Search Documents

By C. R. Stephan, N. B. Greninger, S. J. Luzik

The U.S. Bureau of Mines conducted explosion tests on various full-scale cementitious bulkheads used in abandoned mine areas to evaluate the ability of the bulkheads to withstand gas explosion over-pressures of 20 psig. Tests were performed on 120-ft2 solid-concrete-block seals of varying thicknesses and designs. Of the seven solid-concrete-block seals tested, only the standard-type seal, having a 16-in thickness, keyed at the floor and ribs, all joints mortared, wedged at the roof, and a center pilaster, maintained its integrity when subjected to a 20-psig pressure wave. After being subjected to repeated explosions, the standard seal only showed a small hairline crack and had an air leakage of 87 ft3/min at a pressure differential of 1 in H2O. Tests were performed on cementitious foam seals of varying thicknesses and compressive strengths. Explosion tests have shown that 200-psi strength, 4- and 8-ft-thick seals can withstand a 20-psig pressure wave. At a pressure differential of 1 in H20, no air leakage was detected through the 200-psi, 8-ft-thick foam seal.

Jan 1, 1991

By G. R. Hopkins

[ ]

Jan 1, 1927

By Nancy Potts, M. G. Barker, W. C. Holliman

"SUMMARYThis report on the characteristics of commercial aviation gasolines presents compilations of inspection test data furnished on their products by manufacturers of commercial grades of aviation gasoline, and special data obtained in Bureau of Mines laboratories on samples of these gasolines. Data and physical samples for the survey were submitted by 15 manufacturers on 18 grade 80, 21 grade 91/98, 22 grade 100/130, end 10 grade 115/145 aviation fuels.The inspection test data supplied by the participating manufacturers consist of octane and performance numbers, tetraethyllead content, dye color, and other characteristics usually listed in aviation gasoline specifications, such as AN-F-48a or ASTM Designation D910-47T. These data are tabulated and averaged by grades in tables 1 through 4 and, as reported, meet the AN-F-48a and similar specifications with a few exceptions. Two grade 80 gasolines show a lean-mixture octane rating slightly below 80.0, and 91/98 grade fuel shows a lean-mixture rating of 90.9 and a rich-mixture rating of 97.5, two 100/130 grade gasolines have a rich-mixture performance number slightly below 130.0, and one 115/145 grade gasoline shows a rich-mixture performance number of 144.5. However, octane and performance number averages are above the mini¬mum requirements for each grade. Tetraethyllead content in the 91/98 and 100/ 130 grades generally is above the maximum outlined in these specifications, whereas dye color for each of the four grades, with the exception of two gasolines in grades 80 and 100/130, is that designated for the particular grade. Distillation requirements, with a few exceptions at individual points, are met by gasolines of all grades. Reid-vapor-pressure, copper-dish-residue, heat-of-combustion or aniline-gravity-constant, freezing-point, and copper-strip-corrosion requirements are met by all gasolines so far as reported. No data for some of these tests wore submitted on a few of the gasolines. One gasoline, grade 115/145, shows a sulfur content greater than the specified maximum."

May 1, 1948

By S. H. Lorain

Shortly after the Strategic Minerals Act of 1939 we passed by Congress, the Bureau of Mines was authorized to begin a program of investigation of domestic sources of strategic minerals. Since World War I, the Philipsburg district had been virtually the only one in the United States that was producing manganese on a commercial scale. Consequently, the district was among the first to he investigated. During the summer of 1939, the Geological Survey mapped the geology and ore deposits of the district. In late July 1939 the writer examined the district for the Bureau of Mines. On the basis of this examination and of the work performed by the Geological Survey, the Bureau of Mines diamond-drilled at several properties in the district during the summer of 1940. This report reviews the mining history and geology of the district, and presents the factual data obtained by diamond drilling.

Jan 1, 1950

By Robert W. Geehan

"INTRODUCTION The Bureau of Mines has been investigating deposits of critical and essential minerals in the United States since 1939. Many of the mines were developed.A preliminary examination of the Sultan mine was made in January 1945 by the author, who recommended investigation by drifting and crosscutting. The Bureau conducted a project at the mine from April to June 1946. Claims investigated are in sec. 20, T. 25 S., R. 58E., Mount Diablo base and meridian, in southern Clark County, Nev., about 7 miles southwest of Good-springs.The Sultan mine has been an intermittent producer of zinc-lead-silver ore since 1910. During World War II, ore was shipped to the Government stock pile at Jean, Nev., and to the International Smelting& Refining Co.'s smelter near Salt Lake City, Utah. Throughout the past year, ore has been milled and the concentrates have been shipped to the smelter."

Sep 1, 1947

By E. D. Gardner

About 300 tons of gold ore per week was being produced in February 1934 by Thomas D, Herron and Con Laster from the old lake Superior and Arizona workings; the ground was leased from the Magma Copper Co. The workings adjoined but were not a part of the Magma mine. The lessees had been employees of the Magma Copper Co, at the time the Magma closed down for the summer of 1932. Work on the lease began in July 1932 on an exposure of $2-per-ton ore disclosed in a drift; after a few hand-drilled rounds were blasted the gold content increased to about $30 per ton. Extensive sampling by pannings elsewhere of exposed portions of the vein indicated that other ore shoots existed. The last work previously done in the mine was during the World War, when lessees mined a number of small shoots of copper ore. In some of the stapes the copper miners had left a quartzose streak on the hanging wall that carried $15 per ton of gold. This material did not look as if it cried values and evidently never had been sampled. The first shipment of gold ore was made on September 28, 1932. Up to April 1, 1933, 3,778 tons had been shipped and from September 1, 1933, to January 31, 1934, 3,125 tons.

Jan 1, 1934

By M. G. Zabetakis

At ordinary temperatures and pressures methyl ethyl ketone (MEK)-air mixtures containing between 2.0 and 11 vol.-pct. MEK and methyl isobutyl ketone (MIBK)-air mixtures containing between 1.5 and 7.5 vol.-pct. MIBK are flammable. However, MEK-bromochloromethane (BCM)-air mixtures containing at least 6.2 vol.-pct. BCM and MIBK-BCM-air mixtures containing at least 7.0 vol.-pct. BCM are nonflammable. Also, MEK-BCM-air and MIBK-BCM-air mixtures containing less than 18.7 vol.-pct. oxygen are nonflammable. To assure the formation of nonflammable mixtures when mixed with air, MEK-BCM vapor mixtures must contain at least 1.6 vol. BCM per volume MEK, and MIBK-BCM vapor mixtures must contain at least 2.8 vol. BCM per volume of MIBK; these quantities of BCM would be produced by liquid mixtures containing 55 vol.-pct. BCM in the first case and 60 vol.-pct. in the second. An MIBK-BCM-trimethylene chlorobromide mixture containing equal volumes of each liquid forms nonflammable mixtures with air at ordinary temperatures and pressures. The same is true of a liquid mixture containing 34.6 pct. (liquid volume) BCM, 34.b pct. perchloroethylene, 15.4 pct. MIBK, 7.7 pct. toluene, 3.85 pct. ethyl amyl ketone, and 3.85 pct. trimethylene bromide.

Jan 1, 1960

Provide a simple and effective means of measuring mining-induced pressure changes in coal mine roof and pillars. Approach Develop a reliable, easy to fabricate and install borehole instrument which measures mining-induced pressure changes in pillars and in the mine roof. Ground pressures are monitored through use of aluminum platens coupled with d copper flat jack. How It Works The Bureau's instrument measures mining-induced pressure changes by transmitting strata pressure through the aluminum platens to an oil-filled borehole platened flat jack (BPF). Pressure in the flat jack is displayed on a gage located outside of the borehole. The instrument is in-stalled in the borehole by inflating the flat jack using a hand-held hydraulic pump. In addition, the platens have been designed to allow up to three BPFs to be installed in a single borehole, thus permitting pressure change measurements in more than one direction from a single borehole. Installation pressure is calculated on the basis of the estimated pressure exerted by the overburden and the percent of recovery after intial mining has

Jan 1, 1986

By G. T. Fisher

The U.S. Bureau of Mines conducted research on calcium ferrite slags to determine the distribution of Pb and minor elements (Ag, Cd, Zn, and Co) between Pb bullion and slag. These fundamental data are required to evaluate nonferrous smelting with calcium ferrite slags as a substitute for conventional iron silicate slags. Determinations were made in 25-cm3-capacity MgO crucibles at 1,250° C for 2 h in a CO-CO2 atmosphere with an O2 potential that would retard the formation of magnetite. Calcium ferrite slag composition variables studied were from 16 to 32 wt pct CaO in 2-pct increments and Si02 ranging from 1 to 5 wt pct in 1-pct increments with equal additions of MgO. For all compositions studied, the retention of Pb in the calcium ferrite slag was less than 1 wt pct, which compares favorably to about 6 wt pct Pb in conventional iron silicate slags used in smelting of Pb concentrates. Minor element distribution was insensitive to changes in slag composition in the range studied. However, slag composition had significant impact on the melting and fluidity of the slag.

Jan 1, 2010

By J. Koster

In the western United States occurs deposits of low-grade chromite which, when concentrated, may be reduced to ferrochromiun in electric furnaces that derive energy from dams and hydro plants now in course of construction. Montana ore was chosen for the experiments. A 1-ton sample contained 26 percent Cr203, 17 percent Fed, and 17 percent SiO2, plus other constituents, and the concentrates therefrom assayed 44 -percent Cr203, 23 percent FeO, and 0,79 per cent SiO2, Gravity concentration was found to be the best method. Ferrochromiums are of two grades - high-carbon with 66 to 70 percent chromium and 4-112 to 6 percent carbon and low-carbor with 67 to 72 percent chromium and 0.6 to 2 percent carbon. Both are made in electric furnaces that use anthracite as a reducer and suit-able fluxes. The concentrates mentioned mere smelted under different conditions, and it was concluded that domestic ore could be reduced with anthracite to produce a ferrochromium of S to 10 percent carbon content at yields of 90 percent without re-treating the slag. This carbon may be lowered to required proportion with calcium and silicon, but the former requires a great excess and the latter leaves an alloy high in silicon. INTRODUCTION Chromite occurs in several regions of the United States, but the known deposits of this mineral have not been large enough or high grade enough to permit them to compete under normal conditions with imported ores. There are numerous deposits of chrome ore along the West coast. These are generally conceded to be relatively small, although some were worked during the World War. There are some indications of a revival of interest in California chromites. Montana contains large chromite deposits in Stillwater and Sweetgrass Counties. The utilization of chromite for ferrochromium and. the manufacture of stainless steels is distinctly an electrometallurgical problem; consequently, a study of methods for treatment of chromite might pave the way for the establishment of new electrometallurgical industries in the Western States. This thought is supported by the cheap power that is soon to become available from the western dams, Farther, submarginal domestic chrome deposits might thus be turned into profitable producers.

Jan 1, 1936

By J. Koster

In the western United States occurs deposits of low-grade chromite which, when concentrated, may be reduced to ferrochromiun in electric furnaces that derive energy from dams and hydro plants now in course of construction. Montana ore was chosen for the experiments. A 1-ton sample contained 26 percent Cr203, 17 percent Fed, and 17 percent SiO2, plus other constituents, and the concentrates therefrom assayed 44 -percent Cr203, 23 percent FeO, and 0.79 per cent SiO2, Gravity concentration was found to be the best method. Ferrochromiums are of two grades - high-carbon with 66 to 70 percent chromium and 4-112 to 6 percent carbon and low-carbor with 67 to 72 percent chromium and 0.6 to 2 percent carbon. Both are made in electric furnaces that use anthracite as a reducer and suit-able fluxes. The concentrates mentioned mere smelted under different conditions, and it was concluded that domestic ore could be reduced with anthracite to produce a ferrochromium of S to 10 percent carbon content at yields of 90 percent without retreating the slag. This carbon may be lowered to required proportion with calcium and silicon, but the former requires a great excess and the latter leaves an alloy high in silicon. INTRODUCTION Chromite occurs in several regions of the United States, but the known deposits of this mineral have not been large enough or high grade enough to permit them to compete under normal conditions with imported ores. There are numerous deposits of chrome ore along the West coast. These are generally conceded to be relatively small, although some -were worked during the World War. There are some indications of a revival of interest in California chromites. Montana contains large chromite deposits in Stillwater and Sweetgrass Counties. The utilization of chromite for ferrochromium and. the manufacture of stainless steels is distinctly an electrometallurgical problem; consequently, a study of methods for treatment of chromite might pave the way for the establishment of new electrometallurgical industries in the Western States. This thought is supported by the cheap power that is soon to become available from the western dams. Farther, submarginal domestic chrome deposits might thus be turned into profitable producers.

Jan 1, 1936

By K. K. Kershner

To meet an increasing demand for high-purity cobalt, the Bureau of Mines has conducted investigations for producing this metal. Cobalt having a purity of 99.95 percent or higher is needed to determine heats of formation, corrosion resistances, phase diagrams, and other basic properties of the element and its compounds. This grade of cobalt may be used for preparing radioactive metal. As a result of its investigations a detailed procedure, which is of practical significance to the production of high-purity cobalt, has been developed by the Bureau for purifying cobalt solutions and for electrolytic deposition of the metal. Cobalt metal, which had a purity of 99.99 percent with reference to metallic contaminations, was deposited electrolytically. Qualitative spectrographic analysis showed only traces of calcium, copper, iron, magnesium, nickel, and zinc.

Jan 1, 1956

By J. R. Bartels

Operation of underground coal mine mobile equipment is usually done in a restricted workspace with reduced visibility. This work environment puts machine operators in awkward postures for tasks that require awareness of their surroundings and fast reactions to avoid hazardous situations. Using experienced equipment operators as a source, researchers conducted an investigation that developed a method to gather data on the needs and practices of machine operators while controlling the machine and the reasons for needing particular operational cues. The method used was an interview technique including a survey questionnaire and visual aids. The data gathered defined operator cues and work positions for the cutting and tramming phases of remote controlled continuous mining machines used in underground coal mines. Analysis techniques to determine which cues an operator sees from a variety of positions utilizing a computer simulation is shown to be potentially useful to the mining industry for design of work practices and workplace layout and could impact equipment design and selection for improved worker safety. Conclusions indicate that the survey was a good research tool to collect data and helped investigators understand important visual cues. Using this information, researchers were able to analyze the visual cues an operator can see from a given work position and posture.

Jan 1, 2009

By Marc T. Filigenzi

Two of the major ground control safety issues confronting underground mine operations today are shaft pillar stability and the failure of rock around active mine openings. Failure of a mine shaft can lead to the entrapment of workers. Failure of rock around active underground mine openings can lead to roof falls, which in turn can result in worker injuries and fatalities. Finite-element analysis has proven to be a reliable method for predicting stresses and displacements around underground mine openings. However, this is a complex and time-consuming technique and is not used as often as it could be in mine planning. The purpose of this paper is to demonstrate one technique developed at the Spokane Research Center that allows the user to create a finite-element model of a two-dimensional section of an underground mine in a relatively straightforward manner. This model is then used to calculate stresses, displacements, and safety factors around mine openings. With this information, mine planers can evaluate the stability of mine openings as well as the stability of pillars and mine shafts. This analysis will help develop mining sequences and layouts that minimize stresses in that section of the mine. This, in turn, should minimize the occurrence of shaft failure, roof falls, and other hazards associated with underground mining.

By Charles Vaught, Michael J. Brnich, Henry P. Cole, John V. Haley, William J. Wiehagen

Forty-eight workers who bad escaped large underground coal-mine fires were interviewed using an open-ended protocol. This information, and the actual experiences of one eight-person mine-section crew who escaped from a Fire, were used to construct an 18-frame (page) table-top simulation exercise, which was then field tested with 134 miners. The exercise is a research toot that measures miners' proficiency in the information-gathering and decision-making skills related to escaping from a mine fire. It also helps miners to learn and practice these cognitive skills. The exercise was found to be valid and reliable. All miners reported that the exercise was authentic and would help them to remember important information. The exercise total score, and all but two item scores, significantly discriminated among miners with different levels of training. The two items that did not discriminate dealt with whether or not to abandon a helpless fellow miner. When the exercise total score data were pooled, only 13.6% of the miners achieved a desirable score of 90% mastery or greater. The simulation is important because it teaches and assesses critical judgment and derision-making skills that are rarely addressed in miner training. Index Terms- Coal mining, critical skills, decision making, emergency escape and evacuation, escape from fire judgment training, mining, safety training, simulation training, under-ground mine fires.

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

4. Preliminary Study - Remote Seal Checker 4.1 Introduction Determination of the completeness of each individual seal at the time of its emplacement is essential for an effective remote sealing system. A satisfactory seal checking technique should provide a signal which: (1) indicates percentage completion as the seal is emplaced (2) provides a definite indication of a complete seal (3) indicates the size of the unsealed area if a complete seal is not feasible This information is required to establish the need for additional seal material, the need for additional seals, and the risk likely involved in entering the mine., In many situations it is as important to know the quality of a seal as it is to build an effective one. It is likely that with repeated use the remote sealing technique developed by Foster-Miller Associates will be sufficiently reliable and predictable to preclude the seal checking requirement. It is recommended, however, that each seal be checked during construction to insure its completeness and increase the level of confidence so necessary in reopening the mine. 4.2 Description of General Problem Several characteristics of remote mine seals are important in considering techniques for evaluating the effectiveness of these seals. These include:

Jan 1, 1973

By C. Melvin Lepper

A solid-state amplifier for the bridge circuit of an atomic-absorption mercury detector is presented and described. Operational advantages over previously used circuitry include improved time and temperature stability, increased measurement accuracy, and simplified setup, calibration, and operation.

Jan 1, 1972

By Steven W. Schmauch

The Sugarloaf RARE II area (No. 5296) covers 11,100 acres in the northern part of the White Mountain Range, in the Inyo fictional Forrest. It is in Nevada, about 45 mi north of Bishop, California. A mineral survey was conducted by On U.S. burro of Mines in 1982 and by the U.S. Geological Survey in 1980-1982. The Bureau reviewed pertinent literature, searched Esmeralda and Mineral County mining records, obtained current claim information from the administrative agencies, and contacted claim owners. Thirty-six properties were examined, and 674 samples were taken from them to help assess win oral resources and potential. The Geological Survey evaluated the regional mineral potential by geologic, geochemical, and Geophysical surveys.

Jan 1, 1983

By Halagowder Devaraj, Mostafa Sheykhnazari, Veer P. Bhavanandan

"A sensitive colorimetric assay for detecting mucins and glycoproteins rich in 0-glycosidically linked saccharides is reported. The method combines the susceptibility of N-acetylgalactosamine terminating 0-glyco idically linked saccharides to P-elimination with the Morgan-Elson reaction for N-acetylhexosamines with free reducing ends. All mucin and mucin-type glycoproteins but none of the serum-type glycoproteins tested resulted in characteristic color production. All mucins tested gave linear responses in the range 5 to 200 ""g and the assay was also adapted to the microscale involving the use of 96-well microtiter plates. The microassay in which the volumes of samples and reagents are scaled down 2.5-fold was particularly useful in monitoring of mucins, in the presence of other glycoconjugates, in large numbers of samples obtained during fractionation procedures. Cesium chloride, cesium bromide, potassium thiocyanate, and various detergents do not interfere with the colorimetric determination. Guanidine hydrochloride, cesium triftuoroacetate, and B-mercap- . toethanol decreased color by 30 to 45%; however, the interference was not serious to prevent the use of the method for detection of mucins in their presence. The use of the method for the specific detection of mucin during fractionation by gel filtration and density gradient centrifugation of cystic fibrosis sputum samples is demonstrated. Mucins are an important class of biomacromolecules whose structure-function relationship is poorly understood (1,2). The investigations of mucins are hampered by difficulties in purifying these very large size molecules which appear to avidly bind other components of the mucus (3,4). One of the problems during purification is the specific detection of mucins. For example, during the various purification steps, the fractions containing mucins are typically detected by assaying for neutral sugars (hexoses) (5,6), for sialic acids (7), or for periodate oxidizable saccharide units (8). However, these methods are not entirely satisfactory because neutral sugars, sialic acids, and periodate-oxidizable saccharides are also components of other glycoconjugates. In addition, the neutral sugar and sialic acid measurements are also subject to interference from high levels of proteins and nucleic acids."

Jan 1, 1990

By Charles D. Litton

Experiments were conducted to determine the optical scattering properties of diesel particulate matter (DPM) and various combustion aerosols from both flaming and smoldering combustion sources at discrete angles of 151 and 301 in the forward direction and at a light source wave length of 635 nm using a simple light scattering module. In addition to the scattering data, simultaneous measurements were made of the total aerosol mass concentration; light extinction at an average wave length of 546nm; and the response of a common bipolar ion chamber typical of residential smoke detectors modified to allow the aerosols to flow through the chamber. The results of these experiments indicate, for DPM and combustion aerosols, the intensities per unit mass concentration depend not only upon whether the aerosolis DPM or combustion aerosol but also upon the type of combustion aerosol. The results also indicate that the ion chamber responses are greatest for DPM, followed by the response to flaming combustion aerosols (FCA)and lowest for smoldering combustion aerosols (SCA). For light scattering, the greatest intensities are found for SCA, followed by the intensities from FCA, and lowest for DPM. This report describes the experiments, their results, and the use of these results to developed sign criteria for early warning fire sensor capable of the rapid and reliable detection of fires in atmospheres that may or may not be contaminated by the products produced from diesel engines. © 2002 Elsevier Science Ltd. All rights reserved.