Search Documents

By James A. Wasson

This report analyzes the petroleum-production potential of the basal Greenbrier dolomite zone, Sycamore-Millstone field, Sherman District, Calhoun County, W. Va., through the application of certain secondary-recovery methods. The well logs obtained and the core recovered from a well in this formation permitted an evaluation of the productive capability of the reservoir, Approximately 120,000 stb of oil may be produced from a 20-acre five-spot unit at breakthrough if the property is waterflooded. At an assumed limiting producing gas-oil ratio of 20)000 sef/stb, approximately 69,000 stb of oil should be recovered by low-pressure gas drive.

Jan 1, 1967

By P. J. Remington

Field measurements utilizing a seat pad accelerometer were made on 61 surface coal mining machines in order to quantify the vibration levels experienced by the operators. Those data were combined with information on the statistics of the operating times of those machines in order to compare the operator's vibration exposure to the criteria in ISO 2631, ?A Guide for the Evaluation of Human Exposure to Whole Body Vibration.? The comparison showed that about ha]f of all surface coal mining machine operators can be expected to be exposed to vibration exceeding the fatigue decreased proficiency criterion, whereas only on the order of 15% would be expected to experience vibration exceeding the exposure limit. Detailed exposure statistics are presented and the implications of the results are discussed.

Jan 1, 1983

By Hendrik Gerritsen

The research to be described is directed to the construction of an instrument that detects methane in air. The principle on which it is based is that methane gas absorbs infrared radiation in the wavelength range of about 3.2 to 3.4 micron. Solid state p-n junctions of composition In, .97Ca.03As emitting radiation in a band centered at 3.3 micron were grown by liquid epitaxy on InAs. Fight separate growth cycles and a total of 200 diodes were measured to determine total power, wavelength peak, spectral. half width and reproducibility of the method. In order to compensate for temperature changes, dual emitter systems (one InGaAs, and one InAs diode) mounted on the same TO-5 header were made. These devices were imaged, using a folded optical path cell, on large area InAs detectors, grown by a planar diffusion technique. In the 0-50°C range the primary temperature sensitivity is in the InAs detector rather than in the emitters. Several methods to reduce the overall temperature sensitivity to within acceptable limits were demonstrated. Humidity was shown to have a negligible effect on the measurements.

Jan 1, 1976

By Constantine C. Popoff

During 1946 several high-grade limestone deposits in western Washington were examined by the Federal Bureau of Mines. The purpose of the examinations was to disclose new sources of industrial limestone and to indicate the commercial potentialities of little-known and undeveloped deposits. These examinations were part of a long-range program of investigation of mineral resources of the Pacific Northwest. The following report on the Whitechuck travortine deposit is one of a series prepared in the course of the investigations.

Jan 1, 1949

By Almon F. Robertson

The floor of Shady Valley, Johnson County, Tenn., is underlain by the Shady dolomite formation. In places the residual clay derived from this formation contains considerable manganese oxides. Nine properties in Shady Valley and two in Doe Valley were prospected by the Bureau of Mines from January 1943 to April 1943. The results obtained indicate that the ore bodies are small and spotty and, that the ore is not well-adapted to gravity concentration. The work of the Bureau was confined to the open end of the valley. One mile northeast of the Ham Greer property, Beaverdam Creek enters a rocky gorge, and it was believed that the few prospects in this area were of secondary impor-tance and, owing to the steep slope and general roughness of the terrain, that exploration with the rite', bucket-drill would be impracticable. A total of 4,398.5 feet was drilled in 131 holes. In addition, 235 lineal feet of bulldozer trenches were cut and 4.5 feet of test pits were sunk. The following nine properties were explored in Shady Valley: Bentley, Walker, Blevins, Scott, North Ham Greer, South Ham Greer, Lipford, Blackburn, and Steagall In Doe Valley, the Gerd Shoun and Brookshire properties were explored.

Jan 1, 1949

By R. S. Norman

The objective of this program was to select approximately 100 acoustic materials for flammability evaluation. Noise control programs have been initiated on several types of mining equipment and vehicles which can be used in underground coal mines. Often, the materials which are used in these noise reduction programs have not been tested for flammability properties according to the same reference standard. During this program a variety of materials were selected for measurement according to ASTM E-162 procedures. A radiant heat energy source was used to measure flammability properties of 15.2 x 45.7 cm. samples. In the absorptive materials category, 45 percent of the materials tested had a flame spread index of less than 25. For barrier, damping, and isolation materials the corresponding values were 40, 43, and 9 percent.

Jan 1, 1979

By E. S. Leaver

The gold that is not recovered by a particular process is refractory to that process. A study to determine how the refractory gold is associated in the ore constituents usually indicates the needed improvement in the process or additional methods for bettering recovery. In preliminary work, segregation of the various minerals, gangue or impurities, and data showing the reactions of each in the recovery method readily confines the refractory gold to a certain part on which extensive research can be directed. In this dissecting plan, the microscope is an important aid in locating the refractory gold but should be supplemented by chemical tests. Each ore is an individual problem until the association of the gold has been determined. Knowing the problem through the interfering minerals or elements, the solution often is only the application of part of a former known practice as an auxiliary or additional feature. In the treatment plan for most gold ores, it has been the custom to try each of the usual recovery methods or combinations thereof, accepting the best results on a basis of the lowest cost. A better plan includes knowledge of the association of the gold and the various minerals from which it is to be recovered. This presents reasonable foresight into the problems that should be expected and permits some provision for avoiding probable difficulties. The preliminary work should include: Determination of the percentage of free gold with classification showing size of gold particles to be expected; determination of the percentage of gold associated with each mineral and whether it be freed from the mineral by crushing; and an analysis of representative samples of the ore to include other valuable minerals and the form in which they occur.

Jan 1, 1934

By G. A. Apell

The presence of considerable mineralization at the surface together with other favorable conditions suggested inclusion of the Nigger Jim diggings area in a comprehensive study of shallow lead deposits in southwestern Wisconsin. The area, which was the site of considerable shallow development some 60 to 70 years ago, offered the possibility of substantial quantities of lead at near-surface horizons. The investigation included completion of 30 churn-drill holes totaling 1,808 feet of drilling, 2 diamond-drill holes totaling 164.5 feet of drilling, and 25 feet of test pitting in two excavations. The degree of mineralization was determined in an area l,500 feet long and 150 to 300 feet wide along a mineralized trend that has not been investigated beyond the limits of the zone drilled by the Bureau of Mines.

Jan 1, 1948

By Kenneth M. Earl

In its investigation of deposits of strategic minerals, the Bureau of Mines did some diamond drilling at the Almedia deposit In an endeavor to find an additional source of supply of lead and zinc. It is reported that in 1816, lead and zinc minerals were found in the limestone quarries near the boundary line between Scott and Center townships. In an attempt to develop these minerals in paying quantities, an alit was driven for several rods into a bluff Just west of the present Almedia mine, This is believed to be the Web mine, mentioned briefly by Parker Cleaveland in 1816. In 1901 the Almedia mine was developed by an open cut and three shafts. The hoisting shaft at the time of drilling by the Bureau of Mines was sounded to a depth of 115 feet. A concentrating plant reportedly made shipments to Hamburg, Germany, for reduction. The deposit is in a somewhat slaty limestone. The ore occurs in a northeast fracture zone along the strike of the limestone and dips to the southeast. Old miners state that the ore appeared as large chunks of galena and sphalerite. In 1949, to investigate the downward extension of the oreshoot, the Bureau of Mines drilled four holes aggregating 1,126.3 feet.

Jan 1, 1950

By A. E. Harak

To determine the retorting characteristics of a column of mine-run, ungraded oil shale ranging in size from fines to pieces weighing as much as 5 tons, a 150-ton batch retort was designed and constructed at the Laramie Energy Research Center, Laramie, Wyo. The retort vessel is 45 feet high by 11-1/2 feel in inside diameter and is supported in a 92-Foot-high steel superstructure. Mine-run shale from the Bureau of Mines facility near Rifle, Colo., assaying about 25 gallons of oil per ton, is currently being used as the test shale. To date, three runs have been completed. Results of the second and third runs are reported in this paper. The two runs considered in this report are the first of a series of nine to determine operating conditions that will yield maximum oil recovery from a column of mine-run shale. Variables studied :ire the oxygen content of the retorting gas and the space velocity of the retorting gas expressed as ft3 gas/ft3 bed/min. Oil recoveries for the two runs reported are 62.2 volume percent of Fischer assay for the run using higher oxygen and space velocity, compared with 39.3 volume-percent when less oxygen and a Lower space velocity were used.

Jan 1, 1971

By John C. Gagliardi, Walter K. Utt

The U.S. Bureau of Mines, in cooperation with Carter Mining Co., conducted vibration tests of four off-road vehicle seats. The purpose of the tests was to determine which seat provided the best vibration attenuation under laboratory conditions. Laboratory tests were constructed to simulate the mining vibration environment within the limitations of the test equipment. The acceleration test levels and corresponding response of the seats were low compared to IS0 2631's fatigue-decreased-proficiency time limits. Two of the seats employed mechanical suspensions and two seats employed air suspensions. The seats were tested using a 22,241-N (5,000-lbf) electrodynamic shaker. Mechanical suspension seats were tested with various preload-to-mass ratios (PMR's) and cushion densities. Air suspension seats were tested with various air pressure levels and seat cushion densities. Air suspension seats provided good vibration attenuation if pressurized greater than 552 kPa (80 psi). Mechanical suspension seats' attenuation performance decreased if the PMR exceeded 9.8. Seat cushions of lower density provided less vibration damping.

Jan 1, 1993

By Floyd G. Anderson

A study was made of the effectiveness of dust-control methods being employed in connection with continuous-mining operations. Airborne dust exposures of workmen and dust loadings of return air were determined for six types of continuous-mining machines. The conditions required for control of dust exposure are summarized and include ventilation of the working face by an exhaust system. Return-air dust loadings ranging up to 13 pounds per hour are reported.

Jan 1, 1963

By Michael Sokaski

The Cliff Springs prospect in the northern part of the Slate Range Wilderness Study Area (WSA) contains only minor amounts of gold and silver. Clay near this prospect contains insufficient aluminum to be of economic interest, although alunite claims are recorded in the vicinity. Mineralized rock at the Crescent Mine adjacent to the WSA contains gold, silver and lead occurrences. The host rock may be present in the extreme southwestern part of the WSA, which is covered by alluvium. Substantial sand and gravel deposits are present but these occurrences are remote from markets. Much of the USA is underlain by volcanic rocks and alluvium and consequently the mineral resource potential there remains unknown.

Jan 1, 1983

By J. M. Stuve

Calorimetric data for the dissolution of scandium sesquioxide and scandium trichloride in 4.360 molal hydrochloric acid were used to evaluate the standard heat of formation of ScCl3(c). The heat of reaction for Sc(c) + 1.5Cl2(g) = ScCl3(c) at 298.15° K was computed as -225,440 ±340 cal/mole.

Jan 1, 1965

By W. E. Brown, P. R. Porath, V. Miller, C. E. Wood, C. Prasky, E. P. Barrett

"INTRODUCTION This investigation was a part at the Bureau of Mines program for the production of critical and essential materials needed for the war.The Boykin Committee for investigating the steel shortage aided in obtaining an appropriation to be expended by the Bureau of Mines in studying the utilization of North Dakota lignite in the manufacture of hydrogen that could be used in the production of sponge iron from low grade ores of Minnesota.OBJECT OF INVESTIGATIONThe investigation was conducted by the Bureau of Mines to ""determine the workability of the proposed bubble-hearth process and its possible use in connection with an experimental plant for the gasification of lignite being operated by the Coal Division of the Bureau of Mines at Grand Forks, North Dakota.ACKNOWLEDGMENTSThis report is one of many on various aspects of the Bureau of Mines program directed toward the more effective utilization of our mineral resources.Investigations of our mineral resources are conducted by the Mining Branch, L. B. Moon, chief, and by the Metallurgical Branch, O. C. Ralston, chief.The scope of the report falls in the province of the Metallurgical Branch, whose activities embrace the separation of difficulty beneficiated ores, the production of pure metals from domestic deposits, the exploration of marginal ore reserves, the recovery of secondary metals, and the improvement of present industrial metallurgical practice."

Jun 1, 1947

By GEORGE S. POPE

The purchase of coal by the Government under specifications depending on the heating value of the coal, its content of ash and of moisture, and other considerations, rather than upon the reputation or trade name of the coal, was based on the fuel investigations begun by the Technologic Branch of the United States Geological Survey in 1904. The plan was first adopted by the Treasury Department in 1906. Since then the plan, variously modified in form but the same in principle, has been gradually adopted by other departments until at present of the coal used by the Government, the total value of which approximates $8,000,000 annually, more than half is purchased under specifications. The Government publications dealing with the adoption by the Government of the specification plan, the number of contracts awarded on that basis, and the quality of the coal delivered under such contracts in the several fiscal years covered by the reports are given in publications listed at the end of this bulletin. Under the authority of acts of Congress making appropriations for analyzing and testing fuels belonging to or for the use of the United States Government, a laboratory is maintained at the headquarters of the Bureau of Mines, Washington, D. C., where samples represent- ing deliveries of coal purchased under specifications for Government use are analyzed and tested. At this laboratory more than 1,200 samples have been analyzed and tested in one month. With the complete equipment and the efficient force employed, the analytical work has been so perfected that the analyses and heating-value tests of the samples received are as accurate as may be reasonably expected in laboratory work of this nature. One of the serious drawbacks to the general adoption of the speci- fication method for the purchase of coal is the difficulty of obtaining at reasonable cost samples of coal that can be considered fairly repre- sentative of the commercial product delivered in wagons, railroad

Jan 1, 1913

By O. C. Blade

This report on the properties of aviation gasolines and aviation jet fuels produced in the United States during 1954 was made under a co-operative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. Analytical data are presented for 101 samples of aviation gasoline. Data also are given for 30 samples of aviation jet fuel. The analyses were made on samples typical of the manufacturers I 1954 production in their laboratories and the results submitted to the Bureau of Mines for compilation. The products of 19 manufacturers of aviation gasolines and of 15 producers of aviation jet fuels are represented.

Jan 1, 1955

By James E. Bell

Quartz crystals occur on a farm in the vicinity of Laurel Fork, Carroll County, Va., in abundance over a large area, This has been known for several years, but no work had been clone, up to the Bureau of Mines examination in 1943, to determine the amount of crystalline quartz of usable quality. Field exploration was undertaken throughout the month of June 1943.

Jan 1, 1950

By Robert P. Vinson

A sequential sampler, based on the Archimedes screw, has been developed by the Bureau of Mines. Its initial purpose was to collect air samples during tracer gas studies in underground mines. However, the basic concept can be applied to other sampling needs, including sampling of liquids. A prototype was built and successfully tested in the Bureau's Experimental Mine at Bruceton, Pa. The simple design makes the sampler inherently durable and low in cost.

Jan 1, 1976

By Larry A. Haas

The U.S. Bureau of Mines is investigating ways of enhancing the high-temperature softening-melting (HTSM) properties of domestic taconite pellets. These properties, which are important for determining the performance of pellets in blast furnaces, include pellet bed contraction, pressure drop, S-value (area under the pressure-temperature curve), and softening and metal-slag drainout temperatures. Experiments showed that HTSM properties were related to the physiochemical properties (fired strengths and reducibilities) of pellets containing different levels of limestone and dolomite flux. Flux additions resulted in slightly lower green and fired pellet strengths, but improved metallurgical properties, such as reducibility. The influence of reduction conditions on HTSM properties was evaluated by varying the pellet metallization starting temperature and the carbon monoxide content of the CO-N2 gas mixture. HTSM property change was more sensitive to flux addition levels when metallization was initiated at 1,100° C with 20 pct CO in the gas stream. The S-value and the metal-slag drainout temperature were found to be the best criteria for characterizing HTSM properties. The optimum flux addition level was about 8 pct (4 pct dolomite, 4 pct limestone) or a basicity of about 1. At higher flux levels, a higher metal-slag drainout temperature was obtained.

Jan 1, 2010