Search Documents

By E. W. GOODWIN, V. F. Parry, J. B. Goodman, L. D. Schmidt, J. D. Davis, A. C. Fieldner, W. S. Landers, J. L. ELDER

The Heliopore process is essentially an arrangement that uses the waste heat in the exhaust gas of an internal - combustion engine to carbonize coal (noncaking ) or lignite . The gases distilled from the coal furnish fuel for the internal - combustion engine , which drives an electric generator . Thus the main products of the plant are electricity and char . A flow diagram illustrating the principles of operation of the Heliopore process is given in figure 1. The primary equipment consists of a carbonizing retort , gas cooling and scrubbing equipment, a gas storage holder, and an engine to burn the gaseous carbonization products . Coal is charged into the top of the retort while the hot gases from the engine travel upward through special ducts in the retort countercurrent to the coal flow . The hot gases never come into direct contact with the coal . Char is discharged at the bottom of the retort and hot gases at the top . The gaseous products resulting from carbonization of the coal are drawn off by an exhauster through the condensing and scrubbing equipment to take out tar and liquor , then to a gas holder , and finally are burned in a gas engine . The gas engine drives an electric generator and the engine exhaust gases are returned to the retort to carbonize coal . The entire process was intended to be continuous and self - sustaining, and to use coal as the only fuel . The plant may be said to be a large - scale pilot plant in that , although it is of full commercial size , its main purpose is to provide data for the design of others of its type . The installation tested had a daily throughput of about 4 tons of coal . Figures 2 , 3 , and 4 picture some details of the plant and equipment used in the experimental testing . Further details of the equipment and engineering drawings of the castings are shown in figures 8 to 22 in the Appendix .

Dec 1, 1943

By Changwoo Lee, Jan M. Mutmansky

"This paper results from the research at The Pennsylvania State University into establishment of standard procedures for characterization of respirable coal dust performed by the Generic Mineral Technology Center for Respirable Dust and supported by the U.S. Bureau of Mines and the Mining and Mineral Resources Research Institute at The Pennsylvania State University. The research performed within this particular project is oriented primarily toward standard methods of sampling and characterizing respirable coal mine dust underground so that the chemical, physical, and morphological characteristics are known and can be related to the incidence of coal workers' pneumoconiosis (CWP) in Pennsylvania.The research was initiated by con¬ducting a search of the literature to determine what coal and geologic variables may be related to CWP. The effects of coal rank, free silica content, the mass of respirable dust, and the level of trace elements were the major variables studied. It seems to be evident that the free silica content, the rank of coal, and the mass of respirable dust are the major concerns in defining the causes of CWP. However, based on the literature survey, the authors have concluded that verification of the causes of CWP is a multivariate problem and must be analyzed in an appropriate statistical manner.The results of a multivariate analysis of ten trace elements recorded on Pennsylvania coals are presented. Five of these trace elements were found to be of use in differentiating one coalfield from the others. Of these five elements, chromium and zirconium showed a strong positive correlation with the rank of coal while strontium showed a negative correlation.The design of the field sampling work and its application in future research is the final topic discussed. The sampling plan is oriented toward continuous miner sections with eight-stage impactors as the collection equipment. All of the field work will be conducted in the coal measures of the Allegheny Formation and above with both dust and channel samples being collected in the same mines.Coal workers' pneumoconiosis has been an important topic of concern to miners, mining engineers, and epidemiologists for decades. The general cause of the dis¬ease, the inhalation of coal mine dust, is well known, but the specific coal and geologic variables that affect the incidence and severity of the disease are still subject to debate and study. The primary objective of this study is to identify those variables of Pennsylvania coals that contribute to the CWP problem. To accomplish this task, a field sampling program is to be conducted to relate the characteristics of the coal dust, the coal seam properties, and the geologic variables to the occurrence of CWP.The first year of this study has been involved with both a literature review and experimental work oriented toward identification of causal variables related to CWP. The results of this work are presented here along with plans for implementation of the findings in future research.The previous studies of CWP causal variables have been conducted by scientists, engineers, and medical personnel. Many different types of studies have been performed with emphasis on interpreting the effects of dust mass concentration, mineralogy of the coal, the rank of the coal, and trace element concentrations upon the incidence of CWP in various coalfields. Most of the research has been conducted during the last two decades, with the British Isles, West Germany, and the United States being the primary countries involved.The review of the literature was conducted to determine which variables are likely to warrant further study in Pennsylvania. Previous research studies have related CWP to free silica and other mineral content, the rank of coal, the mass of dust in the working place, and the trace elements in the coal and lung dust. In the following sections, each of these topics will be discussed and analyzed."

Jan 1, 1988

By John E. Kelley

Laboratory equipment, which simulates abrasive impacts between steel and minerals that might be present during pneumatic transport of coal, was used by the Bureau of Mines to characterize the potential explosion hazard of such collisions in an atmosphere of fine coal dust, air, and methane. A variety of coal mine rock materials, including sandstone, limestone, and pyrite-bearing limestone, were impacted with specimens of pipeline steel. Tests were con-ducted in atmospheres containing zero to 6.4 vol-pct methane mixed with zero to 300 mg/l coal dust. Coal dust in air alone was not ignited by abrasive impacts, but additions of as little as 1 vol-pct methane to the coal dust and air mixture resulted in ignitions. Steel impacting against sandstone caused ignitions in mixtures of coal dust, air, and methane, and the probability for ignitions increased with an increase in methane. No ignitions occurred with impacts of steel on lime-stone or pyrite-bearing limestone, even when large showers of sparks were produced. Studies of the effect of tangential collision velocity showed that no ignitions of coal dust, air, and methane occurred below 900 fpm (4.57 m/sec). Ignitions in coal-air-methane mixtures were found to be caused by a hot friction-induced smear on the impacted rock at the impact site rather than by sparks. High-speed photography was used to verify this observation.

Jan 1, 1976

By Wallace W. Roepke

The Bureau of Mines studied the cutting characteristics of point-attack bits to reduce airborne respirable dust and energy during cutting. Linear cutting of two coal types using four bit types at three depths of cut with three space-depth ratios was performed with a modified horizontal milling machine using an optical particle-size monitor for respirable dust sampling. The cutting action of one bit on a rotary hardhead mining machine was mathematically analyzed and compared with the results of the linear cutting test. Airborne respirable dust per unit mass cut (specific dust) was found to be a monotonically increasing function of specific energy. Specific dust and energy decrease with increasing depth of cut. The amount of nonairborne respirable dust was 100 to 1,000 times greater than the airborne dust. The plumb-bob bit produced the most airborne respirable dust and the highest specific energy of the four bits tested. Rotary cutting was a greater dust producer and energy consumer than linear cutting because of the constantly changing depth of cut, space-depth ratio, and attack angle of the bit relative to the horizontal bedding planes. A new cutting technique is proposed to minimize the existing problems of the rotary cutting machines by providing greater production, reduced dust, and minimized methane ignition potential at the face.

Jan 1, 1976

By Richard D. Miller

This publication contains routine analyses and related source data for 350 natural gas samples from 19 States collected during calendar year 1362 as part of a continuous survey of the United States for occurrences of helium in natural gas. This survey has been conducted by the Helium Activity of the Bureau of Mines since 1917. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus. Four previous publications have been made to present the results of 5,648 gas analyses made by the Bureau of Mines, Helium Activity, prior to 1962. The first, Bulletin 486, 3/ contains analyses and data on 2,195 gas samples collected during the period 1917-47. Bulletin 576, 4/ the second publication, includes data and analyses for 1,575 samples collected from 1947 through May 1956. The third bulletin contains 1,444 analyses and source data of samples obtained from May 1956 to January 1, 1961.

Jan 1, 1964

By Richard D. Miller

This publication contains routine analyses and related source data for 350 natural gas samples from 19 States collected during calendar year 1962 as part of a continuous survey of the United States for occurrences of helium in natural gas. This survey has been conducted by the Helium Activity of the Bureau of Mines since 1917. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus. Four previous publications have been made to present the results of 5,648 gas analyses made by the Bureau of Mines, Helium Activity, prior to 1962. The first, Bulletin 486, 3/ contains analyses and data on 2,195 gas samples collected during the period 1917-47. Bulletin 576, 4/ the second publication, includes data and analyses for 1,575 samples collected from 1947 through May 1956. The third bulletin 5/ contains 1,444 analyses and source data of samples obtained from May 1956 to January 1, 1961.

Jan 1, 1964

By Sam S. Taylor

[The discovery of many oil fields in Illinois since 1936, and their rapid development have brought the problem of brine disposal to the foreground in that State. The ultimate magnitude of the problem is not yet known, but already it is treat enough to warrant technical investigation. The Bureau of Mines, therefore, has made a general survey of the methods of handling oil-field b brines in Illinois rend has studied in detail three subsurface disposal systems.]

Jan 1, 1940

By L. G. Marshall

The geology, mining, beneficiating, types of products, and costs in terms of percent of total costs and of labor, power, and supplies of two crushed-limestone operations in Madison County, Iowa, are described in this paper. The operations are basically similar, differing in refinements in mining, product types, and markets. The operations are comparable as to personnel and as to weighted costs in terms of percent of total costs and in terms of man-hours, power, and sup-plies. The waste-to-stone stripping ratio is 1 to 0.8 at both operations, the powder factor is 0.29 pound of explosives per ton of stone, and daily production is 95 tons per man-shift. Both companies use crawler-mounted diesel shovels for loading, truck transportation, wagon drills, and dry screening.

Jan 1, 1963

By Martin A. Elliott

The Bureau of Mines began its investigation of the use of Diesel engines underground to provide technical information necessary to assist this development in the United States. It was considered desirable to furnish such assistance because successful European developments/ in this. field had indicated that Diesel mine locomotives might be safer than electric trolley locomotives. The Bureau has recognized for some time the importance of eliminating the hazards associated with underground haulage systems using bare trolley wires. For example, each year 30 to 40 fatalities occur as a result of electrocution by contact with bare trolley wires. In 1943 and 1944, 101 men were killed and extensive property damage occurred as a result of mine fires started by falls of roof grounding the bare trolley wires.

Jan 1, 1948

By A. J. Kraemer

This paper on the physical and chemical properties of crude oils from California fields is one of a series of reports on the on the districts of the United States. The paper includes a short discussion of results, tabular data, and individual analyses of eight. California crudes. Analyses of other crude oils from California have been published it Reports of Investigations 2595, 2608, and 2846. The samples were obtained by members of the San Francisco office of the Bureau of Mines. The collecting 65 samples was facilitated by the courtesy of representatives of oil companies in California. The methods used in testing and analyzing the samples are described in detail in Bureau of Mines Bulletin 207. A discussion of the interpretation of crude-oil analyses, as made by the Bureau of Mines, is given in Bureau of Mines Report of Investigations 2806.

Jan 1, 1931

By Wilton Johnson

Native asphalt was produced in 1982 by five companies in two States, Texas and Utah. Bituminous limestone, used primarily as a paving material for street and road repair, was produced by White Uvalde Mines and by Azrock Industries, Inc., Uvalde County, Tex. Historically, gilsonite, a solidified hydrocarbon found only in Utah and Colorado, had been mined by American Gilsonite Co. and by Ziegler Chemical and Mineral Corp. from properties near Bonanza, Uintah County, Utah. During 1982, Hydrocarbon Mining Co., a subsidiary of the Oberon Oil Co., entered into a joint venture with Miocene Resources Inc. of Novato, Calif, to form Hydrocarbon Resources Co. for the purpose of mining gilsonite about 50 miles south of Vernal, Uintah County, Utah. Under the agreement, Hydrocarbon Mining contributed gilsonite-bearing properties held by lease or sublease as well as mining equipment to the venture. The property contained leases totaling 760 acres with probable reserves of 268,000 tons of gilsonite. Miocene Resources provided the partnership with a minimum of $200,000 to develop two of the leases and were to be responsible for management of the mining operations.2

Jan 1, 1983

By Nicholas Kyriazi

The Bureau of Mines has been developing breathing and metabolic simulator technology since 1970. Breathing simulation has been widely achieved throughout the world and used in the testing of open-circuit breathing apparatus, but satisfactory metabolism simulation has not been achieved. This situation required that the testing of closed-circuit breathing apparatus, which are the only type used in mines, be done using human test subjects. The goal was a machine that could accurately simulate both the breathing and the metabolic functions of a human being for testing of closed-circuit breathing apparatus. The advantages of using such a machine instead of a human being for testing respiratory protective devices lie in its ability to quantify metabolic input, its repeatability, and the lack of a need to deal with the vagaries of human subjects. This report will describe the breathing and metabolic simulators that have been developed and used by the Bureau over the past 15 yr.

Jan 1, 1986

By Manuel Gomez

A lignite from Milam County, Tex., has been oxidized by air at temperatures from about 27° to 300° C. for varying lengths of time. The oxidized coal was carbonized at 500° C. in a laboratory assay unit, and the products of carbonization were measured and analyzed. The data presented suggest that, as lignite is progressively oxidized, tar yields are decreased and gas yields are increased in a ratio approximating 1:1. It is surmised that tar-yielding structures in the nonoxidized coal produce gas, principally, when the coal is oxidized. Char-yielding structures of the nonoxidized coal give rise to additional water of decomposition after oxidation and pyrolysis. As lignite is subjected to greater oxidation, the gaseous product evolved on pyrolysis becomes almost entirely carbon dioxide. Tar yields decrease with an increased degree of oxidation, so that the reduction in tar yield may be used as a qualitative measure of oxidation. Pilot-plant drying and carbonization, where air is used as the transport gas and where some air is included in the drying and carbonizing gases, induces some oxidation of the coal particle. The short residence time in a fluidized system with reference to the oxidation environment limits the oxidation.

Jan 1, 1956

By Clayton M. Rumsey

The U.S. Bureau of Mines conducted a mineral resource survey of the Cinder Cones Wilderness Study Area (WSA) (CDCA-239), 10 miles east of Baker, CA, in 1983. The 44,299-acre WSA is underlain by Precambrian granite gneiss, Upper Cretaceous or lower Tertiary Teutonia quartz monzonite, and Quaternary basalt flows and alluvium. This mineral survey included an examination of two volcanic cinder mines, five lode prospects, two volcanic cinder prospects, and reconnaissance sampling in and near the WSA. The seven prospects are in the WSA; the two volcanic cinder mines are adjacent. No mines are in the WSA. In 1981, there were 61 placer and 3 lode mining claims in the WSA. Sample results from two prospects within the WSA contained significant gold and silver values; however, the mineralized rock is of limited extent and no resources were apparent. Alluvial samples taken throughout the WSA contained only traces of gold. Two volcanic cinder cones within the WSA contain an estimated 30 million tons of cinders. There are sufficient cinders outside the WSA to satisfy demand in the foreseeable future. Stone, sand, and gravel deposits are not resources because similar material is closer to markets. No evidence of energy minerals or geothermal resources was found.

Jan 1, 1985

By John W. Chandler

The property of the lava Cap Gold: Mining Corporation is in the Nevada City-Grass Valley mining district about 5 miles east of Crass Valley, Calif. At present (July 1940) the plant is mining end milling about 390 tons of gold-silver ore a day; about 310 men are employed. This paper describes the mining methods used and presents mining costs for 1939, when 60,704 tons were mined by cut-and-fill stoping and 55,676 tons by square-setting.

Jan 1, 1941

By H. Kenworthy

[Experimental studies were made to develop a laboratory technique for direct removal of cadmium and germanium from sphalerite concentrates. Cadmium- and germanium-bearing concentrates from the Illinois-Kentucky fluorspar field were sound to be, amenable to an inert atmosphere fuming process for removing these two moats in the form of gaseous sulfides. Treating the condensed fume by pyrometallurgical methods upgraded the material end provided a means of partly separating the constituents. Cadmium was concentrated about 35:1 arid germanium about 300:1. The extractive investigations were supplemented by vapor-pressure studies on the sulfides of germanium to obtain fundamental data for larger scale laboratory conditioning and control when treating the zinc concentrates. Vapor-pressure curves were developed for synthesized monosulfide and disulfide The results of these- investigations indicate the possibility of significantly increasing the recovery of cadmium from zinc concentrates. Comparison with present recovery of germanium cannot be made, since commercial recovery data arc not available.]

Jan 1, 1956

By Craig C. Hustwit

A pilot-scale treatment study was conducted on a copper-zinc bearing metal mine drainage using a pipeline treatment system called the In-Line System (ILS). The objective of this U.S. Bureau of Mines study was to determine whether the ILS could be extended from the treatment of coal mine drainages to the treatment of metal mine drainages. Hydrated lime (Ca(OH)2), quick lime (CaO), and caustic soda (NaOH) were used to neutralize the drainage. A novel reagent slurry of Ca(OH)2 and type C fly ash was also evaluated. Except for Ca(OH)2-fly ash slurry, treatment performance was evaluated for all reagents at pH values of 7,8,9, and 10. The Ca(OH)2-fly ash slurry was evaluated at a pH of 10. All reagents tested neutralized the metal mine drainage and substantially reduced the dissolved metal concentrations. It was concluded that the ILS could be useful in the treatment of metal mine drainages.

Jan 1, 2010

By H. B. Brunot, Ilsley. L. C., E. J. Gleim

"INTRODUCTION One of the various phases of the work by the U.S. Bureau of Mines, in its endeavors to minimize the hazards that attend coal mining, is the investigation of electrical motor-driven machinery. The object of this investigation is to foster the development of explosion-proof machines for use in gassy mines. This investigation is conducted under the provisions of Schedule 2C, which prescribes the inspection and tests made upon motors, controllers, and other electrical parts to determine their ability to withstand internal explosion without discharge of any flames. The method of conducting these inspections and tests is described in Bureau of Mines Bulletin 305, Inspection and Testing of Mine-Type Electrical Equipment for Permissibility, published in 1929. Formal approval of a machine for use in gassy mines is not granted by the Bureau of Mines until the machine is found to comply with the requirements, including inspection and test. When it is approved it is entitled to classification as a ""permissible"" machine.The high regard in which machines approved by the U.S. Bureau of Mines are held by engineers of other countries is attested by the growing number of shipments of permissible equipment; to other nations, including Australia, Russia, Norway, Japan, and Manchuria."

Aug 1, 1936

The accompanying supply/demand flow diagrams and 10-year tables for mineral and fuel commodities present essential data required by government, industry, and others to formulate policies and programs that can help assure an adequate and continuing supply of mineral raw materials. The 10-year data base terminates with 1975 figures because adequate world information was not available beyond that date. The selected mineral supply/demand tables and flow diagrams comprise but one "output" from the massive body of information and data collected and compiled by the Bureau of Mines on a continuing basis covering mineral production, consumption, prices, shipments, imports, exports, and stocks, as well as industry activities in all States and abroad.

Jan 1, 2012

By Manuel Gomez

This report presents experimental work conducted on a number of coals found within the boundaries of the Missouri River Basin, which were, to an extent, a selection of coals typical of that region. In the min, the laboratory work falls into three general classifications: (1) Laboratory distillation assay of coal to establish yields on carbonization; (2) chemical analyses of the coal samples before drying or carbonization; and (3) chemical analyses of the products of carbonization. It will be seen in the following discussion that these data derived from the small-scale laboratory apparatus are useful in predicting yields from pilot plants or industrial units. Coal is produced in about 48 general areas or mining fields in the Western States, of which approximately 18 fall within the limits of the Missouri Basin.3/ Beginning with the Northern Colorado field, through the Central and Western Wyoming fields, the coal is principally bituminous and subbituminous rank. The western Montana coals are also of these ranks. Progressing northeast from central Wyoming the coal decreases in rank, as shown by the subbituminous C coals of the Gillette field in northern Wyoming and the lignites of eastern Montana and North Dakota.

Jan 1, 1953