Search Documents

[ ]

Jan 1, 2011

By E. Rupprecht, J. Volkwein, K. Cashdollar, R. Gürtunca

The National Institute for Occupational Safety and Health (NIOSH) mining research program at the Pittsburgh Research Laboratory (PRL), includes the areas of coal mine dust control and monitoring, and explosion prevention. One very important project at PRL is development of a continuous recording person-wearable respirable dust monitor. This Personal Dust Monitor (PDM) is a respirable dust sampler and gravimetric -equivalent analysis instrument that is part of a belt-worn mine cap lamp battery unit. Prototypes were successfully tested in the laboratory and in four underground coal mines. The PDM testing demonstrated that it was convenient to wear and use, robust, and provided accurate and timely data. NOSH is also conducting research in the program area of coal mine explosion prevention, suppression, and mitigation. Aspects of this research program include: full scale explosion research, laboratory scale research, frictional ignition of methane, mine ventilation seal construction, prediction of coal mine methane emissions, mine monitoring systems, flame cutting and welding operations, spontaneous combustion, and emergency preparedness.

By E. R. Spencer, D. R. Babich, L. A. Alcorn, A. K. Smith

Noise is one of the most pervasive health hazards in mining. A compilation of Mine Safety and Health Administration (MSHA) noise survey data for fiscal year 1990 shows that approximately 40% of the total samples taken for longwall occupations exceeded the Permissible Exposure Limit (PEL) of 100% (Gigliotti et al., 1991). To effectively determine worker noise exposures on longwall coal mining systems, it is necessary to provide accurate baseline measurements for these mining systems. This research was designed to develop measurement methods and test procedures for identifying noise sources that are major contributors to the underground noise exposure of longwall coal mining system workers. The measurement system that was used to analyze the noise sources around a stageloader used stationary dosimeters in a documented repeatable pattern to record the sound pressure and dose levels. A time-motion study of the cutting cycle and stageloader operator’s work cycle was done to correlate the sound levels at measurement locations and the resulting operator’s daily dose with significant noise events. Results from the underground measurements show that the highest sound levels recorded were at the stageloader discharge segment and tailpiece controls, where sound levels remained about the same throughout the test.

In Maryland, coal mining is confined to Garrett County and the western portion of Allegany .County. Terrain in both counties is predominately level with rolling hills; state law prohibits surface mining in steep slope areas. The Conemaugh and Allegany geologic formations contain five major minable fields or basins. These include: Upper Youghiogheny, Lower Youghiogheny, Castleman, Upper Potomac, and Georges Creek. Maryland's coal reserves are estimated to exceed one billion tons. Approximately 490 million tons of bituminous coal are considered recoverable using conventional mining methods. After World War 11, deep mining declined in Maryland, and by 1977 surface mining accounted for 91 percent of the total production. Since then, production at underground mines has recovered, accounting for 69 percent of the coal production in 1991. Maryland's permanent regulatory program was fully approved February 18, 1982. Its Abandoned Mine Land Program was approved June 16,1982.

Jan 1, 1992

By J. R. Allsup

In cooperation with the Division of Advanced Automotive Power Systems Development, Environmental Protection Agency, the Bureau of Mines studied a conventional spark-ignition engine as a prime mover for use in a hybrid system. The study involved both steady-state and transient engine operation with ignition timing, air-fuel ratio, exhaust gas recirculation, oxidizing type catalytic converters, engine speed, and power output as variables. Data were obtained from two 1971 model 350-cubic-inch-displacement engines mounted on engine dynamometer stands. When the hybrid engine was operated with an oxidizing catalyst at power output levels required for a 4,000-lb curb weight hybrid vehicle, carbon monoxide and hydrocarbon emissions could be reduced to approximately 2.0 grams and 0.3 gram per brake horsepower-hour, respectively. With exhaust gas recirculation, oxides of nitrogen emission levels could be reduced to approximately 1.2 grams per brake horsepower-hour.

Jan 1, 1974

By John C. Gagliardi, Walter K. Utt

The U.S. Bureau of Mines, in cooperation with Carter Mining Co., conducted vibration tests of four off-road vehicle seats. The purpose of the tests was to determine which seat provided the best vibration attenuation under laboratory conditions. Laboratory tests were constructed to simulate the mining vibration environment within the limitations of the test equipment. The acceleration test levels and corresponding response of the seats were low compared to IS0 2631's fatigue-decreased-proficiency time limits. Two of the seats employed mechanical suspensions and two seats employed air suspensions. The seats were tested using a 22,241-N (5,000-lbf) electrodynamic shaker. Mechanical suspension seats were tested with various preload-to-mass ratios (PMR's) and cushion densities. Air suspension seats were tested with various air pressure levels and seat cushion densities. Air suspension seats provided good vibration attenuation if pressurized greater than 552 kPa (80 psi). Mechanical suspension seats' attenuation performance decreased if the PMR exceeded 9.8. Seat cushions of lower density provided less vibration damping.

Jan 1, 1993

By S. P. Polack

"INTRODUCTION The purpose of this circular is to correlate the information obtained during personal investigations at the sites of four rock tunnels in the process of construction and information obtained from the records and personal views of the constructors of two other tunnels that were not visited during the, excavation phase of construction and to present this information for the benefit of those who contemplate future construction of rock tunnels.Modern mechanized coal mining requires better, safer, properly alined haulageways and beltways; consequently, better understanding of tunneling methods by coal-mining men will be necessary. The possibility of future high-speed haulage systems utilizing rock tunnels in the more solid rock strata above or below the coal beds must not be discounted. In the past, tunnels have been driven for use in draining and unwatering inundated coal mines. At present, the need for such tunnels is very evident in some parts of the coal-mining regions, notably in the Pennsylvania anthracite fields, and studies along these lines are in progress. The average coal-mining man has little time or opportunity to visit tunnels while they are being exca-vated; therefore, it is hoped that this information will assist him in constructing tunnels safely if he is required to do so in the future.The tunnels described herein differ in size, shape, usage, and, in many instances, in their geological aspects. Full-face, heading and bench, and pilot-tunnel, and enlargement methods of excavation were utilized.The roof-support methods show diverse designs and materials of construction to suit each purpose and condition. The superiority of steel roof support over wood is demonstrated beyond doubt and is shown clearly in the photographs included in this circular.The illustrations (photographs taken by the U. S. Bureau of Mines, the U. S. Corps of Engineers, and others) show many of the necessary steps taken during the excavation and the erection of roof support in tunnels under construction."

May 1, 1950

By David E. Siskind

The Bureau of Mines has studied the fracturing produced in the vicinity of large-diameter blastholes in Lithonia granite. Cores were taken from the vicinity of AN-FO production blasts and examined using a total of seven laboratory and field measurement techniques to delineate zones of damage and evaluate the effectiveness of the seven diagnostic tests for fracture-state determination. Laboratory measurements of acoustic pulse velocity, porosity, permeability, compressive strength, and Young's modulus indicated the extent of fracturing with the acoustic techniques providing the best means of distinguishing between fractured and unfractured core. A severely fractured zone was found to extend approximately 25 inches (64 cm) from the center of the 6-l/2-inch blastholes, equivalent to 8 blast-hole radii. A second zone, characterized by a lesser degree of fracturing extended from 25 to 45 inches (64 to 114 cm) or 8-to l4-blasthole radii. Beyond 45 inches (114 cm) the rock was undamaged.

Jan 1, 1974

By J. Douglas Causey

In 1984, at the request of Bureau of Land Management, the U.S. Bureau of Mines studied the 13,730-acre Burnt Lodge (MT-065-278) Wilderness Study Area (WSA) in order to evaluate the mineral resources. The WSA is located in Phillips and Valley Counties, MT, about 55 miles south of Malta adjoining the Charles M. Russell National Wildlife Refuge. It is underlain by near horizontal sedimentary beds of the Hell Creek Formation, Fox Hills Sandstone, and Bearpaw Shale. No mines or prospects were found in the WSA. Bentonitic beds were examined, but are generally less than 1 ft thick and, except where exposed, are deeply buried. Kaolin-bearing sandstone in the Colgate Member of the Foxhills Sandstone was sampled and may have potential for use in structural clay products. However, remoteness and inaccessibility of the area make it unlikely that the material could be economically extracted even though some of the material is marginally useful.

Jan 1, 1985

By Larman J. Heath

Wellbore enlargement was tested using hydrazine hydrate in a gas-storage well in Ohio to increase the well productivity. The wellbore was to be enlarged by chemical disaggregation of the sandstone adjacent to the wellbore. Productivity immediately declined 49.1 percent and gradually declined to zero in 7 months. A down-hole camera survey showed a white-to-gray precipitate covering the entire wellbore surface. The precipitate was chemically analyzed and identified as mostly carbazic acid, a hydrazine derivative of carbonic acid. Formation of this precipitate was not anticipated; this viscous sub-stance caused the gradual loss in productivity of the well. The wellbore was not enlarged. Laboratory tests were run to determine what clay stabilization measures could be taken in sandstone cores to prevent clay swelling and particle migration caused by hydrazine hydrate. Normal clay stabilization methods did not prevent the virtually complete loss in permeability to hydrazine hydrate. Other laboratory tests using natural gas diluted with small amounts of carbon dioxide confirmed the ease with which carbazic acid could be formed in a hydrazine hydrate-saturated environment within and adjacent to the wellbore.

Jan 1, 1970

By Karl C. Dean

The Bureau of Mines studied the precipitation of copper from dilute acidic sulfate solutions using shredded automobile scrap in a rotary drum. The tests established that the scrap in the rotary drum precipitated copper faster and more completely than shredded, detinned, tinplate scrap in a launder, with comparable iron consumption. Although power is required to rotate the drum, the faster precipitation and continuous recovery of cement copper are advantages of the tumbler method. Cost evaluation indicates that the rotary drum method, which uses relatively low-cost and readily available shredded automobile scrap, is competitive with the launder method, which uses relatively high-cost shredded tinplate scrap or detinned shredded cans.

Jan 1, 1968

By Brian G. White

The Coeur d'Alene Mining District of northern Idaho is remarkable for its number of large ore bodies and for the amount of its historical production of lead, zinc and silver (Fig. 1). Since veins were first discovered in 1884, more than 127 Mt (140 million st) of ore have been produced from narrow, high-grade veins. Mining continues at the Lucky Friday, Galena and Sunshine mines (Fig. 2). All have been in production for decades. At these mines, more efficient mining and exploration techniques have reduced costs while adding significant new reserves. Even the old Bunker Hill Mine, where ore was first found in 1875, continues operation on a limited basis, partly involving production of world-class pyromorphite specimens. Until recently, the Coeur Mine was also a profitable silver producer. Other large producers have included the Star-Morning, Hecla, Page, Standard-Mammoth, Hercules and Gold Hunter mines (Fig. 2). The first deposits were discovered by prospectors who spilled over from the Murray gold mining district, 24 km (15 miles) to the north. The Bunker Hill Mine was founded the year after the first veins were discovered. Bunker Hill has now operated for more than 100 years. Production includes 2.3 Mt (2.6 million st) of lead, 1.1 Mt (1.2 million st) of zinc and 4.1 kt (132 million oz) of silver. Total district production through 1996 (Springer, 1997) amounted to 7.3 Mt (8.1 million st) of lead, 3 Mt (3.3 million st) of zinc, and 34.5 kt (1.109 billion oz) of silver. This record establishes the district as the largest recorded producer of silver in the world, while also yielding major quantities of lead and zinc. Only Potosi, Bolivia, may have produced more silver, although records are unclear. Despite the district's longevity, historic production and current activity, the published literature on the district lags behind with regard to recent concepts of district geology. The most recent comprehensive US Geological Survey (USGS) bulletins (Hobbs et al., 1965; Fryklund, 1964) are dated. Much research in the last half century has been short-lived or geographically restricted because the district is large and its geology is complex - and even this research tends to remain unpublished. Thus, it has been difficult for in- [ ]

By Edward L. McHugh

The study area, which comprises 11,500 acres, includes the 9,610-acre Whitewater Wilderness Study Area, in the California Desert Conservation Area, 15 miles northwest of Palm Springs, CA. The U.S. Bureau of Mines evaluation of mineral resources is based on examination of prospects and mineralized areas during the spring of 1981. The Whitewater study area is mainly underlain by granodiorite to quartz diorite and their gneissic equivalents in an igneous-metamorphic complex. Late Tertiary sedimentary and volcanic rocks locally overlie the crystalline complex in the eastern part of the study area. The study area lies between branches of the San Andreas fault system.

Jan 1, 1986

By Arnold M. Lansche

DOMESTIC OUTPUT of white arsenic, As2O3, was derived entirely as a byproduct of smelting arsenic-containing copper ores by The Anaconda Company at Anaconda, Mont., and American Smelting and Refining Company at Tacoma, Wash. Arsenic metal was not produced. Consumption, and Uses.-Most of the white arsenic produced in 1964 was consumed in manufacturing lead and calcium arsenate insecticides. In the 12 year period since 1951 the production of lead arsenate insecticide has varied between 7,800 tons and 4,900 tons, indicating that lead arsenate has maintained its position in competition with organic insecticides.

Jan 1, 1965

Develop technology for preparing thick corrosion-resistant coatings and electroforms of iron-chromium-nickel alloys. Approach To reduce the United States' dependence upon foreign sources for supplies of strategic and critical metals such as chromium, cobalt, and nickel, new technology must be devised to conserve these valuable commodities. One approach being investigated by the Bureau of Mines is the use of a modified-aqueous-electrodeposition method to prepare thick (-25 µm), complex alloy coatings (e.g., stainless steel composition) with properties similar to the commercial alloys. An alloy coating on a low-alloy steel or carbon steel substrate would require significantly less strategic and critical metals than those contained in an equivalent mass of the commercial alloy. Coatings applied to appropriate mandrel materials make possible the preparation of intricately-shaped alloy electroforms (near-net-shape parts). As a result, the loss of valuable metals associated with machining finished products would be minimized.

Jan 1, 1986

By A. R. Taylor

Low-temperature heat capacities of cesium chloride (7° - 300° K) and cesium iodide (13° - 300°K) were measured with an adiabatic calorimeter. The heat-capacity measurements were analyzed graphically to determine smooth values of heat capacity, entropy, enthalpy function, and free-energy function at 10° K intervals and at 273.15° and 298.15° K.

Jan 1, 1963

By John J. Mulligan

The Bureau of Mines sampled a gold-bearing schist series 50 miles east of Nome near Bluff, a dormant mining camp on the southern shore of the Seward Peninsula, Alaska. Gold is unevenly distributed through a section of a schist series that extends from the coast northward 4,500 feet. In this section the schists dip westward 20 to 38 degrees and have an outcrop width of about 1,000 feet and a normal width of about 500 feet. An intensely fractured zone within the schists averages 0.015 to 0.017 ounce of gold and 0.03 to 0.05 ounce of silver per ton for outcrop widths of 200 to almost 500 feet. The grade of the remainder of the schist series ranges downward to scant traces. Gold eroded from these schists collected in solution channels in metalimestones to form the Daniels Creek placers, which also extend from the beach southward under the sea for an unknown distance. The lode sources of the gold placers elsewhere in the southern Seward Peninsula may be similar schists that occupy a similar position in the metasedimentary series.

Jan 1, 1971

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

This report was prepared by The Pennsylvania State University under USBM Contract No. H0133040. The contract was initiated under the technical direction of PMSRC, with Mr. Edward D. Thimons acting as the technical project officer. Mr. Frank Naughton was the contract administrator for the Bureau of Mines. This report is a summary of the work recently completed as part of this contract during the period June 30, 1973,to June 30, 1977. This report was submitted by the authors on August 31, 1977.

Jan 1, 1977

By S. J. Anderson

The Bureau of Mines compared three methods of rock cutting using drag cutters under controlled laboratory conditions. The methods tested were the conventional drag cutting method used on continuous miners, the kerf-core method used on some boring machines, and an experimental method called ripper cutting. All three methods were tested in blocks of Indiana and Kasota limestone. The results of this testing showed ripper cutting to be 30 to 40 pct more energy efficient than both the conventional and the kerf-core methods in Kasota limestone and 35 pct more efficient than the kerf-core method in Indiana limestone. The conventional method was, however, 9 pct more energy efficient than the ripper method in Indiana limestone. These results are considered promising, and more tests are planned with the ripper cutting system.

Jan 1, 1987

By M. A. Trevits, S. W. Lambert

In this Bureau of Mines investigation, production was monitored for 1 year at over 30 coalbed gas-drainage boreholes located in Alabama, Pennsylvania, and West Virginia. Results indicate that the quality of data gathered from such wells can be improved greatly if potential problems are anticipated and prevented in the early stages of well production. Major water-monitoring problems include solids buildup, freezing, the presence of gas in surface waterlines, and improper pumping interval settings. Such problems may be avoided by incorporating in the original well design waterline filters, sand screens, separator tanks, and systems to automatically control pumping intervals. Problems related to measurement of coalbed gas flow include large quantities of water vapor contained in the gas, especially during winter months; freezing and subsequent obstruction of flow; sudden, uncontrolled release of gas pressure; and solids buildup in metering equipment. The installation of commercially available items, such as filters, separators, and insulation, and the thoughtful application of a basic knowledge of coalbed gas reservoir characteristics will prevent most production-monitoring problems.

Jan 1, 1978