Search Documents

By John R. Shattuck

As a part of the general chromite investigation in California designed to aid In the production of chromite during the recent war emergency, the Bureau of Mines explored the Coggins property in Siskiyou County, Work by the Bureau in cooperation with the Federal Geological Survey began in October 1942 and was concluded in March 1943. This report presents a brief history of the mine, outlines the physical features of the district, describes the deposits) and explains the work completed by the Bureau of Mines, Table 1 shows the analysis of diamond drill-hole samples. The logs of drill holes are in the appendix.

Jan 1, 1949

By Jr. Allan

"Although the advantages of large-capacity air receivers for underground mines are plainly evident from published information about various installations in the United States and abroad, details of their construction are not generally known in this country., Ordinary present-day air-compressor installations servicing mining machines are designed to supply air at a specified pressure in sufficient quantity to meet the peak demand of the mine,2/ although this demand may exist for only a few minutes out of 24 hours and, as usually happens, eventually exceeds the capacity of the compressor. Most of the receivers provided with these compressors (to a certain degree of standardi¬zation) are capable of storing a volume of air approximately equal to that compressed in 1 minute by the machine.3, 4/ As a result, during peak-load periods the compressor operates at full load capacity without maintaining kick-off pressure. At other periods of the work cycle, production of compressed air is intermittent.At least one large mine5/ has adopted large-capacity receivers to reduce wear on its air-compressing system caused by the sudden demand of peak loads. Under the old system, the compressors jumped suddenly from half speed to full speed; boilers furnishing steam to the compressors were taxed heavily to provide the increased requirements of power; and machines using the air, among which were four large hoists, were required to operate at 65 pounds per square inch rather than at the 90 pounds per square inch for which the compressors were regulated. Operation of air machines, especially drills, at pressures lower than those for which they were designed decreases their efficiency and increases maintenance costs. In addition, air that comes directly from the compressors has had little opportunity to cool and dry enroute.6./ As a result, quantities of compressor lubricant and water are carried into the machines that use the air. When expansion occurs in the cylinder or turbine of such engines, the temperature of the air drops, and this oil and water is precipitated. The water washes away lubricating oils in the machine, causing poor performance and high cost of maintenance; the compressor oil, in addition to being a poor lubricant for compresed-air engines, exerts a corrosive action on gaskets and rubber hoses.7/Reduction of peak demands on air compressors by large receivers lowers power costs by establishing more nearly constant load factors,8/ and in some cases by permitting the use of smaller compressor capacity.8,9/Load factor is the ratio of average demand to maximum demand; a low load factor costs money.10/Elimination of high-peak demands raises the load factor by making the average and the maximum demand more nearly equal. Further savings may be made possible by large receivers where their use permits charging to be done at night in regions having lower power rates during that period.11/Where ordinary receivers are used, compressor breakdowns cause immediate work stoppages in the mine owing to lack of air. Similarly, the capacity of a large receiver has been known to permit uninterrupted work in the mine until the compressors have been returned to service.9/Large-capacity receivers, either steel-tank or underground rock-chamber, offer a practical solution of many existing problems by providing a sufficient reserve of compressed air within the pressure range required for efficient operation of machines to level off peak demands on the compressor. The com¬pressors operate when the demand has reduced the pressure in the receiver below the regulating pressure and until all air used from the receiver has been replaced. It has been found possible in at least two mines,8.9/ one of which the author has visited, to entirely eliminate one compressor and to obtain more efficient performance from the remaining one by the construction of an underground coal-chamber receiver.8/"

Jan 1, 1950

By C. C. Merrill

The Bureau of Mines beneficiated the wastes generated by commercial titanium chlorination operations to reclaim metal values and reduce the problem of disposing of solid wastes. A water leach solubilized about 40 percent of the dry weight and over 75 percent of the metallic impurities. The residue from the water leach was rich in titanium dioxide and carbon; it was combined with rutile and recycled to a laboratory chlorinator. The contained carbon was used in lieu of part of the coke requirement.

Jan 1, 1969

By John Nagy

Limited experiments in the laboratory with specimens of mine rock from a Virginia bituminous coal mine indicate that natural gas-air mixtures can be ignited by sparks generated by rubbing friction of sandstone against sand-stone, shale against sandstone, sandstone against (roof-bolt) steel, and shale against steel. Such sparks, generated during a roof fall, may have initiated a recent gas explosion in this Virginia mine, although this cannot be stated with certainty. No ignitions of gas were produced by sparks or heat generated by impact friction between mine rocks or steel, during tension breaks of roof bolts, or by pull tests of roof bolts through their washers and roof plate. However, this negative result of limited experiments does not preclude the possibility of gas being ignited by these conditions.

Jan 1, 1960

By Steve Bessinger, Steve Signer, James Pile

The San Juan Mine and the National Institute for Occupational Safety and Health conducted a study to measure how development mining affected bolt loads. Twelve fully grouted, instrumented roof bolts were installed at two three-way intersections as part of the standard bolting pattern. Newly developed miniature data acquisition systems (MIDAS) were used to measure bolt load changes during initial face advance and cross-cut breakthrough. The effects of cut placement and depth on roof bolt loads were studied. This test showed how bolt loads increased at five positions along the bolt length during initial mining. Both entry advance and cross-cut breakthrough produced a similar percentage of increase in bolt loads. Geologic differences between the test sites were probably responsible for the differences in amounts of bolt loading. The test site with more top coal and a higher rock quality designation (RQD) had lower bolt loads.

By R. V. Thurston, Edmund S. Leaver

"During the development of the sulphur dioxide leaching process for the treatment of ""mixed"" copper ores at the Southwest experiment station of the Bureau of Mines*** the pulp from treatment of roasted cupriferous pyrite with sulphur dioxide gases and water showed an unexpected amount of sulphuric acid. After following out several false premises it was found that this was due to iron in the solution, and also that this iron tended to oxidize to the ferric state if the concentration of sulphur dioxide in the roaster gases used did not rise above a certain figure. While the percentage of iron present was email it was enough to cause an entirely different set of conditions from those of the original sulphur dioxide leaching process and to promise a much wider application of the general idea. Sulphurous acid dissolves only certain copper minerals, sulphuric acid solutions certain additional minerals and ferric sulphate solutions certain further additional copper minerals, so this observation was of importance in connection with possibilities in the hydrometallurgy of the so-called ""mixed"" or partly oxidized copper ores.The work has been carried along by a number of experimenters. L. R. Eckman, junior chemist of the Southwest station, contributed largely to the early developments. L. Roberts, W. D. Bonner and C. G. Maier each in turn physical chemists at the Pacific Experiment station, (Berkeley, Calif.) have studied the reactions involved. A complete report of all the work on this process will be prepared later under the direction of O. C. Rolston. The purpose of the present paper is to place a summary of the more practical phases of this seemingly important piece of work before those interested."

Dec 1, 1923

By Richard L. Sayrs

The Eve Mills deposit is in Monroe County, Tenn., near the southeastern corner of the State. The deposit was examined in February 1943 by a Bureau of Mines engineer, and drilling the property was recommended to increase the on: reserves enough to justify mining should war needs require it. The deposits were explored, by 32 diamond-drill holes totaling 11,649 feet during the periods from July 1943 to November 7, 1945, and from April 1944 to August 17, 1944. The drilling campaign disclosed a large area of mineralization. The ore, however, is apparently confined to long, narrow sheets. The indicated grade of the ore bodies blocked cut by the Bureau of Mines is 4.o8 percent zinc and 2.10 percent iron.

Jan 1, 1949

By Jon C. Volkwein

In This Chapter [Instruments for measuring dust How to calculate the amount of dust from a source How to get a valid concentration measurement Sampling to assess control technology effectiveness] When there is more than one source of dust, sampling may be required to find which dust sources are most significant. Then, efforts to reduce dust can be concentrated where they will have the most impact. This chapter explains how to perform dust source sampling. It describes two kinds of instruments that are available and discusses their limitations. It explains how environmental variables such as concentration gradients, dust dilution, and production changes can impact dust measurements. It also suggests practical ways to improve the validity of dust source measurements under adverse conditions, such as high-velocity airflow or the presence of water mist in the air. [Dust source sampling at coal mine longwalls and at tunnels is more complicated. Chapters 3 and 7 have more information on sampling in those circumstances.] TWO KINDS OF INSTRUMENTS FOR MEASURING DUST Gravimetric samplers. The conventional gravimetric sampler is a good device for measuring dust because it is the instrument used for compliance measurements. This dust sampler consists of an air pump, a small cyclone that separates out the respirable size fraction of the dust cloud, and a filter to collect the respirable dust. In coal mines, the Mine Safety and Health Administration (MSHA)-approved gravimetric sampler uses a 10-mm Dorr-Oliver cyclone operating at an airflow of 2.0 L/min [30 CFR78 74 (2002)]. A correction factor of 1.38 is applied to make the results consistent with the U.K. MRE sampler, the instrument on which the 2.0 mg/m3 coal dust standard is based.

Jan 6, 2003

By James V. Kelly

During the winter of 1946 and the spring of 1947, the Bureau of Mines conducted an investigation and drilling program in the vicinity of the village of Fairplay, Wis. Fifteen diamond drill holes totaling 2,457.6 feet of bore were completed. This work was part of a general study of the zinc-producing area of southwestern Wisconsin and had the particular purpose of investigating a structural trend, determined by the Federal Geological Survey, in an area some distance from known ore bodies or active mines.

Jan 1, 1948

By A. L. Engel

As a part of the program of the Rare and. Precious Metals Experiment Station, Reno, Nev., in connection with investigations of treatment methods for precious and precious-base metal ores, to further conservation and recovery of precious and base metals, tests Were made on samples from the Buzzard Mine, located in the vicinity of Placerville, Calif. These samples represented ore exposed during previous development work, in tunnels and a shaft on the property, including highly oxidized material from the surface zone and sulfide ores from depths of 150 to 300 feet. The surface samples contained little base metal and only enough gold 80 that economic exploitation of them would depend on development of a large tonnage of ore, low-cost mining methods, and satisfactory treatment methods. The sulfide samples were valuable enough to warrant further exploration and development and, if present in suitable tonnage, the installation of a treatment plant for recovery of both precious and base metals. The oxidized surface-zone samples carried 0.11 to 0.14 ounce gold per ton. Standard amalgamation and flotation tests of these samples gave low recoveries. Standard cyanidation tests indicated high consumption of lime and cyanide and gold extraction of 79.4 and 82.7 percent. Water-leaching the ore after crushing to minus 10-mesh improved cyanidation considerably. Ex-tractions of 82.7 to 85.8 percent were obtainec1 with lime consumption of 6 to 7 pounds per ton of ore and cyanide consumptions of 1 to 4 pounds. Grinding the samples to minus 200-mesh followed by water-leaching and cyanidation gave improved extractions of 91-92 percent of the gold, but with slightly increased consumptions of lime and cyanide.

Jan 1, 1949

By E. L. Garton

Bureau of Mines routine crude-oil analyses of 88 samples from 60 fields are presented in this report. Similar analyses from other fields in California have been published in previous reports listed in the appendix, page 52. Yearly production of crude oil in California and the percentage of United States production represented by California production for 1948-54 are given in table 1. [ ] Analyses in this report are of samples from the fields listed in table 2, with production data for 1953, cumulative production through 1953, and year of discovery of each field. Information regarding the source and general characteristics of the samples is included in table 3 with a summary of analytical and computed data.

Jan 1, 1956

By C. H. Herty, J. K. Gaines

"Nearly every piece of electrical equipment used in mines ""breathes."" In other words, motors, controllers, rheostats, switches, and other similar equipment, even though encased in seemingly tight compartments, breathe in the atmosphere that surrounds them.As the apparatus is used, the temperature of metallic parts is changed generally in positive direction through the heat by friction and the heat due to the electric current. When the apparatus is idle it gradually cools down to the temperature of the surrounding atmosphere.This increase of temperature during operation and return to normal temperature when operation stops alternately raises and lowers the temperature of the atmosphere within the compartments which, in strict accordance with Charles' law -T = VT1 V'will expand or contract in proportion to any given temperature change.As compartments are not gas-tight, such expansion and contraction will force the atmosphere out of the compartment =on expansion and suck the surround¬ing atmosphere into the compartment during contraction, hence the term ""breathing.""Investigators of explosion-proof equipment have recognized that such an interchange would take place and have designed their equipment to safeguard possible explosions within the compartments."

Jul 1, 1927

By V. E. Edlund

As part of its efforts to devise new and improved methods for recovering lithium from unconventional resources , the Bureau of Mines investigated a lime -gypsum- roast , water- leach technique for processing lithiumenriched ( 0.01-0.68 pct Li ) clays . This report presents the results of a study of the technical feasibility of extracting lithium from raw material representative of clay beds associated with the McDermitt Caldera complex in Nevada and Oregon . prepared from water used Pellets suitable for bench-scale roasting studies were mixtures of minus 200 -mesh clay , limestone , and gypsum , with as the pelletizing agent . Roasting pelletized charges at 900 ° to 1,000° C temperatures for 1- to 4-h periods produced calcines that leached readily , yielding water - soluble lithium sulfate ( Li₂SO4 ) . A 5-3-3 ( weight ratio ) mix of clay , limestone , and gypsum produced calcines with the best leaching characteristics . More than 91 pct of the contained lithium was extracted from pelletized mix batches roasted in covered refractory boats . Lithium recovery decreased to about 87 pct when the mix was roasted under dynamic conditions in a gas - fired rotary furnace . A reaction mechanism was postulated which indicated that dilution and loss of SO2 and oxygen in the combustion exhaust adversely affected the leachability of the dynamically roasted calcine .

Jan 1, 1983

Develop an inexpensive, reliable means of quickly detecting and locating trapped miners in underground coal mines, particularly after a mine accident. The Limitations Although the Bureau of Mines has performed extensive research on the use of electromagnetics for locating trapped miners, much of its research trends toward the development of long-range systems designed to locate an underground transmitter from the surface. Such location systems are beneficial; however, there are several limitations regarding their use. Two limitations are weight and cost of the equipment. Most long-range detection systems would be too heavy and cumbersome to be accepted by miners as part of their daily protective equipment. Since such long-range detection systems are usually expensive, it would not be economically feasible for every miner to be provided with a system.

Jan 1, 1984

By O. C. Blade

Consumption of Diesel fuel oil in the United States has increased very rapidly during recent years. At the present time approximately 5 percent of the crude oil refined in this country is said to be processed for this purpose. This figure represents approximately 20 percent of the total distillate-type fuel oils now being produced in the United States. One factor contributing greatly to the recent increase in consumption of Diesel fuel oil has been the conversion from steam locomotives to Diesel engines by a number of railroads. Other contributing factors are greFl.ter use of Diesel engine8 in buses, trucks, tractors, water craft, and stationary power plants. The growing importance of Diesel fuel oil has resulted in a need by the petroleum industry, engine manufacturers, and consumers for more information regarding the types and quality of Diesel fuels currently being marketed. To supply this information, the American Petroleum Institute and the Bureau of Mines, United states Department of the Interior, under a cooperative agreement, have conducted a survey of Diesel fuel all produced in refineries in this country during 1950. Under the agreements, samples of Diesel fuel oil, representative of actual shipments, were analyzed by the manufacturers in accordance with instructions issued by the Fuel Survey Panel of the Automotive Research Committee of the American Petroleum Institute. Results of the analyses were transmitted to the Bureau of Mines, and that agency has studied the data and compiled them by groups in comparable form as shown in the tables of this report.

Jan 1, 1950

By R. L. Brown, H. G. Berger, E. F. Pohlman

"The Bureau of Mines in cooperation with the American Gas Association investigating the relation of properties of gas oils to the gum-forming properties of carbureted water gas. The present report deals with the effects of operating practice on the composition of the light oils from carbureted water gas. A general outline of the gummy meter problem has been presented in a previous paper.*Carbureted water gas is a mixture roughly of 80 per cent water gas by volume and 20 per cent oil gas. The latter, though small in relative volume, supplies more than half of the heating value of the gas under the present-day standard. Therefore, it is logical that the oil used in the carbureting process and the operating practices involved should be subjected to scientific study. Many investigations***** bearing on the aspects considered in this paper have been carried out in the past."

Oct 1, 1923

By S. Ralph Austin

This Bureau of Mines investigation determined the effects of so-called annealing at high temperatures on radon-222 emanation from domestic uranium ores. Concurrently, a method was developed for closely estimating the emanation coefficients of hot samples from measurements of their gamma activity after cooling. Emanation coefficients of 102 samples from 14 domestic areas of past, present, and possible future uranium production were investigated using modifications of the closed-can, gamma-only assay method at and after cooling from 100° to 1,000° C. True annealing probably does not occur below 500° C. In limited investigations at 500° C and above, effects of annealing are masked by the effects of other parameters. Emanation is commonly less at one or more of the steps investigated in the 100° to 500° C range than before heating. This decrease is tentatively attributed to water loss at temperatures dependent upon the minerals present. The average sample emanates least at 300° C; emanation increases with higher temperatures to at least 900° C. Emanation decreases sharply on cooling, but it is partially restored by prolonged exposure to the atmosphere at room temperature. Higher than average emanation of coffinite ores at 500° C and above may be related to destruction of the coffinite crystal structure.

Jan 1, 1979

By Thomas H. Dubaniewicz, Gerald R. Cucci, Gregory M. Green, Kenneth L. Cashdollar

New types of industrial instruments use fiber-coupled law energy to power remote serum. Fiber-optic based instruments are useful in classified (hazardous) locations found in many industrial plants because the fiber provides a natural barrier against accidental electrical discharge into potentially explosive atmospheres. However, current safety standards do not cover the use of laser-powered fiber-optic instruments in potentially explosive environments such as found in coal mines. The U. S. Bureau of Mines began an investigation of laser-powered fiber-optic instruments in explosive atmospheres in support of the standards-making process. A commercial fiber-optic interface system, modified to sin relate several worst-case operating conditions, ignited explosive hydrogen-air mixtures. Worst-am simulations consisted of disabling a safety shutoff feature, operating the laser at significantly higher powers than intended for normal operations, and cleaving fiber-optic connections to direct laser energy onto selected absorptive materials. At the highest power level available, the fiber-optic interface system did not ignite selected methane-air mixtures. The obtained data should prove useful in establishing appropriate safety standards.

By James E. Cairelli

The NASA Lewis Research Center, under U.S. Bureau of Mines program direction, performed an assessment of alternative mobile power sources for mining applications. A wide variety of heat engines and energy systems was initially examined to ascertain which could be considered as potential alternatives to presently used power systems. The present mobile power systems are electrical trailing cable, electrical battery, and diesel - with diesel being largely limited in the United States to noncoal mines. Each candidate power source was evaluated in terms, of the following requirements: (1) Ability to achieve the duty cycle (2) Ability to meet Government regulations (MSHA certification) (3) Availability (production readiness) (4) Market availability (5) Packaging capability An initial screening reduced the list of candidates to the following: (1) Diesel (2) Stirling (3) Gas turbine (4) Rankine (steam) (5) Advanced electric (batteries) (6) Mechanical energy storage (flywheel) (7) Use of hydrogen evolved from metal hydrides This list of candidates was divided into two classes of alternative power sources for mining applications - heat engines and energy storage systems. A summary of each class follows.

Jan 1, 1981

By J. L. Reuss

The Bureau of Mines investigated the technical feasibility of smelting copper concentrates containing chalcocite (Cu2S) and native copper using nonpyritic sulfur-bearing materials to aid matte formation. The procedure consisted of combining various proportions of commercial chalcocite concentrate, smelter slag, fluxes, and matte-forming constituents to produce charges of comparable compositions. The mixtures were charged in fire-clay crucibles and smelted in an induction furnace at 1,300° C. The research proved that either sulfur or gypsum can replace pyrite as a matte-forming material, and that gypsum produces an exceptionally high-grade copper matte. The addition of small quantities of metallic iron to the nonpyritic smelting charge furthers the removal of sulfur, improves the recovery of copper, and makes it possible to utilize gypsum as the exclusive flux and matte-forming ingredient, thereby eliminating the necessity of adding limestone.

Jan 1, 1968