Search Documents

By Michael J. Brnich

Since 1991, Pittsburgh Research Center (PRC- formerly part of the Bureau of Mines) researchers have recorded extensive interviews with 30 individuals who are experts in the area of mine emergency response. These individuals, who have an average of 35 years of mining experience and 29 years of mine emergency response experience, related stories and observations from events that they experienced during their combined 850 plus years in mine emergency response. The purpose of this effort was to gather information that could be passed onto both today?s and tomorrow?s mine emergency responders to train and guide them in handling future events.

Jan 1, 1997

By Kelly C. Strebig

Laboratory tests were conducted by the Bureau of Mines to determine the effect of depth of cut and bit type on respirable coal dust generation. Apparatuses were constructed to contain the coal samples, measure the linear cutting forces, and analyze the dust generated. Single-bit tests were conducted in Illinois No. 5 and Pittsburgh seam coals with five bit types at four depths of cut. The results showed that bit type did not significantly influence dust production. On the other hand, deep-cutting bits were more efficient and generated substantially less respirable dust per pound of coal broke than shallow-cutting bits.

Jan 1, 1975

By J. W. Walkiewicz

One of the objectives of the Bureau of Mines is to develop substitution technology for scarce materials. In accordance with this goal, alloys containing lanthanum, cobalt, copper, and magnesium were investigated for fabrication of rare-earth-cobalt (RE-Co) permanent magnets. A complete substitution of lanthanum for samarium and a partial substitution of copper for cobalt was accomplished. Magnets of La-Co and La-Co-Cu-Mg alloys were fabricated by powder metallurgy techniques and evaluated. A maximum intrinsic coercivity of 23.2 kOe was obtained with a La-Co-Cu-Mg alloy. In comparison, maximum values of 9.3 kOe and 11.6 kOe were obtained with La-Co and La-Co-Cu alloys, respectively. The substitution of copper and magnesium for part of the cobalt resulted in a large increase of intrinsic coercivity, similar to the results of Bureau research with mischmetal-Co-Cu-Mg alloys. Unlike the mischmetal-Co-Cu-Mg magnets, the La-Co-Cu-Mg magnets showed signs of physical deterioration on exposure to air. The effects of fabrication parameters on the magnetic properties of the La-Co-Cu-Mg alloys were also determined.

Jan 1, 1982

By Ralph L. Brown

"IntroductionThe accumulation of gummy and resinous deposits in consumers' gas meters began to assume serious proportions about 1917. As the trouble developed and spread in the years following, it manifested itself in several ways, which ultimately began to the expressible in distinctly economic terms, more specifically in terms of costs; in 1922 an organized and fundamentally based investigation of this trouble was begun. In an earlier paper*** a short statement of the occurrence and costs of the deposition was given and at the same time an analysis of the problem, as well as well as a general plan of attack, was presented. That plan included two general phases, first, a chemical study of typical was 1 quarry or 2 cosinous content , mauformly consituents, rmln and selected subjects; and secondly, a comparative survey of plants affected and sufficient therewith, attention being paid to construction, operation, meter conditions and related data. In reporting progress in the axtual investigation, it was definitely set down that the basis of the gummy deposits was the unsaturated hydro consulting from the carburxtion of the water-gas with oil. That the presence of oily-gas condensate was closely associated with and largely"

Jul 1, 1923

By S. H. Ash

"INTRODUCTION Mine fires have occurred since underground mining of minerals began, and they are still occurring. The technical literature is replete with papers relating to mine fires.Means and methods for controlling and extinguishing mine fires and preventing explosions and other accidents require the collection and analyses of samples of the atmospheres surrounding the fire. Such atmos¬pheres are complex mixtures of gases (1, 3, 4, 15, 21, 23).3/SUMMARYExperiences at mine fires (1, 3, 4, 15, 21, 23) have proved conclusively that mine-air analyses furnish the only means of judging what is going on in a mine fire area. Mine-air analyses give evidence of conditions that require immediate protection, govern the order and control the manner in which a fire is fought, show the necessity of bulkheads and establish the places to construct them, indicate whether or not a fire is being controlled or is being extinguished, and govern procedure in sealing and unsealing mine fires.It is commonly believed that danger to life and property from mine-fire atmospheres is greatest in coal mines; this is true only to the degree that the explosion hazard is greater in coal mines than in noncoal mines because of the presence of combustible gases. The problem of gas poisoning is greater in noncoal mines because of the more frequent occurrence of poisonous and innocuous gases, oftentimes the lack of controlled ventilation, and usually greater difficulties in sealing mine-fire areas. Sulfide minerals present a serious hazard in many metal-mine fires when sulfur dioxide is formed. The country rock or ore body itself may contain or be limestone, which may be calcined. Emanations of carbon dioxide are found."

Dec 1, 1950

Underground and strip mining (6,7) produce different hydrologic environments. Many underground mines are below the zone that is completely saturated with water and the mine openings may cause new and continuous contact between sulfurous material and water which flows from the saturated zone to the workings. Strip mines are usually above the zone of continuous saturation and contact between sulfurous material and water is generally restricted to periods of precipitation. A full appreciation of the problem of water pollution caused by drainage from deep mines requires a basic understanding of occurrences and movement of water in the ground and the modes of ground water entrance into mining areas.

Jan 1, 1970

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

C 2 Complete Hoisting Systems A Above Ground Installations A total of seven companies were identified who supply complete emergency escape hoist units for above ground installations The units have been designed predominately to meet the needs of coal mine operators to satisfy the requirements of the Coal Mine Health and Safety Act of 1969. The seven companies are as follows 1 Dover Conveyor and Equipment Co. 2. Coeur d' Alenes Co. 3. Connellsville Corp. 4. Scott Midland 5. W W Williams Co. 6. Equipment Corporation of America 7. Timberland Ellicott Table VIII contains detailed specifications and price information on each of these units. The units have a number of similarities

Jan 1, 1976

By David J. MacDonald

Stability constants, that is, equilibrium constants for complex-formation reactions, have been determined by a titrimetric method for complexes formed by the transition metal ions Ni2+, Cu2+, Zn2+, and Cd2+ with the structurally analogous bidentate ligands N-ethylethylenediamine and 2-(ethylthio)-ethylamine. The sulfur containing ligand was found to be the weaker of the two chelating agents for each of the four metals. Absorption spectra of the individual complexes have been determined in order to calculate their crystal field stabilization energies. The combined results suggest a linear relation between free energy of chelation and ionic radius of the metal ion.

Jan 1, 1972

To increase awareness of float coal dust explosion hazards in the mining industry.

Jan 4, 2006

By G. R. Friggens

A nuclear method for continuously monitoring the coalbed and ash levels and void formation in commercial-scale, fixed-bed, pressurized gas producers is proposed. Measurement of gamma ray transmission through the coalbed is the basis of the method. The coalbed level is monitored by detecting the trans-mission of gamma rays from a 1 to 2 Ci Co-60 source positioned on the outside wall of the vessel. Coal bridging or, alternatively, ash level is monitored by a 10 Ci Co-60 source at the center of the coalbed. Source activities and geometries are calculated for a 12-foot-ID producer designed to operate at 350 psi. Source capsule and detector specifications and operational safety are also discussed.

Jan 1, 1973

By Marie Farnsworth

"The Anhydrite ProblemThe Nonmetallic Minerals Experiment station of the Bureau of Mines at Rutgers University, New Brunswick, N. J. has recently undertaken a study of the chemical and physical properties of anhydrite having in view its wider utilization anhydrite (CaSO4) in contact with water at ordinary temperature and pressure rehydrates, slowly forming gypsum (CaSO4.2H42O). In nature this is an extremely slow process, and laboratory experiments are being conducted to determine methods of accelerating the rehydration. The tests recorded herein cover one this study, and while they are negative in character in so far as the major problem is concerned, certain facts established by the tests, bearing on the stability relations of gypsum and anhydrite seem sufficiently important to be placed on record.Early Researches on Gypsum and Anhydrite.It is to Lavoisiar that we are the first scientific study of the calculation and hardening of plaster of Paris. He sums up his experiments in the following passage: ""If gypsum, which has been deprived of its water of by means of heat, is again treated with water (to make what is commonly called mortar) it takes it up with avidity, rapid and irregular crystallization occurs, and the small crystals which are formed are so entangled in each other that a very hard mass results."" Later, he observed that the dehydration of gypsum occurs in two stages: three-fourths of the combined water is much more easily driven out than the last fourth. LeChatalier first determined the temperature decomposition accurately, his method was as follows: Pulverized gypsum was placed in a glass tube in the middle of a paraffin bath, the temperature of which was raised in a progressive and regular manner. A thermometer gave at each instant the temperature the salt, and the passage of the mercury column past each division of —co. was cared by a registering chronograph. The rise in temperature was except at 128°C. and 168°C. where breaks occurred."

Nov 1, 1924

To evaluate the effectiveness of dust collector bags for reducing dust liberation from a roof bolter dust collection system.

Jan 2, 2007

By W. E. Wallace, P. Bolsaltis, M. J. Keane, B. L. Rauaboni

Thermal treatment of respirable size silica dust samples results in marked changes in their hemolytic activity. These changes can be correlated with changes in the characteristics of the particle surface as measured by infrared spectra, zeta potentials, and specific surface area. Silica samples from various sources (Min-U-Sil, fumed silica, and a NIOSH standard sample) were heated or calcined at temperatures ranging from 100-1095C. The hemolytic activity of the crystalline materials decreased after thermal treatment. The behavior of the fumed material was found to be more complex. Material of very large surface area (small particle size) exhibits an initial increase in hemolytic activity upon calcination. This result confirms other experimental observations pointing to a particle size of maximum toxicity. Tre changes in hemolytic activity can be related to infrared spectra and zeta potentials of the materials. The absorption band in the 3200-4000 cm-1 frequency region of the fumed material disappears upon heat treatment while a sharp, characteristic band at 3750 cm-1 increases in intensity. Zeta potential measurements conducted in the pH range of 2.0-10.5 exhibit a unique change in zeta potential v.s. pH profile with heat treatment. These findings indicate that the removal of active surface silanol groups by calcination results in reduced cytotoxicity, as measured by a hemolysis test.

Jan 1, 1988

By Charles L. Kimbell

The final 26 tables of this chapter, tables 14-39, extend and expand the statistical series on production that was started in the 1963 edition of the "Area Reports: International" volume of the "Minerals Yearbook" and that was subsequently updated and expanded in the 1965 and 1967-88 editions. In this year's edition, for the first time, a column has been added to each of these tables providing a 5 year average for 1985-89, inclusive. This should provide a clearer picture more rapidly of the role of each major producer over the 5-year period. The listing order of major producers, however, continues to be, as in past years, in descending order of rank in the year of review, 1989. With the inclusion of silver and uranium oxide in the 1988 edition of this chapter, this group of tables now includes each of the crude minerals that ranked from 1st to 19th in 1983 in terms of value of their output (as well as four others of lesser rank). These 23 crude mineral commodities accounted for 93% of the estimated value of world crude mineral of world crude mineral production in 1983. In addition, world output of five key down-stream products-aluminum, steel, cement, nitrogen in ammonia, and refined oil are included because of their significance as products.

Jan 1, 1992

By Charles Findlay, Stephen Krickovic

A methane emission rate study was conducted in 1969 on a longwall section of a Lower Kittanning coalbed mine in central Pennsylvania. The longwall face was mined with a drum shearer between developed headings on the head end and headings on the tail end that were driven with a ripper-type continuous miner as needed. The study was conducted over 22 consecutive shifts (7-1/3 days). The average methane emission rate from the Lower Kittanning coalbed during mining at the face and developing the headings at the tail end of the face was 34 cfm. Caving of the gassy overlying strata as the result of mining at the face increased the methane emission to rates ranging from 702 to 1,049 cfm.

Jan 1, 1971

By L. B. Pankratz

Enthalpies above 298° K were investigated for four crystalline sodium borates by copper-block drop calorimetry. Determinations were made to 1,200° K for NaB02, 1,003° K for Na2B407, 1,005° K for NaB305, and 1,046° K for Na2Be013. No phase transitions or other thermal anomalies were found. The enthalpy determinations, when combined with known heats of formation at 298° K and other supplementary data, enabled the calculation of the heats and free energies of formation of the compounds to their melting points. Values of relative enthalpies, entropies, heat capacities, free energy functions, enthalpies of formation, free energies of formation, and equilibrium constants of formation were tabulated at even temperatures.

Jan 1, 1971

Reduce the airborne dust generated in a longwall coal face. Approach Reduce the rotational speed and increase the depth-of-cut of the longwall shearer. How It Works An Anderson-Mavor AM500 double-ended ranging drum shearer was fitted with drums specially designed to accept the large picks required for this testing program. Change gears In the shearer allowed rotational speeds of the drums to be set at 35, 45, 55, or 70 rpm. As deep cutting removes larger coal fragments, the specific energy requirements of the operation are reduced and less surface area results. Dust generation and shearer power consumption are also reduced. The lower rotational speed minimizes the fanning action of the cutterheads and thus reduces the amount of coal fines that become airborne.

Jan 1, 1981

By Fred N. Kissell, Maurice Deul, T. D. Moore

Methane emission from two surface gob-degasification boreholes was measured by the Bureau of Mines. The investigation took place during mining of a 3,200-foot longwall panel in the Lower Kittanning coalbed in central Pennsylvania. The first hole was 500 feet from the start of mining, and the second hole was 2,200 feet. The first hole went on natural draft as soon as the longwall face passed it. This caused the methane flow in the return entries to drop 75 pct. In the 6 months required to complete the panel, the two holes emitted 69 MMcf of methane in varying percentages of concentration in air. In 3 years, the holes emitted a total of 150 MMcf of methane.

Jan 1, 1976

By J. Hudy

The performance of six dense-medium washers was evaluated in five preparation plants. Three of the plants were making a two-product separation that produced a clean coal and a refuse; one plant employed dense-medium vessels in series to effect a primary and a secondary separation; and one plant was equipped with a two-compartment washer effecting two separations in one vessel. The separate secondary drum-type washer produced a low-ash metallurgical coal and an intermediate-ash product suitable for plant fuel or steam generation. The two-compartment washer produced a premium anthracite product and a middlings product. The sharpness-of-separation values ranged from good to excellent for the five primary separations and for the secondary separation.

Jan 1, 1968

By Nicholas T. Zilka

One mineral deposit in the Golden Trout Wilderness has potential. The currently producing Pine Tree Mine on the Little Kern River has an estimated 120,000 tons (109,000 t) each of indicated and inferred reserves averaging 0.77 percent tungsten trioxide. No apparent potential exists for base or precious metal or other mineral deposits. INTRODUCTION The Golden Trout Wilderness, established by Congress in 1978 under Public Law 95-237, encompasses 240,000 acres (97,000 ha) of conifer-forested, rolling, upland plateau at the headwaters of the Kern River in Inyo and Sequoia National Forests (fig. 1). Abundant streams locally contain Golden Trout, namesake of the area. Major roads serve the area to the west and east of the Wilderness; access is poor to the north and south.

Jan 1, 1982