Search Documents

By G. W. Center

This manual is intended to assist federal, state, and local regulatory and planning agencies, the mining industry and consulting engineers in determining the regulatory, environmental, technical and economic constraints influencing the site selection, planning, construction/operation and reclamation phases of a waste disposal facility. The information presented illustrates that factors affecting an individual site may be simple or very complex. This manual discusses methods for making future land use decisions, determining regulatory requirements, evaluating physical, chemical and structural properties of the disposed waste and selecting appropriate waste disposal methods and control techniques. Procedures and guides in the manual will assist personnel in assessing the complexities of waste disposal on a site specific basis. The major types of waste disposal systems are discussed and evaluated in terms of their advantages and disadvantages and applicability to varying site conditions and waste characteristics. Appropriate references following each chapter provide more detailed data on material presented in the text.

Jan 1, 1982

By Herbert H. Einstein

The thrust of research reported in Part I was to collect in-situ data from exploration programs and the published literature, and to empirically establish distributional patterns for these variables. Since discontinui¬ties in a rock mass govern to a large extent its engineering properties and thus the performance of any slope in the mass, work has been devoted to determining the appropriate distributional forms for attitude spacing and length of discontinuities and to distributional properties of resis¬tance and deformability parameters. The conclusion from these analyses is that trace lengths are logNormally distributed and that joint spacing is Exponentially distributed, regardless of orientation of the sampling line, and regardless of whether each joint set is considered separately or not. Joint orientation (attitude) data representing 22 individual joint sets from eight sites (a total or approximately 20,000 joints), do nor strongly support any of the commonly used distributions as broadly applicable in practice. The autocorrelation )f geometric joint properties is also examined. However, no significant spatial correlation could be found even after extensive data manipulation. The investigation of resistance and deformability parameters starts with a review of mechanisms and models that are used to represent them. Review and statistical evaluation of approxi¬mately 2,000 discontinuity shear tests has shown that good statistical estimates for use in reliability analyses can be obtained for friction angles.

Jan 1, 1979

By William J. Campbell

This analytical method development and evaluation was undertaken by the Bureau of Mines to provide accurate determinations of eight minor elements in low-alloy steels prepared from ferrous scrap. Fluorescent X-ray spectrography was the principal method investigated. Confirming analyses were made by conventional instrumental and chemical methods. All X-ray data were processed by a timesharing computer. No corrections were found necessary for inter-element effects or overlapping spectral lines. Concentrations were calculated from the least-square fit of a linear calibration equation derived from measurements on three sets of standard steels. These studies show that X-ray spectrographic analysis of lathe-finished surfaces provides accurate determinations of aluminum, copper, chromium, manganese, nickel, phosphorus, silicon, and tin.

Jan 1, 1973

By R. Hogg, T. F. Dumm

"Procedures for particle size analysis on respirable dust from coal mines have been evaluated. Using respirable dusts dispersed in a laboratory dust chamber, size distributions measured using cascade impactors have been compared with the results of a variety of laboratory sizing methods performed on samples collected on filters placed side-by-side with the impactors. The laboratory techniques included centrifugal sedimentation, laser diffraction/scattering and automatic particle counting. The general agreement among the various methods was very good, with systematic differences which can be attributed to the different definitions of size used. Simple conversion factors have been obtained which can be used to transform the laboratory data to equivalent aerodynamic sizes.Similar comparisons have been made on samples collected in underground coal mines. Again, the results are in quite good agreement although small discrepancies were observed in· some cases. These have been attributed to some degree of agglomeration in the airborne dust, leading to slightly coarser apparent distributions in the impactor samples INTRODUCTIONA primary goal of mine ventilation is the control of airborne dust, especially in the ""respirable"" size range, typically defined as finer than about 5 to 10 µm. It follows that determination of the amount and characteristics of the respirable dust is an important factor in evaluating the performance of ventilation systems. Particle size information on airborne dust in mines is commonly obtained by in- situ measurements using cascade impactors. However, these tend to be inconvenient for routine data collection and the alternative approach of collecting samples in the mine, on filters for example, and returning them to the laboratory for detailed analysis is very attractive. Questions have often been raised, on the other hand, as to the appropriateness of this approach. How well · do such laboratory methods describe the distribution of aerodynamic diameter of the airborne dust particles in the mine environment? The purpose of the work described in this paper was to evaluate some laboratory sizing methods and to compare the results of such measurements with the size data obtained by the direct, in-situ method."

Jan 1, 1989

By Edward D. Thimons

Several types of inflatable stoppings, developed under Bureau of Mines contract for use as mine air barriers during underground production, have been tested by the Bureau. All of the stoppings tested showed significant internal leakage initially but, in all but one stopping, the leaks were sealed with limited effort The stoppings were tested underground in two western noncoal mines under production conditions. The results from the Colorado molybdenum mine showed the stoppings to be generally unsatisfactory for daily mine usage if they are deployed near blasting areas or in locations where near-perfect air seals are required. They were very susceptible to blast damage and seldom were better than 90 percent efficient as air barriers. However, stoppings tested in the New Mexico uranium mine were located substantially distant from any blasting. Because slight leakage past the stoppings was acceptable, they proved very satisfactory in that application.

Jan 1, 1976

By F. E. Armstrong

This report describes development and application by the Bureau of Mines of techniques and instruments for using radioactive inert-gas tracers to determine flow paths through petroleum reservoirs that have natural fracture systems and for which water injection has been selected as the stimulative production method. A field test was made to prove the techniques and evaluate instrumentation. The feasibility of applying the techniques and instruments to the solution of reservoir problems in other stimulative methods of production also is discussed. Oil commonly is displaced from sandstone host rocks by the action of a driving force that causes the oil to move through interstices of the rock and into production wells. In addition to the requirements of oil being trapped within the sand pores and the presence of an effective displacement mechanism, the rock itself must have adequate permeability to permit flow of oil and other fluids.

Jan 1, 1961

By C. D. Litton

This Bureau of Mines report presents a set of guidelines for determining the distribution of product-of-combustion fire sensors in underground mines. Sensor spacing is defined in terms of sensor alarm threshold, ventilation flow rate, and mine entry dimensions. Sensor spacing guidelines are presented for detection of fires from two primary combustibles, coal and wood, which are common to the majority of underground mines. The guidelines are based on data from full-scale and intermediate-scale fire tests conducted by the Bureau of Mines.

Jan 1, 1983

By R. Hogg, T. H. Dumm

"The mathematical treatments used in the evaluation of particle size distribution from pipet-withdrawal centrifuge data are reviewed. An error in the published procedure for multiple-sample withdrawal systems is pointed out and a corrected formulation is presented. An alternative treatment, based on a piece-wise linearization of the size distribution is described. Computer simulations of the analytical and data evaluation procedures indicate that the errors in the original formulation are not generally serious and that the corrected and alternative procedures lead to very similar estimates. Except for some cases involving very narrow size distributions, the alternative approach appears to give slightly closer estimates of the size distribution. Comparisons based on actual experimental data are also described.1 IntroductionSedimentation methods are widely used for the determination of particle size distributions. The procedures are relatively simple to use and the results are essentially absolute, requiring no external calibration. Gravity sedimentation is typically applicable to particles in the size range of about I to 50 pm and generally involves measurement of the relative concentration of particles as a function of depth and time in a dilute suspension. Particle size is calculated using Stokes, law:"

Mar 1, 1989

By A. G. Galaitsis

The two volumes of this report summarize the noise control work performed by BBN on a rail personnel carrier operated in coal mines. Volume I of the report - submitted November 1977 - describes the aboveground work performed to identify the noise sources, design, fabricate, and install the treatments, and evaluate the treatments through noise and vibration tests. The current volume (II)-describes the underground work conducted by BBN to determine the deterioration, if any, of the treatments when the vehicle is operated normally in a mine. There were no significant changes in the acoustical performance or mechanical integrity of the treatments at the end of a three-month period.

Jan 1, 1980

By R. L. Handy

The goal of this research was to adapt the highly successful rock borehole shear test for use in deep, small-diameter boreholes. Operating somewhat on the principle of a rock bolt, the borehole shear test measures both the expansion pressure and pulling force to give discrete measures of rock shearing strength as a function of the applied normal pressure. A new instrument was designed and built to fit into a 2-3/8 inch diameter hole. Unfortunately the design became so complicated, the operation is nut reliable. This is attributed to constraints of the small hole, and added requirements of an in-hole anchor to push against, and a rotating shear plate cleaner for repeated tests down-hole. A clue to the d: vice complexity is its length, which is over 10 feet. Furthermore it employs concentric cylinders and one hydraulic cylinder bored into the piston of another, or it would be even longer. Meanwhile drilling technology has advanced to greatly reduce costs of drilling 5- or 6-inch diameter holes. The downhole tester therefore should be redesigned and simplified for use in a larger diameter drill hole.

Jan 1, 1982

By A. R. T. Denues

"INTRODUCTION The orienting phases of the current investigation of cushioned blasting in the Explosives Division of the Bureau of Mines were indicated in a previous publication (5) 3/. Pertinent literature reviewed therein indicated a highly controversial field. This emphasized the need for experimental studies of many factors that affect the health and safety of miners and the efficiency of mining operations. Results of some orienting tests showed marked effects on practical hazards. Further, they emphasized the necessity and importance of the contemplated investigation. The scope and general plan of these practical inquiries into the safety of cushioned blasting were indicated.This investigation of cushioned blasting relates to the various means employed to reduce the intensity of application of energy from explosive actions in boreholes. It has been suggested (from p. 19 of reference 5) that the divisions of this work would correspond to the salient hazards affected by cushioned blasting. These include the ignition hazard, hazards from poisonous gases, and other practical hazards in the blasting technique. The ignition hazard was resolved into two components of approximately equal weight. These include studies of effects upon (1) the incendivity of blown-out shots and upon (2) the occurrence of such shots. Experimental studies of effects on the incendivity of blown-out shots were first undertaken. Questions of the best procedure for making these evaluations have been adduced, and the interpretation and utilization of the results of gallery testing seemed to require detailed attention; some preliminary general considerations of such testing were therefore necessary."

Jan 1, 1943

By William H. Schiffbauer

This report details a microcomputer-based control and monitoring network that was developed in-house by the U.S. Bureau of Mines and installed on a continuous mining machine. The network consists of microcomputers that are connected together via a single twisted-pair cable. Each microcomputer was developed to provide a particular function in the control process. Machine-mounted microcomputers, in conjunction with the appropriate sensors, provide closed-loop control of the machine, navigation, and environmental monitoring. Off-the-machine microcomputers provide remote control of the machine, sensor status, and a connection to the network so that external computers can access network data and control the continuous mining machine. Because of the network's generic structure, it can be installed on most mining machines.

Jan 1, 1993

By M. D. Aldridge

The results of a four-year research effort aimed at developing a practical and effective electronic system for monitoring safety conditions throughout a coal mine by displaying, at a central location, remotely measured parameters are described. This document presents the general philosophy of an experimental system in an operating coal mine. The conclusions drawn from this experience are presented and a typical design for a large coal mine is described.

Jan 1, 1974

By Mackenzie Burnett

The Brattice Window Method was used to measure the leakage rates of a total of 42 ventilation stoppings in 8 hardrock mines. Various types of stopping construction were evaluated. The following types are listed in order of decreasing effectiveness: 1) Cinder block, 2) Timber and mortar, 3) Timber and polyurethane foam, and 4) Timber and brattice material. There are slight differences in the effectiveness of the first three types, while the timber and brattice type is substantially inferior to the others. The repeatability of the Brattice Window Method was found to vary with physical conditions in the mine such as stopping location with respect to intersections, regularity of drift cross section, and the presence of hardware such as air and water pipes, timber sets and wire mesh. The Brattice Window Method is viewed primarily as a tool for estimating and comparing stopping leakages for the purpose of determining where repair efforts should be concentrated. A laboratory test program resulted in the derivation of several "rules of thumb" for employing the Brattice Window Method, which will aid in securing accurate and repeatable data.

Jan 1, 1979

By Gordon T. Austin

The combined value of production of natural abrasives, which include tripoli, special silica stone, garnet, staurolite, and emery, increased about 4% in 1990. The increase in the value of tripoli production was the result of an increase in the unit value. Emery increased owing to an in? crease in the volume of the material produced and an increase in the unit value. Special silica stone experienced a decrease in unit value and an increase in the quantity produced. Garnet showed a 10% in? crease in quantity and a 73% increase in unit value. Staurolite decreased about 8% in the quantity produced, and the value of production decreased about 10%. The fused aluminum oxide industry showed a 5% decline in the quantity produced and in the value of production. The silicon carbide industry saw a 10% decrease in the quantity produced and a 9% decrease in the value of production. Production for both industries decreased 7% in quantity and value compared with those of 1989.

Jan 1, 1993

By R. A. Isberg

This report describes the design and implementation of UHF radio and closed-circuit television systems in the Black River room and pillar limestone mine near Butler, Pendleton County, Kentucky. Prior to designing the radio system, measurements of signal attenuation on 812 and 466 mHz were made in the slope tunnel and in the straight and level crosscuts in the mine. Two distributed antenna systems fed by two sets of base stations provide approximately 75o coverage of the mine. Passive reflectors are used for extending signals into intersecting crosscuts and two-way signal boosters will be used to extend signals to the perimeter and obstructed areas of the mine. Fourteen mine vehicles were equipped with mobile radios equipped with digital identification, alarm and status encoders. Fifteen portable transceivers also were used. Six closed-circuit television cameras provide surveillance of critical transfer points of the belt conveyor system, and the loading dock at the base of the slope and an ash disposal area in the mine. Two-way radio communication and closed-circuit television have saved considerable man. hours, increased production, reduced maintenance costs and enhanced safety. Innovative developments were the use of passive reflectors and two-way signal boosters for extending signals into intersecting crosscuts, development of lightweight signal margin measuring equipment, modifications of mobile digital encoders to automatically send status information from mine vehicles such as numbers of loads of ore delivered, hot engine, etc., and the use of CATV technology for multiplexing audio, digital and video signals onto coaxial cables from the surface to the mine.

Jan 1, 1981

By James J. Snodgrass

The Bureau of Mines designed and constructed a series of calibration models for geophysical borehole logging. A nominal hole diameter of 3 inches was selected as representative of typical core holes drilled for mining and engineering purposes, although additional hole diameters of 2, 5, and 8 inches are provided in one of the models for determination of empirical correction factors for variations in hole diameter. The physical properties of the models were determined by laboratory analyses of drill core samples and evaluated statistically for reliability. This report outlines the location of the models, elements of design and construction, and results of the laboratory tests. The models are available at the Denver Federal Center, Denver, Colo., for use by Government agencies and private industry to calibrate logging equipment for measurements of density, sonic velocity, magnetic susceptibility, and electrical resistivity.

Jan 1, 1976

By H. F. Yancey

Although a general relationship exists between the two criteria used to measure sharpness of separation -error area and probable error -they sometimes give quite different appraisals of a particular washing operation. Error area takes into account how the entire raw coal was treated, whereas probable error reflects only how the material of intermediate density was separated, ignoring completely the recovery of clean coal and the rejection of heavy impurity. Error area is thus more reliable for general use. In heavy-medium cleaning, sharpness of separation decreases with increase in separating density, but ordinarily the change is not great enough to affect the yield and ash content of washed coal measurably. Therefore, distribution curves for heavy-medium units can be transposed from one separating density to another, at least in the range of separating densities ordinarily used in the United States.

Jan 1, 1955

By R. W. Bee

This project, sponsored by the U.S. Bureau of Mines, Division of Environment, addresses two major subjects: refuse removal and subsidence monitoring. The refuse removal task consisted of developing a methodology for selecting the most economical combinations of coal mine breaker refuse and rock banks, disposal sites and material moving systems (trucks, trains, belt conveyers and pipelines). To prepare plans for moving refuse in the Lackawanna Valley of Northeastern Pennsylvania, refuse banks were inventoried, underground disposal sites identified and unit cost data prepared for the various material moving systems. The subsidence monitoring task consisted of defining the phenomenon of coal mine induced surface subsidence, establishing operational requirements, cataloging sensors and techniques to detect and measure subsidence and testing of the most promising techniques (photoelastic patch, tiltmeter, strain gage, microseismic and precise surveying). A preliminary system for a 700 acre area in Scranton utilizing 267 grid sensors, seven microseismic sensors and precise surveying techniques was designed with initial and annual operating costs determined. Two minor tasks supported both main subjects: zoning in the Northern Anthracite Field of Pennsylvania and Technology Transfer of subsidence vulnerability prediction techniques.

Jan 1, 1972

By Slavoljub Makslmovic

One important element of the U.S. Bureau of Mines computer-assisted mining research program is the development of a reliable coal interface detection (CID) system. Several candidate CID concepts currently being investigated by the Bureau include use of natural gamma radiation (NGR), vibration, passive infrared, video, and radar. To help establish which CID sensor technologies need to be developed for a given seam, the Bureau has collected geological and mining practices data from over 460 underground and surface mines in the United States. Also, over 500 coal and rock samples have been obtained for laboratory analyses of ash content, sulfur content, heating value, and NGR. The Bureau's findings indicate that the immediate roof strata in 81% of the underground mines and 93% of the surface mines are made up of shale, draw slate, or claystone. The immediate floor strata in 88% of both the underground and surface mines consist of fireclay, shale, draw slate, or claystone. The results of the NGR testing indicate that the NGR method appears to be a potentially useful CID tool, provided that the immediate roof and floor are both composed of a high percentage of shale-type material.

Jan 1, 1993