Search Documents

By Webster S. Anderson

Two series of tests were run with planer model 'BB": one at the Arickaree mine of the San Francisco Chemical Co., Rich County, Utah, and one at the Roslyn No. 9 mine of the Northern Pacific Railway Co., Roslyn, Wash. The tests at the Arickaree mine were started on June 25, 1958, and continued until September 30, 1958. Prior to these tests, an electrically activated remote-control system was installed, and other modifications were made on the planer. The tests showed that the planer in general and the remote-control system worked very well; however, the various cutting tools used would not consistently penetrate and cut the phosphate rock. This indicated that the cutterhead design had to be changed before the planer would operate efficiently in phosphate beds similar to the "A" bed in the Arickaree mine.

Jan 1, 1962

By W. J. Wenger

Oil fields in the Powder River Basin of Wyoming have produced 731 million barrels of petroleum through 1959. Production in 1959 was 32 million barrels, the highest production since 1924. The record production was in 1923, when the Basin produced 38 million barrels of oil and the Salt Creek field, then at its peak, produced 35 million barrels. In this report, the characteristics of crude oils found in the Basin are used as a basis for determining the best re-fining uses for the oils and for predicting the characteristics of oils that may be discovered in the Basin in the future. Analyses of 108 oils sampled over a period of 30 years are presented Crude oils of two major types are produced from the Powder River Basin. One has a low sulfur content and occurs in younger formations, and the other has a high sulfur content and occurs in older formations. The oils with low sulfur contents are generally light colored and waxy, and may be either paraffinic or naphthenic. The oils with high sulfur contents are usually dark colored and asphaltic; only their low boiling fractions are paraffinic. Alteration appears to account for the anomalous properties of some oils found at shallow depths. Shapes and slopes of correlation index curves classify the oils into the same two groups as their sulfur contents, with gently sloping curves representing the low-sulfur oils and steep curves representing high-sulfur, asphaltic oils,

Jan 1, 1961

By H. R. Appell

The Bureau of Mines studied the conversion of a variety of cellulosic wastes, for example, sawdust, bovine manure, sewage sludge, urban refuse (free of metal and ceramics), etc., to heavy oils. The objective of the investigation was to determine the scope of the reaction and elucidate the chemistry involved. The reactions took place in the presence of synthesis gas and water or carbon monoxide and water under conditions of elevated temperatures and pressures. Waste conversions above 90 pct, often near 99 pct, with oil yields in the range of 40 to 60 pct, were obtained in the temperature range of 250° to 425° C and pressure range of 1,500 to 4,000 psig. Because mild conditions were sought, most of the experiments were conducted at temperatures of 250° to 350° C and pressures of 1,500 to 3,000 psig. In general, lower viscosity products were obtained at higher reaction temperatures. Conversions and oil yields were significantly increased by operating in the presence of a high-boiling oil; either anthracene oil or oil recycled from the process was satisfactory. Synthesis gas containing 50 pct carbon monoxide gave satisfactory results as a replacement for carbon monoxide. Cobalt molybdate on alumina catalyst, used with sodium carbonate, gave a product of lower viscosity and lower oxygen content than sodium carbonate used as the sole catalyst. The waste-to-oil process has been successfully investigated in continuous flow equipment as well as in batch autoclaves.

Jan 1, 1975

By Sara J. Davenport

With the increased demand for mercury incident to preparations for national defense and the reduction in imports from some of the usual sources owing to war conditions, many small mines in the United States Pure now being worked that ordinarily would be unprofitable. This is indicated by the following table on mercury produced in the Unite States in 1939-40 (1)4/

Jan 1, 1941

By J. S. Stachulak, G. H. Schnakenberg

The objective of the Diesel Emissions Evaluation Program (DEEP)-sponsored project at Inco's Stobie mine was to conduct a long term field evaluation of diesel particulate filter (DPF) systems available to the underground mining industry. Some of the major issues studied were criteria for selecting the filter media, means of DPF regeneration, efficiency of DPF systems and the occurrence of unwanted secondary emissions, and reliability and durability of DPF systems. Nine state-of-the-art diesel particulate matter (DPM) filtration systems have been retrofitted to heavy-duty and light-duty vehicles and have been subjected to extensive long-term in-mine evaluation. Periodic efficiency tests were conducted at various stages of the study (2001, 2002 and 2004) to establish in-use efficiencies and durability of the tested DPF systems. The results were used to assess the effects of the filter systems on the concentrations of particulate matter, nitric oxide, nitrogen dioxide and carbon monoxide in the vehicle exhaust. The variety of filtration systems and regeneration concepts used in this study offered the opportunity to investigate their advantages and disadvantages. This paper also offers a review of selected experiences with the installation and operation of the DPF systems on underground mining vehicles at the Inco Stobie Mine.

By C. I. Pierce

Knowledge of the water content of oil-bearing formations is important in petroleum-reservoir evaluation work. Electric logging provides a means for making reliable estimates of water content if resistivity-saturation relationships representative of the formations are available. Relationships can be determined in the laboratory by a number of methods. This report describes and presents results of a laboratory investigation conducted at the Bureau of Mines Appalachian Experiment Station, Morgantown, W. Va. (1) to evaluate an evaporation method of attaining water saturations in sandstone samples when determining resistivity-saturation relationships and (2) to compare saturation exponents derived from data obtained, using different methods of achieving water saturations. A series of tests was conducted to determine the effect of evaporation on salinity distribution within the core specimen. Results of these tests show that a zone of high salinity was set up at the surface of a sample during evaporation and that long periods were required for the sample to reach resistance equilibrium after evaporation had ceased. Equilibrium time ranged from several minutes to several days, depending on the sample size and the technique used. The high-salinity zone was removed from the sample by using auxiliary porous material in capillary contact with the sample surface during evaporation. Salinity determinations and resistance measurements indicate that, at saturations greater than the minimum interstitial values, the mechanism of flow during evaporation was one of moisture migration mainly as a liquid from the interior of the test specimens to their exterior surfaces. The concentration of the contained brine remained essentially unchanged, except for a narrow zone near the evaporating surfaces.

Jan 1, 1958

By G. W. Jones

Among its investigations into the prevention of waste in production and use of oil and gas, the Bureau of dines has made considerable study of the efficient utilization of gasoline and by-product distillates in motors, this being done chiefly by measuring and analyzing the exhaust gases therefrom. A number of reports3 of a highly practical nature have been published and are available on this subject. The results of these tests have shown that the average motor vehicle wastes approximately 30 per cent of the heat value of the fuel used, as incomplete combustion products - carbon monoxide, hydrogen, and methane, These unnecessary large heat losses are mainly due to improper carburetor adjustment, and by proper¬ly adjusting the carburetors for maximum power and efficiency a large part of this heat loss can be eliminated. This in turn results in an increased mileage per gallon of fuel used.4

Jan 1, 1924

This Part describes a mine pager phone to public telephone interconnect sys tem that permits mine paging telephones to be selectively interconnected with the public telephone system, as illustrated by Figure 1. This interconnect concept was first conceived and demonstrated in breadboard form by H. E. Parkinson of Industrial Hazards and Communications, PMSRC, as one means for providing improved emergency and off-hours communications. The third-generation prototype unit described in this Part was designed and fabricated by Arthur D. Little, Inc. This unit is a small desk-top or wall-mounted unit that connects directly to both the public telephone line and the mine pager phone line, and requires no modifications to either the public dial telephone or mine pager phones. As part of this task, ADL also built, under a very compressed time schedule, a second-generation prototype unit suitable for reliable demonstration of the interconnect concept during the Bureau's technology transfer seminar on mine communications in March 1973. * A major objective of the design of the third-generation unit described in this Part was that it be compatible with present mine pager phone systems utilizing DC voltage on the mine phone line to activate the phone loudspeakers. Therefore, this unit was designed to operate in a push- to-talk, push-to-listen mode that accommodates the inherent design differences and operation modes of the mine phones of different manufacturers. Though this push- to- talk, push- to-listen mode of operation may seem slightly unusual at first sight, we have found it is easily learned by new users. However, mine phone manufacturers wishing to expand their product lines with such an interconnect system will probably find it to their advantage to customize the design of this system to their particular mine phones, thereby utilizing the unique attributes offered by their individual product lines. This customization should not be difficult, and Section III below suggests some of the features that can be easily added to future designs. Detailed parts lists and circuit schematics for the present third-generation proto- type system can be obtained from the system manual submitted to PMSRC and placed on public file.

Jan 1, 1974

By David Garry, Michael J. Brnich, Lynn L. Rethi, Henry P. Cole, William J. Wiehagen, Roberta A. Calhoun

This document contains most of the materials needed to use the exercise. The main part of the document is the instructor's copy. It tells how to use the exercise, presents the objectives, the master answer sheet, the scoring key, and discussion notes to be used following the exercise. The next section summarizes results from field tests of the exercise, and reports the miners' evaluation of the activity. The last part of this document is three appendices. Appendix A is the exercise problem booklet. This booklet can be duplicated locally. The booklets are reusable. One is needed for every person in the classroom. Appendix B is the answer sheet and the trainee's questionnaire. Copies of this answer sheet must have the latent image (invisible) ink answers that appear in Appendix C printed on them.1 Answer sheets are consumable. One is needed for each person or each small group of persons who work the exercise. Exercise Summary Read this section first. It determines if the exercise is appropriate for your classes. If you choose to use the exercise, examine the table of contents and review the remainder of this document. Type: Latent image Audience: Supervisors, Safety Personnel and Accident Investigators Length: Eight questions (30 minutes for administration plus 30 for discussion) Skills: Developing a strategy or plan to prevent slips and falls Following correct procedures in conducting an accident investigation Preventing unsafe work practices Recognizing and instituting hazard controls in the section Identifying and implementing safe work procedures Location: Underground coal mine section Problem: You have been the general mine foreman at White Rock Mine for 4 years and have worked at this mine for 12 years. The mine superintendent calls you into his office. He gives you an accident report of an employee in 4-G section who was injured while carrying rock dust bags from the rock dust car to a battery powered scoop. It is several days after the accident and the mine superintendent assigns you and the safety supervisor to thoroughly investigate the accident to determine all the contributing factors. Your job is to make specific recommendations to prevent future slipping/tripping accidents.

Jan 10, 1999

By C. P. Fang

"For lower stages of multinozzle micro-orifice impactors, as many as two thousand nozzles are uniformly arranged within a cluster diameter of 1.06 inches. In the impaction region the mass flowrate of the spent air increases along the radius and reaches a maximum at the periphery. This crossflow can significantly deflect the air jets of the outer nozzles, hence the characteristics of impaction changes.Investigators in heat transfer and fluid mechanics have studied the influence of crossflow on jet deflection and found the dimensionless deflection of the jet centerline X/Dn is a function of (S/Dn)(l/m) . only, here X is downstream coordinate measured from the center of the jet orifice, Sis the jet-to-plate distance, Dn is the orifice diameter and m is the jet/crossflow mass flux ratio defined as:"

Jan 1, 1989

By R. E. Head

"The microscopic work described below was engaged in primarily into ascertain the approximate proportions in which the copper sulphides existed in the ore examined, and by a comparison of the results obtained from a study of both head are tailing samples to supply data which might be of value in treating the ore by flotation. Incidentally, the physical characteristics and association of the sulphides were noted in order to determine the possible relation or bearing of these features on the present conditions of treatment. Since the copper in the ore occurred as three distinct sulphide minerals - chalcopyrite, chalcocite, and bornite each containing copper in different proportions, there appeared to be little or no possibility of obtaining the desired information by chemical methods of determination.Type of material examinedThe material examined was in the crushed condition and was said to be representative of the flotation feed or heads and the resulting tailing. No hand samples of the ore were examined nor any account taken of the physical condition and association of the minerals in place, because the possible value of the analytical results depended on conditions as they existed in the crushed ore. As the problems under consideration dealt only with the sulphide minerals, especially those of copper, the products from screen sizing were concentrated by hand panning and the gangue discarded. The concentrate obtained consisted almost entirely of the sulphide minerals, since the panning had been very carefully done. The object of this procedure was to obtain a sufficient quantity of high-grade sulphide material, from the sample of each screen size selected for examination, to permit its being so prepared for examination as to be representative of the physical characteristics exhibited by a large number of sulphide grains from each respective size, In the tests and investigations carried on by the company' treating the ore the following sizes had been used in tabulating data and basing conclusions:+48, +65, +100, +150, +200, and -200. These same sizes were used in the microscopic investigation, since the results obtained thereby could be most readily utilized for comparison with the results obtained in previous experimental work, together with deductions based on actual concentration of the ore on a commercial scale."

Jun 1, 1921

By A. J. Kraemer

For a number of years the Bureau of Mines has conducted semi-annual survey to determine the changes in the characteristics of the rotor gasoline being sold in the United States. Certain cities have been decided upon as points of origin of samples. Tare choice of these cities has been governed by their situation as the representative of a more or less definitely bounded marketing territory. Samples have been taken on or about the fifteenth day of January and July of each year. In the collection of the samples an attempt has been made to get a representation of the important types of motor fuel being sold, and also to tame into consideration the proportion of tie total consumption that is supplied by the different marketers. It is therefore felt that the survey affords a reliable indication of the quality of the gasoline being sold throughout the United States at the time of sampling. The figures in Table I, below, were obtained by averaging the end points of the least volatile and most volatile samples of gasoline. For example, of 850 samples analyzed in 1919, the 10 per cent (85 samples) having the highest end points, and the 1C per cent having the lowest end points were averaged. These averages are represented in the table as the "Maximum 10 per cent" and the "Minimum 10 per cent", respectively. The same scheme was used in the succeeding surveys.

Jan 1, 1925

By John W. Cole

The Bureau of Mines conducted a trenching and sampling project during 1947 on the tungsten-rich granodiorite that outcrops in Henderson Gulch, Montana. During the course of this investigation, interest was attracted to the Sunrise copper-gold mine in metamorphosed limestone in the north slope of the gulch. The mine was examined by S. H. Lorain, Chief, Mining Division, Albany Branch, in May 1948. A trenching and drilling program was recommended to develop a parallel vein indicated by outcrops to lie below the principal productive Queen vein. In the meantime, the Queen Mining Syndicate initiated a trenching program that exposed high-grade lead-copper-silver-gold ore in a nearly vertical vein that strikes N. 600 E. to east. A core-drilling program to develop this vein was initiated in September 1948. This report presents the factual data obtained from the trenching and drilling operations. The Sunrise mine was discovered about 1890. Production has been estimated to be $120,000 in gold from 40,000 tons of ore mined during the period 1892-1903. The tailing from this operation was treated by cyanidation in 1912, with a reported recovery of $3.50 to $4.00 a ton from 15,000 tons of material. Subsequent production of sulfide ore was 7,396 tons treated by smelting, with recovery of 1,569.42 ounces of gold, 10,003 ounces of silver, 352,899 pounds of copper, and 354 pounds of lead.

Jan 1, 1950

By H. D. Kline

This publication describes mining and milling methods and costs at the Madison mine of National Lead Co., St. Louis Smelting & Refining Division, in the Fredericktown district of southeast Missouri and is one of a series prepared by the Federal Bureau of Mines on methods, practices, and costs of mining and milling throughout the United States. The are bodies of the Madison mine are known for the complexity and diversity of their are minerals. Sulfides of copper, nickel, and cobalt occur in commercial quantities with lead sulfide, which is the most valuable metallic mineral in are bodies of the Bonne Terre formation in southeast Missouri. Several attempts were made by various operators to mine the complex ores and separate the sulfide minerals before 1927 when National Lead Co. became interested in the Fredericktown district. Operating then as the St. Louis Smelting & Refining Co., the company began mining and milling ores from the Madison mine in 1944 and has operated continuously since then. A recently built refinery produces copper, nickel, and cobalt metal from a concentrate containing iron sulphides and small quantities of copper, nickel, and cobalt sulphides.

Jan 1, 1961

By B. H. Clemmons

A field method has been devised for rapid determination of heavy minerals occurring in the unconsolidatod beach and dune sands. The method has been proved practical by usage in field evaluations of several hundred beach- and dune-sand samples in the Florida area. The simple equipment required and the techniques involved are described. Other data show that the method is relatively insensitive to variations in the mineralogical content or size distribution of the mixed heavy minerals contained in the samples tested. A modification of this procedure, found to be suitable for plant use in determining the relative purity of heavy-mineral flotation concentrates, is also described. A specific application is determination of the amount of feldspar-quartz in spodumene flotation concentrates. The results of the rapid evaluation techniques closely approximate those obtained by more precise laboratory procedures.

Jan 1, 1957

By John C. Franklin

Water-based epoxy sealants were examined during a 2-year period to deter-mine their effectiveness as barriers to radon release in uranium mines. Radon emanation rates from uranium ore samples were monitored for extended periods in the laboratory before and after sealant application. Reduction of radon flux due to the coating of laboratory samples was approximately 80 percent. Test chambers in a dormant uranium mine were monitored to determine both short and long-term barrier effectiveness. These field studies of the seal-ants indicated radon flux reductions exceeding 50 percent relatively soon after application and nearly 75 percent about 1 year later. An unexpected complication to early monitoring in the form of a large radon emanation increase, believed due to added moisture, is discussed.

Jan 1, 1977

By Donald O. Capstick

[ ]

Jan 1, 1983

By J. Douglas Causey

In 1987, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied 13,374 acres of the 14,994-acre Ireteba Peaks Wilderness Study Area (NV-050-438) in order to evaluate its identified mineral resources. The study area is located in Clark County, NV, about 4 miles south of Nelson, NV. No identified resources were found within the Ireteba Peaks study area, although there are identified subeconomic resources just outside of the study area boundary. Most of the area is underlain by Tertiary granitic rocks, which apparently postdate mineralization. The area is virtually surrounded by mining districts with mines developed in older rock units. On the north side, quartz monzonite, volcanic tuff, and tuffaceous sediments in the Eldorado mining district host deposits of gold, silver, copper, zinc, and mercury. On the south side, Precambrian gneiss, intrusive andesite porphyry, and hornfels in contact with Quartz monzonite in the Searchlight mining district host gold, silver, copper, and lead deposits. The Newberry mining district to the southeast had copper, gold, and silver mineralization in Precambrian gneiss and andesite.

Jan 1, 1988

By R. F. Waters

Laboratory-scale selective volatilization methods developed by the Bureau of Mines to recover germanium and gallium concentrates from coal fly ash and phosphorus furnace flue dust are summarized. In the better experiments between 85 and 98 percent of the germanium was recovered as the lower oxide and as sulfides, and between 75 and 97 percent of the gallium was recovered as the lower oxide and as the trichloride. Grades of the condensates were inconsistent and varied between a few tenths of a percent and 8 percent, depending on the method used. In the primary extractions of germanium alone the degree of enrichment surpassed 100 to 1, and for gallium the best ratio was 30 to 1. Upgrading of condensates by vaporization retreatment and by leaching and precipitation is discussed. An appreciable degree of mechanical preconcentration by attrition scrubbing and elutriation was possible on two fly ash samples.

Jan 1, 1967

By S. M. Runke

The pegmatite investigations at the Rapid City, S. Dak., Experiment Station during; the pact 3 years have been primarily a study of recovering beryl from nonlithium-bearing pegmatite rock by continuous-testing methods. Beryl concentrates containing 25 to 88 percent beryl were produced from rock that ranged in beryl content from 0.1 to 2.5 percent. The beryl recovery ranged upward from 70 percent but averaged better than 80 percent. Although promising results have been obtained with flotation methods for upgrading these concentrates to standard specifications, additional work is needed to improve and simplify the procedure. In addition, it was demonstrated that several potentially useful coproducts could also be recovered from pegmatite rock. The principal coproducts were mica, feldspar, and quartz. A heavy-mineral product also was made from pegmatites containing tin, tantalum, and columbium. The recovery if these minerals in products meeting the specifications of the commercial users has been reserved for future study. The investigations also included studies on extraction of beryllium from both high-grade beryl and flotation concentrates of medium beryllium content. The procedure investigated consisted of sintering beryl or beryl flotation concentrates with limestone, acid curing the resulting sinter with sulfuric acid to dissolve the beryllium, and water leaching to extract the beryllium. Over 90 percent of the beryllium was extracted by this procedure. Most of the optimum conditions and quantities of reagents were determined for dissolving the beryllium. As aluminum and iron also were taken into solution by the acid, further research is needed on methods of recovering high-grade beryllium salts from the solutions containing these elements.

Jan 1, 1957