Search Documents

By C. E. Augustine, P. Nicholls

"INTRODUCTION A layer of soot on the heating surface of a boiler decreases efficiency because it increases resistance to the flow of heat, with the result that the heat transfer to the water is lower and the temperature of the flue higher than they would be if the surface remained clean. The percentage of reduction in heat transfer depends on the position and area of the sooted. The percentage of reduction in heat transfer depends on the position and area of the sooted surfaces, the thickness of the most, until the percentage of the total heat absorbed by those surfaces when clean; thus it will vary with the type of boiler and in particular with the ratio of the area of the convection heating surface to the total area. Medium-size and large boilers usually are equipped with soot blowers, and tests have been published giving the increase in efficiency resulting from removal of the soot. Fuel savings up to,8 percent have been reported, but 4 to 5 percent is probably more conservatives. However, these savings may not be due wholly to a reduction the thermal resistance of the surfaces but may be due partly to improvement in the combustion because of better draft or more uniform flow of the gases. In addition, the deposits on the surface of boilers include as a clinker, and as the size of the boiler and the rate of burning increase very little or none will be soot.There are no corresponding test data on small boilers operated at low rates of burning. In stall boilers, deposits are much thicker, and it might be expected that the reduction in efficiency would be greater; in fact, statements have appeared suggesting that the decrease may be as high as 50 percent. This investigation was undertaken because the Bureau frequently receives requests for authoritative information on the effect of soot in small and other heating boilers."

Feb 1, 1935

By B. W. Haynes

This Bureau of Mines report describes the laboratory processing of manganese nodules and the results of tailings characterization obtained during the cooperative program with the Department of Commerce's National Oceanic and Atmospheric Administration (NOAA) and the Bureau. Five technically feasible first-generation nodule processing methods were operated at bench scale to generate sufficient tailings and slags for physical and chemical analyses. A description is given for the laboratory operation of the individual unit operations of each process. The laboratory-generated tailings and slags were tested for physical properties, mineral content, elemental and ion content, and leachability for all five processes. The results of leachate testing using the Environmental Protection Agency extraction procedure (EP) toxicity test, the American Society for Testing and Materials shake extraction test, and the EPA-U.S. Army Corps of Engineers seawater elutriant test showed very low to negligible leaching of metals from the tailings and slags. Results of the EP toxicity test demonstrated that the wastes are nonhazardous as defined in the Resource Conservation and Recovery Act (Public Law 94-580).

Jan 1, 1985

By D. L. Pool

To increase metal recoveries and to minimize pollution by improved extraction technology, the Bureau of Mines investigated a hydrometallurgical technique to recover copper, lead, nickel, and cobalt from lead smelter mattes. The metals were converted from insoluble sulfides to soluble chlorides using a HCI-CI2-02 leaching system. Parameters studied in a 50-gallon, glass-lined reactor were the ratio of hydrochloric acid to chlorine, chlorine consumption per pound of matte, oxygen reaction pressure, and temperature. The matte material used contained, in percent, 19.7 Cu, 52 Pb, 2.9 Ni, 1.5 Fe, 0.38 Co, 0.19 As, 0.41 Zn, and 0.12 Cd. Extraction of Cu, Pb, Ni, Co, and Cd ranged from 92 to 98 pct, with concomitant extractions of Fe and As of <0.1 pct. The Cu and Pb were recovered as electrowon metals, while the Ni, Co, and Cd were recovered as mixed hydroxides.

Jan 1, 1981

By David A. Summers

The use of high pressure fluid cavitation is investigated as a means of breaking an ore into its constituent grains. This Cavitational Rock Dissagregation (CRD) is found to be possible and effective in breaking down galena ore, both in sandstone and dolomite host material. The technique did not work as well in comminuting and cleaning oil shale, because the cavitation drove the oil into emulsion with the water. The presence of dominant bedding in the rock also caused preferential breakage to these lines, rather than to the individual grain boundaries. This problem was also encountered in tests on igneous ore where weakness plants of the overall ore proved weaker than the boundaries of the individual grains. It was found that the prevailing expression of cavitation erosion dependence on pressure was not absolutely valid. In contrast it was found that CRD is much more sensitive to jet flow diameter, and when this was recognized it was found possible to erode rock with compressive strength of up to 350 MPa with operating jet pressures of 10 MPa.

Jan 1, 1982

By Michael S. Wieland

The work-principle method was developed for theoretically resolving toxic fumes from non-ideal charge formulations. The whole description of a wanted process refers to macroscopic changes resulting from removing and imposing constraints that work one at a time to chronologically render trajectory terminal (key) states. The trajectory resolution utilizes a thermodynamic quasi-potential or negative work function, and numeric results require some appropriate standard thermodynamic (equilibrium) reaction code TDRC. The underlying method is unable to restrict reactions, tailor the work output or resolve states within the trajectory transitions, so the trajectory terminology is used somewhat figuratively. The work-principle model has the working fluid (reaction material) interacting with a tremendous reservoir (chamber air and walls), while forecasting the work performed upon a mechanical agent. Within the underground test chamber, the widening fume zone undergoes a decline in temperature, a reduction in reaction rates, resulting in out-of- equilibrium circumstances at the Q*-point, representing the measurement state. Rather than coping with the hard issues of non-equilibrium, the toxic fumes are resolved numerically for the Z-point, rendered by a zero-net- interaction energy constraint. Though other techniques require complex equation-of-state EOS for the whole trajectory, the work-principle formulation eludes the issue, requiring an EOS that works just for the terminal-state. Under the circumstances, the Z-state is reconcilable with the ideal-gas domain, and relevant TDRC results yield the restricted state in a numerical way for different charge formulations. The work principle makes it hard to remedy or to tamper with the resulting Z-point fumes: non-macroscopic trajectory readjustment is forsaken, terminal states are results rather than stipulations, and resetting the EOS formula constants would be ineffectual. Though the non-equilibrium portion remains unresolved, it is noteworthy that the work principle rigidly fixes the Z-state, thereby reducing the uncertainty for rendering reaction-rate models characterizing the non-equilibrium Z-Q* transition. Though more refinements are needed, some Z-point fume results are included to illustrate the threshold (minimum) resolving capacity of the work- principle formulation.

By Robert W. Freedman

Vacutainers are employed by the Bureau of Mines and the Mining Enforcement and Safety Administration for sampling mine air and other atmospheres containing fixed gases, low-molecular-weight hydrocarbons, and products of combustion. Tests were conducted to study shelf life of evacuated samplers prior to sampling and also to check the stability of sampled gases prior to analysis. An unexplained phenomenon, slow accumulation of carbon monoxide in evacuated samplers, occurred after a few weeks&apos; storage; levels were low but increased with time and could pose a problem for critical applications. Accordingly, attempts to halt CO release by additional means of treatment were made, and storage at low temperature was found to be effective.

Jan 1, 1978

By E. S. Burnett

The temperature entropy (T, S) chart? of thermodynamic properties of nitrogen herewith presented is a complete (1949) revision and a considerable extension of similar charts prepared by the author for use of the helium section of the Bureau of Mines about 25 years previously on the basis of inadequate data then obtaining. During the interval since that early effort, much experimentally determined information on nitrogen properties and behavior has been published, which now permits a more nearly accurate layout and more extensive charting of these relations.

Jan 1, 1950

By J. A. Stampe

In connection with its investigations of strategic minerals in the United States, the Bureau of Mines ran magnetic surveys totaling more than 533,000 linear feet at 30 deposits of magnetite in northern New Jersey. These deposits occur in a belt of granitic gneiss and in limited areas of limestone. The ore consists of magnetite accompanied by score of the following minerals: Hornblende, augite, apatite, feldspar, biotite, calcite, garnet and pyrolusite. Results of these investigations are being presented in two reports of which this is the second. The first paper, Certain. Magnetite Deposits in New Jersey, by A. L. Neumann and McHenry Mosier, was issued in April 1948 as Report of Investigations 4225.

Jan 1, 1949

By Warren E. Morrison

Demand for energy in the United States in 1965 was stimulated by the continuing expansion of the economy. A gain of 5.9 percent in gross national product for the year was accompanied by a 4.4-percent rise in energy consumption. Domestic energy resources met about 93 percent of the nation&apos;s requirements. The remaining 7 percent consisted of imported fuels, mainly of crude petroleum and residual fuel oil. The major fossil fuels-natural gas, crude petroleum, and coal, in that order-contributed 96 percent of all commerical energy utilized, with the balance of 4 percent being primary electricity from hydropower and nuclear power plants. Production was up for all of the major mineral energy resources in 1965, with the single exception of anthracite, output of which continued to decline. Bituminous coal output for the year was 512 million tons; marketed production of natural gas, 16,039 billion cubic feet; and crude petroleum output, 2,848 million barrels. Among the secondary products processed from primary energy resources, the most significant gains were in coal carbonized for coke which increased 6.7 percent to 95 million tons, and in the output of liquefied gases from natural gas which rose 4.8 percent to 11,257 million gallons (268 million barrels). Within the latter category, the off? take for petrochemical feedstocks continued to rise at a very rapid pace.

Jan 1, 1967

By James R. Boyle

The value of mineral production in-creased 13% in 1977. Nearly all commodities registered an increase in production and value, continuing a trend that started in 1976. In addition, practically all commodities registered an increase in unit value. Alabama led the Nation in the production of crushed marble, was second in bauxite and scrap mica third in kaolin and oyster shell, and fourth in bentonite, dimension marble, and fire clay.

Jan 1, 1981

By Paul M. Tyler

This paper presents one of a series of digests of foreign mining legisla- tion and court decisions that is being prepared in advance of a general report relative to the rights of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the laws of Switzerland has been prepared from the best information available in ashington, but is released subject to correction and amplification, if necessary, by the proper American diplomatic and consuler officers, to whom it is being referred through the courtesy of the Department of State. Sitzerland is a small country in which little mining is done, yet it has a voluminous body of mining legislation. There are two salt-mining districts in Switzerland; that at Bez, Canton of Vaud, belongs to the Canton but the deposit is worked by a private company; and those at Schweizerhalle, Rheinfelden and Ryburg are worked by a joint stock company formed by the Cantons interested. Iron ore is mined at Gonzen, Canton of St. Gallen, and large beds of gypsum are worked, mainly for domestic consumption. In general, however, although many kinds of minerals are said to have been found in Switzerland, mining operations are irreguler end relatively unimportant. Even during the world war only about 2,500 persons were employed in mining establishments and most of these were in under round stone quarries. On the other hand, the republic comprises 22 Cantons, of which 3 are divided, making 25 units, and in the absence of generel Federal legislation, each of these units virtually has its own distinct mining la Under these circumstances, it is obviously inadvisable to review the mining lars of Switzerland in the same detail as those of other countries which Lave been digested in this series. For the lars of individual Cantons, as well as for a more comprehensive summary of the Swiss legislation as a whole, the reader is referred to a recent German publication." Many of the statements in the present paper can be traced to this source. Acknowledgment is also made of the brief analysis published by anot..er German authority..

Jan 1, 1933

By John Gross

The modern practice of grinding ores so that often 80 per cent or more of the product is finer than 200 mesh makes it desirable to supplement sieve sizing so as to extend considerably the range of sizing. Moreover, the fact that the material finer than sieve size represents the major part of the work done in grinding emphasizes thick need in can investigation of crushing efficiency. A method based on the settling rate of particles in grater appeared to be most practical for sizing; finely ground ores. There are two possible methods of utilizing this principle: one based on free settling or sedimentation; and the other on separation by means of a rising; current of water, or elutriation. In sedimentation, mechanical entanglement causes material at the start to settle in a mass, and this persists throughout. As this feature is largely eliminated by elutriation, which permits a comparatively clean separation of the various sizes, the elutriation method was adopted.

Jan 1, 1929

To design an apparatus that advances the state of the art in gas content testing equipment. The goal of the design is to incorporate improvements in testing sensitivity/accuracy, durability, and ease of operation over existing equipment. It is also desirable for the new design to successfully perform gas content determinations of multiple chemical species from a rock sample.

Jan 1, 1999

By Charles L. Kimbell

Bulk carriers, freighters, and tankers are the three classes of marine vessels engaged in transporting mineral commodities. However, vessels in each of these categories are not devoted wholly to mineral commodity transport. Bulk carriers move agricultural products as well as crude minerals and mineral fertilizers, as ore/bulk/oil carriers also do. Freighters, owing to their great variety, can be devoted wholly to hauling mineral products or wholly to moving nonmineral goods, as well as carrying mixed mineral and nonmineral cargoes. They include general cargo carriers, full containerships, partial containerships, roll-on/roll-off ships, and barge carriers. Tankers, although largely engaged in moving crude oil and refinery products, also transport liquid chemicals, molasses, wine, liquefied natural gas, and other fluids. Although physical characteristics of vessels, such as sue, draft, crew requirements, and type of propulsion system, as well as fuel costs, have an undeniable influence on shipping industry performance, problems of and changes in the quantity and quality and types of material moved also significantly affect the shipping sector of the world economy. Unfortunately, comprehensive data in this regard are not available.

Jan 1, 1992

By Jeff Kravitz, John Kovac, Wayne Duerr

Since 198 1, Federal mining law has required every miner working in underground coal mines to have a self-contained, self-rescuer (SCSR) available for use in emergencies. Some miners that have escaped from fires using SCSR&apos;s have reported that they had to remove their mouthpiece to talk during escape, thus compromising the protection afforded by the SCSR. If miners are in thick smoke during an escape, they may have trouble if they become separated from their group. The visibility can be so poor that separation can occur at very short distances. To address this problem, two-way, FM radios were built into the SCSR to improve the ability to communicate should the miners be separated over relatively short distances. The SCSR prototypes built and used in testing included both two-way radios and improved mouthpieces. Comparison studies were conducted using combinations of the new and old mouthpieces, and trials using the radio or not using the radio. Subjective judgments indicate that communication ability was significantly improved using the prototype devices. Communication problems have been encountered with teams using standard voice- powered communications systems. Mine rescue teams perform rescue and recovery work under extremely hazardous conditions, life lines are a standard part of mine rescue team equipment. Leaky feeder and quasi-leaky feeder life line communications systems provide significant improvements over standard systems. These improved systems allow all members of the team to communicate with each other and their base of operations. These innovations will significantly enhance the safety of mine rescue operations.

By Andrew B. Cecala, Edward D. Thimons

The Bureau of Mines has successfully tested a method to simulate methane (CH~) flows from face areas through the returns of noncoal mines. This technique&apos; involves releasing a small quantity of tracer gas at a working area and sampling for that gas downstream in the re- turn airways. By measuring the dilution of the tracer gas, the dilution of any volume of CH4 released at the face can be calculated. This information is useful in selecting locations for CH4 monitors and in deciding the necessity for permissible equipment in the returns.

Jan 1, 1984

By G. W. Jones

During the course of an investigation by the Bureau of Mines into the causes, behavior, and control of anthracite-mine fires, it was observed that the carbon monoxide disappeared from a sealed fire area much more rapidly than could be explained on the basis of leakage of gases. Two suggestions were offered for this high rate of disappearance: (1) That the carbon monoxide, was oxidized at temperatures below 150° C. by either the anthracite or its ash (tests on many anthracites have shown that at temperatures above 150° C. carbon monoxide is liberated in the oxidation products when air is passed through it); (2) that the carbon monoxide was oxidized by micro-organisms present in the sealed area.

Jan 1, 1939

By C. E. Jordan

Under its program of advancing minerals technology, the Federal Bureau of Mines has invented a laboratory apparatus for continuous separation of minerals based on differences in dielectric properties. The separator consists of a rotating drum electrode and a wire screen electrode positioned 3 mm apart. A high voltage applied across the electrodes that are immersed in a dielectric fluid produces a high-gradient electric field. The high-dielectric-constant (K) minerals are attracted to and conveyed through the separator by the rotating drum electrode, while the low K minerals settle through the screen electrode. Several design and operating parameters, such as electrode configurations, the dielectric liquid and its dielectric constant, electrical voltage and frequencies, feed rates, and particle sizes were studied. In addition, 28 different mineral mixtures were tested with the dielectric separator. In typical tests, a sample of rutile and quartz gangue containing 10-percent rutile was concentrated to 62-percent rutile with 94-percent rutile recovery. A second-stage dielectric separation of the rutile concentrate produced a 92-percent-rutile concentrate. The overall rutile recovery for the two-stage dielectric separation was 86 percent.

Jan 1, 1980

Improve the safety of mine workers by developing a means of forecasting impending roof falls in underground mines. Approach The Bureau of Mines, through in-house and contract research, has developed the Roof Fall Warning Device. This battery-operated, portable electronic system forecasts roof falls by detecting and interpreting high-frequency rock noise, The technology has shown potential for detecting stress-related failures in a variety of underground environments. How It Works All geologic materials produce high-frequency acoustic emissions when they encounter an increase in stress. These ultrasonic frequency range events ( >20kHz) are well above the audible range of human hearing, very small in amplitude and duration, and can only be detected with sophisticated electronic equipment.

Jan 1, 1990

By J. E. Chilton, Jr. Dubaniewicz

Many mines rely on toxic gas sensors to help maintain a safe and healthy work environment. This report describes a prototype monitoring system developed by the U.S. Bureau of Mines (USBM) that uses light to power and communicate with several remote toxic gas sensors. The design is based on state-of-the-art optical-to-electrical power converters, solid-state diode lasers, and fiber optics. This design overcomes several problems associated with conventional wire-based systems by providing complete electrical isolation between the remote sensors and the central monitor. The prototype performed well during a 2-week field trial in the USBM Pittsburgh Research Center Safety Research Coal Mine.

Jan 1, 1995