Search Documents

By S. K. R. Iyengar

This report presents the results of a study to develop optimal designs for light-weight mine roof supports for use in underground coal mines. A load capacity of 196 kN (22 tons) and a height adjustable between 1.829 m (72 inches) and 2.438 m (96 inches) were taken as the design parameters and the design goal was a unit weighing less than 22.3 kg (50 lbs). Three alternative design concepts were explored, viz. mechanical, hydraulic, and hydro-mechanical and a total of 13 designs analyzed in detail. Steel, aluminum alloy and composites were the main potential construction materials investigated for suitability from structural, life, and safety and other considerations. The designs considered most promising for development were: (i) the mechanical screw-pin type using telescopic tubes and a fine adjustment screw thread section (ii) the all-hydraulic type, of steel, aluminum alloy or aramid graphite construction (iii) the hydro-mechanical design using telescopic tubes and a short stroke hydraulic cylinder for fine adjustment It is shown that by using realistic mathematical models for stress and deflection calculations, it is possible to reduce prop weight to the design goal. The analysis presented for all-hydraulic props is applicable to hydraulic cylinders on all mining equipment and similar machinery. This report includes the computer program and user's guide for analyzing hydraulic cylinders as well as a cross-indexed bibliography on structural composites.

Jan 1, 1978

By Gordon R. Sima

The contract is concerned with feasibility studies, design and fabrication of a group of prototype hand-held test instruments and machine-mounted test instruments for measurement of electrical shock hazards of mining machines. An instrument for use in open pit mining machine ground wire verification was proposed, developed, built, and tested. This report presents the design and operational theory of the open pit instrument as well as information on the program to improve the original prototype hand-held machine-mounted test instruments.

Jan 1, 1977

By Ernest A. Curth

Statistics For 1956-66 show that mine transportation accidents accounted for 19 percent of fatalities in bituminous coal mines, second only to roof deficiencies as a cause of death. Productivity per man-shift increased from 10.2 tons in 1956 to 18.4 tons in 1966, but the fatalities per million man- hours of exposure also increased from 0.19 to 0.21 during that same period, indicating that transportation hazards still persist. Consequently, the Bureau of Mines reviewed the transportation fatalities that occurred in bituminous coal mines during 1956-66. The data were processed by computer to find what constitute hazardous conditions and unsafe actions as well as to correlate occupation and age of victims, transportation type, and mine production. Environmental factors and equipment defects which create hazards, as well as unsafe actions of personnel, were determined for each type of mine transportation: Track haulage, mobile nonrail haulage, conveyors, hoists, automotive operations, and front -end loaders, and for transfer stations (loading points, slope and shaft bottoms, surface transfers) and railroad yards. Man-trip accidents, a group with a catastrophe potential, also were analyzed. The basic design and operational features of each transportation type were outlined and procedures considered safe in the light of accident experience were suggested. Findings show that unsafe actions of personnel and hazards created by environmental deficiencies or equipment malfunctions contribute equally in causing transportation accidents. Accordingly efforts should be directed toward improving working conditions, equipment maintenance, and education and training of employees. The trend is toward using safer modes of transportation, notably conveyors. More attention should be given to track haulage operation, railroad yards, and nondestructive field testing of materials.

Jan 1, 1971

In 1960, the Secretary of the Interior, acting under the provisions of Public Law 454, 80th Congress, appointed a Lignite Advisory Committee to aid in programming research on coal (lignite) of the north-central area. The chairman of this committee is the Secretary of the Interior or his delegated representative, and in all meetings held during 1960 and 1961, the Director of the Bureau of Mines, Marling J. Ankeny, has presided. The members of this committee were R. W. Rovelstad, President, Baukol-Noonan, Inc., Noonan, N. Dak. W. E. Keller, Vice President, Northwest Division, Truax-Traer Coal Co., Minneapolis, Minn. A. M. Cooley, Professor of Chemical Engineering, University of North Dakota, Grand Forks; N. Dak.

Jan 1, 1963

By Henry Kreisinger, John Blizard, B. J. CROSS, C. E. Augustine

This report gives the results of 26 tests of a four-pass Edgemoor boiler fired with powdered coal at the Lakeside station of the Milwaukee Electric Railway & Light Co. The tests were made by the fuel section of the Bureau of Mines in cooperation with the research department of the Combustion Engineering Corporation and the operating department of the Milwaukee Electric Railway & Light Co. The object of the tests was to determine the thermal efficiencies and capacities obtainable by burning powdered coal under large central-station boilers, and the possibility of operating such boilers continuously at high efficiency and capacity without destructive effect on the furnaces and without difficulties in refuse removal. In any system for burning pulverized coal the furnace is the most important part because, to justify the cost of pulverizing, the powdered coal must be burned with higher efficiency than coal fired with mechanical stokers. In other words, it is the furnace that by giving higher thermal efficiency must pay for the installation, maintenance, and operation of the pulverizing equipment. No matter how simple the apparatus for the preparation of pulverized coal may be, or how simple the pulverizing process, unless the furnace is so designed that it can be operated continuously with high thermal efficiency, the whole system is a failure. For high thermal efficiency the coal must be burned almost completely with low excess air. But low excess air and complete combustion give high furnace temperature, which in turn causes erosion of the furnace lining and fusion of the ash; and removal of the fused ash is difficult. The necessity of complete combustion with low excess air thus brings with it these two important problems in the design of a furnace for burning powdered coal: 1, Prevention of erosion of the furnace lining; 2, easy removal of refuse from the furnace. For the purpose of solving these problems, the boiler tested was equipped with a furnace having hollow walls, through which about 60 per cent of the air needed for combustion passed before it entered the furnace. By passing through the hollow walls, the air cooled the furnace lining and prevented excessive erosion. A water screen was placed in the furnace about 3 feet above the bottom to keep the refuse deposited at the bottom from fusing and to make its removal easy. The design of the furnace, water screen, and burners was based on the experience gained in the previous cooperative tests1 with a smaller furnace, experimental water screen, and burners at the Oneida Street station of the Milwaukee Electric Railway & Light Co. The boiler tested had 13,057 square feet of heating surface. It was one of eight boilers fired with powdered coal, and was designated as boiler No. 8. The Lakeside station is the largest central station in the world that burns powdered coal exclusively. The coal used in the first five tests came from Illinois. The fuel in the other tests -:vas a mixture of Illinois and Pittsburgh coals.

Jan 1, 1925

By R. A. Guereca

Preliminary to an experimental study of selected physical properties of helium and related gases) the Bureau of Mines Helium Research Center conducted a data-gathering literature survey. This report combines the results of the 1961-63 literature search into a usable format. The data accumulated on the physical properties are presented in tables and graphs. The data in the tables were chosen for exact representation and comparison of specific values. An attempt was made to select the most reliable and consistent value available for a given property without extensively analyzing each source reference. The methods of evaluation are discussed later. The graphs show trends and anomalies which may be obscure in tabular form. (Reprints of the graphs) with the scale grid enlarged 2 1/2 times) are available upon request through the Research Director) Helium Research Center.) The literature search was conducted using Chemical Abstracts as the primary reference source with additional information drawn from Applied Science and Technology Index) Chemical Reviews) Physics Review) Science Abstracts (Physics») and other abstracting services. Part of the data included in this report have been tabulated previously by others (£-1).5 In a few areas) the sources of information are scarce and obscure (for example) refractive index and dielectric constant). The search was extensive; however) some sources

Jan 1, 1967

By J. P. Morris

A diphenyl ether calorimeter for measuring high-temperature heat contents of ferrous alloys and iron-and steelmaking slags was constructed and calibrated with specimens of molybdenum, alumina, and platinum that were heated to temperatures ranging from 1,720° to 1,875° K. The standard deviation of the calibration measurements was 0.37 percent. By measurements of the enthalpy of delta and liquid iron, the heat of fusion of iron was found to be 3,298 ±100 cal per mole.

Jan 1, 1966

By Raymond W. Hiteshue

To aid in designing a continuous system for evaluating processes for converting coal to high-Btu gas] the Bureau of Mines determined the amenability of various coals and a char to hydrogasification at 800° C and 6,000 psig using a molybdenum catalyst. A lignite from Rockdale, Tex., an hvCb coal from Rock Springs, Wyo., a char from the low-temperature carbonization of the latter, an hvAb coal from Pittsburgh, Pa., and an anthracite from Luzerne County, Pa., were selected. Highest yields of gaseous hydrocarbons, 94 pet, based on maf feed, were produced from char, and lowest yields, 67 pct, were obtained from lignite. Hydrocarbon gases contained 82 to 92 pct methane, 8 to 15 pct ethane; and 1 to 3 pct propane.

Jan 1, 1962

By Maria I. De Rosa

Combustible materials, when burned, produce toxic gases and smoke, which may vary dramatically from one material to another, with resultant different total toxicity and smoke obscuration levels. This U.S. Bureau of Mines report presents smoke property data acquired for a variety of mine combustibles and shows that there exists a correlation between the smoke properties, the relative toxicity, and the smoke obscuration levels of those combustibles tested. These correlations can be used to devise simple, standard tests for determining the toxic and smoke obscuration hazards of mine materials during fire.

Jan 1, 1989

By David J. Kusler

This report describes a primary or direct, continuously sampling, and automatically averaging gravimetric method for analyzing gaseous mixtures of carbon dioxide, carbon monoxide) hydrogen, and (by volume measurement) nitrogen. The gaseous mixture is analyzed by passing it at a controlled and definite rate through a system that permits carbon dioxide and water retained by appropriate absorbents to be determined and the residual-gas volume (essentially nitrogen) to be measured. The accuracy and dependability have been established by comparison with very carefully conducted Orsat analyses. The method was developed for, and has been satisfactorily applied to, the analysis of blast-furnace top gas. It permits relatively attention free operation, using simple and low-cost materials usually found as basic equipment in the analytical laboratory. It provides, over a wide range of time or sampling intervals (from less than 1 to over 24 hours), the average composition, in terms of volume-percent, for those components usually determined in blast-furnace gas, if (as is usual) the flow rate of gas from the blast furnace is essentially constant over a selected analysis interval. Oxygen and methane are not determined; but, since these gases are normally absent or present only in traces, their analysis is seldom required.

Jan 1, 1959

By Lee M. Manna

This report summarizes the program to design, fabricate, install and preliminary test a pneumatic braking system for 10-ton mine haulage cars. Major arrangement drawings are reproduced, pneumatic schematics, parts list and actual developed costs. Recommendations as to system improvements are made.

Jan 1, 1977

By Richard C. Wang

The U.S. Bureau of Mines established a wire rope research laboratory to examine the factors that affect the safety and the useful life of wire rope. In the most recent work, two 32-mm 6x27H flattened strand ropes were degraded on a bending fatigue machine. The two tests were run at constant loads of 285 and 347 kN or safety factors of 2.5 and 2. Nondestructive and tensile strength tests were performed on samples of the ropes to determine the relationship between rope deterioration and rope breaking strength. Neither the area loss nor the number of broken wires measured from nondestructive tests could be used as clear indicators of the loss of strength. However, it was found from the tensile tests for both rope specimens that the strength loss was associated with the reduction of breaking strain. This suggests that measuring the strain of many short sections of a rope in the elastic region may locate the high stress sections and thus delermine the condition of the rope.

Jan 1, 2010

By Dennis A. Long

Slip and fall accidents are a major cause of lost-time injuries associated with large mobile equipment in surface mines. An evaluation of the safety hazards associated with getting on and off large surface mining vehicles showed that most of the accidents occur at the point where personnel attempt to mount or dismount the machine at ground level. The major hazardous design conditions were identified as excessively flexible supports for lower steps or rungs, inappropriate ground-level-to-first-step distances, poor step designs, access designs that use vehicle components as steps or walkways, and inadequate hand- rail and guardrail designs, Additional hazards are introduced by the lack of proper maintenance of ladder hardware and the work practices of operators in carrying articles while mounting and dismounting the vehicle. This Bureau of Mines report describes the design and in-mine testing of improved access system for large mobile mining equipment.

Jan 1, 1984

By C. A. Komar

Laboratory-scale hydraulic fracture tests were conducted by the Bureau of Mines on directionally oriented sandstone material, along with measurements of directional rock properties such as tensile strength, permeability, ultrasonic velocity, and dynamic elastic constants. In these tests, fracture orientation was determined as a function of various combinations of stress, rock saturation, rate of borehole pressurization, and direction of minimum tensile strength relative to minimum horizontal compressive stress. The objective of the experiment was to investigate whether horizontal stresses always controlled the orientation of induced vertical hydraulic fractures, or if under conditions of small differences in stress and/or slow borehole pressurization rates, the induced fracture direction was influenced by directional properties of the rock matrix. This study shows that the expected influence of horizontal earth stress on the orientation of an induced hydraulic fracture becomes negligible when¬ever the magnitude of the difference between the compressive stresses is 200 psi or less. When this occurs, fracture orientation is controlled by the directional properties of the rock--primarily permeability and tensile strength.

Jan 1, 1973

By Charles R. Harrison

The purpose of this study and resulting development of the training program, "Safety--Let's Make It Happen" was to determine the relation of concepts to the development of desired Health and Safety behavior. After extensive pre-contract study, it was hypothesized that improved acceptance and understanding of the Federal Coal Mine Health and Safety Act of 1969 could possibly contribute to the reduction of accidents. Second, in order for an individual to accept and understand the Act, he or she must have a working knowledge of its purposes and application. Third, acceptance and understanding of the Act, necessary to protect the individual from negligence, was imperative. Fourth, an actual operating company could provide the base in which to test these hypotheses in a meaningful manner and develop this type of training program. Six assumptions were agreed upon before embarking on this study and training program development. (1) In the cognitive process, a concept introduction into an individual's personality may result in a behavior quite different than if he or she had been exposed to a different concept.

Jan 1, 1977

By R. H. Jefferson

An electrochemical method to selectively determine sulfur dioxide in the presence of sulfur trioxide was investigated. A hydrophobic gas-permeable membrane separates the gas sample solution from an internal filling solution containing a fixed quantity of chloride ion and a sufficiently large excess of sodium bisulfite so that its concentration may be considered constant. Sulfur dioxide diffuses through the membrane to dissolve in the internal filling solution and liberates an equivalent quantity of hydrogen ions. The electromotive force between a precision-ground, flat-ended pH electrode, which acts as the sensing element, and a chloride sensing electrode, which acts as the reference element, gives a direct measure of S02 in the gas sample solution. Calibration curves in water, tetrachloromercurate (TCM) , and citrate buffer absorption solutions were closely parallel with slopes in their linear segments, ranging from 57 to 52 mv/decade of S02 concentration. The slopes compare reasonably well with the theoretically expected slope of 58 millivolts at 21° C. The water standard curve was linear with respect to the logarithm of S02 concentration from 1 to 1,000 ppm S02; the TCM standard curve was linear from 10 to 2,000 ppm S02; and the citrate standard curve was linear from 30 to 5,000 ppm S02' The high efficiency and nontoxicity of citrate favor it as a substitute for the conventionally used TCM in the absorption solution.

Jan 1, 1976

By V. R. Miller

The Bureau of Mines investigated methods for testing the tensile and sheer strength of cast specimens of bulk solder and of soldered joints in order to increase the strength and extend the useful temperature range of soft solders. A spread-area test for determining the wettability of solder on copper surfaces was developed. Mannitol was used as a flux in spread tests to control spreading and to avoid plating, etching, and other side effects of regular fluxes. Data on commercial and high-purity solders obtained by these methods show more consistency than those reported by others from similar tests.

Jan 1, 1967

By J. B. Zink, M. J. Peterson

A semiquantitative spectrochemical method was developed and applied to the analysis of ash of U.S. coals . A low- temperature ashing procedure was used to minimize the loss of volatile elements . The analytical procedure provides for the estimation of 68 elements including major , minor , and trace constituents . Standards for the trace elements were prepared in a synthetic base mixture that approximates the average composition of U.S. coal ashes . Excitation was achieved with a d- c arc , spectra were recorded photographically , and interpretation was made by visual comparison of spectra of unknowns with spectra of graded standards series . Thirty- six trace elements were found in the analysis of 900 samples . Details of the procedure are presented , including sample and standards preparation , excitation and exposure conditions , spectral lines used , and approximate limits of detectability .

Jan 1, 1964

By F. E. Block, Stephen D. Hill

The necessity for measuring radiation dose is encountered in studying both the beneficial and damaging effects of ionizing radiation on materials . It is also necessary to know the radiation dose absorbed by the reactants in order to evaluate the efficiency of reactions or processes that are promoted by radiation . Thus , a significant effort was made at the Albany cobalt 60 facility to investigate techniques by which the exposure radiation dose can be determined . Methods including ferrous sulfate , ceric sulfate , and methyl methacrylate chemical dosimeters , ion chamber dosimetry , and an absolute radiation calorimeter were investigated . Isodose curves were constructed for several standard source configurations using the dosimetry techniques which were investigated .

Jan 1, 1964

By H. C. Carpenter

Lignite tar made by low-temperature Lurgi-Spülgas carbonization of North Dakota lignite was hydrocracked in single-pass, fixed-bed operation at 3,000 pounds per square inch over cobalt molybdate catalyst to produce gasoline, and at the same pressure, over zinc chromite catalyst to crack the high-boiling phenolic compounds to low-boiling phenolics. Hydrocracking the raw tar or the creosote-oil fraction from the tar over cobalt molybdate removed most of the oxygen, sulfur, and nitrogen in the forms of water, hydrogen sulfide, and ammonia, and produced gasoline yields from 31 to 59 volume-percent. The gasoline fractions contained from 0.1 to 7.7 volume-percent tar acids, but tar-base percentages were too low for reliable measurement; removal of these materials with dilute caustic and acid solutions also reduced the sulfur and nitrogen to 0.01 weight-percent or less.

Jan 1, 1963