Search Documents

By Donald R. Johnson

Apparatus providing simultaneous differential thermal analysis, thermo-gravimetry, and evolved gas analysis, has been developed by the Bureau of Mines specifically for thermal study of oil shale and other solid, natural fuels. The apparatus is described in detail, and simultaneous analyses on a single sample of an oil shale mineral, nahcolite, and a thermal analysis demonstration compound, calcium oxalate monohydrate, are presented to demonstrate the instrument's capabilities.

Jan 1, 1970

To reduce the exposure of mining machine operators to respirable dust. Approach: A protective curtain of filtered air is blown down around the operator's head, from a manifold mounted on the machine canopy. How It Works: Mine air is drawn into the system through a filter which removes respirable dust. The filtered air enters a centrifugal blower which pushes it through a flexible hose to a manifold mounted on the canopy above the operator. Air leaves the manifold through a perforated plate and flows down around the operator's head. A photograph of an installed system can be seen in Figure 1. The second photograph, Figure 2, shows the sys-tem components. An important advantage of this dust protection system is that it is not worn or carried, or in any way connected to the operator. It is therefore not uncomfortable, encumbering, or

Jan 1, 1976

By D. W. Frommer

Processing of nonmagnetic taconites by selective flocculation-des liming and anionic flotation of calcium-activated silica has been investigated using innovative procedures as a means of improving operating costs. Areas chosen for cost-cutting evaluation were grinding, fine screening, and water conservation and reclamation. The investigation was performed on Marquette range nonmagnetic taconites in the Bureau of Mines Twin Cities Metallurgy Research Center flotation pilot plant, at feed rates ranging between 900 and 1,100 lb/hr. With fully integrated water reclamation, flotation concentrates containing 65.8 percent Fe and 3.4 percent Si02 were made in the best operating period, with accompanying weight and iron recoveries of 40 and 74 percent, respectively. During this same period, the estimated cost of both flotation and water reclamation reagents was only $0.80 per ton of concentrate (1968 pricing basis). This cost is about 15 percent lower than obtained previously at this Center for flotation reagents only. The investigation demonstrated additional potential savings in operating costs of approximately $0.96 per ton of concentrate through autogenous grinding as a substitute for ballmilling. Fine screening of intermediate concentrates was employed advantageously, but the frequency of blinding may be a factor militating against use of the screen in this flotation system.

Jan 1, 1973

Reduce the danger to personnel and destruction of equipment caused by fires on surface coal augers. Approach: A reasonably priced reliable system which automatically senses a fire and activates dry chemical extinguishers, has been built and field tested. How It Works: Heat sensors mounted in the engine compartment and hydraulic hose areas detect the fire, usually before the operator does. This causes the system to automatically discharge A-B-C class dry chemical extinguisher through a fixed piping system.

Jan 1, 1976

By P. B. Altringer

The Federal Bureau of Mines conducted a study to determine if residues from fractional distillation represent a potential source of mineral values. A literature review and discussions with tar sand specialists failed to disclose the mineralogical nature of residues remaining after bitumen extraction. To develop this information, pilot plant tar sand residues or toluene-cleaned tar sands from 23 deposits were examined. The nature of the residues was determined by standard mineralogical methods and the chemical compositions were determined by X-ray and ICP (inductively-coupled plasma spectroscopy). None of the sands or concentrates examined contained sufficient valuable minerals to be economically important.

Jan 1, 1982

By E. P. Carman

This report is the 19th in a series summarizing Bureau of Mines research and technologic work on coal and related investigations. The first 17 reports covered fiscal years; however, the 18th report3/ covered the 18 months from July 1, 1952, to December 31, 1953, to permit the publication of this and subsequent reports on a calendar-year basis. Most of the material in this report relates to publications by Bureau authors issued during the reporting period. Some work is referred to on which the results have not yet been published or may not be published for security or other reasons. In a few instances publications are mentioned that were issued before the reporting period but were not included in previous reports. Further details on the published work described herein may be found in the publications cited in the footnotes. Research and technologic work on coal by the Bureau is directed toward developing and encouraging increased conservation of coal resources through safer and more efficient mining, preparation, and utilization. Significant advances were made during the year in these fields, particularly in coal-mine safety and in preparation and utilization of the various ranks of coals.

Jan 1, 1956

By Alla D. Mah

The heat of formation of scandium sesquioxide (Sc203) has not been measured previously, and existing values for gallium sesquioxide (Ga203) are subject to large uncertainties. As a consequence, thermodynamic calculations involving these oxides hare lacked scientific exactness. This paper reports newly determined values of the heats of formation of gallium and scandium sesquioxides at 298.15° K., by combustion calorimetry. The corresponding free energies of formation are derived from heat and entropy data.

Jan 1, 1962

By Abdurrahman Cetinbas

The effect of water infusion on the flow of methane and on the production of dust was investigated at an active face in the Pittsburgh coalbed. The average total flow of methane at the face decreased by approximately 79 percent, whereas the flow from the ribs increased about 24 percent after infusion. On the day after infusion, dust concentrations appear to have been reduced; however, the presence of large quantities of rock dust obscured the results on the following days.

Jan 1, 1972

By C. M. Mason

Mechanical mining produces large quantities of very fine coal dust called float dust. The associated increase in hazard requires a reexamination of the Bureau of Mines method of evaluating the incendivity of explosives in coal dust-gas-air mixtures. A technique recently developed by Bureau of Mines laboratories for evaluating the incendivity of explosives in coal dust-air mixtures was applied, with modifications, to coal dust-air-natural gas mixtures. A series of permissible explosives were evaluated by this modified technique. Results indicate that the modified technique could be the basis of a more discriminatory procedure than that presently in use.

Jan 1, 1968

By Edward L. McHugh, Stanley M. Miller, Jeffrey K. Whyatt

The point estimation method can be applied to the safety factor (SF) equation for any specified rock slope failure mode (such as plane shear, step path, or wedge) to obtain reliable estimates of the mean and standard deviation of the SF probability distribution. A gamma probability density function is recommended for modeling this probability distribution, because it allows only for positive values and is flexible enough to provide symmetrical shapes and right-skewed, exponential-type shapes for the SF distribution. The mean and standard deviation define this distribution, which then can be integrated numerically from 0 to 1 to obtain the probability of sliding, PS (portion of the SF distribution where SF < 1.0). The overall probability of failure, PF, for the potential slope failure mass is the joint probability that the rock discontinuities are long enough to allow kinematic failure (PL) and that sliding occurs along the rock discontinuities (PS); that is, PF = PSPL. This method for estimating the probability of sliding is extremely efficient computationally, and thus, expedites slope stability simulation routines used by NIOSH software to stochastically describe rock slope behavior and assist the engineer in designing catch benches for large rock slopes. Enhanced bench design translates into increased operational efficiency and safer working conditions in open pit mines and quarries.

By Motohisa Kanda

The time and amplitude statistics necessary to adequately describe electromagnetic (EM) noise in mines are illustrated through computer software techniques. They are 1) Allan Variance Analyses (AVA), 2) Interpulse Spacing Distributions (ISD), 3) Pulse Duration Distributions (PDD), 4) Average Crossing Rates (ACR) , and 5) Amplitude Probability Distributions (APD) . These statistics are illustrated using data taken from a rather large store of raw analog data recorded in operational mines. The curves generated for the illustrations characterize the noise environment in the mines from which the corresponding data were taken, and should aid in the design of reliable communication systems for such mines.

By J. E. Urosek, K. L. Cashdollar, D. A. Beiter, G. J. Shemon

The National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research to evaluate explosion blast effects on mine ventilation stoppings at the NIOSH Lake Lynn Experimental Mine (LLEM). After mine explosion accidents, MSHA conducts investigations to determine the cause(s) as a means to mitigate or eliminate future occurrences. As part of these post-explosion investigations, the condition of underground stoppings, including the debris from damaged stoppings, are documented as evidence of the strength and the direction of the explosion forces. The LLEM data showed that a total pressure of 52 kPa (7.6 psi) destroyed the solid concrete block stopping, ~36 kPa (~5.2 psi) destroyed the hollow-core concrete block stopping, and 9 kPa (1.3 psi) destroyed the steel panel stopping. These results will assist investigators in determining the explosion forces that destroy or damage stoppings during actual coal mine explosions.

By Arnold O. Tanner

The recession that took hold of the domes-tic mining industry in 1981-82 finally abated somewhat in 1987, resulting from increases in many commodity prices, especially in the metals sector, and from continuing success in lowering operating costs. By no means was the work finished; the mining industry was in a sense entering a new era. The struggle for survival was still very evident for many companies and various commodities, but increasing productivity and profits were accompanied by indications that these trends were more long term than short term. Raw nonfuel minerals produced in the United States during 1987 had an estimated value of $26.3 billion, an increase of $2.9 billion over the 1986 value. This is the fifth consecutive year that the value has increased. Except for a decrease in 1982, the value each year has increased since 1971, or 15 of 16 years. The value of raw metals production increased by an estimated 28%, an impressive improvement since the drastic fall in 1982. Industrial minerals growth was comparatively flat, with an estimated in-crease in value of 0.1 %, continuing a trend of the previous 2 years. Metal mine production dropped considerably in 1982 and maintained its resultant lower level until 1987, when production significantly recovered.

Jan 1, 1989

By J. T. May

The Federal Bureau of Mines investigated the extraction of lithium from hectorite-type clay deposits found on the Nevada-Oregon border. Two clay samples were used in the investigation; one contained 0.36 pct Li and the second contained 0.64 pct Li. The purpose of this laboratory-scale research was to determine how these clays responded to different extraction techniques. Extraction techniques investigated were sulfuric acid leach, sulfuric acid bake-water leach, and roast-water leach procedures with cholorides, sulfates, carbonates, and combinations of these reagents. The processing characteristics of the clay samples showed significant variations, and no one technique was effective for both materials. Lithium extractions near 90 pct were achieved during these exploratory studies.

Jan 1, 1980

By S. R. Zimmerley, John Gross

"The investigation discussed in this paper was undertaken to obtain fundamental data on crushing and grinding and has been confined, so far, to work on quartz.The results of crushing or grinding have hitherto been judged entirely by the amount of the various-sized particles produced, based. on sieve sizing for particles above 74 microns in size and on microscopic measurement or elutriation for particles below 74 microns - a method which could give only a general idea of what had been accomplished.There was a distinct need of a ""yardstick"" for the measurement of crushed material. It appeared that no advance in the fundamental investigation of crushing and grinding could be made without a reliable method of surface measurement and that such a measurement would have to be based on some property of the surface of the crushed material.A number of attempts based on various surface actions, such as adsorption and heat of wetting, were made to measure surface on quartz particles, but all gave unsatisfactory results. After some preliminary work it was decided that a dissolution method based on Wenzel's law-- ""the reaction velocity between solids and liquids is proportional to the area. of contact""4 -- would be the most feasible.Early use of the dissolution method had been made for surface measurements5, and lately Dr. Geoffrey Martin and his coworkers in England used the dissolution method to determine surface on quartz. They compared the amount of quartz dissolved from a sample in one hour by a hydrofluoric acid solution, with the amountdissolved from a measured quartz cuboid6,After investigating the solvent power of sodium carbonate, sodium hydroxide, and hydrofluoric acid for quartz, hydrofluoric acid was selected as the most suitable solvent, and a dissolution method was developed which gives very reliable results.During the dissolution of quartz in hydrofluoric acid, the reaction velocity changes for two reasons: there is a change in concentration of solution, and a change of surface of the solid. The amount of quartz dissolved in a definite period of time is therefore not a true measure of surface. If, however, the reaction velocity or rate of dissolution for various periods of time be plotted, a curve will be obtained which, if extrapolated to the zero time ordinate, will give the rate of dissolution before any change of surface or any change in the solvent has taken place, and which is a true index of surface. This rate of dissolution, expressed in percentage of the original sample at the zero time ordinate, is designated herein as the ""Initial Rate"" or as simply ""I. R."""

Jul 1, 1928

New Continuous Personal Dust Monitors (CPDM) submitted to NIOSH for approval to sample coal mine dust must accurately measure respirable coal mine dust in mine environments. There are two steps in the process which may be done in any order. The manufacturer is required to submit the results of a comparative underground coal mine dust sampling study, where the candidate CPDM is compared to an approved coal mine dust sampling device (currently the Coal Mine Dust Personal Sampling Unit (CMDPSU)). This testing shall follow the guidelines outlined below and shall demonstrate through weighted regression analysis that the mean coefficient of variation with bias correction is equal to or less than 12.8%. The other step involves laboratory testing to determine the electronic and environmental stability. This testing must be conducted by a private, commercial, academic or other laboratory approved by NIOSH.

Jan 1, 2009

By Robert C. Hickman

"INTRODUCTION Two holes were drilled on the G. S. Stiner zinc prospect, in the Lead Mine Bend area of Union County, Tenn. The holes were drilled in the vicinity of an area of gossan float and were bottomed in the Maynardville formation of the Nolichucky shale. Drilling was started January 24 and completed February 16, 1947. The total footage drilled was 421.2 feet.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, does the actual investigative Work, and prepares the final report. The Metallurgical Branch, Cliver C. Ralston, chief, analyzes samples and makes beneficiation tests.The project was under the general supervision of Mitchell H. Kline, chief, Raleigh Division, Mining Branch, Raleigh, N. C.LOCATION AND ACCESSIBILITYThe prospect is located approximately 20.5 miles southwest of Tazewell, Tenn. It is reached from Tazewell by driving 13.8 miles southwest on State route 33, thence 6.8 miles over graveled roads in a northwesterly direction to Stiner's general store. The drill holes are located in the bottom land northeast of the store (fig. 1 and 2)."

Feb 1, 1948

By Michael Sokaski

The Cliff Springs prospect in the northern part of the Slate Range Wilderness Study Area (WSA) contains only minor amounts of gold and silver. Clay near this prospect contains insufficient aluminum to be of economic interest, although alunite claims are recorded in the vicinity. Mineralized rock at the Crescent Mine adjacent to the WSA contains gold, silver and lead occurrences. The host rock may be present in the extreme southwestern part of the WSA, which is covered by alluvium. Substantial sand and gravel deposits are present but these occurrences are remote from markets. Much of the USA is underlain by volcanic rocks and alluvium and consequently the mineral resource potential there remains unknown.

Jan 1, 1983

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

1 11 THIS IS A DIGITAL COMPUTER SIMULATION OF THE VENTILATION SYSTEM OF A MINE LOCATED IN WASHINGTON COUNTY, PENNSYLVANIA. THE VENTILATION SURVEY ON WHICH THIS SIMULATION IS BASED WAS RUN FROM OCT. 27-30 AND ON NOV. 2, 1976 IN THE ACTIVE PORTION OF THE MINE INBY COMBS SHAFT AND THE INACTIVE PORTION AFCUND AND INBY DONAHOO SHAFT. FOLLOW-UP SURVEYS WERE THEN RUN ON FEB. 18 AND FROM MARCH 7-11, 1977 TO INCLUDE THE MAIN HAULAGE SYSTEM OUTBY THE ACTIVE AREAS OF THE MINE. ALL SURVEY DATA WAS NORMALIZED TO A STANDARD DENSITY OF 0.075 POUNDS/CU.FT. PRIOR TO THE CALCULATION OF INPUT PARAMETERS FOR THIS SIMULATION. IN THIS RUN, THE ORIGINAL VENTILATION NETWORK HAS BEEN MODIFIED TO INCLUDE NEW INTAKE AND RETURN AIRSHAFTS AT THE WEST MAINS.

Jan 1, 1977

By Kenneth J. Miner

Pittsburgh bed and Lower Freeport bed coals were tested in the U.S. Bureau of Mines two-stage froth flotation pilot plant, which utilizes a new flotation process to remove pyritic sulfur. The process consists of a first-stage coal flotation step to remove coarse, free pyrite and other refuse in the tailings. The clean coal froth concentrate is then repulped and treated with a coal depressant, a pyrite collector, and a frother to selectively float the remaining pyrite in a second stage. Results in the pilot plant were excellent, comparing well with those obtained in laboratory batch tests. That is, about 70 percent of the pyrite present in the Pittsburgh bed coal and about 90 percent of the pyrite present in the Lower Freeport bed coal were removed with excellent final clean coal recoveries.

Jan 1, 1973