterious effect caused by accidental overtreatment. While total process costs could not be determined, it is conservatively estimated that the cost of treating mine water by the limestone process is one-third to one-half the cost of the lime process, depending on the characteristics of the water to be treated and the availability and quality of limestone used.

Jan 1, 1968

By Th. G. Sahama

This paper contains some new heat-of-solution measurements of geikielite (MgTiO3), limonite (FeTiO3), fayalite (Fe2SiO4), and a natural forsterite in mixed acid (HF +HCl) and gives the results of a thermodynamic attack on the problem of stability of geikielite in rocks.

Jan 1, 1949

By Thomas Varley

"Concentration, ore-dressing, or the dressing of minerals are common terms used in metallurgy and indicate processes of separating valuable minerals from worthless gangue. It is understood, of course, that the products from such processes, being separated from the various minerals and gangue, are ready for commercial sale or for further treatment by smelters and refineries.Gravity concentration takes advantage of the difference in specific gravity of the various constituent minerals and gangue of waste material in the ore. The two most common forms of concentration by this means are jigging and table concentration. Jigs usually are used in the separation of relatively coarse material and the tables for the finer material, the line of division in general being about 20 mesh.There are mar factors to be considered .before a decision can be made as to what method would be best adapted to the successful treatment of an ore and only by careful experiments can this be determined. Among the important factors to be considered are. The nature of the minerals present, their physical and chemical relations to the gangue material, and the gangue material itself. Perhaps the most important is the number of minerals present and their relation to each other.Metals exist in ores in three principal forms -- sulphides, oxides or carbonates, and native. Concentration by gravity methods is in general best suited to sulphide ores, although in some places considerable success has, been obtained in the concentration of oxide ores by gravity methods."

Apr 1, 1920

By T. J. Ballard

The Union Copper mine is in the Gold Hill district; Rowan and Cabarrus Counties, N. C. The mine was discovered in 1799 and first worked as a gold mine; but copper was encountered at depth, and the property became an important producer of copper. It is estimated that the mine produced 5,000,000 pounds of copper before operations were discontinued in 1907. As part of the strategic minerals program, the Bureau of Mines conducted a development project on the property from July 1943 to November 1943. Eight diamond-drill holes totaling 2,500 linear feet were drilled to delineate the ore body. Analyses 205 core samples were made. Tabulations of sample analyses and drill-hole logs are presented in this report.

Jan 1, 1948

By H. B. Freeman, E. J. Gleim

During the 12 months ended July 1, 1931, engineers of the Bureau of Mines examined electrical equipment in 80 bituminous-coal mines. The purpose of these examinations was to ascertain the condition of such equipment with respect to possible hazards of gas and dust ignitions, also of shock. Although only 3 of the 80 were being worked with open lights and therefore did not use explosion-proof equipment, there were others where electric cap lamps were used by the men but where it was apparently assumed that conditions as to gas and dust did not require equipment designed to give protection against ignitions. Early in its history the United States Bureau of Mines originated certain standards covering the construction and testing of electrical equipment in order to minimize the dangers of ignitions from exposed electric sparks and flashes ; accordingly, it is comparatively easy to determine wherein a machine built to these standards falls short of continuing to meet them if damaged or neglected. Many so-called flame-proof and dust-proof machines, however, have not been built to any standard comparable with that developed by the Bureau of Mines. In addition, certain machines have parts which pass Bureau of Mines tests, but do not satisfy the full requirements in other respects, and others make no pretense of inclosing the spark-producing parts. It is not uncommon to find two or more of these various types in the same mine with " permissible " machines, the type that has been built to conform to the Bureau of Mines standard. Consequently, inspection of nonpermissible machines becomes somewhat difficult without a standard of comparison. Because of its unprotected condition obviously open-type electrical equipment must be used with great care, if at all, in a mine where precautionary measures are adopted in guarding against gas and dust ignition. The unsafe nature of such equipment is widely recognized. For that reason it is to be installed only where there is no likelihood of gas being present. It is not apparent to some, however, why flame-proof and dust-proof equipment and equipment having tested parts should not be regarded in the same light as permissible equipment.

Jan 1, 1932

By D. Dolinar, T. P. Mucho

Horizontal stresses are caused by global plate-tectonic forces. During 1995 alone they were largely responsible for the closing of two longwall mines in the United States. This paper presents six case histories from Pennsylvania, West Virginia, Kentucky and Alabama. In each case, a mine encountered roof falls or difficult ground conditions at the headgate caused by horizontal-stress concentrations. The problems are detailed, and the control measures adopted are described. In most cases, nearby longwall panels without stress concentrations were trouble free. The paper also discusses detailed measurements that were made at two adjacent Pennsylvania longwalls. One headgate was oriented to avoid a horizontal-stress concentration, and the other was not. Eliminating the stress concentration dramatically reduced roof support loads and roof deformation. The paper concludes that proper panel orientation and sequence is the key to maintaining headgate ground control. The optimum orientation is not parallel to the maximum horizontal stress, as previously thought, but rather it is 20° in the stress shadow of the gob. Other stress-control techniques, including artificial support, are briefly discussed.

Combine the MSHA and OSHA versions of the HazCom Helper into one easy-to-use software tool.

Jan 6, 2007

By Frank E. Cash

As a part of its safety program the United States Bureau of Mines has fostered the development, use, and improvement of portable electric mine lamps. Although there is still need for better illumination in mines and the replacement of open lights has been slow, improvement in electric cap lamps and increase in their use indicate one phase of recent progress toward safer and more efficient mining This report is the result of a recent survey of electric-lamp installations in the Alabama mining; district; it shows the misuse, increase in use, and relation to certain classes of accidents of these installations.

Jan 1, 1935

By E. G. King

In continuation of the study of thermodynamic properties of the common interoxidic compounds of ferroalloy elements, this report gives the results of low-termperature heat-capacity measurements and entropy evaluations of the monotungstates of sodium, magnesium, and calcium. Previous reports4 5/ of this laboratory dealt with low-temperature heat capacities, entropies, and heats of formation of the sodium vanadates. Heat-capacity measurements of the monotungstates of sodium, magnesium, and calcium (Na2W04, MgW04, and CaW04) were conducted throughout the temperature range 51° to 298° K. The entropies at 298° K. were evaluated and then combined with entropy data for the elements and oxides to obtain entropies of formation. This information is an essential part of the data needed for thermodynamic appraisals of chemical reactions of these substances. No similar data for any tungstate are to be found in the literature.

Jan 1, 1961

By Larmon J. Heath

The Bureau of Mines explored the use of air or natural gas for recovering additional oil from natural water-drive reservoirs with little or no original gas saturation. Engineering and production data for a field in the Mid-Continent area, results of limited laboratory experiments, and data shown in the literature were considered. Injecting air into a water-coned well could seriously damage the well. Injecting natural gas into the watered-out zone could improve the producing water-oil ratio. In the reservoir studied, oil recovery can be increased by injecting natural gas to decrease water-oil ratios. Laboratory tests on a core from the field show an increase in oil recovery of 7.6 percent of the original oil in place as a result of increasing the free gas saturation. This recovery could amount to as much as an additional 6 million barrels of oil from this field.

Jan 1, 1966

By F. W. Lee

This paper purposes to outline briefly results of seismic measurements made in the vicinity of blasts in a mine and in open-quarry operations. It endeavors to examine the amplitude and frequency of such vibrations as influenced by the loading, geology, and distance from the source and includes comments on factors that may index the destructiveness of a vibration and a method for measuring the stresses produced. There seems to be no simple mathematical analysis of the transmission of seismic energy through the ground, and experimental observations are at present most feasible. SEISMOLOGIC INSTRUMENTS Instruments developed by the Bureau of Mines for recording ground vibrations from quarry blasting comprise a new type of seismometer, oscillators, and a recording oscillograph. The seismometers respond to vibrations reaching them through the earth and transmit their characteristics by electric current to the oscillograph, where they are recorded by a beam of light on a moving strip of sensitized photographic paper. The seismometers are so constructed that their sensitivity to earth vibration can be controlled, thus keeping the amplitude of the recorded wave within bounds on the paper. Each instrument has been calibrated against vibrations of known intensity and frequency so that correction factors are known for the idiosyncracies of each unit. Moreover, each seismometer is calibrated in the field for its particular sensitivity setting at each blast. By these controls the actual movement of the earth due to vibrations of one ten-thousandth of an inch can be accurately measured.

Jan 1, 1936

By F. W. Lee

This paper purposes to outline briefly results of seismic measurements made in the vicinity of blasts in a mine and in open-quarry operations. It endeavors to examine the amplitude and frequency of such vibrations as influenced by the loading, geology, and distance from the source and includes comments on factors that may index the destructiveness of a vibration and a method for measuring the stresses produced. There seems to be no simple mathematical analysis of the transmission of seismic energy through the ground, and experimental observations are at present most feasible. SEISMOLOGIC INSTRUMENTS Instruments developed by the Bureau of Mines for recording ground vibrations from quarry blasting comprise a new type of seismometer, oscillators, and a recording oscillograph. The seismometers respond to vibrations reaching them through the earth and transmit their characteristics by electric current to the oscilloglaph, where they are recorded by a beam of light on a moving strip of sensitized photographic paper. The seismometers are so constructed that their sensitivity to earth vibration can be controlled, thus keeping the amplitude of the recorded wave within bounds on the paper. Each instrument has been calibrated against vibrations of known intensity and frequency so that correction factors are known for the idiosyncracies of each unit. Moreover, each seismometer is calibrated in the field for its particular sensitivity setting at each blast. By these controls the actual movement of the earth due to vibrations of one ten-thousandth of an inch can be accurately measured.

Jan 1, 1936

Develop geophysical techniques suitable for enhancing miner safety. Specifically, to use geophysical methods to detect hazardous conditions in a rock mass in deep underground mines as well as to assess the mechanical integrity and monitor changes of the rock.

Jan 1, 1997

By E. D. Gardner

"A fire hazard exists in nearly all mines. Progressive mining companies recognize this danger and take all possible precautions to prevent any conflagrations, but in spite of such safety measures, mine fires do occasionally occur and endanger life and property. In order to be prepared for such an emergency, miners are trained in the use of self-contained breathing apparatus and the necessary fire-fighting equipment is kept on hand. Men trained to wear breathing apparatus can penetrate workings full of poisonous fumes, but in order to successfully combat fumes or to rescue miners, the rescue crews must be trained in fire-fighting operations and know how to proceed with a minimum loss of time when they get to the scene of action.In order to perfect fire-fighting plans and to train men of the Globe-Miami district under conditions approximating those found at an actual mine fire, mine-reseue maneuvers were held at Globe, Arizona, on October 17-20, inclusive. The work was done under the direction of Orr Woodburn, director, and his associates of the Globe-Miami District Mine Rescue and First Aid Association. He was assisted by Albert Tallon, safety engineer, and Herbert Finnegan of the Old Dominion Co.; Herbert Hodson, safety engineer for the Inspiration Consolidated Copper Co.; A. 3. Martinson and J. M. Harrington of Car One, and F. D. Gardner of the Southwest Station, Bureau of Mines. Invitations were issued to mining men likely to be interested and representatives of mining companies from other districts were present and observed the work.The Globe-Miami District Mine Rescue and First Aid Association is maintained by the mining companies in the district and each company contributes to the organization's support in proportion to the total number of men on the pay roll. A central station*, between Globe and Miami, has been established and a truck with 10 sets of 2-hour self-contained breathing apparatus and the necessary accessories is always in readiness to respond to a call to any of the mines in the district. Besides being in readiness for emergency work, the station employees train men in the use of mine-rescue apparatus and in first-aid to the injured at the mines of the association. The Globe-Miami Mine Rescue organization has been developed to high point of, efficiency under Mr. Woodburn's direction and is one of the best in the country. The three largest mines of the district such maintain a crew of 15 men trained in the use of breathing apparatus, and other mines keep crews of 5 men each."

May 1, 1923

By E. Kamon

This report summarizes completed research pertaining to the reaction of human subjects exposed to Self-Contained Breathing Apparatus (SCBA) stressors during escape conditions (viz., resistance breathing, C02 breathing, hot air breathing, and static positive facepiece positive pressure breathing) and the development of an automated breathing and metabolic simulator (ABMS). Volume I contains summarizes of the studies performed under this contract. Volume II is an appendix which contains more detailed descriptions of these studies.

Jan 1, 1984

By W. W. Adams

"The National Safety Competition of 1930, the seventh annual contest conducted by the United States Bureau of Mines to promote safety in the mines and quarries of the United States, has been concluded, and the five winners of the bronze trophies, The Sentinels of Safety,' which are provided by the Explosives Engineer magazine and awarded annually for the most excellent safety records, have been determined by the committee of award. One trophy was awarded to an anthracite mine in Pennsylvania, one to a bituminous coal mine in the same State, one to an iron-ore mine in Michigan one to a gypsum mine in Ohio, and one to an iron-ore opencut mine in Michigan.These trophies were awarded to the companies for having the smallest loss of time from accidents in proportion to the total number of man-hours worked by all employees at their mine or quarry. Honorable mention was awarded to each mine or quarry that ranked second, third, fourth, or fifth in its own ground and to all plants that were operated without a lost-time accident during the contest year. Eighty-four out of 337 plants that competed for the trophies were operated without an accident that disabled an employee beyond the day on which the accident occurred.Under the contest rules, all mines and quarries were divided into five groups, four of the groups representing different classes of underground mining operations (anthracite, bituminous coal, metallic ore, and nonmetallic mineral), and the fifth group repre-senting the quarrying or opencut mining of minerals whether metallic or nonmetallic. Twenty-seven mines were included in the anthracite group, 68 in the bituminous group, 52 in the metal group, 24 in the nonmetallic-mine group, and 166 in the quarry and opencut-mine group. The total of 337 mines and quarries was 26 more than the number of plants that completed the contest during the previous year.The committee of award which determined the winners of the contest was composed of seven members, all known throughout the mineral industry but not connected with the United States Bureau of Mines. The committee included W. H. Cameron, managing director of the National Safety Council; William Green, president of the American Federation of Labor; James F. Callbreath, Secretary of the American Mining Congress; T. T. Read, Vinton professor of mining of Columbia University and editor of Mining and Metallurgy; C. B. Huntress, executive secretary of the National Coal Association; A. J. Curtis, assistant to the general manager of the Portland Cement Association; A. T. Goldbeck, director of the bureau of engineering of the National Crushed Stone Association."

Jun 1, 1931

By William H. King

The property of the Cupric Mines Co. is situated in the San Francisco mining district, Beaver County, Utah, 21 miles westerly from Milford (fig. 1), the rail and supply center for the area. Scheelite mineralization was not discovered until 1941, although the occurrence of lead and copper minerals had been known previously. S. VI. Hobbs, of the Federal Geological Survey, examined the Cupric property in November 1941 and prepared topographic and geologic maps of the area. This work was supplemented by additional investigations in January 1943 and March 1944 (fig. 2).

Jan 1, 1949

By D. H. Desy

The Bureau of Mines has conducted research on the ignition of methane-air mixtures by sparks caused by frictional impact of aluminum alloys on rusted steel at typical coal mine fan speeds. The objectives were to establish the incendivity of aluminum alloys under these conditions, to investigate differences between aluminum alloys, and to evaluate substitute materials for the aluminum-steel combination. With a specially designed apparatus, three commercial aluminum casting alloys and a number of experimental aluminum alloys were tested for incendivity of the frictional impact against rusted steel in flammable methane-air mixtures. All aluminum alloys tested produced some ignitions. Of the experimental alloys, the harder alloys and those containing silicon tended to be more incendive than the others. With the normal experimental conditions, constructional steel, stainless steel, brass, and plastic did not cause ignition of methane-air mixtures in frictional impact against rusted steel. Some ignitions occurred with constructional steel at high speed in more flammable gas mixtures enriched with oxygen. From these findings, it is suggested that constructional material combinations other than the aluminum-steel combustion would minimize this inc endive hazard. A detailed description is given of previous research, and comparison is made with present results where appropriate.

Jan 1, 1975

By V. A. Marple, K. L. Rubow, B. A. Olson

"A virtual impactor personal aerosol sampler (VIPAS) bas been developed for use in diesel-equipped mines to collect size-separated samples or diesel exhaust and mine dust particles in the respirable size range. This sampler consists or three stages: a 10-mm cyclone, a 0.8- µm cutpoint virtual impactor and two filter cassettes. The large non-respirable particles are removed in a 10-mm cyclone. The respirable particles from the cyclone pass through a 0.8- µm cutpoint virtual impactor with the particles larger than and smaller than 0.8 JI.ID (mine dust and diesel exhaust particles, respectively) collected on two 37-mm filter cassettes. The sampling How rate is 2 L/min so as to be compatible with the standard respirable dust sampler and personal sampling pumps. INTRODUCTIONThe mining industry has been increasing its use of diesel-powered equipment in underground mines, especially in coal mines. With this increased usage has come an increased concern regarding the health effects associated with inhaling diesel exhaust particles since they are in the respirable particulate size range. A Mine Safety and Health Administration (MSHA) advisory committee directed MSHA to develop a sampling protocol for diesel exhaust particles to assess worker exposure (MSHA, 1988). In addition, the National Institute for Occupational Safety and Health (NIOSH) has recommended that ""whole diesel exhaust be regarded as a potential occupational carcinogen as defined in the Cancer Policy of Occupational Safety and Health Administration"" (NIOSH, 1988).Past work, with cascade impactors in both the laboratory and in underground coal mine studies, has shown that the diesel exhaust particles are primarily in the less than 0.8 µm aerodynamic diameter size range whereas the coal dust particles are primarily greater than 0.8 µm (Marple et al., 1986; Cantrell, 1987; Rubow and Marple, 1988; Rubow et al., 1990a, b; Cantrell and Rubow, 1991). This work has been jointly performed by the University of Minnesota and Bureau of Mines researchers over the last 8 years. Typical particle size distributions for a diesel-equipped coal mine and an all electric coal mine are shown in Figure l. Note that the particles in the < 0.8-µ.m mode are the diesel exhaust particles (seen only in diesel-powered mines) and the particles in the > 0.8-µ.m mode are coal particles (seen in both the electric-powered and diesel-powered coal mines). Chemical mass balance analysis was also performed on these two size fractions to determine the degree of particle cross-contamination in the two modes. This analysis showed less than 10% cross-contamination, i.e., in coal mines Jess than 10% of the diesel exhaust particulate was collected in the coarse fraction and Jess than 10% of the mine dust was collected in the fine fraction (Cantrell, 1987; Rubow et al., 1990a)."

Dec 1, 1996

By E. L. Garton

Michigan is becoming one of the important oil-producing States of the country. The amount of crude oil produced within its boundaries has increased from only 4,000 barrels in 19253/ to nearly 16 million barrels in 19935.4/ The Bureau of Mines method of crude-oil analysis and classification-indicates that the oils from the several producing fields are predominantly paraffin-intermediate-base, wax-bearing crudes. In general, they will yield 25 to 35 percent of highly paraffinic gasoline and about the t- me amount of kerosene and gas-oil combined, 7.2 to 15 percent of lubricating oil stock, and 20 percent of residuum with a carbon residue or about 6 to 7 percent. In addition, there appears to be some correlation between certain properties of the crude oils and both the geographical location and geological structure of the oil-producing areas within the State. These general conclusions are based on the analytical data presented in this report, which is one of a series of papers that record the general characteristics of crude oil from the many producing fields of the United States. This report discusses briefly the oil fields of Michigan and the characteristics of the crude oils produced from them. The analyses of 15 samples are given. These samples were obtained from 13 fields in 9 counties in the lower peninsula and represent crude oils produced from the Berea sandstone, Upper Traverse and Traverse limestones, and the

Jan 1, 1937