Search Documents

By Eleanor Abshire

This bibliography is the result of a cooperative project undertaken by the Bureau of Ships and the Bureau of Mines to accumulate literature published to date on zirconium and hafnium and to establish an information center on these metals for the use of any interested research organization or library. This bibliography, which will be supplemented as additional information is accumulated, consists of references, with abstracts, to pertinent literature on the subject published from 1907 to date.

Jan 1, 1957

By Katherine Harding

This Bureau of Mines publication describes a practical approach to sampling that does not require elaborate statistical techniques. Simple steps are given for finding a cutoff point in the response from a repetitive survey. This procedure can be used to estimate the aggregate value of the characteristic being measured without waiting for a complete count from the survey. This is a useful technique when the reference periods are repeated at frequent intervals, such as monthly and quarterly, and when the statistical collecting agency is engaged in publishing timely data which must be accurate economic indicators.

Jan 1, 1971

By K. L. Williams

The Bureau of Mines laboratory tested the response of a commercially available real-time aerosol monitor (GCA RAM-1) to various dusts. Monitor measurements were recorded, averaged, and compared with simultaneous gravimtric measurements of each test dust. Tests usually lasted several hours. The test dusts of various particle size distributions used included coal, limestone, and a commercially available test dust. For each particular dust, the monitor response was linear and correlated well with mass concentration over the range of about 0.5 to 10 mg/m3. The monitor can estimate a 2.0-/m3 respirable coal dust concentration within as little as 26 pct with 95 pct confidence. The monitor must, however, be calibrated with the dust to be measured because the instrument response is affected by the type of dust particle. The average monitor response to same mass concentration of coal dust was approximately twice the average monitor response to the same mass concentration of limestone dust.

Jan 1, 1984

By R. V. Ramani

"In Part 1 of this paper, published in the August 1995 issue of Natural Resources Forum, a review of several mining disasters around the world established the complex nature of their causation and their catastrophic effects. The involvement of human beings, either through acts of commission or omission, was highlighted. In Part 2, a discussion of the various approaches to disaster control, mostly as practised in the USA, is presented. A systems approach to disaster prevention incorporating elements of hazard identification, mine design, emergency response and post-emergency audit is presented.In the USA the role of government in the affairs of its citizens is continually growing. This role is intended to ensure an unimpeded pursuit of happiness and prosperity by the population and to curtail actions which are restrictive or harmful to the citizenry. The passage of a legislation is an indication that it has been decided through the established process that the activities covered by the legislation should receive appropriate consideration. The enactment of the Coal Mine Health and Safety Act of 1969 (The 1969 Coal Act), the Mine Safety and Health Amendment Act of 1977 (The 1977 Mine Act) and the Surface Mining Control and Reclamation Act of 1977 (The 1977 Surface Mining Act), was specifically intended to further the role of government in the health, safety and environmental affairs of the mineral industry.Currently, the federal government's responsibilities for mine safety and health are divided among three agencies: the Mine Safety and Health Administration (MSHA) in the US Department of Labor, the Bureau of Mines (USBM) in the US Department of the Interior and the National Institute for Occupational Safety and Health (NIOSH) in the Department of Health and Human Services (National Research Council, 1981). MSHA is responsible for issuing and enforcing mine safety and health regulations, for training miners and for responding to mine emergencies. The Bureau of Mines is responsible for conducting research on mine safety and on the technological means for reducing health and safety hazards in mines. NIOSH conducts research relating to miner health, and together with MSHA, tests and certifies devices used to detect hazardous materials in mines and protective equipment used by miners. NIOSH also plays a public health role in that its activities in mining include health hazard evalua¬tions, general mining surveillance as mandated by law and medical surveillance including coal miner X-ray and autopsy programmes. MSHA shares with the Bureau of Mines the responsibility for integrating R&D results into operational practice. MSHA implements R&D results either by incorporating them into its own operations or by rule making that requires new practices or equipment to be adopted by the mining industry. In many instances, the Bureau's R&D results have been adopted by the mining industry without rule making."

Dec 1, 1996

By David L. Veith

This report summarizes a Bureau of Mines review of selected literature on the effects of subsidence due to high-extraction underground coal mining on farmland areas. The data are presented for consideration in evaluating the subsidence effects due to similar mining techniques on the prime farmland areas of Illinois. In Illinois the ground water level in the glacial drift is only 2 to 15 ft below the nearly flat to gently rolling ground surface. The main subsidence concern is flooding, as caused by the lowering of the ground surface, and the subsequent effects on crop production. Positive drainage must be maintained in the farmlands, and the need exists for extensive regional planning by the mining and agricultural industries to maximize short- and long-term production from both efforts. The Bureau is cooperating with the State of Illinois to develop basic information necessary for such planning.

Jan 1, 1987

By R. Vernon Helm

Four tables listing values for the various physical properties of those sulfur compounds most likely to occur in petroleum and petroleum products are given herein. The data necessary to bring the first compilation2/ in this subject up to date are given in table I -Revised and Additional Data, which includes boiling points, refractive indices, densities, and freezing points. Tables 11-, III, and IV are published for the first time and include refractive indices for the F, C, and G' lines of hydrogen and the helium D:3 line; surface tensions and viscosities, and refractivity intercepts, specific dispersions, specific refractions, and parachors. The need for information concerning the sulfur compounds in petroleum is becoming-more urgent because of the necessity of refining larger quantities of high-sulfur crude oil to meet the rising demand for petroleum products. For a number of years the Bureau of Mines has been engaged in research to make available more information concerning the properties of the sulfur compounds in petroleum. The petroleum industry has recognized the value of such studies, and as a result the American Petroleum Institute has established Research Project 48A to study sulfur compounds. The investigations under this Project are to be done in Bureau of Mines laboratories as a cooperative project in connection with the work already started.

Jan 1, 1949

By C. M. Frost

Two Federal Bureau of Mines recycle hydrogenation experiments to prepare catalytic cracking feed stock were made at 3,000 pounds pressure with crude shale oil retorted from Green River (Colo.) shale in the gas-combustion retort. The hydrogenated product from the first experiment, made at 784° F., was used for investigating the effects of nitrogen content on catalytic cracking yields and for determining the quality of the catalytically cracked gasoline. Hydrogenated product containing 0.14 percent or more of nitrogen produced less gasoline when cracked in a CAT "A" unit than was obtained from East Texas light gas oil cracked at the same conditions; product containing 0.10 percent or less nitrogen produced a quantity of cracked gasoline equal to that obtained from the East Texas light gas oil. The catalytically cracked gasoline had research octane numbers calculated to be approximately 95 clear and 103 with 3 ml. of tetraethyl lead. The principal product from the second experiment, made at 828° F., was a low nitrogen content gas oil which was used for investigating the yields of cracked products obtained when it was catalytically cracked to different degrees of conversion. Yields of cracked products, when plotted as functions of conversion, were essentially the same, within the experimental range of the data, as published yields from catalytic cracking of East Texas heavy gas oil; however, yields from cracking the shale-oil product did not display the sensitivity to change of cracking temperature that has been found for East Texas gas oil.

Jan 1, 1960

By Larman J. Heath

Liquid incendiaries were burned within the interstices of several different types of sandstone cores to determine the technical feasibility of increasing sandstone permeability by this method. Fuel-oxidant mixtures were tested in 186 cores; six cores exploded when ignited. In virtually all instances, the explosion completely pulverized the sandstone cores. In addition n those cores damaged by explosions, 24 cores were fractured so severely that permeability tests were impossible. Although combustion gener¬ally increased the permeability, specific mixtures at given pressures were inconsistent in their ignition and burning behavior. Tests indicated that the heat of burning incendiaries significantly increased sandstone permeability. The improved permeability ratios were usually less than 2, but one was 10.3. Permeability alteration by other in situ methods was not as effective as that by flame propagation.

Jan 1, 1971

By G. R. Peterson

The Bureau of Mines evaluated the potential supply of cobalt from known domestic resources, both as a primary product from some deposits and as a byproduct from others, and found that U.S. production could play an important role in meeting U.S. cobalt needs by the mid-1980's. This production would be of a relatively short duration, however, with production declining significantly before the year 2000. As part of the study, a tonnage-price relationship was developed indicating the quantity of cobalt that could be produced from known cobalt-bearing deposits at various primary commodity prices and at a 15-percent rate of return on the required capital investment. All capital and operating costs are calculated in August 1980 dollars, and commodity prices are based on August 1980 prices. Known U.S. cobalt-bearing deposits which represent the current U.S. cobalt reserve base contain some 310,800 metric tons of cobalt in slightly over 1 billion metric tons of demonstrated mineralized material. Approximately 37 percent of the cobalt contained in the reserve base is considered recoverable using existing technology. Of this quantity, some 87,000 metric tons of cobalt is economically recoverable assuming a cobalt price of $25 per pound, a copper price of $1 per pound, and a lead price of $0.40 per pound. Assuming that the cobalt price decreases to $15 per pound, keeping copper and lead prices constant, the quantity that is considered economically recoverable declines to some 45,700 metric tons. Domestic cobalt consumption in 1979 was 7,900 metric tons (17.4 million pounds). Currently, no primary cobalt is produced from domestic resources, and none has been produced since 1971.

Jan 1, 1981

By Willard L. Hunter

The smelting of tin slags was undertaken at the Bureau of Mines Albany Metallurgy Research Center (AMRC) to produce crude columbium-tantalum ferro-alloy as a unit operation in the production of pure columbium and tantalum oxides or chlorides. Columbium and tantalum-rich alloy was prepared during short unrelated campaigns over a total period of 12 years. Tin slags from Malaya and the Congo (Geomines) were smelted. These slags were reduced by carbon in a small, single-phase, steel-making furnace} a larger three-phase, steelmaking furnace, and a three-phase, submerged-arc furnace, In all cases depleted slags were fluid and easily tapped from the furnace. However, unless diluted by iron additions, the metal product was a viscous, high-melting, heterogeneous mixture that could be removed from the furnace only by hand rabbling.

Jan 1, 1966

By James A. Wasson

The Mitchell and Berea sands were cored and logged in Fred Link well K-l, Lower Newport field, Washington County, Ohio. Core and reservoir fluid analyses and available field data were studied to determine if these sands could be successfully waterflooded. The results of the study indicate that there is insufficient oil in place to form an oilbank in either the western Mitchell pool or the Berea sand, and that no commercial recovery of oil by waterflooding can be obtained in these reservoirs.

Jan 1, 1967

By Ben E. Lindsly

The study of "bottom-hole samples follows in natural sequence the study of samples obtained under high pressures at the well heads of flowing wells. The principal object of this phase of gas-solubility research, started actively in January, 1930, was to gain a more accurate knowledge of the physical and chemical characteristics of the oil-gas mixtures that exist in natural reservoirs.. In possession of actual data regarding the condition of the oil; the quantity of gas liberated from solution upon dimunition of pressure; and the relative volumetric proportions of gas to oil at various pressures throughout the flow string in a well, it should be possible to predict, with a fair degree of accuracy, That physical changes these mixtures would undergo throughout the life of a pool. Such information not only is important in designing flow strings in flowing Tells but is important also in solving problems relating to pumping efficiency and the power required for pumping. Although certain fundamental data were obtained in the study of samples taken at the well head, "bottom-hole" samples are more representative of subsurface mixtures of oil and gas because they are obtained at reservoir temperatures, and before the oil has had the opportunity of intermingling with extraneous gas; that is, gas which either was not in solution originally, or which was liberated from solution at higher pressure, and later became mixed with the original undissolved gas.

Jan 1, 1933

By Walter Kawa

Coals of various rank were reacted by the Bureau of Nines in plasma jets generated from argon and argon-hydrogen mixtures containing up to 33 volume-percent hydrogen. Average plasma temperatures ranged from about 3,400° to 12,000° C. Products were a solid residue and a gas containing hydrogen, methane, acetylene, diacetylene, and oxides of carbon. The highest yield of acetylene obtained with argon plasmas was 15 percent by weight of moisture- and ash-free coal. The data indicated that acetylene yields of 40 percent or higher can be obtained from the reaction of coal in argon-hydrogen plasmas, although results from these experiments could not be correlated with operating variables because of low recoveries plasma contained sufficient energy to heat the coal to temperatures as high 9,000 or 10,000° C, but complete devolatilization did not occur in any experiment.

Jan 1, 1966

By L. F. Willmott

The production operation of a Kerpely gas producer at Louisiana, Mo., is described. This unit, originally designed for airblown operation was modified to permit using oxygen in the blast in place of air. The first runs J for test purposes, were made in June 1950. After this, seven production runs were made and these are the subject of this report. Total gasification time was 245 days. In each run, Nut or Pea coke or mixtures of both at a rate varying from 1,700 to 2,300 pounds per hour was converted with oxygen and saturated steam to produce synthesis gas - primarily carbon monoxide and hydrogen -approximating a predetermined rate of 80,000 to 95,000 cu. ft. per hour and a predetermined hydrogen-carbon monoxide ratio, The requirements per 1,000 std. cu. ft. of (CO + H2) were 21.6 to 30 pounds of coke, 213 to 267 std. cu. ft. of oxygen, and 3L4 to 47.B pounds of steam.

Jan 1, 1955

By J. R. Cobble

Dissolution of chalcopyrite with acidified ferric sulfate produces a sulfur layer on the unreacted chalcopyrite surface that interferes with further dissolution. The U.S. Bureau of Mines has developed a process to improve the leaching kinetics of these types of diffusion-controlled systems. The system features the Bureau-developed turbomill, an attrition grinder that scrubs the reaction product coating away from the unreacted mineral grains during leaching. The system can be operated continuously at any temperature up to the boiling point of the leaching agent. This method is a hydrometallurgical alternative to chalcopyrite smelter technology and eliminates sulfur dioxide emission problems with its associated costs. Batch testing at 900 C with the chalcopyrite-ferric sulfate system resulted in copper extraction exceeding 99 pct. At an optimal energy consumption of 1,520 kW· hjst, 95 pct of the copper was extracted. The pregnant liquor was clarified and tested for typical solvent-extraction recovery of the copper. Two-stage extraction and two-stage stripping recovered 96 pct of the copper in an electrolyte suitable for copper electrowinning.

Jan 1, 1993

By J. J. McClelland

The face area of a continuous mining section of an underground coal mine is the most dangerous area in the mine. Workers there are at nearly twice the risk of death or disabling injury than those in other parts of the mine. Despite extensive training of miners and improved equipment and mining methods, fatality and injury rates have remained constant during the past few years. It is clear that advanced research is necessary to apply new technologies or modify work procedures to solve the continuing problem of the loss of lives and the numerous injuries at the mine face. A U.S. Bureau of Mines research program is developing a Reduced-Exposure Mining System (REMS) that relocates personnel operating the mining machinery at the face away from the hazards to a nearby haven of relative safety. REMS uses proven technologies of computer automation and robotics to help control the operation of the mining machines at the face, while personnel are moved away to a nearby, safe control room. In this protected, well-ventilated environment, they can supervise or control the operation of the machines while viewing what the machine is doing using video and graphic display monitors.

Jan 1, 1994

By J. Drew Potts

In this U.S. Bureau of Mines study, four underground respirable dust surveys were conducted to determine factors affecting belt entry dust levels and how using belt air to ventilate work areas affected dust exposures. Belt entry dust levels on the surveyed longwall and continuous miner sections averaged 0.59 and 0.26 mg/m3, respectively. The stageloader-crusher contributed an additional 0.5 to 0.9 mg/m3 of dust to belt air, while the feeder-breaker contributed 0 to 0.2 mg/m3 of dust. A 1,000-ft increase in belt entry length or a 200-to 500-st-per-shift increase in production resulted in roughly a 0.1-mg/m3 increase in dust. Using the belt entry as an intake entry on the continuous miner section appeared to reduce dust levels by 0.1 to 0.3 mg/m3 during cutting. Belt air was not used to ventilate the face on the longwall section.

Jan 1, 2010

By G. R. Fitterer

In the manufacture of steel by any process the refining period involves the partial elimination of the metalloids carbon, manganese, phosphorus, and silicon, by virtue of their reactions with ferrous oxide. At the end of this refining stage the metal consists chiefly of iron in which small amounts of these materials are dissolved. Unless some deoxidizer is added to the steel at this time, the reaction between carbon and ferrous oxide will continue with such force that it is impossible to form sound steel in the ingot molds. Instead, the product will exhibit a marked porosity due to the formation and trapping of carbon monoxide-the product of the reaction mentioned. However, if deoxidizers are added, steel may be obtained which is dense and free from gas bubbles. At the same time the deoxidation products will remain in the steel as impurities. For example, silicon additions form SiO2 or combinations of SiO2 and FeO. Additions of manganese form deoxidation products consisting of various proportions of MnO and FeO. It is also quite obvious that simultaneous additions of manganese and silicon will form oxide combinations either in the binary system MnO-SiO2 or in the ternary system FeO-MnO-SiO2. Work at the Pittsburgh Experiment Station of the United States Bureau of Mines, in cooperation with the Carnegie Institute of Technology and the Metallurgical Advisory Board, involved the study of such deoxidizing reactions and their products. In this connection considerable information is necessary concerning FeO, MnO, SiO2, and Al2O3, and their various combinations. Some of the most needed data are the melting points of all of these materials. At the outset of this work ordinary methods of melting point determinations were found to be inadequate for various reasons, and the procedure finally selected involved the use of the micropyrometer with occasional corroboration by quenching methods. The reasons for this selection, together with a description of the apparatus, are given in the following pages.

Jan 1, 1932

By Maureen M. Foss

Underground coal mining is hazardous due to changing geological conditions. One geophysical method showing promise for in-seam hazard detection is ground-penetrating radar (GPR). The Bureau of Mines recently completed preliminary studies to demonstrate the feasibility of using GPR for in-seam hazard detection. Investigations included air and coal tests for the purpose of checking equipment accuracy, coal penetration, and other factors such as the effects of receiver orientation. Further investigations involved using both a short pulse and a new prototype synthetic-pulse system to locate a clay vein in a coal seam using trans-illumination. Data were gathered on multiple travel paths, and a back projection processing technique was then used to create a tomographic image using the calculated velocities. A computer model of the same coal seam was subsequently processed using the same tomographic tech-nique, and the results were compared with those of the actual data. Analysis of the tomographic images shows the presence of the clay vein, although its boundaries are unclear due to the tomography method used. Results of these preliminary studies show that GPR is feasible for use in in-seam hazard detection and point the direction that future research should take. A need has been shown for research involving more sophisticated tomography techniques, transmission studies on thicker coal seams, and reflection studies using the synthetic-pulse system.

Jan 1, 1987

By John Dixon

This paper is one of a series on milling methods and costs being published by the Bureau of Mines. Acknowledgment is made to J. B. Tyrrell, managing director, and Wm. Sixt, manager of the Kirkland Lake Gold Mines, for permission to publish this article. The Kirkland Lake Geld Mining Co.'s mill is located on Government Road at the west end of the productive part of the Kirkland Lake mining area, 1 mile west of the village of Kirkland Lake. The crushing plant is connected to the shaft house of No. 2 shaft, which is now the only operating shaft.

Jan 1, 1931