Search Documents

By W. M. Merritts

The control of coal dust created and released during the operation of continuous mining machines in bituminous-coal mines of the United States is a problem. The interest manifested in this problem indicates the seriousness of the hazards involved, particularly when the dust has not been abated at its source and has become air-borne. Officials of the Sunnyside No. 1 mine, Kaiser Steel Corp., were confronted with the problem of abating the coal dust created by operation of a recently installed continuous-mining machine, and they requested the aid of representatives of the Coal-Mine Inspection Branch, Bureau of Mines, United States Department of the Interior, in developing an effective method of allaying the coal dust at its source.

Jan 1, 1951

By L. Y. Sadler

The Bureau of Mines conducted a study Lo determine the loss in weight of silica (Si02) volatilization from low-alumina (A1203) refractories used as hot face liner materials in such process equipment as coal gasifiers, synthesis gas transfer lines, and ammonia plant secondary re-formers. Small specimens of 80-and 40-pct-A1203 brick and 95-pct-SiO2 brick were exposed to steam in high-pressure furnaces at pressures of up to 1,000 psig and temperatures up to 1,400° C for periods ranging up to 120 h. Weight losses from the 40-pct-A1203 brick after 40 h of exposure were highest, 2.75 pet at 1,400° C and 1,000 psig. The rate of weight loss had dropped to near zero after 80 h of exposure at all temperatures. No relationship between total silica content of the specimen and weight loss could be established nor did scanning electron microscopic examination of the specimens before and after exposure identify specific regions (e.g., surface) suffering a disproportionate share of the silica loss. It was concluded that minor silica volatilization is likely to occur, if at all, at temperatures of less than 1,000° C and pressures below 1,000 psig, and that low-alumina refractories should be used as dry-ash coal gasifier hot face linings.

Jan 1, 1986

By H. S. Chiang, S. S. Peng

"SummaryAir velocity distribution surveys on four mechanized longwall faces are presented and discussed. Although there are discernible patterns in the velocity distribution, there are wide differences in distribution in the cases examined. This can be attributed to differences in mining and face geometry. An important factor is air leakage into the goaf.IntroductionOver the past two years several intensive air velocity surveys have been carried out in West Virginia coal mines as part of a programme aimed at understanding dust transport mechanisms on mechanized longwall faces. These are presented here and some of the patterns of velocity distribution are discussed.Ventilation survey methodologyThe air velocity vector consists of three mutually perpendicular subvectors; the vertical subvector is directed toward the roof, one of the horizontal subvectors is parallel to the coal face and the other pointing to the gob. The air velocity which was measured in this paper is the horizontal subvector parallel to the coal face.To record the velocity distributions at the longwall faces, the surveying stations and the surveying points were established as follows.(1) The first station usually was set at the third support from the headentry T-junction. Within the first few supports, the air coming from the intake airway encounters a sharp right-angle turn at the T-junction, and forms a turbulent region close to the coal face. The intake air in this region is also influenced by the motors that drive the face conveyer. But when the air reaches the different. But for the same face the number was the same. The main air-travelling area was divided into six to 12 equally sized sub-areas, and each surveying point was situated approximately at the centre of the sub-area.The velocity survey was carried out by two persons, one reading the meter and the other taking down the readings. A complete survey at one station took about 5-8 min. Usually, the dimension of the cross-sectional area was measured during that time.A third person used the smoke tubes to observe the following: (I) the air movement patterns at different locations; (2) the extent and the direction of the air leakage; and (3) the machines' influence on the main airflow. At the same time he observed and recorded the roof conditions and the compactness of the roof-caving in the gob."

Mar 1, 1989

To develop a reliable, remotely-controlled, mobile roof support to eliminate the need to set posts, cribs, or props while extracting coal pillars. Approach The primary danger during pillar extraction is premature caving of the mine roof. The roof must cave predictably and dependably to ensure the safety of miners. Support during retreat mining is usually obtained by setting posts, cribs, props, roof bolts, or a combination of these devices. These are set manually by miners in the working area. To help minimize the danger to mine workers and to equipment posed by premature falls, the Bureau of Mines developed the mobile roof support (MRS) system to secure the roof during pillar extraction. How It Works The Mobile Roof Support (MRS) is eight-feet-wide, ten-feet-long and five-feet-high, with twelve inches of ground clearance. It is ruggedly built and exerts less than 20 psi ground pressure. The MRS is powered by a 40-hp, 460-v AC permissible motor. The reversible, variable tram speed is 80 ft/min on a 20-percent grade. It is tire-mounted, has a trailing cable, and is remotely controlled either by a radio or a tether communication cable. The machine carries four 50-ton jacks which serve as props for working heights from seven to fifteen feet. Two jacks are chassis-mounted and two are on swing arms. Each jack has a cap which distributes the roof load to three paints. The swing jacks form a breaker row to stop falling roof and prevent caving Into the work area. One jack has a visual load indicator and a second is wired to the machine lighting system. Blinking lights indicate when the preset loading is being exceeded. In the case of excessive loads, an ability to remotely jettison either or both swing jacks has been incorporated into the system to permit removal of the MRS while the roof is still supported.

Jan 1, 1985

By R. J. Leary

Iron and steel scrap has accounted for 45 to 50 percent of the metallics used by the steel industry. In an electric furnace which utilizes a 100-percent cold charge consisting of about 99 percent scrap and 1 percent pig iron, sensible heat from molten pig iron is not present as it is when hot metal is charged to open hearths and converters. A study of means for more efficient utilization of iron and steel scrap in steelmaking indicated that the time and fuel requirements to melt scrap were important cost factors, particularly in arc-furnace steelmaking. A process to preheat scrap economically prior to charging into the arc furnace has been developed, utilizing efficiently the heat from combustion of fossil fuels as a substitute for electric-arc heating in the initial stage of arc-furnace steelmaking. Scrap is loaded into a portable vertical cylindrical furnace body that is open at the top and has a perforated dropout door at the bottom. In the heating operation, the furnace body containing scrap is placed upon a hollow base connected to a flue, and then the burner and combustion-chamber unit is lowered on top of the furnace body. The stream of hot-combustion products flows down through the bed of scrap imparting heat to it, and the cooled gases exhaust through the flue. After the heating operation the furnace body containing hot scrap is transported to the arc furnace for charging. Thus, the furnace body serves as a charging bucket for top-charged arc furnaces, enabling this preheating process to be integrated into existing material-handling patterns in many arc-furnace plants.

Jan 1, 1961

"When a metal-mining company takes out a workmen's compensation insurance policy, it does so to relieve itself of its uncertain and variable financial liability under laps requiring payment to employees for lost-time accidents, there-by passing the liability or to the insuring agency. For this service, or rather for the assumption of the risk, the insuring agency charges the mining company a price, or in insurance parlance, ""a premium"".The insuring agency depends upon a volume and variety of business to average the losses incurred by its individual policy holders, and determines its price to cover losses that are suffered and its cost of doing business.It is generally known that all types of insurance are founded on the theory of probability applied to large groups of risks, Workmen's compensation insurance is no exception, and the average price paid therefor must be based on the frequency and severity of accidents in the particular industry or branch of industry under consideration. The frequency and severity rates are determined by statistics, which, of course, unless standardized, kept carefully and consistently, and analyzed properly, are liable to be inaccurate and misleadingThe importance of large groups in arriving at an average price for insurance service can not be overestimated, For example the writer knows of one small group of some twenty metal-mining companies whose losses during the past two years exceeded their premium charge by 54%. Not a single individual company during the two years kept its losses below the premium rate. For several years the group as a whole has persistently exceeded its premium rate, Such risks are not profitable to the insuring agencies and can only be carried where a large volume of good risks will balance the poor risks, but in order to conform to good insurance ethics the premium rate must be based on averages for the industry as a whole, and kept sufficiently low to induce operators to sell their risks."

May 1, 1924

By Gustav Wade

"INTRODUCTION Analyses of samples of crude oil from several Texas oil fields have been published from time to time in Bureau of Mines reports, some of which are out of print, but many other analyses of Texas crude oils have not been published. The purpose of this paper is to make available in condensed tabular form under one cover all analyses of the Texas crude oils that have been examined by the Bureau of Mines.DIVISION OF TABLEThe table of analyses is divided into six parts in accordance with the geographic subdivisions of the State. (See fig. 1.) This grouping of the oils corresponds only in a general way with the principal formations in each area from which oil is being produced. In general, the principal oil-producing formations in the Texas Panhandle and West Texas areas are of Permian age; those of North Texas are of Pennsylvanian and older ages; those of the East Texas Basin and of Central Texas are of Cretaceous age; and those of the Texas Gulf Coast are of Eocene and younger ages.For convenience in presentation the name of the geologic age has been assigned to each group of the table although same of the oils included in the group may be of another age.Group 1 includes oils of Permian age produced in the Texas Panhandle area, which comprises the following counties: Dallam, Sherman, Hansford, Ochiltree, Lipscomb, Hartley, Moore, Hutchinson, Roberts, Hemphill, Oldham, Potter, Carson, Gray, Wheeler, Deaf Smith, Randall, Armstrong, Donley, Collingsworth, Parmer, Castro, Swisher, Briscoe, Ball, and Childress."

Dec 1, 1934

By R. R. Brandenthaler

A series of open-flow tests was conducted in the Chickasha gas field, Grady County, Oklahoma, during June, 1927, under the direction of the U. S. Bureau of Mines and at the request of the Oklahoma Corporation Commission. The purpose of these teats was to determine whether or not any differences existed in the open-flow volume of a gas well when taken through well-head nipples of different diameters, and further, to establish if possible a relationship between open-flow volumes taken through well-head nipples of various diameters. The open flow of a well is the volume or quantity of gas, measured under standard conditions, that a well will produce when open to the atmosphere. There are several methods used for determining the open flow of wells; some of the methods are more suitable under certain conditions than others. The Pitot tube method is the simplest, is applicable to almost any condition, and is the one most commonly used. In the tests described in this paper no attempt was made to compare the Pitot tube method with the minute pressure measurement method or the orifice measurement method.5

Jan 1, 1928

By W. M. Mark

This investigation was undertaken to develop methods to improve the quality of titanium sponge produced by the Bureau of Mines modification of the Kroll magnesium reduction process. Research revealed that by systematic elimination of detrimental impurities introduced with the raw materials and by improved handling and processing techniques, high-quality ductile titanium with a hardness of less than 110 B.h.n. (Brinell hardness number) can be produced consistently. This improvement was accomplished by helium (or argon) stripping of residual atmospheric and other dissolved gases from the titanic chloride, preliminary dehydration of crude titanium sponge, and careful regulation of the titanium tetrachloride (TiC14) feed rate to the reactors.

Jan 1, 1960

By Frank C. Andreuzzi

The Federal Bureau of Mines conducted a demonstration project to reclaim 125 acres of abandoned strip-mined land in Lackawanna County, Pa., for public recreational, historical, and educational use as a park. The Bureau was involved in the development of the general site plan, and engineered and supervised the basic land rehabilitation. The park's Facilities include outdoor recreational activities, picnic grounds, children's play areas, primitive overnight camping, and winter sports. A major attraction is the Anthracite Museum constructed by the Pennsylvania Historical and Museum Commission The project may serve as a prototype for reclaiming existing and future surface-mined lands.

Jan 1, 1976

By Rodney D. Rosenkranz

Energy consumption in domes tic copper production has increased nearly 60 percent in the last 10 years, reaching approximately 175 trillion Btu in 1973. Energy required to produce 1 pound of copper rose from nearly 41,000 Btu in 1963 to nearly 50,000 Btu in 1973. Production from lower grade ores and strict pollution control regulations have contributed to this increase. Each stage of copper production has been analyzed to determine total energy consumed, energy mix required, cost of the energy, and recent or proposed changes in operations which may affect the consumption of energy by the copper industry. Data have been gathered from a recent Bureau of Mines canvass of the industry, from visits to copper operations, and from conversations with copper industry officials.

Jan 1, 1976

By Jeffrey Shawn Peterson

The testing procedures of the u.s. Mine Safety and Health Administration specify that intrinsic safety acceptance tests be conducted using a standard tungsten-cadmium electrode configuration in the break-flash apparatus. However, in realistic mining environments, other materials may be more likely sources of sparking. Information defining the probability of spark ignition between common materials such as aluminum, brass, copper, lead, tin, cold-rolled steel, and stainless steel is of more practical value in determining ignition hazards. The U.S. Bureau of Mines has completed an investigation of the influence of material on the ignition probability using the breakflash apparatus. By comparing ignition currents or ignition voltages corresponding to a probability of one ignition per thousand sparks to those found previously for cadmium, a margin of safety may be estimated for each material. This report presents the results of an investigation into the influence of disk electrode material on the probability of ignition.

Jan 1, 2010

By J. Adkins

This document presents a description of the results of a project aimed at producing a broad description of current mining training programs and an evaluation of their effectiveness with respect to reducing mine injuries. Aggregate training and injury data were used to evaluate the overall training effort at 300 mines as well as specific efforts in twelve categories of training course objectives. From such evaluations, recommendations were derived with particular emphasis being placed on identifying program characteristics that tend to be associated with effective training. Recommendations were also formulated with reference to role changes in industry and government interaction with respect to training programs, new or additional training programs, changes in the types of course materials and training methodologies, and recommendations concerning new areas for investigation.

Jan 1, 1976

By F. R. Lee

[WHEN the Bureau of Mines was established in July 1910, one of the problems immediately attacked by the new organization was the development of standard, for the design and testing of electrical equipment that could be used without fear of initiating fires and explosions in underground coal mules. Research and investigation by Bureau personnel, supplemented by the published results of similar work by European mining authorities, led to the establishment of standards or "schedules." which guide manufacturers in the design of many types of electrically operated machines and devices used in. underground coal Mining. By issuing these standards, Bureau personnel establish the requirements to be met by such equipment before it tan be approved by the Bureau of Mines as permissible for use in gassy coal mines. Every 2 years the Bureau of Mines publishes a list of equipment that leas been accepted as approved or permissible during the preceding 2 calendar years. This is done to inform the mining industry of the availability of the latest equipment for safe use underground.]

Jan 1, 1964

By F. R. Lee

When the Bureau of Mines was established in July 1910, one of the problems immediately attacked by the new organization was the development of standard, for the design and testing of electrical equipment that could be used without fear of initiating fires and explosions in underground coal mines. Research and investigation by Bureau personnel, supplemented by the published results of similar work by European mining authorities, led to the establishment of standards or "schedules." which guide manufacturers ill the design of many types of electrically operated machines and devices used in underground coal Mining. By issuing these standards, Bureau personnel establish the requirements to be met by such equipment before it tan be approved by the Bureau of Mines as permissible for use in gassy coal mines. Every 2 years the Bureau of Mines publishes a list of equipment that leas been accepted as approved or permissible during the preceding 2 calendar years. This is done to inform the mining industry of the availability y of the latest equip¬ment for safe use underground.

Jan 1, 1964

By Clinton C. Knox

Attention of mine operators and engineers in the Picher zinc-lead field has been drawn increasingly in recent years to marginal ore deposits lying at greater than normal depth below surface in the marked structural depressions known as the Miami and Bendelari troughs. Not only mining but prospect and development drilling is relatively costly in the bottoms of the structural depressions known as the. Miami and Bendelari troughs which cross the center of the Picher field. Nevertheless, operations by various mining companies in recent years have shown that no insuperable problems exist, and with the gradual lowering of grade cut-offs throughout the field, certain potential deep-ore areas, previously only partly explored seemed worthy of further investigation. Some such areas were called to the attention of Bureau of Mines engineers by lease holders and operators, while others were noted in the course of Bureau's systematic investigation of Tri-State ore reserves. The writer was assigned to make a study of. those possible "trough extensions," in the course of which all available nine maps, drill logs, and prior reports were assembled. Subsequently 41 churn drill holes were bored by the Bureau in the periods October 1944 to May 1945 and October 1946 to April 1947. The general area under investigation this project is indicated on figure 1, which likewise shows its relation to nearby towns, roads, and railroads. The location of individual deposits included in the report is indicated more clearly on figure 3. Minable ore was found in only two holes, and the structural information procured by drilling was less encouraging than anticipated. This report, however, presents all factual data obtained, in the belief that they may be useful in subsequent prospecting and development projects in the areas investigated. There are also set forth some of the stratigraphic data relative to the Picher field ns a whole and the Miami and Bendelari troughs which were assembled in the preliminary investigation of this project.

Jan 1, 1949

By J. E. Chilton

The Bureau of Mines has developed a portable flammable gas detecting system for estimating the flammable gas concentrations in a mine containing one or more combustible gases at concentrations up to 100 vol pct. With this portable detecting system, mine rescue or recovery personnel can quickly determine if they are working in a potentially explosive gas atmosphere and either leave the area or make appropriate changes in the fresh air ventilation of the mine to render the area safe. The detecting system uses a commercial, intrinsically safe, flammable gas detector with a range from 0 to 5 vol pct methane (CH4). The flammable gas detector has a catalytic heat-of-combustion sensor that can detect all flammable gases that would be encountered in a mine including methane (CH4), ethane (C2H6), carbon monoxide (CO), and hydrogen (H2). To determine the mine gas concentration, the rescue worker dilutes a sample with fresh air carried within the detecting system. The concentration of the diluted sample is then measured with the permissable flammable gas detector. The actual mine gas concentration is calculated from the product of the indicated diluted gas concentration and the system dilution ratio using a pocket calculator or the nomograph on the side of the unit.

Jan 1, 1987

By James H. Gary

Data regarding the composition and physical properties of Florida land-pebble phosphate-waste slime are presented, and the feasibility of dewatering and beneficiating the slime by several different methods is discussed. Chemical analyses, electron micrographs, and X-ray diffraction data showed that principal constituents of the slime included quartz, attapulgite, and flaorapatite. Viscosity of the slime changed with pH; thixotropic, Newtonian, and rheopectic states were observed as the pH increased. Use of various flocculating agents was not effective in improving thickening properties of the slime. Dewatering tests using pressure filtration showed that temperature influenced the filtration rate more than pressure; the filtration rate at 165° C was tenfold that at room temperature. Selective flotation of the slime, using two different processes, gave promising results. About 25 pct of the phosphate was recovered in a concentrate assaying 31 pct P205, Other tests demonstrated that the slime could be successfully fractionated at 20-microns using a hydrocyclone. In hydrometallurgical tests about 80 pct of the phosphorus and alumina were chemically extracted from the slime using sulfuric acid. Limited bacteriological studies made of the slime showed that several types of microorganisms were present and grew in the material despite the presence of fluorine-bearing minerals.

Jan 1, 1963

By Harry R. Nicholls

A simple economical method has been developed for determining the in situ longitudinal and shear velocities in rock from which its elastic constants can be calculated. By detonating small charges of high explosives in shallow drill holes near a free surface, both longitudinal and shear waves were generated simultaneously. Accelerometers and velocity gages mounted to the rock surface were used to record the arrival time for both waves over travel path lengths from 50 to 450 feet, Measurements were made in two rock types. From the arrival time measurements, the longitudinal and shear wave velocities were calculated. From these velocities and the density of the rock, the elastic constants were calculated. The dynamic elastic constants of drill core samples of the two rock types were determined in the laboratory by the resonant-frequency method, The lab- oratory and in situ elastic constants are compared and significant differences noted. In general, there is less spread in the in situ data than in the laboratory data, and Poisson's ratio does not fall outside the theoretical limits for the in situ data as is often the case for laboratory-determined elastic constants.

Jan 1, 1961

By J. W. Hunter, J. H. Jacobs

"Approximately 355 tons of nodules from Chamberlain; S. D., ore were processed in the 1-ton-per-day electrolytic-manganese pilot plant of the Bureau of lanes at Boulder City, Nev., in a continuous 3-month operation. The ore, ground to minus 48-mesh, was found to be amenable to leaching with acid directly or after roasting under reducing conditions in a Skinner muffled multiple-hearth furnace.Unroasted ore gave an acid-leach extraction of 84 to 88 percent of the manganese, which after neutralization showed an over-all extraction of between 81 and 85 percent of the manganese. The amount of iron extracted varied, but it was always,enough to permit the use of ammonia for neutralization.Roasted ore showed an acid-leach extraction of 89 to 91 percent of the manganese. A large amount of iron went-into solution, so that it was not economical to neutralize it entirely with ammonia. By neutralizing with calcine to a pH of 5.0 and completing -neutralization with ammonia to a pH of a.5 an over-all manganese extraction of 84 to 86 percent was obtained. The slight increase in. extraction on roasted ore probably would not justify the cost of roasting.Acid consumption averaged 1.75 pounds per pound of manganese extracted. Settling rates of the residue in leach solution were to slow to permit clarification in thickeners, but a Moore vacuum leaf filter proved to be satisfactory. Purification of raw leach solution was .accomplished readily by hydrogen sulfide with a low gas consumption. Electrolysis was normal, without difficulty, and with -current efficiency ranging between 62 and 66 percent.The use of Chamberlain modules for the production of electrolytic manganese would result in an operating cost of 0.8316 cent per pound higher than the cost of producing electrolytic manganese from Three Wids ore."

Mar 1, 1946