Search Documents

By A. T. Iannacchione

The Bureau of Mines established geologic factors affecting the mining of the Lower Kittanning coalbed to aid in coalbed minability studies and examined the occurrence of "wants" (places where coal is missing) and types of unstable roof rock strata. Trends established from mapping, including prediction of areas of high methane emissions, were extrapolated to unmined areas. 'Wants' in the coalbed are of two types: Erosional and depositional. Erosional features occur where north-south-trending sand-filled channels cut into the coalbed. Variations in depositional environments have caused the coalbed to "split" into several thinner units. Slickensides, commonly indicative of unstable roof, are adjacent to and on the underside of sandstone channels; they were caused by differential compaction and by soft sediment sliding along the contact between the sandstone and adjacent shale. The frequency of unstable roof also increases where the interval between the Middle and Lower Kittanning coalbed is less than 30 feet. The zones of weakness at the contacts above and below the Middle Kittanning coalbed are the controlling factors for unstable roof in these strata. Methane emissions from the coalbed are controlled primarily by depth, fracture permeability, and rank of coal. Local geologic factors are coalbed thickness, associated rock strata, structure, and proximity to outcrop.

Jan 1, 1979

By Gary P. Sames

Shale roof deterioration in coal mines. caused by ventilation air humidity fluctuations, is a common ground control problem. Shale roof deterioration often results in increased accidents, decreased production, inadequate ventilation, and increasing operating costs in maintaining haulage roads and airways. The results of Bureau of Mines research indicate that air tempering entries are an effective method of controlling deterioration prone shales. Some of the conclusions and recommendations drawn from Bureau research include (1) moisture sensitive shales will react adversely to moisture gains and losses, (2) the majority effect of specific humidity fluctuations can be concentrated in and absorbed by tempering entries, (3) tempering entry panels should be located as near to the main intake as possible, (4) tempering panels should be designed for a conservative recovery and provide a minimum of 20-to 30-min air residence time, (5) ventilation and escapeway requirements must be considered early in panel design, and (6) an efficient support and sealant plan can increase the life expectancy of a tempering panel.

Jan 1, 1985

By T. E. Gray

This report describes the preparation characteristics of the more significant coals in Dickenson County, Va. It is one in a series planned to determine which coals are suitable for the production of metallurgical coke either as mined or after beneficiation. Nearly 4 million tons of coal was produced in Dickenson County in 1955, of which approximately 2.7 million tons was cleaned mechanically in 5 cleaning plants. The Federal Geological Survey has estimated that nearly 1,300 million tons of measured and indicated coal reserves remained in the county as of January 1, 1951.

Jan 1, 1958

By H. R. Wells

The Blackbird district, Lemhi County, Idaho, has long been recognized as a potential source of cobalt and copper. However, the comparatively low grade and small size of the known ore bodies, the small demand for cobalt, and. the lack of adequate roads throughout the region precluded extensive exploration of the early discoveries in the area. Recent advances in alloy metallurgy, accentuated by wartime activities, greatly increased the demand for sources of domestic cobalt. Beginning In 1941, engineers of the Bureau of Mines conducted an examination and exploration program in the Blackbird district. This work was supplemented by an exploration program by engineers of the Howe Sound Mining Co., 730 Fifth Ave., New York 19, N.Y.

Jan 1, 1948

By L. Keith Hudson

The purpose of this study is to provide data that demonstrates that the Alcoa flash calciner design can be used for the decomposition of AlCl3?6H2O to A1203. Heat and material valance data for calcination provides data on the partial pressure of HCl in the off-gases. Experimentally determined data for the HCl partial pressure, over solutions expected in producing alumina from clay by the hydrochloric acid process, show that HCl can be absorbed from the off-gases into process solutions to effect crystallization of AlCl3?6H2O.

Jan 1, 1979

By Forrest T. Moyer

To keep the mineral and allied industries informed of trends in the causes of accidents and to point out the need for corrective measures, the Bureau of Mines collects, analyzes, and periodically published health and safety statistics. This report includes data for 1964 on injury experience, with related employment statistics, at coal mines in the United States. These data are presented in tabular form under the following headings: General Injury Experience Tables 1 to 6: Current data on number of injuries, degree of injury, frequency and severity rates, average severity, and related employment and production data by work location.

Jan 1, 1967

By John C. Edwards

The Bureau of Mines developed a mathematical model to predict the oxygen requirements for a miner evacuating a mine. The model accounts for variations in the miner's escape speed with mine airway height, and for the empirically determined expressions for the weight-specific oxygen uptake rate for upright walking, stooped walking (duck-walking), and crawling. A Fortran computer program that is user oriented was prepared based upon the model's constitutive equations. Specific instructions for utilizing the program, as well as applications to miner evacuation from a mine, are presented.

Jan 1, 1986

By Daryl R. Tweeton

The Bureau of Mines conducted experiments to measure the influence of environment on the friction and wear of a steel-quartz system at several speeds and loads. In each test a quartz block was pressed against a rotating ring of low-carbon steel. Environments used were moist air, dry air, dry nitrogen, water, aqueous oleylarnmonium acetate (ClsH35NH3+-OCOCH3), and aqueous aluminum chloride (A1C13). The sliding speeds were 2.2, 13, and 33, cm/sec, and the loads were 6.8 and 13.6 kg. The coefficient of friction, the wear, and the roughness of the surfaces were measured, and the wear debris was examined. The coefficient of friction was significantly lower in moist air at 2.2 cm/sec than for any other combination of environment and speed employed, and was generally an inverse function of the oxidizing ability of the environment. The coefficient of friction increased somewhat with increasing load. The wear of the steel rings was greatest in dry air at all speeds and loads. The wear of the quartz blocks at 180 rpm was greatest in dry air, but at 12 rpm it was greatest in nitrogen. Friction and wear in aqueous oleylarnmonium acetate and in aqueous aluminum chloride were similar to effect in water alone.

Jan 1, 1976

By Jerry E. Olson

In 1986, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied part of the 20,071-acre South Fork Wilderness Study Area (OR-005-033) and part of the 8,791-acre Sand Hollow Wilderness Study Area (OR-005-034) in order to evaluate their identified mineral resources. The study areas are located in Crook County, OR, about 58 air miles east from Bend. The areas studied are underlain by Tertiary- and Quaternary-age volcanic and tuffaceous sedimentary rocks. No mineral resources were identified in or adjacent to the study area. Except for common opal and agate occurrences along the northern boundary of the study areas, no mines, prospects, or mineralized zones occur within the study areas. Bentonite is periodically mined less than 1 mi southwest of the Sand Hollow study area boundary. Neither of the study areas has geothermal leases, but both areas are under lease for oil and gas.

Jan 1, 1987

Minerals are a fundamental component of the Nation" material and economic base. Without a continuous supply of minerals to meet growing and changing needs, the basic character of our society would be very different. The importance of minerals to the United States was reemphasized by the Congress in I970 when it enacted the Mining and Minerals Policy Act, which stated that it is the continuing policy of the Federal Government in the national interest to foster and encourage private enterprise in (I) the development of economically sound and stable domestic mining, minerals, metal and mineral reclamation industries, (2) the orderly and economic development of domestic mineral resources, reserves, and reclamation of metals and minerals to help assure satisfaction of industrial, security and environmental needs, (3) mining, mineral, and metallurgical research, including the use and recycling of scrap to promote the wise and efficient use of our natural and reclaimable mineral recources, and (4) the study and development of methods for the disposal, control, and reclamation of mineral waste products, and the reclamation of mined land, so as to lessen any adverse impact of mineral extraction and processing upon the physical environment that may result from mining or mineral activities.,.

Jan 1, 1977

By Gary P. Sames

The Bureau of Mines recently initiated a study of geologic features that contribute to roof instability in western U.S. underground coal mines. The purpose of the study is to provide information for use in ground control planning and safety hazard reduction in that region, where mining activity has been increasing. Hazardous geologic conditions were surveyed in selected underground coal mines in Utah and Colorado, and both depositional and structural features were identified as potential ground hazards. Although the conditions found do not differ in kind from hazardous geologic conditions in the Eastern United States, they do differ in intensity of occurrence and relative importance. Three depositional features dominate where unstable roof occurs in western underground coal mines: paleochannel deposits, crevasse splay deposits, and flood basin deposits. Three structural features identified as hazardous, but not so widespread or common as the depositional hazards, are faulting, jointing, and igneous intrusions. This survey establishes a foundation for future studies aimed at reducing and preventing ground control accidents in western coal mines.

Jan 1, 1988

By R. W. Stahl

Gas accumulation and dust suspension are the major safety hazards in coal stockpiling and reclaiming operations. This report presents a schedule of safety precautions and plant design features devised by the Bureau of Mines to reduce danger from these and other sources.

Jan 1, 1965

By Donald W. Mitchell, John Nagy, Edwin M. Murphy

"Investigations in the Federal Bureau of Mines Experimental coal mine near Pittsburgh, Pa., have shown that high-expansion foam containing at least 0.2 ounce of water per cubic foot of volume is effective in controlling exper-imental underground coal, oil, or wood fires. Some of the fires were extinguished, but more of the coal and wood fires were brought under enough control to permit direct attack with water or other extinguishing agent or loading the hot material into cars. The largest controlled experimental fire, which burned about 5 hours before attack, was in a coalbed 5 feet wide, 10 inches thick, and 100 feet long. The greatest distance foam was transported to control a fire was 1,010 feet.An incipient fire should be attacked promptly with water, rock dust, or other approved and readily available extinguishing agents. Where heat, roof falls, and smoke prevent direct approach, the more involved procedure of using foam may be advantageous. The effectiveness of the foam in controlling a deep coated fire of considerable extent H,vet to be proved by actual trials in aSome hydrogen, carbon monoxide, and methane gases are generated when a fire is attacked with foam. Calculations showed that in experimental fire tests an explosive mixture could form; however, this would occur only within a narrow range of combustible gas-air mixtures not likely to be found in practice. The principal explosion hazards are due to generation of gases by the foam, localized build-up of normally liberated methane, and volatiles liberated by the coal during heating. The quantity of combustible gases generated by the action of the foam on the fire is about the same as that when an equivalent amount of water is applied."

Mar 1, 1960

By G. G. Campbell

The Bureau of Mines initiated a field test of underground coal gasitication to investigate the technologic feasibility of gasifying a subbituminous coal. The test site is near the town of Hanna, Wyo., about 70 miles northwest of Laramie. Preliminary results of the experiment are described. The coal was ignited in the central well of a 16-well pattern. Both forward and reverse combustion techniques were attempted to prepare a path of sufficient permeability to permit the high air injection rat s necessary for gasification. Gasification between linked wellbores was sustained for periods as long as 3 months. Hydrogen-rich gas having a heating value of 100 to 150 Btu/scf was produced.

Jan 1, 1974

By C. L. Brown

Among the more recent developments for breaking coal in mines is the Airdox system, in which high-pressure compressed air is conducted to the points of application by means of heavy-duty steel and copper tubing. Stray electric currents can be detected on y of the compressed-air lines, and evidence of such currents is rev led, by arcs and sparks when contact is made between the tubing and mine track or other equipment forming a current path with the track. Explosive gas is liberated in many coal mines; therefore, from the standpoint of safety, it is desirable to eliminate all possible sources of gas ignition, including stray electric currents. The purpose of this report is to reveal the source, magnitude, and possible methods of controlling stray currents in compressed-air lines that are used in connection with Airdox systems. Stray electric currents have been studied in most coal-mining localities in the United. States where Airdox equipment is used. The information given in this report is based on the find of these studies.

Jan 1, 1949

By Hanns J. Billmayer

This report, which covers the period from June 15, 1974 to May 30, 1975, describes the work performed in compliance with the requirements of Contract No. H0242065 and modifications 1, 2, and 3 thereto. The purpose of the original contract was to equip the second shuttle car in the Jewell Ridge No. 12 mine, section 6R, with a refined design canopy and seats. In addition, several refinements and improvements were to be designed and installed at the same location on the cutter and the loader. However, during October 1974 in response to a request from the Technical Project Officer, the contract was modified to eliminate all of the cutter and loader tasks and substitute the design, fabrication, and installation of an improved canopy on the no. 2 roof drill in the above mentioned section of the Jewell Ridge No. 12 mine.

Jan 1, 1975

By Richard P. Walters

This Bureau of Mines report reviews and assesses the technology for preparing electrodeposited coatings of the platinum-group metals from molten alkali metal cyanide baths. Methods are described for the preparation and purification of the cyanide electrolyte. Vacuum drying, fusion, and purity of the cyanide salts are discussed. Use of a sodium borosilicate test tube as a sodium-ion-conducting membrane for the addition of the desired platinum-group metal is described. The optimum plating parameters of potential and current density for Pt, Pd, Rh, Ru, and Ir coatings that result in the best deposits are given. A method for producing platinum-rhodium alloy coatings of predetermined composition is also described. The importance of careful substrate surface preparation is illustrated. While problems still remain with respect to coating porosity, careful application of the methods described permits the preparation of adherent, coherent electrodeposited coatings of the platinum-group metals.

Jan 1, 1984

By R. D. Ladoo

"At the beginning of 1920 a general feeling of optimism was noted in many talc-producing districts. The industry seems to have recovered from the temporary depression of the first half of 1919 and many mills are running at capacity production with their entire output for 1920 contracted for. The imports of talc for 1919 were only slightly larger than in 1918 by weight and probably no more by value. Thus foreign competition has not begun to be seriously felt. Several new companies in this country have been organized, some to operate new deposits and others to continue the work done by others.An interesting phase of the present situation is the possibility of increased use of talc in paint. There is a shortage of barium sulfate used as,paint filler. Since, for some uses, talc is considered second only to BaSo4 as a filler for paint, it is possible that part of the shortage could be relieved by an increased use of talc.A series of physical tests upon all pigment materials used in the manufacture of paints is being conducted for the Paint Manufacturers Association of the United States. It is important that all types of talc be represented in these tests. Producers of finely ground talc, 200 mesh and finer, are urged to submit samples of at least two pounds each of these grades that are available to paint makers with trade name and quality data, to the Institute of Industrial Research, 19th & B Streets, Washington, D. C., where the tests are being conducted.The Talc Products Company, Inc., Washington Building, Los Angeles, California, has recently been organized to develop a large body of talc one mile north of Riggs, San Bernardino County, California, This deposit contains a compact, white talc which can be sawed into crayons. The company's mill, at Los Angeles) is equipped with a unit of the Raymond system of grinding and air separation, and pencil sawing machines. It is reported that the pencils are being successfully used in Pacific Coast ship yards.The mining of talc where no mill is owned by the operator and the consequent sale of talc in its crude massive state has not proved profitable in a number of cases recently noted. Under exceptional circumstances, where mining costs are low and the product can be sold to a mill near the mine, the operation maybe profitable, but this condition is not common. One mine of this type has recently closed down, at least temporarily; but a second, more fortunately situated, in another district, is continuing operations, although plans are being made to erect a mill in the early spring. Most satisfactory results are ordi¬narily obtained where the mine and mill are owned by the same company.The sale of the Balmat mine of the International Pulp Company, near Gouverneur, N. Y., to J. H. McLear, Gouverneur, and H. G. McLear of New York, has been reported. It is stated that a large part of the property has been already leased to the Sylvia Lake Company, who will operate it. ""Cement, Hill, and Quarry""* states that ""the first mining done on this property was for silver and lead, but it developed into a good zinc producing property and later it was worked for its talc deposits. It has passed through several hands, the American Pulp Co., the Union Talc Co., and the International Pulp Co., all having had it in successive periods since 1891."""

Jan 1, 1920

By Forrest T. Moyer

The overall disabling work injury experience, excluding office- workers, at nometal mines and mills during the period 1961-63, as reported to the Bureau of Mines by operators, was 77 fatal and 7,201 nonfatal injuries during an aggregate worktime of 335,029,685 man- hours. These injuries, fatal and nonfatal combined, occurred at a frequency rate of 21.72 per million man-hours, comprising 0.23 for the fatal and 21.49 for the nonfatal injuries. The combined severity rate of the disabilities was 2,312 days lost or charged per million man-hours, consisting of 1,379 for the fatal and 933 of the nonfatal injuries, The average severity of all disabilities during 1961-63, was 106 days per injury, The number of days lost or charged, excluding officeworkers, at nonmetal mines and mills during 1961-63, was 462,000 days charged to fatal injuries and 312,461 days lost from nonfatal injuries. The outstanding causes for fatal injuries were explosions (18 fatalities occurred in a major mine-explosion disaster in a potash mine in Utah in 1963) and falls of rock or ore from back or side, while most nonfatal injuries were caused by handling materials, slips or falls of persons, haulage, and machinery. The parts of the body most frequently injured during the period 1961-63 were the trunk, hand and finger, and foot and toe, An average of 52,810 men were at work daily, There were 20 nonfatal disabling injuries reported for office- workers at nonmetal mines and mills during the period 1961-63 during an aggregate worktime of 23,088,496 man-hours, These injuries occur- red at a frequency rate of 0.87 per million man-hours, There were no fatal injuries reported.

Jan 1, 1967

By Harold J. Barnett

In January 1948 , the Secretary of the Interior directed that a study be made of energy resources and requirements that would provide a basis for continuing appraisal of the adequacy of the Department's programs in the energy field . That this instruction was timely has been demonstrated by the increasing interest being evidenced by Congress , industry , labor , and the public in the future of the energy segment of our national economy . Several studies of individual energy sectors have appeared . Various legislative proposals have been made in Congress for obtaining more information on this subject . Substantial interest in energy projections is not , of course , a recent innovation . Energy availability and consumption are strategic factors in peacetime prosperity and growth and in our national defense as well . The past generation's literature of earnest public discussion and of legislative consideration of matters involving energy projections is very extensive . This is an exploratory study produced in the Program Staff of the Office of the Secretary of the Interior in the first half of 1949 and revised recently to take account of certain of the preliminary energy data from the 1947 Census of Manufactures and critical comments . It is offered at this time solely as a technical contribution in economic research technique . As the Bureau of Mines has recently undertaken to revise this preliminary study , critical and other comments are invited .

Oct 1, 1950