Search Documents

Develop methods to detect and repair poorly functioning dust collectors on roof bolters. Approach In conjunction with a research project to reduce silica dust in coal mines, a variety of roof bolting machines operating under different conditions were examined to find out how much these machines were contributing to the silica dust problem. Results The investigation concluded that if the bolting machines' dust collector is properly maintained, very little dust can be measured in the air, even with minimal airflow over the bolter. Poor maintenance, however, frequently results in high dust levels. Three major problem areas were found. These were: (1) filter leaks, which allowed dust to escape, (2) accumulations of dust in the collection system, and (3) low airflow at the bit due to hose, fitting, and relief valve leaks.

Jan 1, 1984

By K. E. Stanfield

The Bureau of Mines oil-shale program, initiated in April 1944, is concerned with the future utilization of oil shale in the United States as a source of liquid fuel. One phase of this program is the accumulation of information on the location, extent, and richness of oil-shale deposits that may be suitable for processing to oil and related products. A previous publication5/ presented, by means of logs, the oil yields of sections of the largest known oil-shale deposit in this country -the shales of the Green River formation occurring in adjoining portions of the states of Colorado, Utah, and Wyoming. This present supplementary report presents the oil yields of cores from 48 holes drilled during 1952 to 1954 in the Green River formation of Colorado, which is distributed over an area of more than 1,000 square miles. The oil yields of the 48 oil-shale sections, involving the assay of 9,651 samples, representing 22,451 feet of core, are presented by means of logs. In addition, the oil yields of samples comprising the maximum sections of 15 gallon-per-ton shale are tabulated for these cores and for the 28 cores from Colorado which were logged in the previous report.

Jan 1, 1957

By Charles F. Weber

Premature blasts of charges of explosives have caused many deaths in anthracite mines, and the causes of many of the blasts were not determined satisfactorily. Investigators often found fairly high potential differences between such metallic objects as rails, pipes, conveyor lines, or sheet-iron chutes in the working place where an accident had occurred. At one mine where a premature blast occurred in a rock tunnel, one workman was killed and two others were injured, and several days later a potential difference large enough to explode an electric squib was detected between the compressed-air pipe and the track rail; the voltage fluctuated and appeared to change with the movement of a locomotive. At another mine, a. workman was killed when a primed cartridge that he was about to load in a blast hole exploded in his hand. During the investigation, a potential difference was found between the conveyor line and the sheet-iron chute. During a 5-year Period, 61 fatalities and 771 nonfatal injuries were caused by explosives accidents in anthracite mines, and one of the chief causes of these accidents was premature blasts.

Jan 1, 1950

By D. P. Schlick

As of June 30, 1970, Federal regulations required the operator of each underground coal mine to maintain the average concentration of respirable dust below legislative standards. As of March 1, 1971, over 152,000 respirable dust samples have been processed by the Bureau of Mines. Approximately 75 percent of underground working sections are being sampled in accordance with Federal regulations. Results indicate that 72 percent of the sections which have completed at least one basic sampling cycle are below 3.0 mg/m3, the standard in effect under the Federal Coal Mine Health and Safety Act of 1969 (P.L. 91-173). Notices of Violation were issued on 1,670 underground mines for failure to begin a sampling program; Withdrawal Orders were issued in 64 of these instances. Notices of Violation were issued on 1,121 sections where applicable dust levels were exceeded; Withdrawal Orders were issued in seven of these instances. There are 381 mining sections currently operating on permit; from the interim Compliance Panel.

Jan 1, 1971

By Lucia Kuizon

The Miranda Pine Roadless Area Review and Evaluation (RARE II) study area (No. 5114) comprises 12,600 acres (5,100 ha) in Los Padres National Forest in Santa Barbara County, California, about 15 mi (24 km) east of Santa Maria (fig. 1). Mineral investigations are made by personnel from the U.S. Bureau of Mines on National Forest lands identified as Further Planning Areas in the RARE II program. The Bureau of Mines reviewed literature, mining claim records, and production files; examined the study area; and sampled mineral properties where appropriate.

Jan 1, 1983

By J. A. Rowland

Manganese-copper alloys containing 60 percent or more electrolytic manganese exhibit an unusual combination of high vibration damping capacity with good strength properties. Properties of the pure alloys were first studied in the laboratories of the Federal Bureau of Mines and have been described in a series of technical papers1/ published from 1941-49. The unusual characteristics of these manganese-copper alloys attracted the attention of research metallurgists and several additional investigations have also been reported in the literature.2/ The engineer, also, was attracted by the combination of high strength and high vibrational damping capacity possessed by these alloys. A wide field of application in structural and machine design was obvious. However, serious difficulties encountered in commercial fabrication of structural or machine components from the alloys retarded attempts at their practical utilization. For this reason the Federal Bureau of Mines, in cooperation with the United States Navy, Bureau of Ships, undertook a program designed to develop practical methods for fabricating a selected group of the high-damping alloys. It is the purpose of this paper to summarize a part of that investigation in a form suitable for use by the metallurgist interested in commercial fabrication of the alloys.

Jan 1, 1955

By H. W. Sohns

A retort was constructed in which fine particles of shale, entrained in steam or other gaseous media, could be retorted at controlled temperatures and residence times and the effects of retorting variables upon quality and quantity of products could be determined. Studies of the effects of temperature upon products obtained from Green River (Piceance Creek Basin, Colo.) and Chattanooga (Tenn.) oil shales were completed. The feasibility of using the retort to process a shale of extremely high moisture content from Brazil also was investigated. Air was used as the entraining medium in a series of studies in which combustion of some of the products of retorting within the retort tube supplied a major portion of the process heat. In another series, shale oil from a conventional retort was cracked thermally to obtain data for comparison with results of retorting en-trained shale. In still another series the effects of rates of steam flow and solids feed upon rates of heat transfer from the furnace to the process stream were studied. Crushed quartz rather than oil shale was charged to the retort in this series. A study was begun in which raw shale was partly retorted, the products separated, and the partially retorted shale recharged to the retort. The shale was to have been recycled until it was completely retorted in an effort to improve oil yield by recycle retorting; however, the project was terminated before the investigation was completed.

Jan 1, 1959

The Appalachian Mountains divide Pennsylvania into two distinct coal regions, bituminous and anthracite. The western region of the the state, where the majority of bituminous mines are located, is characterized by mountains and gently rolling hills. Bituminous coal seams underlie about 12,000 square miles in 28 counties. The anthracite coal region, located in the northeast, covers approximately 3,300 square miles. This area contains more than 20 different coal beds that vary in thickness from a few inches to 50 or 60 feet. The anthracite region is characterized by steeply pitching seams that require highly specialized mining techniques and present unique challenges for solving problems such as the mine subsidence associated with abandoned underground anthracite mines. For more than a century, coal has played a major role in the economic and industrial development of Pennsylvania, particularly the steel industry. Estimated bituminous reserves total 23 billion tons, or 5.3 percent of U.S. reserves, and anthracite reserves total 7.1 billion tons, or 97 percent of U.S. anthracite reserves. Pennsylvania received conditional approval of its regulatory program July 31, 1982. Pennsylvania's Abandoned Mine Land Program was approved on the same date.

Jan 1, 1992

By A. C. Fieldner

The Sectional Committee on Classification of Coals, functioning under the sponsorship of the American Society for Testing Materials and the rules of the American Standards Association, in its 1934 report recommended to the American Society for Testing-Materials5 that Specifications for Classification of Coals by Rank be adopted as tentative. These specifications, slightly modified as recommended by the Sectional Committee, in its 1935 report,6 wore approved as tentative standards by the society in 1935. The specifications rover the classification of coals according to their degree of metamorphism, or progressive alteration, in the natural eerie s from lignite to anthracite. The basic scheme of classification is according to fired carbon and calorific value (expressed in B.t.u.) calculated to the mineral-matter-free basis. The higher-rank coals are classified according to fixed carbon on the dry basis, and the lower-ran]: coals according; to B.t.u. on the moist basis, that is, containing its natural bed moisture but free of visible surface moisture. Agglutinating and weathering indices arc used to differentiate between certain adjacent groups.

Jan 1, 1935

By L. Kaufman

Fifteen boride composites were synthesized by hot pressing and evaluated by physical and incendivity testing as non-sparking tool materials. The incendivity tests, conducted at the U. S. Bureau of Mines, Albany Research Center, compared the boride compo-sites with standard cobalt-bonded tungsten carbide material used for coal cutter bits. Two titanium diboride composites and two zirconium diboride composites out-performed cobalt-bonded tungsten carbide in wear resistance and reduced tendency to cause ignitions. However, three of these candidates exhibited undesirable chipping. The remaining candidate, a TiB2-(Ni, Cu) composite, did not chip, nor did it cause ignitions at levels where cobalt-bonded tungsten carbide tools caused ignitions in the incendivity tests. Thus, this material appears to be a logical candidate for further development.

Jan 1, 1973

By Pamplinm J. W.

"INTRODUCTION For the past six years the United States Bureau of Mines in cooperation with the University of Alabama, Tuscaloosa, Ala., the Missouri School of Mines and Metallurgy, Rolla, Mo., and certain operating companies of the Florida land-pebble phosphate district have conducted an investigation to determine the amenability of phosphatic sands to concentration. 4 This paper discusses briefly an investigation of the concentration of fine phosphatic sanads of the land-pebble district of Florida. The process used - namely, the tabling of material previously given a selective oiling treatment - is new in its application to the phosphate industry, although old in principle.The feed to the standard phospidate washery is a hydraulically wined mixture of phosphate pebbles, quartz sand, and clay in which the quartz sand grains are segregated in the fine sizes. Me standard method of concentrating (washing) consists of wet-screening. at about 20 mesh to recover the plus 20-mesh material. 5 Lately some of the washeries have introduced hydraulic classifiers for sizing of the screen undersize to recover the coarser spigot products, but even this additional treatment allows much of the fine phosphate to be wasted."

Dec 1, 1932

By Duane L. Abata

Toxic gases produced by the detonation of six explosives were measured in an underground hardrock metal mine during actual mining operations. The six explosives included two semi-gelatin dynamites, three slurry explosives and an ammonium-nitrate, fuel-oil/ammonia dynamite combination. Explosives were detonated at the face of a drift and the toxic gases produced by the detonation were trapped to the end of the drift by a bulkhead located a short distance away from the face. Toxic gas concentrations were then measured with direct readout instruments and together with the containment volume, the toxic gas volumes per mass of explosive were calculated. Toxic gas measurements were found in the following ranges (ft3/lbm): N02 0.010-0.035; N02, 0.003-0.019; CO, 0.08-0.30; S02, 0.00-0.05; and C02, 0.7-1.8. Results showed that toxic gas production (ft3/lbm) correlated with the densities (kg/m3) and energy densities (kJ/kg) of the explosives tested.

Jan 1, 1978

By Alla D. Mah

Relatively pure aluminum nitride (AIN) recently has been prepared in sufficiently large amounts to permit a variety of experimental studies.4/ Several mechanical and chemical properties have been investigated, which show that this substance has good potentialities as a container for liquid aluminum, gallium, and boric oxide. The present work by the Bureau of Mines was undertaken to obtain thermo-dynamic data pertinent to the calculations regarding thermal stability and reactivity of aluminum nitride. The following measurements were made: (1) determination of the heat of formation from the elements at 298.15° K.; (2) determinations of the heat capacity over the temperature range 51° to 298.15° K. and the evaluation of the entropy at 298.15° K. therefrom; and (3) determinations of the heat content over the temperature range 298.15° to 1,800° K. These data are combined to obtain free energies of formation from the elements between 298.15° and 2,000° K.

Jan 1, 1961

By A. O. Ipsen

As part of the Bureau's intensive investigation of domestic manganese deposits, lots of ore for testing were collected by Bureau engineers during examinations of several properties in Juab County, Utah. One low-grade and two intermediate-grade samples (13.5, 25.3 and 27.5 percent manganese) were procured by engineers of the Bureau of Mines from the 900--and 1,100-foot levels of' the Tintic Standard mine, situated 2 miles southeast of Eureka, Utah. The ore bodies were described as blocks of ore approximately 60 feet long, 40 feet wide, and 20 to 100 feet deep. The manganese-iron association in the Tintic Standard ores was intimate, and no significant concentration of the low-grade sample was made by ore dressing, However, both of' the higher-grade samples were readily beneficiated to marketable manganese products. Ore from the Oxen No. 5974 claim, 2 miles northeast of Eureka, Utah was low in grade (19.4 percent manganese) and was not amenable to the production of high-grade concentrates owing to the intimacy of association of the manganese minerals with silica. However, a fair manganese recovery was obtained in a product that, when sintered, assayed plus 40 percent manganese. The ore body is reported to be a replacement in limestone and is composed of manganese oxides intermixed with silica, decomposed rhyolite, and limestone. The Fields property consists of five mineral claims situated 3 miles north of Eureka, Utah. The deposit is a replacement in a contact between limestone and a quartz dike. Tests were made on representative samples of a 50-ton lot stored on the property. Although the mineral association in the ore (22.2 percent manganese) is not particularly complex, the physical properties of the manganese minerals render the ore refractory to ore-dressing beneficiation. As the ores varied widely in physical and chemical characteristics, samples from each property were considered as separate ore-dressing problems.

Jan 1, 1949

By R. H. Schutz

This publication lists the respiratory protective devices approved by the Bureau of Mines as of December 31, 1968, and the names and addresses of their manufacturers. The purpose of this publication is to inform the public about approved equipment for safe use in mines and mineral and allied industries.

Jan 1, 1969

By R. Hogg, T. F. Dumm

"It is generally agreed that dust characteristics play a role in the development of Coal Workers' Pneumoconiosis (CWP). Unfortunately, there is a serious lack of information on what the characteristics of mine dust actually are and how they vary among different mining regions, coal seams, etc. This paucity of data can generally be attributed to the serious problems encountered in collecting sufficiently large quantities of dust for conventional analytical procedures.Personal samplers are widely used in coal mines for regulatory and enforcement purposes. Generally, these provide information only on the total (respirable) dust loading in the mine atmosphere and on the mineral matter (primarily quartz) content of the respirable dust. A procedure has been developed by which samples collected with a slightly modified personal sampler can be analyzed for particle size distribution, total mineral matter content and elemental composition, in addition to the standard mass and quartz measurements. These analyses could readily be performed on a routine basis. Shape analysis by Scanning Electron Microscope (SEM) could easily be included if appropriate shape criteria are established. Extension of the procedure to include the determination of complete size/specific gravity (composition) distributions is quite straightforward provided sufficiently large samples (at least 10 mg) can be collected. Typical sample sizes for a personal sampler carried by a miner for one shift range from about 0.5 to 2 mg.The basic procedure was developed and evaluated using synthetic mine dust prepared in the laboratory. Field tests in three working mines in Pennsylvania and West Virginia have confirmed the applicability of the approach to the real world. Particle size distribution measurements on mine dust collected in the modified personal sampler were found to agree closely with the results of simultaneous in situ measurements obtained using cascade impactors."

Mar 1, 1989

By G. J. Conroy

Cable whip occurring during normal movement of a shuttle car can result in a personnel hazard and excessive tensions in the cable. This Bureau of Mines report discusses preferred payout and reel-in torque settings to reduce cable whip. A simplified adjustment procedure is described.

Jan 1, 1974

By H. H. Storch

"INTRODUCTION The first paper of this series contained data concerning the behavior of polyhalite (K2S04.MgS04.2CaS04.2H20) upon calcination and subsequent leaching with water at 100° C. It was found that upon heating polyhalite to temperatures between 298 and 500° C. the water of crystallization is driven off, leaving, an amorphous mixture of K2S04, MgS04, and CaS04. Two transition points were located; one at 298° C. which coincides with the vigorous evolution of steam; and one at 551° C. which results in the formation of a hard mass of crystals. The latter probably consist of a solid solution If the compounds langbeinite (K2504, 2MgS04), potassium dicalcium sulphate (K2304. 2CaS04), and anhydrite (CaS04). The heat of decomposition of polyhalite at 298° C. was measured and found to be 66,000 ± 5,000 calories per mol. The optimum temperature of calcination with regard to subsequent extrac¬tion with two parts of water (at "" 0° C.) is 430 to 450° C. for 65 to 100 mesh material, if one half hour at the calcination temperature is allowed. The maximum concentration of K2S04 obtainable in the extraction of calcined polyhalite is 11.4 grams per 100 grams of water. This concentration of K2304 is considerably above the equilibrium value (3.6 g. per 100 L. of H20 at 83° C.) with respect to the solid phases polyhalite, potassium calcium pentasulphate, ¬and anhydrite. The figure 11.4 K. of K2804 per 100 g. of H20 is also somewhat than the equilibrium value (9,65 g. per 100 g, H20) with respect to the solid phases potassium calcium pentasulphate and syngenite."

Oct 1, 1930

By S. J. Page, W. E. Wallace, P. Bolsaitis, D. Eppelsheimer, M. J. Keane, J. Poston, J. Harrison

"Respirable-sized dust particles from a clay mine and mill were examined for aluminium and silicon content by scanning electron microscopy-energy dispersive X-ray analysis at incident electron energies of 5--20 keV. Most of the high silica content particles, those which had a silicon to silicon plus aluminium signal fraction, measured at 20 ke V, of0.9 or greater, showed a decrease in the silicon fraction of signal with decreasing incident electron energy, down to values of between 0.6 and 0,8 at 5 keV: this decrease was a function of particle size and composition. Simple models for silicon fractiol) of signal vs incident electron voltage suggest this behavour is due to a heterogeneous particle structure in which an aluminosilicate coating occludes the surface of a silica particle core. The coating survives incubation in a major component of pulmonary surfactant.INTRODUCTIONMINING and some other dusty workplace atmospheres are monitored for respirable dust and quartz dust for purposes of occupational health protection, respirable quartz dust being a known cause of pulmonary disease. Respirable quartz exposure data are acquired also for epidemiological research on the correlation of pulmonary disease prevalence with respirable dust composition and concentration. For these purposes quartz content often is measured on collected dust samples by X-ray diffraction or in spectroscopy. Scanning electron microscopy-energy dispersive X-ray analysis spectrometry (SEM-EDX) is also used. The first two methods measure the bulk composition of a multi-particle dust sample; SEM-EDX measures the elemental composition of single ·particles. These methods as typically applied, including SEM-EDX with a 20-30 kilo-electron volt (keV) electron beam accelerating potential, do not distinguish homogeneous distribution of impurities in a particle from possible heterogeneous surface distribution. These measurements of quartz content are not always accurate predictors of the prevalence of dust-induced disease (ROBOCK and BAUER, 1990), which implies that the biologically available quartz surface may not be equivalent to conventionally measured quartz content of respirable dust in some exposure settings. Using a minor modification of conventional scanning electron microscopy-energy dispersive X-ray analysis (SEM-EDX) protocols on samples of settled and airborne dust from a clay mine and mill we have detected heterogeneity with depth for aluminium impurity in high silica content particles, indicating that some of the quartz or 'free silica' respirable particles of the dust are aluminosilicate occluded. Coatings were not removed by incubation of the dust in a surrogate pulmonary hypophase surfactant fluid."

Jan 1, 1990

By Robert K. Koch

The Bureau of Mines investigated separating HF from HF-SiF4-H2O mixtures by passing the mixed gases through a sodium fluoride slurry in an airlift scrubber and forming a mixed precipitate of NaHF2 and Na2SiF6. The oven-dried precipitate was thermally dissociated in two stages. The first stage was carried out at 400° C and dissociated NaHF2 to NaF and HF. Condensation and analysis of the evolved HF proved it to be 97 to 99 weight-percent HF containing 0.79 to 0.99 weight-percent H2O and 10 to 93 ppm silicon. The second stage was carried out at 700° C and dissociated Na2SiF6 to NaF (for recycle) and SiF4. The quantity of HF recovered from gaseous HF-H2O-air mixtures decreased with increasing relative H2O concentrations. Air was beneficial when scrubbing extremely dilute wet HF gases. At HF partial pressures of 0.24 and 0.013 mm Hg in the scrubber entrance gases, HF partial pressures of 6.2 x 10-4 and 9 x 10-6 mm Hg were obtained, respectively, in the scrubber exit gases. Scrubber efficiencies were 99.7 and 99.3 percent.

Jan 1, 1966