Search Documents

By Kenneth L. Rubow, Virgil A. Marple

"INTRODUCTION Respirable dust is defined as the dust which penetrates to the alveolated regions of the lungs. Due to the size selective nature of the particle removal mechanisms in the nasal passages and lung airways, criteria defining respirable particles must be a function of the particle size. Three criteria defining respirable particle penetration are shown in Figure 1. These criteria have been defined by the British Medical Research Council (BMRC), the American Conference of Governmental Industrial Hygienists (ACGIH) and German TBF 50-11 (1).The quantity of respirable particles in an aerosol can be measured by use of two-stage samplers. The first stage consists of a particle preclassifier with penetration characteristics corresponding to one of the respirable penetration curves in Figure 1. The large nonrespirable dust particles are removed from the airstream in the preclassifier and the smaller respirable dust particles pass on to some device which can measure their concentration (the respirable dust concentration).Instrumentation for the measurement of respirable coal mine dust has been limited by the severe conditions existing within the coal mine. The conditions of particular importance are the methane atmosphere, high humidity, and the general non-laboratory type environment. The most severe of these conditions is the methane atmosphere since any electronic or electric powered instrumentation must be intrinsically safe to operate in such an atmosphere.In spite of the difficulty of sampling respirable dust within the mines, many instruments have been developed for in mine use. Although these instruments operate under a variety of principles they generally fall within two categories: personal samplers and area samplers.A personal sampler is worn by the mines while he is performing his duties in the mine. These devices are generally small, light weight and require little power so as not to interfere with the miner's ability to work."

Jan 1, 1988

By Paul C. Turner

The U.S. Bureau of Mines, through an Interagency Agreement with the U.S. Army Tank-Automotive Command (TACOM), has successfully developed a steel expendable pattern casting process (EPC) for the manufacture of armorplate. The new armor is lighter and more ballistically effective than conventional rolled homogeneous armor (RHA), and costs less. An applique armor spinoff from the program was field-tested during the Gulf War. The applique armor withstood direct impacts from enemy munitions without failure.

Jan 1, 2010

By R. R. Sayers

The effect of comparatively low concentrations of carbon monoxide for short periods and under normal air conditions.of temperature and humidity , with the subject at rest , was studied by Dr. Yandell Henderson and his co -workers . In making recommendations to the New York and New Jersey tunnel commissions * he advised that , if the New York New Jersey vehicular tunnel be so ventilated that persons passing through the tunnel would be exposed to not more than 4 parts of carbon monoxide in 10,000 parts of air for not longer than 45 minutes , they would experience no ill effects . supplementary experiments , carried out by us in connection with our studies at the Bureau of Mines experiment station at Pittsburgh, substantiated this advice . ** In continuing our studies on low concentrations of carbon monoxide , we made a few experiments in a gas chamber where the conditions could be accurately controlled . The factors investigatel were : ( 1 ) The effect of long exposure in low concentrations of carbon monoxide ; ( 2 ) The effect of strenuous exercise ; ( 3 ) The effect of high temperature and humidity in low concentrations of ccarbon Lonoxide .

Mar 1, 1922

By Alexander May

The U.S. Bureau of Mines conducted studies to determine if phosphate slag stockpiles at Tennessee Valley Authority's National Fertilizer Development Center were hazardous materials. The stockpiles were not hazardous materials as determined by Environmental Protection Agency (EPA) extraction procedure (EP) toxicity test. Radium-226 concentration was 28.7 pCi/g in slag and 2.1 pCi/g in background material. Radium-226 was not leached from the slag. Fluoride concentration was 3.87 pct in slag, 0.18 pct in subsurface material under slag, and 0.08 pct in the background. Slag material permeability was 1.65 x 10-3 cm/s, and subsurface material permeability was 3.24 x 10-6 cm/s. Rain water, trapped in a depression on top of the east slag stockpile, became seepage water at the base of the stockpile. Concentrations of EPA toxic elements in seepage water were much less than concentrations from an EPA EP toxicity test on the slag. Twelve elements-Na, Mg, Ca, Sr, Ba, Cr, Mn, Co, Cu, Cd, AI, and P-had higher concentrations in seepage water than in rain water on top of the slag stockpiles, or in creek water adjacent to stockpile bases, indicating that they were leached from slag stockpiles.

Jan 1, 1990

By R. A. Franks, G. F. Friel, J. C. Edwards, L. Yuan

Two mine-fire experiments were conducted in the National Institute for Occupational Safety and Health's (NIOSH) Safety Research Coal Mine (SRCM) at the Pittsburgh Research Laboratory (PRL) which demonstrated that smoke from diesel-fuel fires of 500 kW and 660 kW heat-release rates in a return airway can develop, without causing a complete air flow reversal, into a roof layer that can migrate upwind forming a counter flow to the primary airflow in a crosscut. Subsequently, smoke can penetrate into an intake airway and create a hazardous atmosphere in the intake airway upwind from the fire. Visibility conditions less than 13 m were created by the smoke in the intake airway downwind from the crosscut. Modeling of the event with a three-dimensional, time-dependent, computational fluid dynamics (CFD) program correctly represented the smoke movement.

By R. P. Bush

The U.S. Bureau of Mines performed Cu exchange capacity (CuEe) tests on Ca and Na mont-morillonites and attapulgite clays. Mathematical models were developed from the data that the CuEe's are derived from for each clay as a function of pH, Cu concentration, and the concentrations of metal ions, which compete with Cu for exchange sites. An analysis was made of the impact of competing ions on Cu losses due to ion exchange. The results show that the CuEC's of clays, and hence Cu losses, are decreased by the presence of competing ions, and that AI and Mg have the largest impact of those cat-ions normally present in Cu leaching solutions.

Jan 1, 2010

By F. A. Rutledge, B. S. Webber, J. M. Moss

"INTRODUCTION The United States, with its vast resources of relatively low-grade zinc been the world's leading producer of zinc -metal for many years. The expanded zinc production during the period, 1939-44, inclusive, was induced by favorable premium prices and has depleted the known ore reserves in the United States. The 1943-44 rate of zinc production cannot long be maintained in the United States, especially if premium prices are removed. Domestic zinc reserves, have been depleted to such an extent that it is doubtful if our mines will again be able to completely and continually fulfill the needs of this country.The Bureau of Mines, anticipating a postwar consumer demand for 550,000 to 750,000 tons of slab zinc and an additional 100,000 tons for use in paints and chemicals, sent two engineers to Sedanka Island in July 1945 to investi¬gate the deposits near Biorka Harbor.ACKNOWLEDGMENTIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion the Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director."

Nov 1, 1946

By Richard D. Miller

The helium resources base of the United States was estimated by the U.S. Bureau of Mines (Bureau) to be 894.6 Bcf as of January 1, 1989. These resources are divided into four categories in decreasing degree of assurance of their existence: (1) helium in storage and in proved natural gas reserves, 282.4 Bcf, (2) helium in probable natural gas resources, estimated at 237.7 Bcf, (3) helium in possible natural gas resources, estimated at 263.1 Bcf and (4) helium in speculative natural gas resources, estimated at 111.4 Bef. These helium resources are further divided into depleting and nondepleting, with the helium in storage being in a classification. The depleting resources are those associated with natural gasfields that are, or will be produced for the natural gas they contain. Almost all of the helium in potential (probable, possible and speculative) natural gas resources is included in this classification. These depleting resources are estimated to contain 775 Bcf of the total helium resource base. Helium resources contained in nondepleting natural gas resources, i.e., those in shut-in, abandoned, or otherwise nonproducing natural gas fields, are estimated to total 84 Bcf There is 35 Bcf of helium in storage in the Federal Government-owned Cliffside Gasfield near Amarillo, TX.

Jan 1, 1990

Determine the appropriate spacing and alarm levels for carbon monoxide and smoke sensors used for fire detection in underground coal mine conveyor belt entries. Background Fire represents one of the most severe hazards in underground coal mines. Early-warning fire detection in underground coal mines is essential to successfully implement and execute evacuation and control measures. Both carbon monoxide (CO) and smoke sensors have the ability to provide reliable early-warning capability, provided that they are spaced properly and set at the appropriate alarm levels. The U.S. Bureau of Mines conducted a series of large-scale experiments where a small coal fire was used to ignite a conveyor belt at air velocities of 0.76 to 6.1 m/s. The test configuration was purposely designed to model a worst-case fire scenario for fires that develop within conveyor belt entries in underground coal mines. During the tests, CO and smoke levels were continuously measured to determine alarm times and alarm levels as the fire intensity progressed. The data from these tests indicated that for a given sensor spacing, the time to reach a preset alarm threshold depends upon the belt entry air velocity and cross-sectional area. Analysis of this data resulted in the equations and nomographs for CO and smoke sensor spacing, and alarm levels contained in Bureau of Mines RI 9380, "Fire Detection for Conveyor Belt Entries."

Jan 1, 1993

By W. E. Dennis, M. M. Fine

"INTRODUCTION During peacetime, the United States uses less than 3,000 tons of chemical-grade celestite annually. The war need, however, was estimated to exceed 15,000 tons a year.Hitherto; most of the required chemical-grade ore has been imported from England, Mexico, and other foreign countries. If foreign sources do not find it possible to meet the demand for ore of chemical grade (plus 92 percent SrSO4), it is expected that requirements could be satisfied by concentrating low-grade domestic ores. Celestite deposits on Brown, Nolan, Fisher, and Coke Counties, Texas, are considered to be possible sources of supply for this low-grade material. The Bureau of Mines explored the most important deposits to determine the grade and amount of ore available and conducted ore-dressing tests to obtain a suitable method of concentration.The exploratory work, consisting of test pitting and sampling, was carried on under the direction of W. E. Dennis, one of the authors of this paper, from October 8, 1942, to January 30, 1943. The ore dressing-tests described herein were conducted at the Bureau of Mines Laboratory at Rolla Mo.In this report, a particular deposit is referred to by the name of the landowner on whose .property the .deposit lies. The location of the deposits investigated is shown on figures 1, 2, 3, and 4.The celestite deposits were previously studied by the Bureau of Economic Geology of the University of Texas, and the results of its investigation are published in Mineral Survey Circular No. 46."

Feb 1, 1947

By J. A. Organiscak

In the United States, respirable coal mine dust exposures are limited to a 2 mg/m3 time weighted average for a working shift. If the silica content of the sample exceeds 5 percent, the 2 mg/m3 standard is reduced according to 10- (% silica) to limit silica dust exposures to 100 µg/m3. Examinations of dust sampling data collected by the federal coal mine inspectorate showed that roof bolter occupations continue to be at risk for overexposure to respirable silica dust. Testing at the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health assessed the effectiveness of a canopy air curtain for controlling occupational exposures to respirable silica and coal dusts. Initial testing found that zones of higher velocity airflow shrank as distance beneath the canopy increased. This suggested that protection from occupational dust exposures would likely decrease as distance beneath the canopy increased. Further testing revealed that coal dust reduction efficiencies were most affected by changes in interference air velocity and, to a lesser extent, changes in canopy air quantity. However, respirable silica dust percentages under the canopy were not affected by such changes and, in fact, were not significantly different from silica percentages measured outside the canopy. This implied that the air curtain was equally effective on both respirable coal and respirable silica dust particles.

By Fred S. Karn

Inhibitors are used in coal mines as a precaution against accidental dust explosions. Although rock dust is the usual inhibitor many others have been tested. To facilitate testing a screening process using laser irradiation was proposed. The procedure includes irradiation of a coal-dust mixture followed by mass-spectrometric analysis of the evolved gases and an evaluation of the flammability characteristics of the gases. Carbonate-type inhibitors decreased the percentage of combustibles in the gases generated and inhibitors like NaCI (thermally stable salts) decreased the total gas generated. A suitable test procedure did not result from the investigation, demonstrating the inadequacy of fast heating, non-combustive techniques in rating inhibitors of coal dust explosions.

Jan 1, 1973

By C. F. Ellis

Interest in the composition of automobile exhaust gases has been greatly accelerated by recent studies that have indicated that these gases contribute to smog formation in urban areas. Several analytical methods have been published for the analysis of the hydrocarbons in the exhaust gases, but similar information has not been published on the analysis of the oxygenated compounds. This report presents procedures for chemical analyses of certain oxygenated compounds, procedures for sampling the exhaust gases for these analyses, and the analytical results of some experimental work in which these procedures were used. A stationary 1956 model, 170 horsepower, V-8, dynamometer-mounted engine, operated to simulate vehicular cruise conditions, was used for the study. Exhaust gases produced from a regular-grade Midcontinent gasoline during 15-40- , and 60-mile-per-hour cruise operations were analyzed by chemical methods for formaldehyde, total aldehydes, total carbonyls, total alcohols, carbon associated with the oxygenated compounds, and the oxides of nitrogen. Experimental results indicate: 1. The range of concentrations of the total of the functional groups of oxygenated compounds, expressed as moles per million moles of water-free exhaust gases, is about 90-100; the concentrations increase with engine speed. 2. Aldehydes comprise about 80-90 mole- percent of the total of the oxygenated groups, and formaldehyde accounts for about 50 mole-percent of the total aldehydes. 3. The order of magnitude of the concentration of the carbonyls is the same as that for the aldehydes, indicating that ketones are not a major group. A colorimetric test indicates that methyl ketones Constitute about 2 mole-percent of the oxygenated compounds.

Jan 1, 1961

By Perry N. Halstead

This report describes two goniometers that, by simple manipulation, can be used to ascertain the attitude of a joint, vein, or fracture plane observed on the planar projection of a borehole photograph taken with an NX borehole camera of the type developed by the U.S. Army Corps of Engineers. One goniometer was designed to interpret photographs taken in vertical drill holes and the other for photographs taken in inclined drill holes. In practice, several measurements are made on each photograph with the goniometer. These data are then substituted into mathematical equations, which are derived in this report and the attitudes of fracture planes are determined.

Jan 1, 1968

By J. L. Morning

During recent years, the Bureau of Mines has conducted an extensive investigation of the materials for making iron and steel. This work includes iron ore concentration, agglomeration, direct reduction of iron ores and concentrates, the production of pure manganese, chromium, and cobalt by electrolytic processes, the production of ferroalloys from low-grade domestic ores, and the development of special alloys to utilize these products. As a part of this general program, a Congressional appropriation allowed the con¬struction of an electric-furnace, semicommercial, ingot-producing plant at Shasta Dam near Redding, Calif. The primary objectives of the pilot plant were to determine the costs and operating problems involved in the production of steel and ferrous alloys in which sponge iron was used as melting stock, and to determine the physical properties of the materials produced. The pilot-plant equipment and the results of sponge iron-melting tests in the basic lined, electric arc furnace have been reported in previous publications.3/4/

Jan 1, 1953

By F. Fraas, H. H. Storch

"In the second paper 4 of this series, data were presented concerning the decomposi¬tion of polyhalite by saturated salt solutions. It was found that uncalcined polyhalite upon leaching with boiling saturated sodium chloride solutions yielded a brine in which the (K2 Mg) /304 ratio was considerably higher than that obtained from the calcined material, and for this reason appeared more suitable for the production of potassium chloride. It was found, in fact, that the leach liquors from uncalcined polyhalite deposited a mixture of KC1 and NaC1 upon evaporation and subsequent cooling, whereas those from calcined polyhalite yielded mixtures which contained not only potassium and sodium chlorides but also large quantities of glaserite, K3Na (S04)2. Hence it was decided to study the evaporation of the uncalcined poly—halite leach liquor and postpone experiments on the calcined polyhalite liquors until such time as a process for further removal of sulphate was developed.A considerable body of equilibrium data is available in the literature on thesystem K+ Mg++ — Na+ Cl—S04 =,— H20 for temperatures up to 83º C. Owing, however, tothe lack of data other than that corresponding to the invariant points and the complete absence of data for temperatures of 100 to 115°C., and owing to the fact that supersaturation phenomena render unsafe the prediction of the behavior of such a system upon evaporation, it was considered essential to obtain the necessary data by actual evaporation and analysis of the brines thus obtained."

Feb 1, 1931

By Richard Havens

A flotation procedure was devised by the Federal Bureau of Mines for beneficiating Mount Wheeler, Nev., beryllium ores that contain the beryllium minerals bertrandite and phenacite in a complex association with calcite, fluorspar, mica, quartz, and other accessory minerals, The method also has proven to be effective in trials on ore from the Lake George, Colo., area. Samples used in most of the research ranged from 0.49 to 0.73 percent BeO. Beryllium mineralization varied from two-thirds bertrandite to all phenacite. An unusually high grade sample containing 5 percent BeO as phenacite was floated on a batch basis to prepare concentrate for utilization studies. The beryllium minerals were floated from undeslimed pulps at natural pH using sodium fluoride and sodium hexametaphosphate (HMP), as modifiers, and a fatty acid-fuel oil combination as the collector. Key factors were the use of a minimum of about 4 pounds of sodium fluoride and between 2 and 4 pounds of HMP per ton of ore. Efficacy of the HMP was related to the grind, mineralogical composition, corollary reagents, and type and time of conditioning. Addition of the fluoride, HMP, and collector in that order, followed by appropriate conditioning after each addition, was essential for satisfactory flotation.

Jan 1, 1961

By John Ward Smith

The potential economic value of oil shale depends on the products from thermal degradation of the rock, because no other practical method for producing valuable material from oil shale has been found. Detailed study of thermal degradation behavior can aid in characterizing oil shales and their deposits and in evaluating oil-shale processing methods, Numerous publications describe various pyrolysis properties of oil shales (see surveys 3, 9, 11 and articles 1, 2, 4-8, 10, 12),4 but they do not describe a generally applicable analytical procedure for detailed evaluation of thermal degradation products. The analytical method presented here for such evaluations is designed to provide for: 1. Control of retorting conditions--temperature, heating, rate, reaction atmosphere--plus some control over retort pressure and carrier-gas flow, 2. Precise direct gravimetric measurement of the thermal degradation products--oil, water, gas, and spent charge (residue after thermal treatment of the charge). 3. Samples of all products. 4. Determination of the identities and amounts of gaseous compounds produced. 5. Elemental analysis and gross heating value of all products. 6. Determination of the distribution in the retorting products of the elements present in the original samples.

Jan 1, 1962

By Robert D. O'Brien

"INTRODUCTION The Miscellaneous Minerals Division of the War Production Board requested the Bureau of Mines to investigate the Gallatin corundum property as a possible source of corundum, which was in short supply due to the war. The Gallatin corundum property, also known as the ""Fuller mine"", the ""Montana Corundum mine"", and as the ""Old Qorundum mine"" was first examined by a Bureau of Mines engineer 2/ in July 1943. Bureau of Mines work on the property started October 11, 1943, was recessed May 5, 1944, and was resumed in October 1944 when the diamond-drilling program started. The project was completed February 7, 1945. The data obtained are given in this report.The Federal Geological Survey made a reconnaissance survey in the spring of 1943 and mapped the area the following autumn. The results of these surveys are contained in a memorandum report prepared in December 1943.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual investigative work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests."

Aug 1, 1947

By L. C. IlsLey

From time to time the Bureau of Mines has issued publications dealing with the various classes of explosion-proof mining machinery that have been tested and approved as permissible for use in mines having atmospheres that may become inflammable by reason of the inadvertent presence of gas or dust. These publications are confined almost entirely to description of the features contributing directly or indirectly to the prevention of explosion or shock hazards, and are intended to give inspectors, safety engineers, and others already familiar with the general safety requirements more detailed information on the safety features of the design of a particular machine. As a background for papers describing permissible machines and to avoid the necessity of duplicating descriptions of methods of conducting investigations and tests of such machinery, Bureau of Mines Bulletin 305, Inspection and Testing of Mine-Type Electrical Equipment for Permissibility, was pub¬lished in 1929. Three bulletins giving detailed descriptions of the three most numerous types of machines have been issued, viz., Bulletin 313, Permissible Storage-Battery Locomotive and Power Trucks. Bulletin 343, Permissible Coal-Handling Equipment. Bulletin 392, Permissible Coal-Cutting Equipment.

Jan 1, 1937