Search Documents

By David P. Lindroth

The Bureau of Mines has developed and successfully tested a hangup clearance module for use in clearing hangups in underground mine chutes and ore passes. The Bureau's tests showed that the hangup clearance module can be effectively used to clear mine hangups. Furthermore, it is believed that clearance using this module is quicker, safer, and more efficient than the method currently used. The hangup clearance module uses a ballistic disk explosive charge that can clear hangups located as far as 50 feet (15.2 m) from the position where the charge is detonated. Mine personnel can therefore set up the module and the charge it contains without being exposed to dangerous areas. This report describes the principles of operation of the module, provides data and drawings for its construction, and gives instructions for its setup and use. The report also summarizes the development of the module, briefly discusses preliminary and underground tests, and lists the current and potential applications of the hangup clearance module to underground mining.

Jan 1, 1982

By Barry W. Klein

The performance of the U.S. economy in 1977 was similar to that in 1976 which, in turn, had been a considerable improvement over 1974-75. In 1977 real gross national product (GNP) showed a similar, but some-what slower, growth pattern compared with 1976. Real GNP increased sharply in the first quarter of the year followed by smaller increases for the remaining three quarters. With only two exceptions, the monthly unemployment rate declined or remained steady throughout 1977, falling to a low for the year in December. The inflation rate in 1977 was slightly higher than in 1976, but the rate still remained far below that of 1974-75. Total U.S. output as measured by GNP in current dollars rose 10.8% in 1977. Real GNP in constant 1972 dollars increased 4.9%, and inflation, as measured by the implicit price deflator, rose 5.6%. In real terms, gross private domestic investment for residential structures increased 19.3% in 1977, only slightly below the 22.9% rise in 1976; State and local government expenditures increased 1.1 % in 1977; and personal consumption expenditures for services rose 4.5%.

Jan 1, 1980

By Peter G. Kovalchik, Rudy J. Matetic, Susan B. Bealko, Adam K. Smith

Overexposure to noise remains a widespread and serious health hazard in the U.S. service providing and goods producing industries. Excessive noise can lead to poor verbal communication and reduce the ability to recognize warning signals. These dangerous work conditions can also cause stress and fatigue. Occupational hearing loss is a permanent illness, with no recovery currently possible. Method: National Institute for Occupational Safety and Health (NIOSH) has recognized Noise Induced Hearing Loss (NIHL) as one of the ten leading work related diseases and injuries in the United States, and has emphasized its importance as one of the critical areas expressed in the National Occupational Research Agenda. Results: One of the most serious noise problems in the goods producing industries is the operation of continuous mining machines during underground coal mining. In order to minimize occupational hearing loss, noise hazards are “designed out” early in the design process. NIOSH is leading a national initiative called Prevention through Design (PTD) to promote this concept. This paper describes the quiet by design approach of a noise control that reduced noise exposures of continuous mining machine operators by 3dB(A) using the four functional areas of PTD, namely Practice, Policy, Research, and Education.

Oil from shales has long been a source of fuel in foreign countries; however, in the fuel economy of the United States this source is classed as a reserve for future needs. In fad, shale oil has never been produced here in quantities necessary to establish oil-shale utilization as a sustained industry. The first known resources of stored energy that man endeavored to utilize were probably wood and water, and from these he directly obtained heat and power, respectively. With the evolution of man came the search for and the development and use of other natural fuel resources, the series progressing through the solid, liquid, and gaseous fuels until today those of one type can be converted into another, depending upon the use for which they are intended. The most important fuels are those that appear naturally in the most concentrated, conveniently obtainable, and usable forms. With the discovery of each new and more concentrated fuel there has been an appreciable increase in the importance of and number of devices for converting these fuels into energy.

Jan 1, 1938

By D. G. RUNNER

Information Circular 6148R, " Selected Bibliography of Minerals and Their Identification ," was issued in June 1929 , revised in July 1937, and again in October 1938. The popularity of this circular , combined with the desire to make it more comprehensive , has occasioned the preparation of this compilation of references . Where possible , date of publication , publisher, current price , and number of pages are given, although prices are subject to change at intervals . The references are grouped under the following headings : minerals , gems , rocks , geology, geomorphology, engineering geology , prospecting, mining . engineering, microscopy, technical dictionaries , and miscellaneous . For ready reference, the authors ' names are arranged alphabetically under each grouping . This list is not comprehensive, but contains only those references in most common use and which are generally available in public college libraries .

Sep 1, 1949

By D. P. Lindroth

The thermal diffusivity above 298 K, up to 400 K and at pressures from ambient down to 10-10 torr was measured for the following six igneous rock types: tholeiitic basalt, obsidian, rhyolite, granodiorite, gabbro, and dunite. The thermal diffusivity data were obtained by the laser flash method. Extreme values range from a low of 5.3X10-3 cmF/sec for rhyolite at 383 K and 2X10-7 torr to a high of 13.4x10-3 crrf/sec for dunite at 298 K and 760 torr. Data are also included on a commercial fused silica, which was used as a standard.

Jan 1, 1974

By David C. Byrne

PURPOSE: Evaluate practical technological advances in level-dependent hearing protectors and inexpensive personal acoustic monitors. RESEARCH SUMMARY: The results of previous NIOSH research show that miners develop hearing loss much more quickly than nonoccupationally noise-exposed individuals and that miners experience a greater severity of hearing loss than would be expected for nonoccupational noise-exposed persons of the same age and gender. Using hearing thresholds at 4,000 Hz as an indicator, coal miners experience hearing loss 2.5 to 3 times greater than would be expected for persons not exposed to occupational noise. At age 50, 90% of coal miners and 49% of metal/nonmetal miners were found to have a hearing impairment. In comparison, only 9% of a nonoccupationally exposed control group had a hearing impairment at age 50. There are numerous barriers to the prevention of hearing loss among miners. In an effort to overcome some of these obstacles, this work was initiated to evaluate practical technological advances in level-dependent hearing protectors and inexpensive personal acoustic monitors. Experiments will involve analysis of this new technology under both laboratory and field conditions. Laboratory components will consist of controlled studies using an anthropometrically correct test fixture as well as human subjects to evaluate the adequacy/effectiveness of various hearing protective devices. Electroacoustical performance testing of new noise monitors will also be conducted in a laboratory setting. Subsequent field studies will determine the actual usefulness and practicality of the personal protective/monitoring equipment as used in different mining situations. It is anticipated that increased on-the-spot awareness of hazardous noise levels and the availability of better-suited hearing protectors will provide a degree of protection beyond what is currently attained in different mining environments. Therefore, the intent of this project is to identify and adapt new acoustical technologies and products that have a direct application to individual mine workers. With increased knowledge of these technological advances, a greater demand for similar devices will likely occur, which, in turn, will lead to a better understanding and awareness of hearing loss prevention methods throughout the mining community. The ultimate goal is for widespread integration of useful hearing loss prevention products and devices into the daily routines of miners

Jan 2, 2000

By Elmer E. Buban

A lightweight compressed oxygen rescue breathing apparatus (RBA) for rescue and recovery missions has been developed by Mine Safety Appliances Company under contract to the Bureau of Mines. The apparatus is a positive pressure, closed circuit system of 4 hours duration. The weight of the complete apparatus, including an optional cooler, is slightly over 30 pounds. Weight reduction over currently available RBAs is achieved through the use of lithium hydroxide for scrubbing C02 in place of conventional chemicals and the use of a composite glass fiber/ aluminum shell cylinder for oxygen storage in place of steel cylinders. Positive pressure is maintained in the breathing circuit at all times by applying a constant spring force to the breathing bag. The harness has been designed to reduce the work of the wearer by redistributing the weight of the apparatus to the wearer's hips.

Jan 1, 1981

By R. Stefanko

This Final Report covers the work performed for Contract No. H0377043, "Cables for Face Equipment" from August 1, 1977 to April 1, 1981. It reports the findings in three areas of research: cable protection, circuit-breakers, and high-voltage cable couplers. Laboratory and analytical studies have been conducted in the three areas to determine proper circuit-breaker settings, cable sizes, and coupler performance. Also, an extensive field-monitoring program was established to relate in-mine epxerience to laboratory findings. Further, various pieces of equipment was designed for laboratory testing, particularly in the area of cable reeling and unreeling.

Jan 1, 1981

By J. W. Faul

[The Bureau of Mines initiated an extensive research on coal-mine ventilation factors in 1922, large- scale tests being conducted in its experimental nine near Bruceton, Pa., over a period of two years. A comprehensive report an this work is in course of preparation, but in order to place the practical results before the mining fraternity immediately and in condenses form, the more important features will be presented in a number of short papers. The present report is the first of a series dealing with the resistance of coal-mine entries to the flow of air and considers only entries in which there are no obstructions other than the natural roughness of the ribs, roof, and floor.]

Jan 1, 1924

By David E. Fogelson

One model each of three different makes of portable displacement seismographs was calibrated on a shaking table capable of 5,000 pounds of force, Calibration tests were conducted in the frequency range of 5 to 200 c.p,s, and in the amplitude range of 0,002 to 0.05 inch peak-to-peak, The seismographs were tested under two mounting conditions: (1) The feet of the instrument were bolted to the shaking table, and (2) the feet were resting on emery cloth affixed to the table, The results of these tests show that, in the frequency range of 5 to 40 c.p,s, and for vibration levels less than 0.2 g, the magnification for all three instruments is constant with input level but varies slightly with frequency. For vibration levels greater than 0.4 g. and for frequencies greater than 40 c.p.s., the magnification of all three instruments shows large variations with frequency and amplitude of table motion.

Jan 1, 1962

MFIRE is a computer simulation program that performs normal ventilation network planning calculations, and dynamic transient state simulation of ventilation networks under a variety of conditions. The program is useful for the analysis of ventilation networks under thermal and mechanical influence. MFIRE simulates a mine's ventilation system and its response to altered ventilation parameters, external influences such as temperatures, and internal influences such as fires. Extensive output enables detailed quantitative analysis of the effects of the proposed alteration to the ventilation system Network simulation using digital computers has become widespread throughout the mining industry in recent years. However, as the sophistication of the simulator increases (MFIRE, for example), the complexity of input data requirements and interpretations of results requires more skill and knowledge from the users. Perhaps the most difficult part of using MFIRE is to construct the data set describing the mine's physical layout and its ventilation properties. The initial attempts to get the data set running often reveal unknown or ignored aspects of the mine's ventilation. MFIRE was written in Fortran 77 and compiled with Microway1 Fortran for the Intel 80386 based computers with a 80387 math co-processor. The source code is portable and available for users who wish to modify the source code to operate on other computers. This user manual describes the development of MFIRE, the input format and requirements, the output, common errors, fire parameters, and examples MFIRE application. Valuable reference material is included in the appendices. Knowledgeable users may skip directly to the PROGRAM INSTALLATION AND OPERATION section to begin using MFIRE immediately.

Jan 1, 1995

MFIRE is a computer simulation program that performs normal ventilation network planning calculations, and dynamic transient state simulation of ventilation networks under a variety of conditions. The program is useful for the analysis of ventilation networks under thermal and mechanical influence. MFIRE simulates a mine's ventilation system and its response to altered ventilation parameters, external influences such as temperatures, and internal influences such as fires. Extensive output enables detailed quantitative analysis of the effects of the proposed alteration to the ventilation system Network simulation using digital computers has become widespread throughout the mining industry in recent years. However, as the sophistication of the simulator increases (MFIRE, for example), the complexity of input data requirements and interpretations of results requires more skill and knowledge from the users. Perhaps the most difficult part of using MFIRE is to construct the data set describing the mine's physical layout and its ventilation properties. The initial attempts to get the data set running often reveal unknown or ignored aspects of the mine's ventilation. MFIRE was written in Fortran 77 and compiled with Microway1 Fortran for the Intel 80386 based computers with a 80387 math co-processor. The source code is portable and available for users who wish to modify the source code to operate on other computers. This user manual describes the development of MFIRE, the input format and requirements, the output, common errors, fire parameters, and examples MFIRE application. Valuable reference material is included in the appendices. Knowledgeable users may skip directly to the PROGRAM INSTALLATION AND OPERATION section to begin using MFIRE immediately.

Jan 1, 1995

By R. Stefanko

This first Annual Report covers the work on Contract No. H0377043 "Cable for Face Equipment", from August 1, 1977 to July 31, 1978. It reports the progress in the three areas of over-and short-circuit protection, cable ampacity research and cable couplers. Field trips have established many interesting facts related to circuit breaker settings and cable size. For example, the determination of cable sizes depends on the RMS duty cycle current determined by a particular piece of equipment, but the actual selection of the cable to be used is often a function of the maximum allowable circuit breaker instantaneous settings as specified in Title 30. In order to avoid nuisance tripping as a result of instantaneous starting current field, laboratory and analytical studies are being conducted to determine proper settings and cable sizes Also an extensive program has been established to monitor the performance of high voltage cable couplers and determine their modes of failure. Various equipments are being designed for laboratory testing, and an extensive reeled cable experiment is also under way.

Jan 1, 1978

By B. K. Shibler

During a research program to develop improved methods for recovering elemental sulfur and useful sulfur compounds from secondary source materials, the technical literature was searched for pertinent articles on processing methods. This report summarizes results of the literature survey and describes the more important processes that have been used or suggested for recovering sulfur and sulfur compounds from all non-Frasch sources. The bibliography presented represents a survey of the available English language literature on the subject through 1958, with particular attention focused on the period 1950 through 1958. Engineering Index and Industrial Arts Index were the principal guides used in the survey of this period. Chemical Abstracts was used to a limited extent to identify a few key foreign articles and patents. The Sulfur Symposium (4)4 published in November 1950 by Industrial and Engineering Chemistry includes a broadly representative selection of the literature up to 1949. Therefore, this reference was used extensively to locate and list pertinent articles on processing methods reported in the period prior to 1950.

Jan 1, 1962

By Frank J. Wiebelt

The Mohawk lead-zinc mining in San Bernardino County, Calif., was examined by D. W. Butnor, an engineer or the Bureau of Mines, at the request of Dunton, Ray, and Greenwood, leaseholders. Current operations were on a marginal economic basis, and government aid was sought in an endeavor to outline ore reserves so that production might be maintained.

Jan 1, 1949

By W. A. Young

To initiate this project a critical evaluation of the pre-sent phosphate mining industry in the Western phosphate field was conducted. Mines were visited, mine operators were interviewed and pertinent literature studied. Three phosphate mining enterprises were reviewed and mining cost estimates prepared. The report discusses the present state of phosphate processing, rock alteration and location. New ideas and concepts are proposed to improve the recovery of phosphate rock from the Phosphoria formation. The report evaluates two variations to the present phosphate open pit mining methods, which were developed to improve the economics of mining phosphate and to better accomplish necessary reclamation and accelerate the time for environmental recovery. A material handling system using conveyor haulage will eliminate the need for trucks. Terrace haulback utilizes safety benches to haul and dispose of waste in the mined out pit. Ore will be removed from the pit via an inclined, cable-supported mobile conveyor.

Jan 1, 1980

By Floyd D. Varley, C. M. K. Boldt

Toolbox training is often described as short, informal training conducted at a worksite by technically competent persons for the benefit of a work team. The key feature of toolbox training is the focus on a work team and what is important to that group in its workplace. Toolbox training conducted by peers can connect miners and establish the feeling that the hazard is a real threat to them. This feeling can bridge the gap between delivery of a safety message and behavioral changes that can prevent an accident. Toolbox training is a popular form of "maintenance" training that should not be used to teach a new skill. The 10- or 15-minute toolbox session is simply too short a time to teach or learn a new skill and test for skill development. However, the toolbox format is an excellent way to inform workers of changes in workplace rules, conditions, or hazards by bringing the discussion of change to the level of the work group and suggesting how a change will affect the way workers perform their jobs. Toolbox training should be structured to address a very specific hazard. That is, the hazard source should be identified and the effect of the hazard on the worker described. The temptation to discuss a safety subject in broad terms will result in an equally vague result. For instance, discussing "equipment guards" is inappropriate for a 15-minute training session. There simply is not enough time to cover all the hazards and their remedies. A more appropriate topic would be "placing guards on a conveyor return roller" or "hazards of cleaning a conveyor return roller." Each topic is concise enough to allow the trainer time to define a particular threat to the safety of miners and discuss ways to defend against that threat. The clearest way to a safe workplace is to identify hazards methodically and eliminate them. This cannot be done with sweeping, generalized training. Some best practices that will protect a worker from the hazard should be presented, and the hazard should be located at the specific worksite. Toolbox training is an opportunity for the work team to participate in learning and share experiences and knowledge, often through storytelling. Storytelling is an ancient form of passing along information in an entertaining way. It is entertaining because it draws the listener in with imagination and creativity. Stories told within work groups are a way for miners to exchange experiences in which they made mistakes that resulted in an accident or a near-miss and learned a valuable lesson. Thus, co-workers can learn from others without the pain or fear that accompanied the storyteller's learning path. To encourage these shared experiences, the people in the group must be comfortable with one another. Participation doesn't stop with listening to a near-miss story or informing the group of an unsafe work practice. Participation by sharing experiences, knowledge, and skills should lead toward action in changing the unsafe tool, practice, or machine (Wallerstein, 1992). This power to change is called empowerment. Empowered workers use toolbox training sessions to discuss a problem; direct their own knowledge, experience, and talents in the context of their work environment to solve the problem; and put into practice what they have learned by sharing (Baker, 1992). A worker is much more likely to implement changes they have contributed to creating than changes forced upon them. Toolbox training functions best when the group size is small (under 20) and composed of workers with similar job functions. While combining all workers on a shift or multiple shifts may be convenient, the level of participation will drop dramatically as group size increases and participants are less connected. Similarly, when the work group participants are from different job functions, keeping the materials relevant to the individual becomes more difficult. The role of management in the toolbox training system is to communicate among various groups so that all groups at a mine site are hearing the same message. In very small operations, combining work groups can be productive if the trainer can promote open discussions and lead the group to solutions that address the needs of all and not let one group or individual dominate the discussion. WHY USE NARRATIVE METHODS An effective communications tool is to use stories as a means of describing a hazard and its consequences. Historically, using stories to transfer knowledge between individuals of the same and different generations is well established. All good stories share the same elements required to communicate safety principles. Stories require a setting (the part of the workplace), a plot (the circumstances that lead to a hazard), the solution (best practices), the lesson (what can happen), and the result (what will be done to prevent the hazard) (Dennehy, 1999).

Jan 1, 2002

By J. G. Croeni

The titanium-iridium alloy system was investigated to determine whether alloys of this system would merit further development as control-rod material for nuclear reactors. A study was made to determine the titanium-iridium phase diagram by using melting-point, thermal analyses, X-ray diffraction, dilatometric, electrical resistivity, and metallographic techniques. The titanium-iridium alloy system was investigated between 500° and 2,400° C. Results indicate the formation of two intermetallic compounds, Ti3Ir rind TiIr3, and one intermediate solid solution centered about the 50 atomic percent iridium composition. A eutectic reaction occurs at 1,475° C, and 19 atomic percent iridium. The Ti3Ir decomposes peritectically at 1,520° C. The intermediate solid solution exhibits a maxima of 2,140° C. at 50 atomic percent iridium. This phase is also believed to undergo an order-disorder transformation at 1,750° C. Another eutectic reaction takes place at 2,000" C. and 60 atomic percent iridium. The compound TiIr3 formed at 75 atomic percent iridium decomposes peritectically at 2,115° C. Further increases in iridium content result in the formation of an iridium-rich terminal solid solution. Information obtained below 900° C. in titanium-rich alloys indicates that iridium acts as a beta stabilizer in titanium, and the authors believe that a eutectoid decomposition of beta-titanium occurs near 500° C. and 10 atomic percent iridium.

Jan 1, 1962

By Maria I. De Rosa

Table 37 and figure 13 show the number of fires and fire injuries for surface stone mines by state during 1990-2001. Table 37 also shows the injury risk rates, employees' working hours, and lost workdays. In all, 96 fires occurred in 31 states and 1 fire occurred in Puerto Rico. Sixty-eight of the fires caused 67 injuries and 1 fatality (including 6 fires and 5 injuries involving contractors). The yearly average was eight fires and 5.6 injuries. The Ewhr value was 689 x 106 hr (Irr = 0.02), and the LWD value was 7,399. Indiana had the most fires (eight fires and four injuries), followed by Georgia (seven fires and seven injuries) and Pennsylvania (seven fires and five injuries). Of these states, Georgia had the highest injury risk rate value (Irr = 0.058). Table 38, partly illustrated in figure 14, shows the number of fires, fire injuries, fire fatalities, risk rates, employees' working hours, and lost workdays by time period. The number of fires and fire injuries show an increase during the second period followed by a decrease during most of the remaining periods. Employees' working hours increased during most of the periods. The In values follow patterns similar to those shown by the injury values. Tables 39-44 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 15 shows the major variables related to fires for 1990-2001. Table 45 shows the number of fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004