Search Documents

By M. J. Beus

The U.S. Bureau of Mines is conducting investigations to improve design methods for mining volcano-genic massive-sulfide (VMS) type deposits in environmentally sensitive regions. This study was conducted at the Greens Creek Mine, which is typical of many VMS-type deposits throughout southeast Alaska, and served as a case history for computer modeling and structural analysis. Results indicated that the finite-element design method provided reasonable comparisons with both the anticipated regional stress regime and the measured deformational response of the underground accessways. Investigators concluded that reasonable accuracy can be expected for stability analyses of proposed mine design scenarios at this mine using the results of this preliminary study.

Jan 1, 2010

By J. H. Bilbrey

A recording thermobalance ,vas used to determine the rates of oxidation of mol-ten tin over the temperature range 550°-900° C. Oxidation rates were found to vary widely for a given temperature, as previously reported by other investigators. 1 X-ray diffraction data indicated that the probable cause of these variations was the development of preferred orientations in the crystals forming the oxide film. No reasons for the differences in degree of preferred orientation were discovered. For relating the weight of the oxide formed (w) to the time of oxidation (t) an equation of the form wn = kt was found to best represent the experimental data. INTRODUCTION In the course of conducting investigations on the feasibility of using selective oxidation techniques for the purification of various metals in the molten state it was soon discovered that data on the oxidation of molten metals and alloys were very scarce. In contrast to the many hundreds of publications on the oxidation of metals in the solid state there are relatively few articles on the rates of molten-metal oxidation. In view of this scarcity of data, it was decided to institute a series of investigations into the oxidation processes of molten nonferrous metals and alloys with the expectation that the information derived could be put to practical use in developing and improving refining processes based on selective oxidation. This report is the first of a series in which oxidation data for molten nonferrous metals and alloys are presented.

Jan 1, 1955

By Donald E. Redmon

Industrial engineering departments perform staff duties and are most effective when sincerely supported by management. In accordance with the needs and desires of the mining companies involved, various industrial engineering functions have been adopted widely at western metal mines during the period 1950-60. Newly organized departments usually conduct method and equipment studies, work-measurement programs, and establish and maintain production standards. Supervisor-training programs and courses are effective in showing the relationship between supervisory responsibility and the purpose for which industrial engineering is practiced. Industrial engineering staffs of western metal mines are composed predominantly of personnel from within the companies. Experienced industrial engineers, not necessarily experienced in mining, frequently are hired by a company to help establish the department. Management consultants frequently are called upon to advise management and instruct department personnel in industrial engineering practices. Some departments have developed satisfactory industrial engineering programs without benefit of formal industrial engineering training or advice.

Jan 1, 1962

By R. C. Hickman

"INTRODUCTION .As part of its spot drilling program, the Bureau of Mines core-drilled seven holes on the Alexander and Barber properties in Spartanburg County, S. C.Extensive surface float and outcrops of sillimanite schist on these properties appeared to justify drilling, which did not prove satisfactory, however, owing to the spotty occurrence of the schist bodies and the poor core recovery in the decomposed schist.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, Oliver C. Ralston, chief, analyzes samples and performs beneficiation tests.This project was under the immediate supervision of Mitchell H. Kline, chief, Raleigh Division, Mining Branch, Bureau of Mines.LOCATIONThe Alexander and. Barber properties are in the southern part of Spartanburg County, S. C. The Alexander property is about 5 miles cast of Woodruff. It is reached from Woodruff by driving east 5 miles on a macadam road to the intersection with an unsurfaced road near Unity Church. The farm house on the property is 0.4 mile north on this road. The sillimanite outcrop is in a field approximately 1,200 feet east of the farm house. The Barber property is about 2 miles north along the unsurfaced road that passes the Alexander property."

Sep 1, 1947

By H. L. Anthony, A. C. Richardson, G. D. Coe

"INTRODUCTION The Warrior View mine of the Seaboard Coal Corporation is located in Tuscaloosa County on the Warrior River about 14 miles northeast of Tuscaloosa, Ala. The Brookwood bed at this point yields a coal with fair coking qualities, and the product from neighboring mines on this bed has been used for the manufacture of blast furnace coke. The output of the Warrior View mine, however, is used exclusively for domestic and steam-raising purposes.This paper continues the series° of reports on the washability of Alabama coals which are based upon the study of coal preparation in Alabama now being conducted by the U. S. Bureau of Mines and the University of Alabama with the cooperation of the different coal mining companies. This paper contains screen-sizing and float-and-sink tests of a representative sample of run-of-mine coal, and flakiness and crushing tests on certain sizes.Published information on the Brookwood bed is very meager. Fieldner6 gives the proximate and ultimate analyses for a number of seam samples taken from representative mines working this bed. Gandrud and Britton7 show sections of this bed taken at Searles, Ala. They also give the specific gravities of the coal, the bone, and the shale partings.Table 1 give the proximate and ultimate analyses for the 3/4 to 3/16 inch size of raw coal. Table 2 gives the sulphur content and the ash fusibility temperatures of the float-and-sink fractions for this same size. The character of the coal is very uniform throughout the range of sizes produced and, as it was not convenient to have these analyses on all sizes, this size was chosen as being representative of the coal. From the information available it is evident that the coal preparation problem is restricted to one of ash reduction.SAMPLING AT THE MINEAt the Warrior View mine the run-of-mine coal is dumped from the mine cars upon a 3-inch grizzly. The oversize is crushed in rolls set at 24 inches and joins the undersize before being elevated to the raw-coal bin ahead of the jig. The sample was caught at the point where elevates discharges into the raw-coal bin, by taking a proportional amount of the coal at 10-minute intervals over the period of a day's run, The total sample amounting to 2.7 tons was shipped to the laboratory at Tuscaloosa for the washability studies."

May 1, 1932

To provide operators of large-opening mines with a ventilation planning tool that will help them develop a healthier, safer, and more efficient ventilation system in the underground workplace.

Jan 3, 2006

By Robert Stefanko

The following tables contain the average, maximum and minimum power parameter levels for several mining machines. Power factor is listed only for defined transducer output regions. The reasons for the undefined areas are provided in the Instrumentation Chapter. Several maximum voltage drops are included, and are computed from the no load line-to-line voltage: Again, the drops are from measurements at the low side of the load center. The machines are: Continuous Miners; F6A Alpine 76AM Jeffrey (d-c) 8CM Joy 8CM (10CM) Joy 9CM-2AH Joy loam Joy CU-43-2H Joy 2 each CM26H Lee-Norse CM28E Lee-Norse Shuttle Cars; 18SC Joy 48S Torkar (a-c) 2 - 10SC Joys input to rectifier 2 - 16SC Joys input to rectifier

Jan 1, 1973

By M. J. Dailey

This paper is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The property of the Silver King Coalition Mines Co. is situated in the western past of the Park City mining district, Utah, about 1 ½ miles southwest of the town of Park City, The elevation at the collar of the main shaft is 8,137 feet above sea-level.

Jan 1, 1930

By C. Melvin Lepper

High-resolution shallow seismic reflection methods are being used by the Bureau of Mines to map underground geologic features in coal mines. These features include faults, channel sand, washouts, rolls, and steep dips. The seismic method is proving useful for locating all of these at reasonable cost and with better definition than available with drill programs alone. This report provides a capsule description of the techniques and their application to mine planning.

Jan 1, 1976

By Launa Mallett, Charles Vaught, Michael Brnich, ROBERT PETERS

Interviews of 48 miners who escaped underground coal mine fires revealed that none of them had ever, before that incident, worn their self-contained self-rescuer (SCSR) either in training or in a real emergency. Consequently, they were ill-prepared to use this emergency breathing apparatus. One persistent problem stemmed from the fact that miners had no notion of breathing resistance, nor of the fact that it would get more difficult to breathe the longer they wore their device. As a result, many of those who were interviewed had simply removed their mouthpieces and breathed ambient air. This is obviously behavior that should be trained out of the workforce. Unfortunately, because of high costs and difficult logistics, miner training is unlikely to ever include donning and wearing an apparatus on a regular basis. In order to give workers a better idea of what to expect from their devices, therefore, the National Institute for Occupational Safety and Health researchers developed a tabletop (paper and pencil) simulation based upon actual predicaments evacuees had reported encountering. The simulation is designed to emphasize important points related to donning and wearing a self-contained self-rescuer in a mine fire escape, and, by doing so, to bring miners' expectations more in line with what their actual experiences would be. The simulation was field tested in six training classes at three different mining operations. In all, 99 individuals were involved in completing the exercise and rating its properties. In their ratings 88% of the respondents indicated they thought the scenario could definitely happen in real life, and over 80% agreed they had learned something new. From the field test data it was concluded that the simulation had authenticity and potential value as a teaching tool. The simulation was therefore used in a pre-test/post-test control group experiment to determine whether it led to improvements in miners' scores on a true-false test of their SCSR's functional capabilities and proper usage. Eighty-three miners were included in this part of the study. As expected, miners who had participated in the training exercise scored significantly higher on their post-test than miners who had not.

By C. R. Summers, J. N. Murphy

In response to the Coal Mine Health and Safety Act of 1969, mandatory noise standards have been developed that specify time-noise limits of mine personnel exposure. Most affected by elevated noise levels is the pneumatic roof bolter operator, both in terms of levels near or in excess of 115 dbA and in terms of length of exposure. Therefore, the principal emphasis of this Bureau of Mines report is on pneumatic drill noise control. It is not the intent of this report to suggest any drill redesign; instead, methods are suggested to reduce the noise level by complementing existing machines. An integral muffler system and a separate muffler system were tested in an attempt to lower pneurnaric drill noise levels. Pneumatic drills, when new, operate at about 115 dbA when drilling in sandstone. Using the drill muffler systems, it was possible to decrease the noise level of a 115 -dbA s rope drill to approximately 100 dbA.

Jan 1, 1974

By R. V. Petrella

The flash induced combustion of Sewell and Pittsburgh coals was studied in air and in oxygen. The primary decomposition and combustion processes occur within the first 300 ~sec in oxygen and slightly later in air. Strong absorption spectra of CN and OH are indicative of the decomposition and combustion processes, respectively. Kinetic spectroscopy and combustion product analyses indicate that only about 35% of the coal dust is consumed in the explosive combustion which takes place in several (1-5) distinct but similar steps. The combustion-modifying effects of (NH4)2HP04, NH4H2P04, KHC03 and Rock Dust were studied in the 1-20 wt % range in coal dust flash com-busted in air and oxygen. The study reported herein shows Rock Dust to be the most efficient coal combustion inhibitor. KHC03 is the least effective agent, with the phosphate salts showing marginal effectiveness.

Jan 1, 1976

By G. R. Strimbeck

The Federal Bureau of Mines has been developing processes for producing synthesis gas directly from coal, oxygen, and superheated steam. An atmospheric-pressure pilot plant was constructed and operated to: 1. Determine the operability of the plant for gasifying coals of different ranks under various operating conditions. Listed in decreasing order of rank, these coals included a Pennsylvania anthracite, a bituminous A coal from the Sewickley bed, West Virginia, and a subbituminous C coal mined in the Lake de Smet region of Wyoming. 2. Determine the effect of varying operating conditions on: (a) Standard cubic feet (std.c.f.) of oxygen and pounds of coal of different rank required to make M std.c.f. of product gas (carbon monoxide plus hydrogen); (b) carbon gasified, percent; (c) exit-gas temperature, degrees F.; and (d) heat loss, B.t.u. per pound coal. 3. Compare the gasification characteristics, indicated in item 2, of coals of different rank: Bituminous A, anthracite, and subbiturninous C. 4. Determine the concentration of dust in the gases produced and the efficiency of dust removal, and investigate the relation between the sulfur content in the coals gasified and the gases produced.

Jan 1, 1960

By Richard L. Rains

The Bureau of Mines conducted a mineral investigation of the 29,000-acre Dixie Summit area near Elk City, Idaho, during the summer of 1989. At the Petsite mine a marginally economic, identified resource of 4.9 million tons with an average grade of 0.023 ounces gold per ton was delineated. Possible resources of gold, along with silver, copper, lead, and zinc, occur in at least eight other lode deposits. Placer gold may be recoverable by recreational-sized suction dredges in some stream drainages, Five lode mines in the study area have produced over 5,516 ounces of gold (placer gold production was not recorded), 4,757 troy ounces of sliver, 36,746 pounds of lead, and 3,800 pounds of copper. Current mining claims in or adjacent to the study area total 460 lode and 70 placer claims. There are two patented lode claims within the Dixie Summit study area.

Jan 1, 1991

By Thomas M. Barczak

This U.S. Bureau of Mines report is intended to assist coal mine operators in the selection of longwall supports by providing advanced guidelines for performance testing and standardized test documentation to facilitate support comparisons. These advanced guidelines culminate in a series of proposed tests to evaluate (1) support resistance characteristics, (2) stiffness characteristics, (3) leg mechanics, (4) stability, (5) load transfer mechanics, and (6) structural integrity. The Bureau has conducted extensive studies on shield mechanics to identify boundary conditions that induce loading in support components, which is often not included in current testing techniques. This report discusses influential parameters that affect support behavior and provides insight into how components are loaded and what conditions produce the most severe loading. Testing philosophies and techniques in both active and static frames are discussed. Proper methods for determining support resistance are described and instrumentation requirements for advanced performance testing are provided.

Jan 1, 1989

By J. J. Forbes

The activities of the Bureau of Mines include the development and testing of self-contained oxygen breathing apparatus and other devices for respiratory protection, the development and tasting of devices for detecting dangerous or noxious mine atmospheres, and the training of men in the mineral industries in the use and care of this equipment to enable them to render effective service in mine rescue and recovery operations following mine fires and explosions, or under other conditions where irrespirable gases may be found in mines or mining plants. The first use of self-contained oxygen breathing apparatus for com- bating mine fires and explosions in the United States dates back about 30 years. Previous to that time, exploration for any distance ahead of fresh air was virtually impossible without great risk to life; moreover, the men called upon to render service at mine disasters were not well-versed in the properties and physiological effects of gases likely to be encountered. It was also impossible to work ahead of fresh air to restore ventilation, and if many stoppings were blown out by an explosion, air had to be introduced into whole areas or sections at once without knowledge of the conditions ahead; moving an explosive mixture of methane and air over live fire had to

Jan 1, 1938

By A. L. Peyton

The Brewer mine, near Jefferson, Chesterfield County, S. C., was originally operated as a gold mine. As late as 1890 this mine was reported to have been one of the large gold producers in the southeast. Occurrence of topaz on the Brewer property was not reported until 1935, when it was discovered, by Parks3/ and Parks of the Federal Geological Survey while they were investigating gold deposits in the Piedmont province.

Jan 1, 1953

By E. M. SEELEY, F. S. LOTT

Expansion in total capacity of the natural-gasoline industry.to produce light products continued in 1944 and 1945. The average rate of gain, however, was reduced to about 6 percent annually from over 9 percent in the preceding 4-year period. New facilities at cycle plants again accounted for most of the increase in productive capacity. Between January 1, 1944, and January 1, 1946, the number of cycle plants increased from 32 to 37 and their total capacity from 3,278 thousand gallons daily to 4,848 thousand (48 percent). Capacity of all other plants in the industry increased in the same period from 12,735 thousand gallons daily to 13,080 thousand, or only 3 percent. The capacity of the average plant increased to 28,600 gallons a day from 24,400 gallons on January 1, 1944, continuing the established trend. The average capacity of cycle plants increased to 131,000 gallons a day from 102,400 gallons, and the average capacity of all other natural-gasoline plants increased to 22,200 gallons a day from 20,400 gallons. Although the number of plants increased in only three States in the 2-year period (Texas, Okla- homa, and Arkansas), the total capacity of plants increased in eight States. A further decline of 29 reduced the total number of plants to 626 on January 1, 1946. Compared with 10 years earlier, gasoline plants were more numerous in only 4 States: Texas (48 more), New Mexico (7 more), Arkansas (2 more), and Louisiana (1 more). The largest declines, in order, were in Oklahoma, Illinois, Pennsylvania, West Virginia, and California. The number of plants with fractionating equipment for separating the liquefied gases from heavier fractions was 202 on January 1, 1946 and 182 2 years earlier. The principal changes in number and capacity of shut-down plants were an increase in Texas and a decrease in California. Shut-down natural-gaso- line plants are usually among the smallest units in their vicinity.

Apr 1, 1947

By Margaret R. Egan

A series of experiments were undertaken by the Bureau of Mines to determine the emission products of several types of conveyor belting and other combustible materials found in mines. These experiments were conducted under intermediate-scale, simulated mine conditions to determine smoke characteristics and gas concentrations. From these determinations, heat-release rates, particle sizes, obscuration rates, combustion yields, and production constants were calculated. Three types of belts were investigated: chloroprene, also known as neoprene (NP); polyvinyl chloride (PVC); and styrene-butadiene rubber (SBR). The belts were designated as ignitable or self-extinguishing depending on the length of the burning time and the subsequent combustion products. Under these experimental conditions, the SBR belts were the easiest to ignite. The PVC and NP belts tended to self- extinguish within a few minutes after ignition, but were still capable of maintaining a brief flaming period. These conveyor belt combustion results are compared with previous analyses of wood, transformer fluid, and coal fires. Together they form a data base by which findings from future experiments with other mine combustibles can be compared.

Jan 1, 1988

By J. W. Horne

The United States Bureau of Mines in cooperation with the State of Colorado at the University of Colorado has conducted experiments to determine the amount and composition of the non-condensable gases evolved when crude shale oil is distilled under pressure. Hydrogen sulphide is one of the components found in the complex mixture of Gases produced by the distillation of shale oil under pressure. This paper deals with the apparatus and method used in determining the amount of hydrogen sulphide evolved in the laboratory experimental cracking stills. The study required a complete extraction of all the hydrogen sulphide from the gas stream after it left the water-cooled distillate condensers and before the gas stream entered the charcoal absorber for removing the light naphtha. In devising the method it was necessary to take into account a constant variation of velocity, pressure, and percentage of sulphide in the total gas stream coming from the still. Ordinarily, the quantitative determination of hydrogen sulphide in gas is made by analyzing small samples taken at regular intervals. This estimation can be accomplished by use of the Bunts gas burette as modified by Tutriler, or by a similar method. In the industries where the flow of gas is constant and of uniform composition, this practice is sufficiently accurate for plant control. For experimental work where many variables have to be taken into consideration, as in the case at band; these methods are not applicable.

Jan 1, 1931