Search Documents

By J. V. Batty

Various ores from deposits in the Boulder Dam Recreational Area, Clark County, Nev., were submitted for ore-dressing tests as part of the Bureau of Mines studies of western manganese ores. The Virgin River manganese deposit is situated on the Virgin River arm of Lake Mead, 5 miles from Bonelli's Point, which was formerly the junction of the Virgin and Colorado Rivers. It is 20 miles from Overton, Nev., and 26 miles from Boulder City, Nev. The ore body, composed of wadlike manganese in a tuffaceous gangue, is a flat-lying bed overlain with beds of gypsum and basalt. Two ore samples were submitted by engineers of the Bureau for ore-dressing investigation. Low-grade sample 1 was a composite of channel samples cut from outcrops of the ore body; sample 2, of intermediate manganese grade, was taken from the dump-at the exploratory shaft sunk by the Bureau. The Boulder City manganese deposit is situated in the Boulder Dam Recreational Area -3 miles southwest of Boulder City. The ore body is a manganiferous gypsum bed 32 feet thick, slightly inclined from the horizontal. The ore sample submitted-by engineers of the Bureau for-testing was taken from channel cuts in the walls of the shaft, which cuts through the bed vertically.

Jan 1, 1948

By Tobias W. Goodman, George N. Aul, Joseph Cervik

The Bureau of Mines conducted research to degasify a virgin block of coal in the Beckley Coalbed using long horizontal holes drilled in an array from the bottom of a ventilation air shaft. Eight horizontal holes and an in situ pressure hole were drilled in a radial pattern to depths ranging from 418 to 910 ft (127 to 277 m) and 205 ft (62 m), respectively. The investigation showed the shaft was in a basin saturated with water, which resulted in low gas flows from holes. The in situ pressure at 200 ft (61 m) into the coalbed was 79 psig (544.6 KN/m2). The aver- age gas and water flows for the eight holes were 94,100 ft3/day (2,665 m3/day) and 13 gal/min (49.3 l/min) . After 514 days of degasification, 18.7 million ft3 (0.53 million m3) of gas had been drained. Methane face emissions, which were measured as a section advanced toward the shaft, were reduced about 77 pct, emphasizing the value of drainage by this technique. All holes were grouted before the area around the shaft was mined.

Jan 1, 1982

By G. R. Hopkins

"Refiners are generally considered solely as fuel producers, but actually they also comprise a group one of the largest consumers of fuel. For example, during the year 1929 the refineries-burned 51,544,000 barrels of oil as fuel, or the equivalent of over 5 per cent of the crude oil processed in that year. In addition enough other fuels - coal, natural gas, refinery or still gas, and petroleum coke - were utilized to raise the total fuel consumption based on B. t. u. equivalent to more than 10 per cent of the heat value in the total crude oil run to stills. Refineries utilize fuel chiefly as the heat-forming element distillation, but also under-boilers in the formation of steam used in refining, for the heating of buildings, and in the generation of electricity.In the early days of refining, the problem of fuel utilization and fuel economy was of scant importance to the refiners. Margins of profit were comparatively high and the major portion of the operatros1 attention was directed toward increasing their throughput. However, the keen competition that has prevailed in the refining industry over the past five years or more has taught the refiners that their expenses, one of the largest items of which is the cost of fuel, must be curtailed. Thus in 1925 the refiners used an average of 829,000 B. t. u. to refine a barrel of crude oil, wheras by 1929 this average had been reduced to 639,000 B. t. u., a decline of 23 per cent (see fig. 1)Since 1925 oil has ranked first as a refinery fuel (see fig. 2). The use of natural gas increased during 1926 and 1927 but declined in 1928 and 1929. On the other hand, the use of refinery gas has grown rapidly in importance. Coal has shown a steady decline in use at refineries since 1925. Petroleum coke has never supplied more than a very small fraction of the total fuel requirements, although there has been a steady increase in its use."

Sep 1, 1930

By Robert E. Johnson

1962 was the second year of recovery from the mild 1960-61 recession. The year-to-year gain in constant dollar gross national product, our most comprehensive measure of the country's economic performance, was 6.0 percent (from $447.7 billion in 1961 to $474.8 billion in 1962). The unemployment rate declined from 6.7 percent to 5.6 percent. Although it was a good year, there were still unused resources of labor and capital which implied that the economy was operating below its potential. The year-to-year change in the Federal Reserve Board (FRB) index of industrial production of 7.6 percent masked the fact that more than one-third of the growth took place within 196L The monthly index rose only 4.8 percent during 1962, from 114.3 in January to 117.8 in September. The fact that the economy as shown by the industrial index, rose rapidly in the first half of the year only to remain on a plateau of 119-120 during the second half, led some people to fear an imminent downward turn. This did not occur. Neither production nor consumption of mineral fuels advanced as fast as the total economy. But consumption showed more gain than production, 5 percent compared with somewhat less than 4 percent. Production of both crude oil and natural gas reached new highs while bituminous coal production was the highest in 5 years.

Jan 1, 1963

By O. C. Blade

The use of Diesel fuel as a source of power is continuing to increase in the United States. The latest available figures indicate that refineries are delivering in excess of 10,000,000 barrels of this type of fuel per month. Factors contributing to this increased consumption are conversions by a number of railroads from steam to Diesel locomotives and the growing use of Diesel engines in buses, trucks, tractors, earth-moving machinery, water craft, and stationary power plants. The increasing importance of Diesel fuel has led to a need for more information on its characteristics, particularly on the grades and qualities currently being marketed. To supply this information the American Petroleum Institute and the Bureau of Mines, United States Department of the Interior, under a cooperative agreement, are conducting annual surveys of Diesel fuels produced in refineries in this country. Samples of Diesel fuel were analyzed by the manufacturers in accordance with instructions from the Motor-Fuels Survey Panel of the Automotive Research Committee of the American Petroleum Institute. Results of the analyses were transmitted to the Bureau of Mines where the data were studied am compiled as shown in the tables of this report. The first survey was made in 1950 and was published as a Bureau of Mines report. The present report shows the results of a similar survey made during 1951.

Jan 1, 1951

By J. B. Gayle

The merits of the various methods for dry-quenching coke have been the subject of numerous publications and almost equally numerous controversies for the past 40 years.5/ Most investigators have concluded that dry quenching is advantageous. Some have based their arguments on the improved physical properties of the resultant cokes. Others have claimed little or no improvement and have based their arguments on the economies acquired from the recovery and utilization of sensible heat. The extent to which the method of quenching influences the properties of the resultant cokes is of importance in connection with the operation of both commercial and experimental ovens. On the other hand, the recovery and utilization of sensible heat are economic problems related solely to commercial oven operation and- depend on the method of dry quenching used and the demand for a low intensity energy source. The scope of the present Bureau of Mines investigation has been limited to a comparative study of the properties of wet- and dry-quenched cokes produced from six coals and blends carbonized at flue temperatures of 2, 000° and 2,400° F. in the Tuscaloosa oven.

Jan 1, 1959

The Bureau of Mines found sulfur hexafluoride (SF6), released from a lecture bottle, to be an ideal gaseous tracer for studying mine ventilation systems. Air samples were collected in glass syringes and analyzed by electron-capture gas chromatography. In these studies, the lower limit of detection was about I part per billion by volume (ppb) of SF6 per part of air. Experiments conducted in a Pennsylvania limestone mine showed this technique useful in evaluating the effectiveness of auxiliary fans, measuring low flow velocities, probing the air circulating near a working face region where ventilation appeared to be poor, and estimating volumetric flow rates in airways of large cross-sectional area and having low flow velocities. This technique was also used in a western vein-type metal mine to measure the amount of return air being recirculated into the intake air due to leakage through old stoped areas.

Jan 1, 1974

By Roy E. Peterson

The Bureau of Mines conducted an investigation to produce metallized pellets from domestic iron ore superconcentrates using lignite and subbituminous coal as reductants. Feed materials for the metallizing process consisted of commercially indurated iron oxide pellets and green pellets prepared from upgraded domestic concentrates with graphite or limestone as internal additives. Durability of the green pellets during metallization was investigated in tests conducted in a 7-inch-ID rotating drum furnace. Test results indicated that the major cause of pellet disintegration with the concentrates used was the tumbling action during reduction rather than forces generated within the pellets. In larger scale tests made in a 34-inch-ID by 35-foot-long kiln, the previously indurated pellets were metallized with lignite at 1,030° C with little disintegration. A 96-percent level of metallization was obtained in pellets having an average compressive strength of 420 lb. In subsequent, similar tests using green pellets containing graphite or limestone, pellet disintegration was more severe, with 10 to 40 percent of the feed being lost as dust. The surviving pellets had metallizations ranging from 88.3 to 94.4 percent and compressive strengths ranging from 60 to 68 lb.

Jan 1, 1976

By R. L. Gall

This report describes Bureau of Mines experiments in gasifying coal in a helium-heated tube-coil reactor. The purpose of this work was to investigate helium as a medium for transferring heat from a nuclear reactor to gasify coal or for use as high-temperature process heat. A laboratory-scale system was designed and constructed to demonstrate feasibility. In preliminary tests with this system, in which the coal was fed as a water slurry, the helium-heating and recycling equipment operated well. Considerable difficulty was experienced, however, in preheating coal slurry to the desired range of 400° - 1,000° F. without plugging the preheaters. Five different preheaters plugged with coke or with salts leached from the coal. The longest operating period wan 12 hours. These difficulties were partly due to the relatively small equipment and flow rates. The gasifier processed l pound per hour of low-rank coal at 300 p.s.i.g. and 1,800° F., with the carbon conversion limited to 20 to 30 percent by the short residence time and slow heat-transfer rate.

Jan 1, 1962

By D. H. Baker

THIS REPORT presents the technique and equipment used in determining the hardness of titanium sponge. Detailed descriptions are given of the methods used in preparing test samples for chemical analysis and hardness testing, the method of melting and surfacing test ingots, and the technique of reading Brinell-hardness impressions. The arc-melting furnace described, for which engineering drawings are included, will produce from 70 to 90 double-melted buttons each 8 hours of operation. Experimental data are also presented depicting the effect on hardness of the methods of surfacing specimens, temperature of test specimens, and the effect of time at test load. These data show that surfacing of the specimen involves no critical machining operations but that the test surface must be paralleled by a relatively flat surface for contact with the anvil of the Brinell tester. The heating of a specimen to 150° C. during surfacing does not materially affect the results if the ingot is cooled to room temperature before the hardness impressions are made. The optimum time at load appears to be approximately 30 seconds, but load times of as much as 1/ ½ minutes will not cause major errors.

Jan 1, 1959

By R. Hogg

"The basic population balance models for agglomeration processes are reviewed and procedures are described for extending their applicability to systems with size-dependent rate constants and to the formation and growth of porous agglomerates from rigid, solid-particles. Simplified procedures for the further extension of the models to include simultaneous agglomerate growth and breakage are also described.INTRODUCTION The association of small particles into clusters or agglomerates is a significant factor in many facets of particle processing. Agglomeration processes are widely used to facilitate handling, storage and utilization of fine powders. Processes such as coagulation or flocculation are used to aid solid-fluid separation in dispersed particulate systems. Agglomeration also occurs as an accompaniment, often unwanted, to other particulate processing operations such as fine grinding, mixing and blending, transport and flow.Reliable agglomeration models are needed for improved understanding of the processes in general and of the complex role of numerous, interacting variables as well as for direct application to the design and control of industrial processes such as flocculation, granulation and pelletization. Ideally, the models should account for the primary forces responsible for agglomerate formation and growth, the effects of external forces on process dynamics, the development of agglomerate structure and its role in the process itself, and the effects of concurrent processes such as structure modification (e.g. compaction) and agglomerate breakage or degradation."

Jan 1, 1989

By S. L. Windes

This report presents physical and petrographic properties of approximately 60 types of rock from operating mines or mineral-investigation projects and supplements Repot of Investigations 4459, Physical Properties of Mine Rock (hereinafter referred to as Part I). The physical properties evaluated include the following: Apparent specific gravity Apparent porosity Compressive strength Flexural strength (modulus of rupture) Impact touchiness Abrasion hardness Scleroscope hardness Modulus of elasticity (Yourg?s modulus) Modulus of rigidity Specific damping capacity Longitudinal bar velocity

Jan 1, 1950

By Clarence Karr

AN EXTENSIVE characterization was conducted on the neutral oil components in a low-temperature bituminous coal tar. A total of tai individual compounds identified with respect to individual isomers, and at least 55 other compounds were indicated to be present. The amounts were determined in all instances. A comparison of isomeric distribution in the tar with thermo-dynamic equilibrium distribution, and kinetic distributions indicated that the composition of the tar largely reflected the structure of the coal from which it was formed. Detailed descriptions are presented for the separatory and qualitative and quantitative procedures for the characterization of the neutral oil component. These include micro fractional vacuum distillation, displacement liquid chromatography, gas-liquid chromatography, countercurrent distribution, and infrared and ultraviolet spectrophotometry. Descriptions are given for the synthesis of authentic specimens of alkylindenes, The ultraviolet and infrared spectra of 134 polycyclic compounds, ranging from alkylindenes to alkylphenanthrenes, either found in the distillable neutral oil, or thought likely to be present, are also given.

Jan 1, 1967

By F. P. Haver

Because State and Federal agencies have limited the amount of sulfur oxides that can be discharged to the atmosphere, most copper smelters plan to convert the S02 in offgases to sulfuric acid. In some cases, however, it might be preferable to use a nonsmelting method to fix the sulfur in the form of a discardable product. Research by the Federal Bureau of Mines has shown that sulfur in copper concentrate can be converted into insoluble anhydrite (CaS04) by roasting the concentrate with lime (CaO). After leaching the calcine to recover metal values, the residue may be discarded without harm to the environment. The process can use a rougher flotation product, thus reducing separation costs and saving valuable minerals (for example, molybdenite) that are now lost in making cleaner concentrate. In tests, rougher concentrate was pelletized with the theoretical amount of lime and roasted for 1 hour in a 6-1/2-inch-ID by 11-foot-long rotary kiln at 700° C. Sulfur retention was about 97 percent. Leaching the calcine with 20 percent RCI extracted approximately 99 percent of the copper, 73 percent of the iron, and 91 percent of the molybdenum. After the molybdenum was removed from the leach solution by adsorption on activated carbon, copper with a purity in excess of 99 percent was obtained by cementation on sponge iron. The strip solution then could be spray-roasted at 500° C to recover the RCI for recycle and obtain F2O3 as a byproduct.

Jan 1, 1975

By G. W. Jones

In cooperation with the Edison Electric Illuminating Co. of Boston, Mass., and the Boston Consolidated Gas Co., a survey has been conducted continuously since 1929 by the Bureau of Mines to determine the general hazards of combustible gases and vapors in manholes of the Edison Electric Illuminating Co. The New England Telephone & Telegraph Co. also has cooperated in the investigation, and tests have been made in its manholes since May 1, 1933. Yearly reports6/ on the results obtained since the beginning of the survey have been published. The method and procedure of conducting the survey in 1936 were the same as heretofore.

Jan 1, 1938

By G. W. Jones

In cooperation with the Edison Electric Illuminating Co. of Boston, Mass., and the Boston Consolidated Gas Co., a survey has been conducted continuously since 1929 by the Bureau of Mines to determine the general hazards of combustible gases and vapors in manholes of the Edison Electric Illuminating Co. The New England Telephone & Telegraph Co. also has cooperated in the investigation, and tests have been made in its manholes since May 1, 1933. Yearly reports6/ on the results obtained since the beginning of the survey have been published. The method and procedure of conducting the survey in 1936 were the same as heretofore.

Jan 1, 1938

By C. R. Stephan, N. B. Greninger, J. R. Lipscomb

The U.S. Bureau of Mines and the U.S. Mine Safety and Health Administration (MSHA) are participating jointly in a research program to evaluate the strength characteristics and air-leakage resistance of various proposed seal designs for use in underground coal mines. The full-scale seals were constructed in the USBM's experimental mine at the Lake Lynn Laboratory, air-leakage tested, then subjected to pressure pulses of 20 psig or greater. bjected to pressure pulses of 20 psig or greater. In experiments prior to this study, seven seal designs using solid-concrete blocks were tested. Only the standard-type seal passed the explosion and air-leakage criteria. Tests also were performed on four seals constructed with low-density foam blocks. All four of these seal designs withstood the pressure pulse. In more recent studies, nine cementitious foam seal designs of varying thicknesses and densities were investigated. Six of the nine designs successfully survived the explosion overpressures. Six wood- block convergence seals also have been tested. The typical 3-ft-thick, wood-block seal design currently used in many coal mines did not maintain its integrity, in the absence of convergence forces, following the explosion test. Five modified wood-block seals successfully withstood the 20-psig pressure pulse. Based on these tests, three alternative seal construction materials, cementitious foam, low-density foam block, and wood, have been approved by MSHA for use in underground coal mines.

Jan 1, 1993

By David Burgess

Natural gas is a general term applied to the gas obtained from oil or gas wells. It is the most widely used of all gaseous fuels. The principal disadvantage in the use of this and other gaseous fuels is the difficulty encountered in the storage and transportation of large quantities in the gas state. Handling in the liquid state is possible, but reduced temperatures are required since methane (table 1) is the principal component of most natural gases that are used as fuels. Actually, liquid storage has been utilized both here and abroad;3 however, the Cleveland disaster4 has pointed out the need for a critical evaluation of the hazards involved in the storage of this cryogenic fuel. Accordingly, a program was undertaken to obtain basic data that could be used to assess these hazards. In this report, the factors to be considered in an evaluation of the fire and explosion hazards associated with any fuel are each discussed briefly. These factors are then used to assist in the design of experiments for the evaluation of the hazards associated with liquefied natural gas (LNG) relative to those associated with other common fuels. Experiments have been conducted on the vaporization of LNG, the mixing of LNG vapors with air, the effect of temperature and nitrogen dilution on the limits of flammability of methane in air, the burning rates of LNG and other fuels, flame radiation, and extinguishment of fires above liquid pools. Based on the results of these experiments, LNG can be stored safely in suitably designed above-ground tanks surrounded by earthen dikes in much the same manner as gasoline.

Jan 1, 1962

By H. Tomlinson

"PURPOSE OF REPORTFatalities from falls of roof and coal are responsible for the death of more than 1,000 miners annually in the bituminous coal mines of the United States or practically one—half of the total fatalities in and about these mines. The men are killed by falls singly or in small groups and little or no publicity is given these accidents as they lack the spectacular features of gas and dust explosions. As a result, the public and even the miners have the impression that accidents from falls of roof and coal are just one of the unavoidable hazards of the coal—mining industry. This belief is not true. Accidents caused by falls can be avoided largely by the application of sound engineering principles, by education, and by proper leadership in the industry, just as gas and dust explosions and accidents caused by explosives have been reduced in recent years.The necessity for studying falls of roof and coal becomes apparent by referring to the following data from a table by Adams and Chenoweth:3"

Jan 1, 1933

Provide reasonably priced, reliable fire protection for large walking draglines. Approach Fire hazards on large draglines were analyzed, then appropriate automatic fire sensing and suppression systems developed and in-mine tested. How It Works Five fire hazard areas identified for special attention are: electrical control room, high voltage transformer enclosures, circuit breaker rooms, collector ring/roller path area, and the automatic lubrication rooms. Automatic fire sensing and suppression systems were separately designed for each area. The design of each system was tailored to the hazards and equipment protected. Spot thermal sensing and Halon 1301 suppression were specified for the electrical

Jan 1, 1981