Search Documents

By A. F. Colombo, R. T. Sorensen, D. W. Frommer

The Bureau of Mines developed a flotation method for concentrating spiral tailing produced from pilot plant tests on the Champion mine ore fines . The feed material contained about 49 percent Fe and 15 percent SiO2 and was posed mostly of specular hematite , muscovite , and chlorite . Bench- scale , batch flotation research developed a reagent suite composed of tall oil - fatty acid , fuel oil , sulfuric acid , sodium fluoride , and sodium silicate for recovery of iron minerals in the froth product . Concentrate made with the reagent suite contained 87.3 percent of the iron and analyzed 65.6 percent Fe and 1.9 percent SiO2 . Continuous flotation tests were made with a nominal feed rate of 400 lb /hr , but without middling recirculation . Using nearly the same amount and complement of reagents as in the batch tests , three similar continuous tests gave concentrates averaging 63.9 percent Fe and 3.1 percent Sio while recovering about 86 percent of the iron .

Jan 1, 1964

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigation beginning with No. 4251, of which this is the thirteenth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is followed by a description of each deposit developed in that half township. The 14 half-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project, except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on figure 13 in volume 1. The description of the deposits developed is followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated and a table for each half township is given with the discussion covering that area.

Jan 1, 1948

By R. V. Ramani, A. S. C. Owili-eger

A mass balance equation can be written for the unit block of Figure 7 for changes within the volume during time At as: [ ] where x and y are the coordinates; q is the flow across any surface; p is the density of the fluid flowing through the medium; qvol is the volumetric flowrate; @ is the medium porosity; and Ax and Ay are the dimensions of the block. The subscripts t and (t+At) denote time levels and At is the change in time. Writing this equation in nota- tional form and on rearranging, the following expression is obtained:

Jan 1, 1974

By Harold L. Rhodes

The Bureau of Mines has developed a method for determining the H2S content in natural gas samples. A gas chromatograph with a flame photometric detector was used to analyze samples with H2S concentrations ranging from 5,000 ppm to a minimum detectable limit of 0.01 ppm. A mass spectrometer was used to analyze samples containing H2S in amounts greater than 5,000 ppm. Methods are presented for preparing containers for H2S samples and for preparing standards using partial pressure and weighed standard methods, Sample collection techniques are discussed, as are analytical results which illustrate the loss of H2S while in the sample container and provide a basis for evaluating containers used for sampling and standard preparation.

Jan 1, 1979

By R. F. Waters

Laboratory-scale selective volatilization methods developed by the Bureau of Mines to recover germanium and gallium concentrates from coal fly ash and phosphorus furnace flue dust are summarized. In the better experiments between 85 and 98 percent of the germanium was recovered as the lower oxide and as sulfides, and between 75 and 97 percent of the gallium was recovered as the lower oxide and as the trichloride. Grades of the condensates were inconsistent and varied between a few tenths of a percent and 8 percent, depending on the method used. In the primary extractions of germanium alone the degree of enrichment surpassed 100 to 1, and for gallium the best ratio was 30 to 1. Upgrading of condensates by vaporization retreatment and by leaching and precipitation is discussed. An appreciable degree of mechanical preconcentration by attrition scrubbing and elutriation was possible on two fly ash samples.

Jan 1, 1967

By Richard A. Dick

Eight blasts were fired in a 2-1/2-ft bench in the Stewartville member of the Galena Limestone formation in an aggregate quarry near Stewartville, Minn. The shots were dimensionally proportional to production-size bench blasts and were about 5 to 10 percent of full scale. The effects of site, timing of initiation, and burden-to-spacing ratio were studied in a 2 x 2 x 2 factorial experiment, using three boreholes, caw;, containing a 1/2-in charge diameter of high-density ammonia dynamite, in each blast. Detonation velocity measurements indicated that the dynamite detonated satisfactorily in the 1/2-in charge diameter. The effects of the three experimental variables were analyzed by weight for the percentage of oversized material produced and for size distributions determined by screening the entire muckpiles. The bench faces were painted before each shot in an effort to determine the origin of the oversized material. The square pattern (burden and spacing = 15 in) produced finer overall fragmentation and less oversized material than the rectangular pattern (burden = 15 in; spacing = 22-1/2 in). Sites 1 and 2 were about ft apart. Although site 2 produced slightly better overall fragmentation than site 1, the amounts of oversized material produced showed no significant difference. The timing of initiation (instantaneous or delayed) did not significantly influence the overall fragmentation or the amount of oversized material produced.

Jan 1, 1973

By S. M. Runke

The pegmatite investigations at the Rapid City, S. Dak., Experiment Station during; the pact 3 years have been primarily a study of recovering beryl from nonlithium-bearing pegmatite rock by continuous-testing methods. Beryl concentrates containing 25 to 88 percent beryl were produced from rock that ranged in beryl content from 0.1 to 2.5 percent. The beryl recovery ranged upward from 70 percent but averaged better than 80 percent. Although promising results have been obtained with flotation methods for upgrading these concentrates to standard specifications, additional work is needed to improve and simplify the procedure. In addition, it was demonstrated that several potentially useful coproducts could also be recovered from pegmatite rock. The principal coproducts were mica, feldspar, and quartz. A heavy-mineral product also was made from pegmatites containing tin, tantalum, and columbium. The recovery if these minerals in products meeting the specifications of the commercial users has been reserved for future study. The investigations also included studies on extraction of beryllium from both high-grade beryl and flotation concentrates of medium beryllium content. The procedure investigated consisted of sintering beryl or beryl flotation concentrates with limestone, acid curing the resulting sinter with sulfuric acid to dissolve the beryllium, and water leaching to extract the beryllium. Over 90 percent of the beryllium was extracted by this procedure. Most of the optimum conditions and quantities of reagents were determined for dissolving the beryllium. As aluminum and iron also were taken into solution by the acid, further research is needed on methods of recovering high-grade beryllium salts from the solutions containing these elements.

Jan 1, 1957

By C. W. Smith

The U.S. Bureau of Mines conducted research to determine the effect of ground water control on the dewatering of phosphatic clay wastes. Two storage impoundments were constructed. One impoundment was surrounded on three sides with a series of well points (shallow vertical wells) to lower the ambient water table and the second impoundment served as a control. Ground water was pumped from the area surrounding the test impoundment for a period of 490 days. A constant pumping rate of 60 gal/min resulted in a water table drawdown of 13 ft, approximating the bottom of the impoundment. At the end of the test period percent solids in the test impoundment was 35 pct, while in the control impoundment percent solids was only 26.8 pct. Percent solids of greater than 30 pct is required for capping and final reclamation using fertile overburden.

Jan 1, 1989

By Wallace W. Roepke

Research to evaluate the lubricity effects achieved by spraying water on the cutting bit of a mining machine or spraying water on the coal during cutting has shown that neither practice affects cutting forces, as had been believed. However, when water was supplied to the cutting zone axially through the bit at 3,000 to 5,000 psi pressure, tangent'ial cutting forces were reduced an average of 30 pct at a I-in depth of cut while normal bit forces were reduced an average of 65 pct. Lower normal forces mean reduced bit wear, faster advance with greater depth of cut, and fewer coal fines.

Jan 1, 1985

By Berk. A. A.

"INTRODUCTION Corrosion of sections of piping used in steam-heating systems is frequently regarded as unavoidable, and periodic replacement is provided. Surfaces exposed to newly condensed steam appear to be especially vulnerable to attack. As an added nuisance, solid products of the corrosion tend to accumulate, plugging return lines.The trouble is ascribed in the main to carbon dioxide and oxygen 3/ 4 / 5/ 6/ dissolved in the condensate. When oxygen is the principal factor, the corrosion usually is characterized by pitting. Carbon dioxide tend3 to cause an acidic condensate which dissolves the metal more uniformly and produces the familiar failure at threaded areas where the piping is relatively thin, and where high stress may tend to acceletate the attack. Carbon dioxide enters the system with the feedwater, generally in a combined form such as carbonates and bicarbonates. Oxygen enters both with the raw feedwater-and as air leaking into lines under partial vacuum. The larger central-heating plants have sought to reduce corrosion by eliminating these gases as much as possible. A smaller plant ordinarily lacks the equipment and technical supervision required for this purpose."

Jun 1, 1944

By Victor Kalcevic

A gas-flow retort for thermal processing of oil shale to recover shale oil was developed by the Bureau of Mines at its Oil-Shale Demonstration Plant, Rifle, Colo., from 1948 to 1952. The retort is a crossflow gas-to-broken-solids heat exchanger. The heating medium is the gas produced in the shale retorting process. The gas is heated in specially designed stoves outside the retort and recycled to the retort. Oil shale from the Mahogany ledge section of the Green River formation in northwestern Colorado was the material processed. Indicated maximum oil recoveries for 20-to 25-gallon-per-ton shale in a l2-inch-thick shale bed and a 20-inch bed are 96 and 91 weight-percent of Fischer assay, respectively. Heat requirements for maximum recovery are 600 to 750 B.t.u. per pound of shale. Properties of the recovered shale oil are affected slightly by shale-bed thickness and extent of retorting. Oil recovery from oil shales assaying over 30 gallons per ton is lower than that from leaner shales.

Jan 1, 1959

By Richard A. Winters

In 1987, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 334-acre Mountain Lakes Wilderness Study Area (OR-011-001) in order to evaluate its identified mineral resources. The study area is located in Klamath County about 15 miles northwest of Klamath Falls, Oregon, and is adjacent to the Mountain Lakes Wilderness. The area is underlain by Pliocene-age basaltic andesite. No mining districts are in the study area nor were any claims recorded or found. There are no oil and gas lease applications. There are no identified mineral resources in the study area. INTRODUCTION This report describes the USBM (U.S. Bureau of Mines) portion of a cooperative study with the USGS (U.S. Geological Survey) to evaluate mineral resources and potential of the Mountain Lakes WSA (Wilderness Study Area), at the request of the BLM (U.S. Bureau of Land Management). The USBM examines individual mines, prospects, claims, and mineralized zones, and evaluates identified mineral and energy resources. The USGS evaluates potential for undiscovered resources based on areal geological, geochemical, and geophysical surveys. Results of the investigations will be used to help determine the suitability of the WSA for inclusion into the National Wilderness Preservation System. Although the immediate goal of this and other USBM mineral surveys is to provide data for the President, Congress, government agencies, and the public for land-use decisions, the long-term objective is to ensure the Nation has an adequate and dependable supply of minerals at reasonable cost.

Jan 1, 1988

By D. Hinton, M. McCawley, R. C. Lantz, F. Pisano, C. Stanley

"INTRODUCTION Aerosols (5 um have not been shown to be consistently generated and characterized in inhalation chambers. Particle deposition in the lungs however may occur with particles as large as 25 um(1). Therefore, in order to closely simulate the atmosphere of an underground coal mine where the distribution is bimodal, with modes at S and 15 um (2), particles much greater than <1 um must be characterized for uniform mixing and size distribution within these chambers. The Hazelton Animal Exposure Chamber has been chosen because it has been best characterized for smaller particles (<1 um) (3), and is the major type used by most inhalation toxicology institutes such as Lovelace Inhalation Toxicology Institute and Battelle Northwest Laboratory.BACKGROUNDPreviously published studies on the inhalation of solid aerosols have attempted to characterize the distrition of particles of <2 um in diameter. There are no published reports of extensive work characterizing either the size distribution of particles <1 um or the concentration throughout the exposure chamber (Table 1).Table 1 shows the variability and sizes of several aerosols <1 um in diameter used in five previous chamber studies.Discussion of Previous StudiesThe study done by Bauermash, Bryan, Dickinson, and Burke (4)stated two major concerns in the development of the 6.5 ft. diameter chamber. The first was that a quantity of animals could be exposed to the same concentration regardless of the location of the animal, and second was that the chamber could be easily cleaned and decontaminated. The solution to the first concern required a circular chamber with the contamination air entering the chamber somewhere along the central axis. The animals could then be changed during exposure time so that each animal was exposed throughout the total volume."

Jun 1, 1988

By H. M. Lawrence

"The land-pebble district, the larger of the two producing areas of Florida, is situated in Polk County and in the eastern part of Hillsborough County. About 80 per cent at the phosphate rock produced in the United States in recent years has been mined from this area. The phosphate ores, locally termed matrix. are beds of sands and clays containing the phosphate pebbles, considered to be Pliocene in age, derived by marine action from underlying Miocene phosphatic marls, and are covered by practically barren sands and clays that have been deposited more recently. Open-pit mining is practiced; hydraulic mining, which has been intensively developed in this district, is used exclusively for mining the matrix and, by some companies for removing the overburden, although drag-line excavators have become established and are proving economical for stripping operations. From the pits the matrix is pumped to adjacent washing plants for beneficiation. The product of the washers. after drying, enters the world markets as Florida pebble phosphate.In this district recovery of the phosphate pebbles by the washing plants has not been particularly effective in the past. The screening, designed to effect a seperation at about 20 mesh (0.033 inches), has not been well controlled. Washer rejects discarded to the waste dumps have contained appreciable amounts of material analyzing above the minimum commercial grade - 66 per cent B.P.L. (bone phosphate of lime). Such losses of commercial fractions should be considered avoidable, and have been discussed at length in a previous paper.3"

Jul 1, 1930

By R. D. Leitch

Tests have recently been conducted by the Bureau of wines on the ignition hazard of exposing heated filaments of electric mine lam bulbs in an explosive mixture of methane and air. This investigation was undertaken in order to settle a question that had arisen in connection with the safety of miners? electric lamps. For several years, in view of former studies made by the Bureau and reported in Bulletin 524, the fact that the heated filaments of even low voltage, lour candlepower bulbs constitute a danger was generally accepted by the Bureau&apos;s engineers. These early tests, as well as subsequent tests, were conducted with Pittsburgh natural was as the testing medium.

Jan 1, 1925

By P. M. Sullivan

The principles and application of amalgam electrolysis to the recovery of zinc and tin from secondary products were studied; this Bureau of Mines project was one phase of investigating the development of more efficient methods for processing iron-bearing zinc and tin to produce both base metals of high purity. Zinc of 99-99-percent purity was recovered from galvanizer&apos;s dross with recovery efficiency of 98 percent. Tin of 99.9-to 99.99-percent purity was recovered from hardhead with recovery efficiency of 81 percent. Both materials were treated by the same method in separate systems. Mercury was used to leach zinc from dross and tin from hardhead to form amalgams of each metal, both of which were subsequently refined electrolytically to produce high-purity metal. Impurities that were contained in both secondary products behaved as theoretically predicted; impurities that were insoluble in mercury remained as sludge in the leaching column. Except for lead, the readily amalgamated impurities were prevented from fouling the electrolyte by the blocking action of the amalgam electrode. Lead impurity in the tin-refining system dissolved and immediately precipitated as the sulfate. The primary advantage of the amalgam refining method lies in direct recovery of the extremely pure base metal from highly contaminated secondary material.

Jan 1, 1961

By B. D. Nash

The object of this research was to investigate the technical feasibility of preparing chromium metal by the thermal decomposition of bisbenzene chromium. Bisbenzene chromium, a pi-bonded sandwich type organometallic compound, was thermally decomposed under reduced pressure to form a metal plate on a heated substrate. Metal recovery was close to 100 percent of theoretical, with deposition rates up to 20.8 mg/hr/cm2. Metal purity was dependent not only upon the purity of the starting material, but also upon the sublimation rate of bisbenzene chromium. Total detectable metallic impurities ranged from a low of 18 ppm to several hundred ppm. In general, metallic impurities were less than 100 ppm. Carbon, the major nonmetallic impurity, ranged from less than 0.3 percent to more than 10 percent. The carbon contamination is most likely a result of the decomposition of the organic portion of bisbenzene chromium. An unusual property of some of the deposits was their outstanding corrosion resistance. Unlike pure electrolytic chromium, which dissolves readily, these deposits were insoluble in hot mineral acids.

Jan 1, 1968

By John B. Gayle

A new, experimental coke oven was installed at the Southern Experiment Station, Tuscaloosa, Ala., in 1948. This oven, designated as the Tuscaloosa oven, features a 17-inch carbonizing chamber, globar heating elements, and silica-brick heating walls designed to simulate as closely as possible carbonizing conditions in commercial, slat-type coke ovens. Zoned heat-input arrangements maintain uniform temperatures over approximately 95 percent of the total flue area. The reasons for constructing an oven of this size, the details of the design, and the operating characteristics of the oven were given in an earlier publication.2/ This report presents the results obtained from the first series of carbonizing tests on Alabama coals with the new oven. Factors leading to the development of standardized operating and testing procedures and the results of crosscheck determinations with a commercial oven producing foundry coke are included also.

Jan 1, 1954

By P. L. Sibrell

Electrorefining of Ti in nonaqueous solvents has been studied by the U.S. Bureau of mines as a method for recycling impure scrap Ti. Electrochemical behavior of Ti species was investigated using cyclic voltammetry. Research results showed that Ti metal can be dissolved in polar solvents such as dimethylformamide or dimethyl sulfoxide. However, deposition of Ti from these solvents was not successful. Several solvent systems were investigated for electrodeposition of Ti but no deposits were obtained. Reduction of Ti4+ complexes to Ti3+ proved to be straightforward, but reduction to lower oxidation states could not be confirmed. In dimethylformamide solutions, cyclic voltammetry results demonstrated the reduction of Ti to an oxidation state of less than three, but no Ti metal was identified. In dimethyl sulfoxide solutions containing LiCl, it was possible to deposit Li metal. After adding Ti salts to the solution, electrolysis quickly passivated the electrode. Deposition of Ti was also investigated in solutions of dimethoxyethane and propylene carbonate but, again, no reduction of Ti to oxidation states of less than three occurred. Therefore, the prospects for a nonaqueous electrorefining system for Ti metal do not appear promising.

Jan 1, 2010

By M. G. Zabetakis

Benzene and toluene are the first two members of an important homologous series whose general formula is CnH2n-6. The members of this series differ in composition from benzene by some integral multiple of CH2; they can all be prepared in the laboratory by the Wurtz-Fittig, Friedel-Crafts and Grignard syntheses. Because &apos;of the industrial importance of these-hydrocarbons, the limits of flammability of eight members of the series have been determined at 100° C.-(A temperature of 1000 C. was chosen because the determination of the upper limit of flammability of p-cymene requires an apparatus temperature. of at least 90° C. As elevated temperature data are available for other combustibles at 100° C. but not at 90° C., all data were taken at 100° C. in order to obtain comparable results.) Minimum ignition temperatures of these combustibles have been determined at laboratory-pressures.

Jan 1, 1951