Search Documents

By Glenn A. Hazen

This report presents a stress investigation of four coal pillars located under two depths of cover. Each coal pillar was instrumented with ten load cells designed to measure coal pressure during initial and secondary mining. The problem considered was one of uniform triaxial stress as a large coal pillar was loaded under a thick limestone bed. Special attention was given to pillar design procedure. Unconfined uniaxial compression tests were conducted for coal specimens 7/8 in., 2-1/8 in., 3 in., and 4 in. square with length to square side ratios of 1/2, 1, 1-1/2, and 2. Stress-strain curves were recorded. Six specimens were tested at each size. Results show that a coal pillar is composed of an inner zone which is highly loaded plus a region around its perimeter which has lost its elastic strength. The bearing capacity of a coal pillar consists of elastic and crushed coal response: The failure strengths have been determined and will be useful in coal recovery, mine design, and mine safety.

Jan 1, 1975

By E. H. Denny

The presence in the Cripple Creek district, Colo., of irrespirable gas or gases, generally known to consist mainly of nitrogen and carbon dioxide, has been recognized by members of the mining industry in that region almost since underground mining was begun there; the occurrence, origin, and possible control of these gases have been discussed in several articles cited at various places in this report. Similar gases have also been studied in other metal-mining districts, as later discussed. In March, 1925, there were two fatalities from rock-strata gases in the shaft of the Index mine, near Cripple Creek. Two men repairing the bell or signal line preparatory to reopening the shaft were lowered into irrespirable gases and died. Their bodies were recovered by rescue crews from the United States Bureau of Mines and .the Portland mine, Victor, Colo. These crews found it necessary to use oxygen breathing apparatus. In October of the same year a miner was trapped on the 6 level of the Midget mine by an influx of gases that filled the shaft to a point above that where he was working. Oxygen breathing apparatus was again used by Bureau of Mines employees, who were in the vicinity, and the man was brought out in time to save his life. These two fatalities and one near fatality seemed to show that additional investigation of the gases and methods of control might be warranted. Accordingly, field and laboratory studies were begun by the authors of this report after a visit to the district by M. van Siclen, then engineer in charge, mining research division, Bureau of Mines, and after conferences with the Mine Owners' Association of Cripple Creek and with J. T. Joyce, metal-mine commissioner of the State of Colorado. The mine operators of the Cripple Creek district and the State mine commissioner's office gave whole-hearted cooperation in this work.

Jan 1, 1930

By J. D. Clendenin

Systematic practices for protecting crops from frost damage began in the United Metes more then 40 years ago when the Weather Bureau Fruit-Frost Warning Service was organized; however, various practices employed in frost protection are centuries old. Although there are areas where little doubt exists as to whether protection is needed, there are also circumstances where there is some doubt as to the need for frost protection. Many factors influence this, including not only critical temperatures but also the maturity dates of the crops relative to marketing. Critical temperatures for frost damage to trees, plants, blossoms, and fruits very with weather, plant variety and nutrition, and stage of growth. In the case of truck crops, a single night of protection from frost injury might yield big dividends with a variety of sweet corn or tomato that matures early while price is high yet be worth very little with a midseason or late-maturing variety. Consequently, it is the individual grower who must decide whether to use frost-protective measures on the basis of his returns, the quantity and quality of his crop, the marketing situation, the sensitivity of his crops to frost damage, and the frequency of damaging frost in his area.

Jan 1, 1955

By S. M. Molloy

The postwar demand for insulating material such as mineral wool, in-creased in proportion to the rapid construction of new buildings, placing an enormous burden on the existing mineral-wool industry both in known sources of raw materials and in available plant facilities. In view of the increased demand on the industry, the Bureau of Mines in its Mississippi Valley Experiment Station" Rolla, Mo., undertook an investigation to aid the industry by establishing resources of raw materials through actual laboratory wool-blowing tests and by developing certain methods for evaluating the physical proper-ties of a mineral wool. As material was received from the public, laboratory-evaluation technique had to be developed, the results of which would reflect in the mineral-wool-industry standards. The methods of testing used by the mineral-wool industry, not only would have required a pilot-plant installation capable of producing a large tonnage of mineral wool, but each wool-blowing campaign would have been very expensive and necessitated considerable personnel and equipment. The present laboratory wool-blowing equipment can produce as high as eight wool-blowing campaigns a day. The nature, simplicity, and size of the physical testing equipment permit testing as small a sample of wool as 25 grams and give information as reasonably accurate as in a 40-pound bag of wool. The purpose of this report is to describe the laboratory method of production and the evaluation of the physical properties of small quantities of mineral wool. Considerable work has already been done, and the interest of the public and industry is measured in the number of samples being submitted for testing.

Jan 1, 1948

By D. Harrington

This circular presents part I of a review of the literature on effects of breathing dusts, with special reference to silicosis, largely in the minim; and allied industries. The literature on this subject is so extensive that no attempt has been made to include all published material but only to assemble some of the more outstanding data on several aspects of the subject. Parts II and III will deal with prevention and treatment of dust diseases and some of the economic and legal aspects of dust diseases in industry, with special reference to mining. Dust diseases arc much before the public at present, and there is good reason to believe that the information on the subject available to the layman is extremely meager; even those rated as experts usually have a more or less theoretical conception of the diseases, their causation, remedies, and prevention, rather than actual experience with them. Until recently little attention has been given to prevention, and the usual attitude of the engineer, upon whom the main reliance for prevention ultimately must devolve, has been to let "sleeping dogs lie" or, more definitely, to "let well enough alone." However, the "laissez faire" attitude no longer is tenable, and in the past few years numerous conditions have caused those engaged in industry, including mining, to bring the subject before the public with a view to ascertaining the facts upon which to formulate remedial measures, primarily preventive.

Jan 1, 1935

By H. F. Weaver

The 19th National First-Aid and Mine Rescue Contest was held in the Civic Center, Charleston, w. Va., on October 2, 3, and 4, 1961. The meet was sponsored by the Bureau of Mines and the Joseph A. Holmes Safety Association, in cooperation with State mine inspection agencies, management and labor of the mineral extractive industries, and other groups interested in safety. The Arrangements Committee, as authorized by the General Committee, made the necessary arrangements for conducting the 1961 contest. Members of the Arrangements Committee were: George Trevorrow (chairman), Bituminous Coal Operators' Association; James B. Benson, Southern Coal Producers' Association; Charles Ferguson, United Mine Workers of America; Harry Gandy, Jr., National Coal Association; and James Westfield, Bureau of Mines.

Jan 1, 1962

By John J. Henn

As part of the U.S. Department of the Interior programs on rutile, authorized by the Office of Emergency Preparedness in June 1967 under provisions of the Defense Production Act, the Bureau of Mines reviewed available literature on major proposed processes for producing rutile substitutes. The processes are grouped according to the major processing step, and important operating features are described. Sixty-one references are cited.

Jan 1, 1970

By C. Lorimer Colburn

"The diverting of men from industry to combat in the world's war focused the attention of the operators in this country upon mechanical means of doing things. The demand for man-power -was so insistent that every available agency for multiplying it had to be employed. It was during the 1period of the war and immediately thereafter that development of the use of underground loading devices made most rapi4 progress. In all parts of the United States, mining engineers and mine managers were diligent in their efforts to develop mechanical loaders. The mining engineers of the U. S. Bureau of Mines in every section of the country have secured, with the cooperation of the mine operators, data on the actual performance of the mechanical shovels in their districts, and have made them available to the author of this paper.No effort has been made to discuss exhaustively the subject of underground loading devices. It has been the object to collect together in one paper, records of the performance of all machines now in actual use. Improvements in the design of machines are constantly being made the performance records given in this paper relate to operation prior to March 1 1 1921. The records prior to 1920 cay not fully represent the work that could be accomplished with the present models of the same machine.The data secured are given exactly as reported by the mine operators. Since this data were collected there have been two underground loaders, of a different design, put into operation in the iron mines of the Lake Superior District. One is the John Mayne Sub-level loader, being tried by the Cleveland-Cliffs Iron Co., Ishpeming, Mich., and the other is the Cole-Goudie shovel, being tried by the Oliver Mining Company, at Ironwood, Mich. No information has been secured regarding the performance of either of these machines."

Oct 1, 1921

By Karl C. Dean

All components of 15 automobiles manufactured between 1954 and 1965 were analyzed, and it was determined that a representative junk automobile would have the following composition (all figures in pounds): steel, 2,532; cast iron, 511; copper, 32; zinc, 54; aluminum, 51; lead, 20; rubber, 145; glass, 87; miscellaneous, 142. Time and motion studies and a cost evaluation were made to determine if such a typical vehicle could be economically burned in a smokeless incinerator and hand-dismantled, and if the resultant steel could be baled into a high-quality No. 2 bundle containing less than 0.10 percent copper. The cost evaluation showed that processing the composite car would cost about $51 to produce about $56 worth of marketable ferrous and nonferrous metal products and provide an annual rate of return on investment of 19 percent.

Jan 1, 1969

By J. J. Pfeiffer, J. W. Myers, A. A. Orning

A study was made of the feasibility of using washery refuse in the manufacture of lightweight aggregate for building materials . Preliminary caking and burning tests showed that the refuse could be converted into lightweight aggregate but that refuse passing a No. 14 U.S. Standard screen could not be used without additional processing . The aggregate was prepared by pelletizing the refuse and burning out the carbonaceous material on a chain- grate in a refractory - lined furnace . A small stationary - grate furnace was used to study the process variables involved and establish optimum ignition and combustion conditions . Maximum ignition rates were obtained at air rates of approximately 200 lb per sq ft hr , but air rates of 450 or higher were required in the burnout period to obtain temperatures high enough to sinter the ash . The data obtained from this unit were used as a guide in the operation of the chain- grate furnace . In the chain - grate furnace , satisfactory results were obtained by using primary air rates of 200 lb per sq ft hr in the ignition zone and 500 lb per sq ft hr in the burnout zone . The ignition- zone air was preheated to 500 ° F , but the air for burnout was not preheated . A total of 2-1/2 tons of aggregate was prepared in this unit and made into experimental block . A commercial development based upon the results of this study yielded a product which met the ASTM specifications C 130-42 for lightweight aggregate , and blocks made from the aggregate were of good color , durable , and light - inweight .

Jan 1, 1964

By J. Clark

The objective of this study has been to determine the state of the art in underground, thin-seam-mining systems, to identify new technology and procedures that would reduce the hazards of thin-seam mining and to recommend areas for further research. The study was carried out in two phases, the first of these being devoted to a survey of authoritative literature. Subsequently, the practices adopted in the various mining countries were analysed and comparisons made to identify machines and methods with the potential for application in the USA. Published figures on US bituminous coal reserves show the high proportion contained in thin seams and US accident statistics demonstrate that the risk is greater in thin-seam operations. A comparison has been made with the experiences of foreign operations. The Phase 11 study proceeded along two separate avenues to examine the distinctive problems associated with seam thicknesses above and below 30 in. Current systems of mining appropriate to seams greater than 30 in were elaborated and compared by means of a simulation exercise in terms of safety, production and cost. For seams below 30 in, less conventional systems, some presently disused, were studied and their potential evaluated; the research and development work necessary to make them viable has been indicated.

Jan 1, 1980

By Andrew B. Cecala

This U.S. Bureau of Mines report provides a detailed description of the Bureau-designed modified shearer clearer system. Engineering drawings are provided for all major components of this system. The modified shearer clearer system is a revised version of the original system and is intended to improve the ventilation around both cutting drums. The original shearer clearer technique was solely a dust control technique that has been effective in lowering shearer operators' dust exposures. The technique uses a series of water sprays that not only knock down a portion of the dust cloud but also act as small fans that move a substantial amount of air and keep the dust cloud from dispersing over the shearer body. The modified version is composed of two additional spray blocks for improved air movement around both cutting drums, thus lowering methane levels and the likelihood of an ignition. A laboratory study performed with the modified version in a full-scale longwall gallery resulted in a 73-pet reduction in methane concentrations at the shearer machine for both cut directions. The air-moving capabilities of the system provide more turbulence at the cutting drums and reduce methane levels.

Jan 1, 1994

By D. Harrington

For many years the Federal Bureau of Mines-in cooperation with other agencies-has been making investigations and compiling and publishing reports and statistics on accidents in the various branches of the mineral industry.4 Its assistance has been enlisted also in health, safety, and ventilation problems' incident to the driving of many large tunnels in the United States in recent years. As part of this work the Bureau has compiled considerable statistical and other information on accident experience in the tunneling branch of the heavy-construction industry. It has always been difficult to obtain up-to-date information on tunneling methods and tunnel accidents. Published accounts of tun¬nel construction furnish much interesting material of engineering, historical, or fiscal value, but usually little or no attempt is made to discuss and critically analyze the means taken to preserve the health and life of employees.

Jan 1, 1941

By Arno C. Fieldner

This is the fifth of a series of annual reports4/ of technologic investigations conducted by the Bureau of Mines on the occurrence, properties, mining, preparation, and uses of coal. The research of the Bureau is carefully coordinated with the requirements of the producing and consuming industries, with a view to conservation of resources of coal in mining and use, and conservation of the health and lives of workmen employed in these industries. Such coordination is facilitated by the wide range of specialization of the several groups on engaged in studies concerning coal. Here are reported correlated studies ranging from paleobotanic analysis of the formation of coal as it occurred some millions of years ago to the effect of mechanical methods of mining on present-day employment in mines. As this is a summary of the current work of the Bureau of Mines, so the Bureau likewise has provided a condensed review of the outstanding current work of others on research and technology of coal 5/.

Jan 1, 1940

Senior staff representatives of the Bureau of Mines and the National Institute for Occupational Safety and Health (NIOSH) met in Washington on September 6, 1972, to review and evaluate their cooperative accomplishments to date and to consider the planning and conduct of future coordinated activities. The six presentations given at this joint staff seminar are published here for the benefit of those concerned with the problems of coal mine health, and especially those with responsibilities in administering the Coal Mine Health and Safety Act of 1969.

Jan 1, 1972

By A. B. Hooker

A list of permissible mine equipment approved by the Bureau of Mines prior to January 1, 1940, was published as Information Circular 7207.3 Three supplements published as I. C. 7240,4 I. c. 7283,2/ and I. C. 73166/ completed the list of equipment available to January 1, 1945. The present list is a revision of the previous lists, together with the additional equip- ment approved from January 1, 1945, to January 1, 1947. In preparing this list, certain items have been omitted, either because the manufacturer is no longer in business or manufacture was discontinued several years ago. However, some discontinued equipments that are still in service and for which repair parts are available are marked with an asterisk to indicate their limited status. The remaining obsolete equipments are listed in tabular form in Appendix 1. Appendix 2 lists seven satisfactory fuels available for use in permissi- ble flame safety lamps and shows where the fuels are available. The equipments listed were approved only when inspection and tests showed that they met the minimum standards of safety as outlined in "schedules" based upon laboratory tests as well as on performance underground. This circular is published so that users and potential users may be in- formed of the many types of permissible equipment available for reducing hazards incidental to coal mining and as an aid in identifying the equipments.

Dec 1, 1947

By J. J. deBarbadillo

This Bureau of Mines report describes a process for recovering chromium and other metals from superalloy scrap. Laboratory-scale experiments were conducted to test a complex flowsheet utilizing a wide range of extractive metallurgical operations. The novel basis for the process is the fonnation of a sulfide matte in which chromium is concentrated in a discrete chromium sulfide phase. Mineral processing and hydrometallurgical procedures are used to separate chromium sulfide from the other matte constituents. The products of the process are a chromium-nickel alloy suitable for reuse in the superalloy industry, electrolytic nickel, electrolytic cobalt, and iron-molybdenum residue. Recovery of the principal elements contained in the scrap is chromium--93 percent, nickel--99 percent, cobalt--96 percent, and molybdenum--92 percent.

Jan 1, 1981

By P. M. Daling, C. A. Geffen

The objectives of this study were to examine a representative cross section of formal safety analysis techniques developed for the nuclear and aerospace industries, to recommend those methods that would be suitable for application to the mining industry, and to include those methods in a user's manual. Volume XI of this report, the user's manual, describes several methods that were determined to be immediately transferrable to the mining industry. The handbook gives detailed instructions on appropriate application and utilization of the methods. Other techniques will require further development before they can be effectively transferred to the mining industry.

Jan 1, 1983

By Wilbert J. Huff

[This is the fifth of a series of annual reports of the explosives Division, Bureau of Mines, United States Department of the Interior.3/ It deals particularly with work done during the period July 1, 1939, to June 30, 1939. The writer and the respective unit leader to whom credit is indicated have directed the various studies outlined.]

Jan 1, 1940

By Hewitt Wilson

Until recent years the term "whiting" was applied exclusively to the water-ground chalks of certain north European countries. In many industries these are still considered superior to the whiting made from domestic limestone and marble. However, the latter material has replaced much of the European whiting in the American market, largely due to improvements in grinding and classification by American manufacturers.4 To encourage the domestic industry, the Bureau of Mines in 1931 undertook a study of the preparation of whiting from American raw materials and a comparison of the finished products with European whitings.

Jan 1, 1937