Search Documents

By Ronald S. Conti

A new U.S. Bureau of Mines 6.8-L ignitability furnace was used to study the thermal autoignitability of dust clouds. This furnace has a quartz window to allow observation of the early stages of the ignition process and to allow measurement of the dust explosion temperature. Thermal ignitability data were obtained for various carbonaceous and metal dust clouds, with particular emphasis on various ranks of coal dusts. One of the reasons for the construction of the new 6.8-L furnace was to evaluate the effect of chamber volume on the measured autoignition temperatures. Therefore, data from the 6.8-L furnace were compared with data measured earlier in a 1.2-L furnace. The conclusion is that the autoignition temperatures measured in the 6.8-L furnace were only slightly lower on average than those from the 1.2-L furnace. These data on the minimum autoignition temperatures of various materials will be useful in analyzing the thermal ignition hazards of dust clouds in the mining industry and other industries that manufacture, process, or use combustible dusts.

Jan 1, 2010

Safety rules for installing and using electrical equipment in and about coal mines covered in this information circular supersede those previously included in Bureau of Mines Bulletin 514, issued in 1952. This revision brings these rules up to data and more nearly in line with present operating and safety practices in the industry. The, rules are intended to supplement existing existing Federal and State regulations, and no provision shall be construed to oppose or supersede any provisions of the Federal Mine Safety Codes, the Federal Coal Mine Safety Act, or the mining laws of any State. The rules were designed to permit progress, such as application of new or improved materials and equipment or use of new practices where these materials, equipment or practices retain or improve the level of safety established by these requirements. It is hoped that they will fill the need for a concise edition for mine electricians and electrical engineers, especially those who do not have ready access to more detailed rules or codes.

Jan 1, 1964

Safety rules for installing and using electrical equipment in and about coal mines covered in this information circular supersede those previously included in Bureau of Mines Bulletin 514, issued in 1952. This revision brings these rules up to date and more nearly in line with present operating and safety practices in the industry. The rules are intended to supplement existing Federal and State regulations, and no provision shall be construed to oppose or supersede any provisions of the Federal Mine Safety Codes, the Federal Coal Mine Safety Act, or the mining laws of any State. The rules were designed to permit progress, such as application of new or improved materials and equipment or use of new practices where these materials, equipment, or practices retain or improve the level of safety established by these requirements. It is hoped that they will fill the need for a concise edition for mine electricians and electrical engineers, especially those who do not have ready access to more detailed rules or codes.

Jan 1, 1964

By W. M. Nabors

As part of a program to promote conservation and efficient utilization of petroleum resources, Bureau of Mines engineers at the Morgantown (W. Va.) Petroleum Research Laboratory are studying secondary oil-recovery projects in the Appalachian region. The increasing demand for petroleum and its products and the increasing cost of exploratory drilling tend to emphasize the importance of improving the recovery of oil from known petroleum reserves. Published reports setting forth the pertinent facts of these operations may help others to profit by the experience. This report presents the results of a study of secondary-recovery methods used in West Virginia by the Piedmont Oil and Gas Co., the Ryan Oil Co., and Water floods , Inc., on their Roane County leases in the Walton and Clover Rush Run pools. The principal oil-producing horizon underlying the area studied is the Big Injun sand, at approximately 2,000 feet. The sand is often referred to as blanket sand because it underlies much of the State and is oil-productive in many localities. Most of the pools in the area were discovered during 1907 to 1910 and were similarly developed and operated.

Jan 1, 1960

By George S. Rice

This bulletin traces the growth in the belief in the explosibility of coal dust, summarizes the experiments and mine investigations that have established this belief, and gives the present status of pre- ventive measures. It has been prepared in accordance with the pro- visions of the acts of Congress authorizing investigations relating to the causes of mine explosions, and contains references to and descrip- tions of experiments made at the Federal testing station at Pittsburg, Pa. This station was inaugurated under the United States Geo- logical Survey, and was transferred to the Bureau of Mines on the establishment of the latter on July 1, 1910. Only within comparatively few years has the dry dust of bitumi- nous and lignitic coals been generally recognized as an explosive agent more insidious, threatening, and deadly to the miner than fire damp. Fire damp carries its own flag of warning-the "cap" in the safety lamp-but coal dust, though visible, does not attract attention until present in large quantities. Fire damp is of local occurrence, and except in notable and very exceptional cases is controllable by careful manipulation of ventilating currents. If by mischance a body of fire damp is ignited in a mine, the force of the explosion may be terrific, but the effect is local unless dry coal dust is present, or unless (as it very rarely happens) an explosible mixture of methane gas and air extends through large areas of the mine. In a dry mine dust accu- mulates everywhere, and the blast from the ignition and combustion of bituminous dust may traverse miles of rooms and entries and wreck structures at the entrance to the mine. The comparative potential destructiveness of gas and of bituminous dust is strikingly shown by the history of the Pennsylvania anthracite mines. These mines not infrequently have large inflows of gas, and the resulting mixtures of gas and air have sometimes been ignited, yet no such wide-sweeping explosions have taken place, despite the presence of dry anthracite dust, as have happened in excellently ventilated bituminous mines.

Jan 1, 1911

By A. D. Hahn

This report describes and gives the results of an examination by the Federal Bureau of Mines of ilmenite-bearing placer sand deposits in the 24-mile long valley of Otter Creek, Kiowa and Tillman Counties, Okla. Drilling and sampling was completed in three periods between October 1956 and September 1957. Mineralogic studies and mineral-dressing tests on recovery of ilmenite and other heavy minerals from composited samples of the sands were made in Bureau of Mines laboratories at Rolla, Mo., in 1957 and early 1958. Otter Creek rises in and drains the southwestern extremity of the Wichita Mountains, which are represented locally by knolls and ridges of gabbro and granite surrounded by plains floored with flat-lying Permian red beds. The valley fill consists of a basal sand-clay component, derived from weathering of the igneous rocks, and an overlying silt-clay alluvium. Ilmenite is present in significant quantity and recoverable grain size only in the basal sand-clay.

Jan 1, 1960

By G. L. Oldright

The studies previously made on Smelting in the Lead Blast Furnace have dealt with the custom smelter of the International Smelting Co. at Tooele, Utah, and on the smelter of the Bunker Hill & Sullivan Mining & Smelting Co. at Kellogg, Idaho. The International plant may be considered representative of the traditional custom smelter. The lead smelter of the future seemingly will have to treat increasingly richer lead charges. This feature was then stressed in describing the Bunker Hill plant.

Jan 1, 1934

By Harry W. Campbell

A mineral survey by Bureau of Mines personnel identified no mineral resources or mineral occurrences with development potential at prospects in the Mecca Hills Wilderness Study Area (WSA). Bentonite occurrences are in Skeleton Canyon and Surprise Canyon. Sand and gravel occurrences are numerous in and near the WSA. Much of the Mecca Hills WSA was leased for oil and gas exploration in 1983. No current mining claims or other leases were found in the study area. The Skeleton Canyon Clay Mine yielded clay to seal irrigation canals, Clay to seal ponds was also mined from the Red Top Clay Mine west of the USA. A sand and gravel pit south of the study area (near Box Canyon Wash) supplied material for local construction projects. A commercial sand and gravel pit was operating in 1983 near the mouth of Thermal Canyon 4 miles west of the WSA.

Jan 1, 1984

By Felix duBreuil

The present sampling procedure for evaluating the rock dusting conditions in a coal mine is time consuming. This study considers means by which this procedure could be simplified. Surveys were conducted in six coal mines in Pennsylvania to determine the in¬combustible content of the deposited dust. Some 2,000 samples were analyzed and statistically evaluated. It is suggested that the mean incombustible content could be obtained with fewer samples and smaller samples without greatly increasing the sampling error.

Jan 1, 1972

By L. G. Marshall

Gypsum mining and processing has been one of the principal industries in Iowa for more than 75 years. For most of that period, Iowa has ranked among the five leading States in the production of crude gypsum and of calcined-gypsum products. The Fort Dodge area accounted for 11 percent of the gypsum products produced in the United States in 1956. Before 1927 the output by the major companies came from underground operations, using a room-and-pillar stoping method. At present, all production comes from quarries. The quarry methods at the various properties are similar. This paper describes the quarrying, methods employed in the district and the type of equipment used by each company. The sections on history and geology are, in part abstracts from State annual reports and an Iowa Geological Survey publication.3/

Jan 1, 1959

By John A. Breslin

This report summarizes the principal activities and significant results of the Bureau of Mines respirable dust research program since passage of the Federal Coal Mine Health and Safety Act of 1969 and the Federal Mine Safety and Health Amendments Act of 1977. This program has investigated new and improved techniques and equipment to reduce or prevent the formation of dust during the cutting cycle; to dilute, suppress, or collect airborne dust generated during mining, handling, and processing; and to improve the measurement of dust levels for evaluation of engineering controls and for enforcement of Federal dust standards. The report is intended for mining industry dust control specialists and other interested parties. It includes a brief summary of the program to date, a section on future research plans and goals, and a list of publications resulting from the Bureau's respirable dust program.

Jan 1, 1982

By D. J. Dollhopf

A week-long selective overburden handling dragline op ration was conducted at a strip mine near Colstrip, Montana. The objective of the demonstration was to hvdrologically isolate a saline overburden zone during placement in the spoil piles. The saline zone had concentrations considered inimical to successful reclamation and was potentially dangerous to future water quality in the spoils aquifer. The zone was identified after review of chemical data for overburden samples collected from the intense 60 m grid drilling pattern. The saline zone in the overburden was: 1) handled in a normal manner; 2) segregated and buried; and 3) segregated, buried, and covered with a relatively impermeable 1.0 m thick clay cap. The method used to formulate this demonstration, the demonstration itself, and the monitoring and evaluation techniques are described in this report. Observation wells were installed to monitor ground water in the overburden, Rosebud coal, and McKay coal. Data from these wells were, used to estimate post reclamation water levels and to evaluate recharge and water movement characteristics in the vicinity of the demonstrations. The inimical zone was successfully handled in a selective manner with a minimum of delays. Economic analysis indicated cost of these selective burial operations to be about 1.1 to 1.5 times the cost of the normal operation at this particular mine site. Long term monitoring will be required to evaluate the effectiveness of these handling techniques in hydrologically isolating undesirable overburden materials.

Jan 1, 1977

By F. M. Boler

The U.S. Bureau of Mines conducts research at the Galena Mine, Wallace, ID, with the aim of mitigating the effects of rock bursting. Destress blasting is commonly used as a stress control technique at the mine. A digital seismic array and an array of borehole pressure cells (BPC's) had been installed near the site of a stope undergoing mining and periodic de stressing. The instrumentation was being monitored at the time of a destress blast of the 46-99 stope. No significant seismic events occurred coincident with the destress. However, the destress was followed by a 2 ½ -week period of increased seismic activity, including two damaging events on February 7, 1990, at 034500 (hour, minute, and second) and 122020 Pacific standard time. BPC measurements indicated coseismic ground pressure changes on the order of 200 to 300 kPa associated with the damaging events. Fault plane solutions and dislocation models established that stress changes induced by the event at 034500 may have been significant in promoting the occurrence of the event at 122020. Theoretical investigations suggest that applying knowledge of the existing stress field, an understanding of rock burst mechanics, and fracture mechanics principles can improve destress effectiveness.

Jan 1, 2010

As part of a continuing program of evaluating the Nation's crude-oil resource, this report presents information pertaining to resource, primary reserve, and potential waterflood reserve for 3,209 selected reservoirs contained in 24 oil-producing States, as of January 1, 1968. To that date the selected reservoirs had not been subjected to pressure-maintenance or secondary-recovery operations. These reservoirs also met the following parameters: (1) a minimum of five oil-producing wells on January 1, 1968, (2) a minimum of 50 acres areal extent, (3) a minimum of 50,000 bbl of oil ultimate primary recovery, and (4) the principal reservoir energy was other than active water encroachment. The selected 3,209 reservoirs produced 527 million bbl of oil in 1967, about 17 pct of U.S, total production. Primary oil reserve was 4,983 million stb; in addition, there was 6,043 million stb of potential water- flood oil reserve. Oil resource in the selected reservoirs was 59,547 million stb. A brief history and outlook of waterflooding are presented for each State. Depth and producing rate statistics and geologic distributions of production, resource, reserve, and potential waterflood reserve for the selected reservoirs are presented by States in the appendix. Also included in the appendix are description, history, and technique modifications of waterflooding, and a preliminary cost estimate of a closed-system water-injection project.

Jan 1, 1970

By M. W. Von Bernewitz

The Bureau of Mines receives frequent requests for information on the treatment of mercury ores, but as its own and almost all other publications on mercury are out of print, the Bureau has prepared this circular on the metal for the prospector and operator of small mines and plants. Mercury, commonly though improperly termed ?quicksilver?, is the only common metal that is liquid at ordinary temperatures. Mercury is used in the amalgamation of gold and silver, in power boilers, explosives, friction-less bearings, laboratory apparatus, lamps, medicine, paint, rectifiers, and for ?silvering.? The last mentioned is being superseded by silvering with silver. The use of mercury boilers may increase when they are thoroughly understood, but amalgamation is -being replaced to some extent by the use of corduroy and other collecting mediums, such as jigs and flotation cells.

Jan 1, 1937

By F. D. Everett

Thermoelectric and metal alloying applications have changed the status of tellurium from oversupply to under supply . In a search for new sources of this element in Arizona , Colorado , New Mexico , Utah , and neighboring states , the Bureau of Mines analyzed more than 200 samples and obtained the results of tellurium determinations by private companies on more than 500 samples from a wide variety of mineral - bearing deposits . The About 40 minerals containing tellurium have been reported , mainly tellu- rides of gold , silver , bismuth , mercury , lead , copper , iron , and nickel . minerals usually occur in small quantities and identification in ores is extremely difficult . Samples containing more than 0.1 percent tellurium were taken from the Hilltop and Memphis properties in Dona Ana County , N. Mex . , and the Silver King property in White Pine County , Nev . , where development was chiefly for base metals . The Lone Pine mine in Catron County , N. Mex . , and the Bambolla mine near Moctezuma , Sonora , Mexico are potential sources of native tellurium occurring in small but high- grade pods . Much of the production of tellurium has come as a byproduct of electro- lytic refining of copper and lead- zinc ores in Arizona , Colorado , New Mexico , and Utah . Base -metal ore deposits will continue to be the most important pri- mary source of tellurium , although the concentration in ores is nearly always less than 10 parts per million . Any significant increase in output of tellu- rium probably will be related to production and improved efficiency in smelt- ing and refining base - metal ores .

Jan 1, 1964

By Anthony M. Opyrchal

This Bureau of Mines study assesses the economic significance of the Florida phosphate industry to selected counties in Florida, the State of Florida, and the Nation: it also includes a brief survey of the industry's international impact. Based on forecasts of Florida phosphate production in 1981, and using constant 1977 dollars. estimates are given for 1981 for regional and national output the value of this output, income, and employment created by the phosphate industry in Florida, Federal, Stale, and county tax revenues generated by the State's phosphate industry are also estimated for 1981. The concentrated impact of the phosphate industry on certain areas of Florida and on the State?s regional industries is examined using economic base analysis complimented by an industrial complex approach. The industry's impact at the Stare and national levels is examined through input- output analysis. In addition, an attempt to forecast for 1990 the effects of constraints on phosphate rock mining as a result of economic conditions and other factors is included as an appendix to the report. Also discussed is the phosphate industry's importance to the U.S. balance of trade: U.S. agricultural production. Including forward linkages; the U.S. sulfur industry; and the phosphate industry's importance to the production of fluorine and uranium by- products from fertilizer manufacturing.

Jan 1, 1981

By Nan C. Jensen

Modern high-temperature metallurgical processes have created a demand for raw material for furnace parts and lining that not only will with-stand high temperatures is but will not react with the substance being melted in the furnace. Spark-plug insulators, laboratory ware, tanks for the glassmaking making industry, and saggers and kiln furniture for the chinaware and pottery trades also must be made of materials hat have high melting points. Among the minerals that can be employed for such refractory uses ore those commonly known as the "sillimanite group' -kyanite, andaluste, sillimanite, and dumortierite - and the allied minerals topaz and pinite. Consideration of the occurrence, properties, qualities, uses, and sources of supply of these commodities and the markets for them constitute the subject of this paper. General Features of Kyanite and Related Minerals Kyanite, andalusite, and sillimanite ire composed of three elements - aluminum, silicon, and oxygen ? and are called aluminum silicates. The have

Jan 1, 1943

By Theodore L. Turner, Joseph H. Swift

A study on a small laboratory scale was made of the use of ammoniacalammonium carbonate for batch leaching Mn from low- grade manganiferous materials ( 6 to 16 pct Mn) obtained from deposits in the southern district of Aroostook County , Maine . These materials were partially reduced at 500 ° to 700 ° C with H₂ or CO and then leached with solutions of NH and CO₂ dissolved in water . Extraction of 80 to 90 pct of the Mn was obtained from some sample materials , but 10 to 34 pct of the iron was also extracted . Material from the Littleton Ridge deposit contained manganese intimately associated with Fe , a condition which contributed to difficulties in obtaining a commercially acceptable product . Extensive investigations of the leach and reduction processes with various mixtures of H₂ and water vapor , and CO and CO₂ , failed to disclose a set of conditions for selectively leaching the manganese . Finely divided metallic Fe was probably produced during the reduction steps so that Fe was leached with the Mn in the subsequent extractions .

Jan 1, 1964

By H. C. Miller

Several agencies of the Federal Government are engaged in research and fact finding relative to petroleum and natural gas, and others are concerned with carrying out the provisions of specific laws that affect these natural resources in their broad aspects. The Bureau of Mines, however, is the only Federal agency designated by law to engage in research in oil and natures gas production, chemistry, refining, and

Jan 1, 1941