Search Documents

By J. H. Welsh

This Bureau of Mines report presents guidelines to be considered in the design, installation, and operation of environmental mine monitoring systems in underground coal mines so as to enhance safety in the U.S. mining industry. A review of the current status of mine monitoring in the United States is also provided.

Jan 1, 1987

By B. J. Moore

This publication contains 14,242 analyses of gas samples from oil and gas wells and natural gas pipelines in 40 States and 24 foreign countries. These gas samples were collected in the period 1917-85 as part of the Bureau of Mines survey for helium occurrences. The gas analyses contained herein were made by several methods over the period covered. Analytical work on samples collected early in the period was done on the Orsat apparatus. The one-cut apparatus and four-cut fractional distillation equipment were added later. A mass spectrometer was acquired in 1949 and used for all gas analyses made after that time. From 1917 to 1978, helium analyses were made on special helium analytical equipment designed and built by the Bureau of Mines Helium Operations Laboratory. In 1978, this apparatus was replaced in the quantitative helium analysis work by a gas chromatograph.

Jan 1, 1987

By Glen C. Ware

The Bureau of Mines determined the factors involved in the corrosion of starting sheets used in the production of electrolytic zinc with the ultimate purpose of adapting zinc starting sheets to commercial practice . Under present practice , zinc is electrodeposited on aluminum cathodes and subsequently stripped for melting . The use of zinc instead of aluminum would eliminate the need to strip the deposit , thereby reducing the cost of handling and melting it , but zinc has not been suitable because it was too vulnerable to the corrosive attack of the electrolyte . Serious attack was found to be limited to the areas of the cathodes situated immediately above the surface of the electrolyte and to re - entrant corners . It was possible to avoid solution - level corrosion by immersing the starting sheets completely , exposing only a relatively heavy suspension member to solution - level attack . Zinc starting sheets could be made as reliable as aluminum and could be continued in residence for periods up to 39 days . Periods as long as a week were feasible under conditions similar to those found in commercial practice . A test of zirconium as a starting - sheet material showed that it promoted corrosion of the deposit to a lesser extent than aluminum and that the deposit adhered less tenaciously . These two properties lend themselves to the development of ways to strip deposits mechanically from zirconium starting sheets . Titanium was unsuitable for use as a starting - sheet material .

Jan 1, 1963

By Kyle W. Charlton

The Bureau of Mines utilizes special testing methods for the analysis of underground mine atmospheres for use during or after mine disasters and fires. These methods depend upon drawing sample gas to the surface through multiple tube bundles with the subsequent analysis of grab samples or the automatic analysis by often remotely located instruments on a continuous, 24-hour basis. During cold weather, low ambient temperature causes condensation and freezing of condensable vapors in the sample which can result in delayed response times or complete blockage of the sample line. This report covers research and resulting development conducted by the Bureau of Mines to produce a reliable method to selectively remove condensable vapors and particulate in the sample gas stream under worst-case field conditions. The effort resulted in two prototype systems which have greater field utility than originally anticipated. The innovative project resulted in two patent applications submitted through the Bureau of Mines.

Jan 1, 1981

By WILLARD W. CUTLER

This bulletin reviews, in the light of recent experience, the use of production-decline curves in estimating the future production of oil from wells. It deals with the estimation of the reserves of recoverable oil in properties already producing or in those adjacent to them, takes cognizance of the physical laws governing expulsion of oil from oil sands, and shows how the production-decline curve can be made to utilize these laws in estimating reserves and rates of production. The valuation of oil properties should be based on the total amount of oil recoverable from a property by the methods in use, the rate of recovery, the cost of production, and the selling price. Numerous other curves besides those for reserves and rates of production may be formed from the production-decline curve and will present desired information in a convenient time-saving form. These curves also are described. Methods developed before the production-decline curve method was used are briefly discussed in order that the principles on which estimations of oil reserves are based may be made plain. The construction of curves and tables for estimating future production of individual wells and of average wells in most of the important oil districts of the United States is described and operating problems that may be solved by the use of production-decline curves are discussed. The bulletin does not deal with costs, oil prices, or the methods of evaluating oil properties. Many engineers have amply demonstrated the value of the production- decline curve method by forecasting within reasonable limits the production of many thousands of wells and tracts. The value of similar estimates depends however, on (1) the application of trustworthy methods; (2) the care and judgment of the estimator; and (3) the length and reliability of the records and the accuracy of ofher information used in estimating future production. When adequate records and information are available, experience has shown that It qualified engineer can forecast production far more accurately than has been deemed possible, except where the usual conditions governing the expulsion of oil from a sand have been radically changed by applying compressed air or by flooding with water, or, to a less degree, by using vacuum. In general, the production-decline curve method, though there are limits to its accuracy, is far more trustworthy than any other.

Jan 1, 1924

By H. E. Peterson

A study was undertaken by the Bureau of Mines to develop a simple, reliable test for field detection of selenium in rocks and soils. Two methods are described for qualitative detection of selenium, dependent upon its form of occurrence and the presence of interfering constituents in the sample. Both methods involve fusion of the sample in a test tube to form elemental selenium that will volatilize and condense as a red deposit on the cooler upper portion of the test tube. The methods are sensitive to 10 parts per million, (p.p.m.) equivalent to 0.001 percent, and can be made semiquantitative by using suitable standard samples. INTRODUCTION Although selenium is widely distributed in the United States, the known deposits are either so small or so low grade that they cannot be processed economically for selenium alone-4/ At present, commercial production is a byproduct of the smelting and refining of base-metal ores, particularly copper.5/ About 0.75 pound of selenium is recovered per ton of electrolytic copper, and small amounts are recovered by special treatment of assorted smelter dusts and fume products. Since selenium is a strategic metal in short supply, new sources are being sought by both Government and private interests.

Jan 1, 1957

By L. C. IlsLey, H. H. Clark

In various publications relating to safety in mining the Bureau of Mines has called attention to the hazards attending the use of openBame lamps. An open-flame lamp is a potential source of danger in any coal mine. It may start a fire in a dry mine or an explosion in a gaseous mine. The type of open-flame oil lamp now used in mines is the product of long evolution; its principal merit is simplicity. That such a light is unsafe in an atmosphere containing gas (methane) is evident, and Sir Humphrey Davy immeasurably increased safety in coal mines when he found means of protecting a lamp flame so that it would not readily ignite gas. The safety lamp, however, gives less light than the open-flame lamp, is not as simple in construction, is more cumbersome, and must De carried in the hand .. Consequently, some miners are reluctant to abandon the open-flame lamp for the safety lamp, and risk their own lives and the lives of their fellow workers with the one rather than to be hampered by the other. When small electric bulbs, with their clear, white light, and small electric storage batteries became available, the advantage of combining these elements for a miner's lamp seemed manifest. The combination looked simple and safe, but was soon found to have elements of danger and weakness peculiar to itself. The Bureau of Mines showed, in 1911, that the breaking of a miniature electric bulb in an inflammable mixture of gas and air might ignite the mixture, so that only the fragile glass of the lamp bulb might stand between the miner and injury or death. There Was also a possibility that sparks from the small battery would ignite gas, and the accidental spilling of the contents of a battery on the miner's clothing or skin was a possible source of injury. The first portable electric miner's lamps that were carried in the hand, or with the battery strapped to the back and the light carried on the head, were exceedingly crude and were designed without appreciation of the sources of danger. The possibility, however, of producing a safe and practical miner's lamp by the proper combination and design of the elements available promised to increase safety so greatly that the Bureau of Mines attemr>ted to stimulate better design and construction by careful investigations and the establishment of an approval system that would be an assurance to the miner and an advantage to the maker of the lamp. As a result various manufacturers submitted types of lamps, cords, and bulbs for test and cooperated with the bureau in efforts to so improve the safety features of these devices that the lamps would P&$ specific tests for approval.

Jan 1, 1917

Operator efficiency and control capability along with cost effectiveness have been the quest of mining, industrial, and mobile hydraulic engineers for years. The majority of the functions in present day fluid power systems are controlled by on/off control valves. They are inexpensive and provide easy installation and operation, but they lack the quality of fine control of load flow or what is sometimes known as "feathering the load". An alternate approach to obtaining this capability is the use of electro-hydraulic servo-valves, but their implementation into a system is complex, and they are expensive. As a result, electrohydraulic systems are still used primarily in the aerospace industry. Of late, a compromise seems to have evolved between the on/ off control systems and the servo-technology is the so-called proportional flow control valves. A proportional flow control valve meters fluid to the load in proportion to the input command from the operator. In principle, it is similar to a conventional flow control valve and is tailored to meet the control requirements from the load point of view. The hydraulic system using this valve usually works in an open-loop mode with the operator closing the loop. Incorporating load-sensing mechanisms and adoption of electrical/electronic signalling into the valve make it the "ideal valve" which designers have been looking for from a techno-economic point of view.

Jan 1, 1983

By D. E. Redmon

Exploration of hidden mineral deposits becomes increasingly important as known ore reserves are depleted. The primary objective in any exploratory program is to obtain enough reliable information to evaluate accurately the potential of the mineral deposit. Constant improvement in equipment and technique has established drilling as one of the most valuable methods of exploration. This paper presents the results of studies of several drilling methods currently used in the search for uranium deposits in sedimentary formations from surface drill sites. Also presented is a description of drilling with wire-line equipment from an underground location in metamorphic rocks. The studies were conducted in the Colorado Plateau area and in northwestern New Mexico and Wyoming. Statements of a general nature pertain to conditions or situations existent in those areas.

Jan 1, 1960

By C. H. Larsen

The results of a comprehensive investigation of conveyance arrestment devices (safety catches) in United States coal mines are presented. Availability and use, performance, inspection, maintenance, testing, procedures, and regulatory requirements were investigated. Information was obtained from equipment manufacturers, mine operators, and regulatory-agency personnel, as well as from studies of domestic and foreign mining safety regulations. Traditional mine hoists and commercial elevators for mine use were investigated. Results of this and an earlier study of wire-rope practice in United States coal mines show a continued need for conveyance arrestment devices. A wide variety of these devices are in use. Only two types have been proved reliable for stopping a conveyance without injuring passengers or equipment. These are elevator overspeed-actuated wedge-clamp (Type B) safeties and broken-rope-actuated devices for wooden guides using a single-tooth-dog design developed in Ontario as a braking element. Elevators are widely used in U. S. coal mines. When maintained according to American National Standards Institute (ANSI) Specifications A17. I and A17. 2, they appear to present no major arrestment problems. Of 42 coal-mine hoists used for man transport that were inspected, 30 are in vertical and 12 in inclined shafts. Twenty-four vertical shafts use wood guides; 6 use steel. The 12 inclined-shaft systems use flanged-wheel T-rail guidance. Two wood-guided vertical-shaft systems use the single-tooth Ontario-type dog; the other 22 use multi-toothed wedges, cams, or dogs that have been proved highly unreliable. The arrestment devices in the six steel-guided vertical-shaft systems and in six of the inclined-shaft systems cannot be evaluated because performance data are lacking. The remaining six inclined-shaft systems have no arrestment devices at all. Of the 36 hoists with arrestment devices, the devices of 16 are never tested, the devices of 10 are actuated periodically with the conveyance at rest, and the devices of the other 10 are actuated periodically with a slow-moving conveyance. Although high speed is as probable as low speed in an emergency and would provide the best test of arrestment capability, no tests are performed in the United States which demonstrate the ability of an arrestment device to stop a loaded conveyance from high speed. Mine operators indicate little confidence in their conveyance arrestment devices, and manufacturers recognize a need to improve their products. Neither state nor Federal regulations provide a guide to this improvement. Mine operators, manufacturers, and state and Federal regulatory agency personnel would welcome specific guidance. In view of this, a set of application, design, actuation, stopping-performance, and testing and inspection criteria is presented as a guide to eliminating the inadequacies of these devices. Recommendations are included for improving hoist controls and machinery directly affecting conveyance safety.

Jan 1, 1972

By P. M. Daling

This report, sponsored by the U.S. Bureau of Mines, presents the results of an examination of available safety assessment methods and their applicability to the mining industry. Standard safety analysis procedures were evaluated for relevance to the mining industry and mine operators' needs. The major safety concerns and needs of mine operators were identified through telephone contacts and a visit to a mine site. Safety assessment methods recommended for use by the mining Industry were also Investigated for potential adaptability to a user-interactive computer system. Several methods were determined to be immediately transferrable to the mining industry; these techniques are described in a user's handbook produced as part of this project. The handbook gives detailed instructions on appropriate application and utilization of these methods. Other techniques will require further development before they can be effectively transferred to the mining industry. These methods, their advantages, disadvantages and resource requirements are described in the final project report. Recommended system safety analysis techniques facilitate an evaluation of total mine system safety and a determination of safety-related interactions among systems within a mine. The application of these methods to the mining industry could result in reductions in both the frequency and the consequences of mine accidents.

Jan 1, 1983

By Christopher C. Jobes

This U.S. Bureau of Mines report describes a system to determine the position and heading of a mining machine during maneuvers in the face area of an operating mine section. The system is the first step in the development of a guidance system for automated mining machines. The position and heading algorithm is described, and a preliminary error analysis is performed. The sensors employed were linear position transducers mounted on a mining machine with their cables attached to points on a stationary reference. Four linear position transducers were used to provide a data redundancy that increased the reliability of the guidance system. The linear position information obtained from the transducers was processed mathematically via the position and heading algorithm to provide the desired position and heading information. The algorithm takes advantage of sensor redundancy to continually test the accuracy of the sensor data. The major sources of error were determined to be the linear position transducers, the analog-to-digital (A/D) converter used to interpret the data, and the sampling frequency of the measurement system. These sources of error were evaluated to determine their inaccuracies for use in calculating the overall system accuracy.

Jan 1, 1990

A major hazard to workers in underground mines is fire and the resulting contaminated air. Fire reaches miners thousands of yards away with carbon monoxide gas and other toxic fumes. The same ventilation system that furnishes fresh air to miners can also be the vehicle to carry contaminated air to remote locations. To reduce these problems, the U.S. Department of the Interior's Bureau of Mines entered into Contract H0242016, "Mine Shaft Fire and Smoke Protection System," with FMC Corporation, Santa Clara, California, to evaluate mine shaft fire and smoke hazards and to develop and demonstrate a low-cost, reliable mine shaft fire and smoke protection system that would be applicable to a majority of metal and nonmetal mine shafts, including raises and winzes, especially in deep mines.

Jan 1, 2011

By C. A. Geffen-Fowler

This report, sponsored by the Bureau of Mines, presents the results of an examination of the safety of the Blind Shaft Borer (BSB) shaft sinking system and an alternative modified BSB design concept in comparison to conventional shaft sinking technology. Detailed study of the two systems was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the BSB systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates both the frequency and the potential consequence of accidents. A safety evaluation of the component operations of the two BSB systems was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that both BSB systems are safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by over 30%, on the average, with the use of the original BSB system, and by an average of about 10% with the modified BSB. Design change recommendations to further improve the safety of these systems include better fire suppression systems, improved man haulage systems and more compact hydraulics. An operational safety manual was also developed for the modified BSB system.

Jan 1, 1981

By John E. Lambert

Automatic control of drum head continuous mining machines was investigated as a means of reducing respirable dust generated and operator variabitity. Literature survey, manufacturer interviews and mine visits were the major information sources. Technically feasible automation concepts were Identified to control sump and shear rates, cutter head elevation limits and sumping distance. These are the elements of a programmed cutting cycle which maintains peak penetrating force on the cutter, to maximize depth of cut and therefore reduce dust generation. Based on the industry surveys, successful underground hardware demonstrations must be completed in order to stimulate the market demand for these advanced control features.

Jan 1, 1979

By A. B. Hooker, L. C. IlsLey

Explosives have been fired electrically for several decades. Mountains have been tunneled, deep shafts sunk, extensive coal and metal mine workings excavated and, in times of war, railroads, buildings, bridges, and fortifications have been destroyed by means of electrically fired explosives. Modern engineering depends so much on explosives that their safe and efficient handling and especially their detonation are of prime importance to all those connected with the use of explosive agents. Electric shot-firing is only one method of igniting explosives, but it is rapidly spreading and because of certain inherent safety features should be encouraged. Data collected by the Bureau of Mines indicate that in the United States a large percentage of the blasting in quarries, shafts,· and tunnels, and from 15 to 25 per cent of the blasts in mining operations, are set off electrically. The Bureau of Mines is interested in electric shot-firing because of its use in mining, and especially because electric methods, when properly applied, are undoubtedly safer than other methods commonly used. Electrical problems of many kinds must be solved in dealing with the various phases of electric shot-firing. Success in using an electric detonator is closely linked with the resistance of its bridge, the resistance of its leg wires, and the insulation of its current-carrying parts. The proper layout of a circuit where a number of shots are to be fired simultaneously depends not only on the types of detonators that are used and their arrangement and interconnections, but also on the size and insulation of the wire leading back to the source of power, and even on the source of power itself. Various types of electric shot-firing machines have been developed, and these offer still another field for study. In investigations of electric detonators and electric blasting equipment, the oscillograph is valuable because it can record electrical activity over very short intervals of time. By its use more complete information about electrical performance can be obtained than by any other means.

Jan 1, 1926

By Richard S. Fowkes

This Bureau of Mines report describes the Human Factors in Mining Search System (HFMSS), a computerized information retrieval system that provides relevant human factors information from journal articles, research reports, seminars, conferences, etc. in terms of 19 mining-related categories. It is the only existing data base that stresses all of the areas of human factors as applied to mining. Examples of these categories are biomechanics and work physiology, human error and human reliability, work design and task analysis, manual materials handling and back injuries, hand tools, organizational and management practices, psychological factors, and training. Although the emphasis is on literature dealing directly with mining, applicable material from other areas of research is included for those categories in which little research has been done in mining. Each record in HFMSS can be recalled by any field such as title, author, date, source, descriptive terms or key words, as well as by any words found in an abstract that describes the purpose, procedure, and results of the research. This report describes HFMSS fields and subject categories, the annotated bibliography, user's manual, and thesaurus of key words. Example printouts in both brief and full formats are included as an appendix.

Jan 1, 1990

By P. M. Daling, C. A. Geffen

The objectives of this study were to examine a representative cross section of formal safety analysis techniques developed for the nuclear and aerospace industries, to recommend those methods that would be suitable for application to the mining industry, and to include those methods in a user's manual. Volume XI of this report, the user's manual, describes several methods that were determined to be immediately transferrable to the mining industry. The handbook gives detailed instructions on appropriate application and utilization of the methods. Other techniques will require further development before they can be effectively transferred to the mining industry.

Jan 1, 1983

By John P. Wagner

The details of a three-phase study (total time period of 12 months) entitled ?Fire Alert Systems for Metal and Non-Metal Mines,? are presented. Phase 1 consists of a state of the art survey on fire detection devices and gas sensing techniques. Phases 2 and 3 include laboratory screening and systems concepts testing on various detectors classified as products of combustion, optical view-field and contact (or thermal) types under incipient and flaming combustion conditions. Recommendations for a mine fire detection system to protect shaft, sealed off or mined out (from spontaneous combustion of sulfide containing ores and cellulosic materials), and fuel storage areas are also included. me principal problem area noted during Phase 1 study is the high expected occurrence of false alarming of products of combustion detectors (POC") subjected to normal mining operations---diesel vehicles and equipment and shot firing or blasting operations. Simultaneous gas sensing of either the ratio of CO/NOx or CO2/NOx with detection of one or more fire signatures (smoke, radiant energy, or heat sensing) is the recommended approach to discriminate against these operations.

Jan 1, 1975

By P. M. Daling

The objectives of this study were to examine a representative cross section of formal safety analysis techniques developed for the nuclear and aerospace industries, to recommend those methods that would be suitable for application to the mining industry, and to include those methods in a user's manual. Volume II of this report, the user's manual, describes several methods that were determined to be immediately transferrable to the mining industry. The handbook gives detailed instructions on appropriate application and utilization of the methods. Other techniques will require further development before they can be effectively transferred to the mining industry.

Jan 1, 2006